Alternating current heating techniques for lithium-ion batteries in electric vehicles:Recent advances and perspectives

The significant decrease in battery performance at low temperatures is one of the critical challenges that electric vehicles(EVs)face,thereby affecting the penetration rate in cold regions.Alternating current(AC)heating has attracted widespread attention due to its low energy consumption and uniform heating advantages.This paper introduces the recent advances in AC heating from the perspective of practical EV applications.First,the performance degradation of EVs in low-temperature environments is introduced briefly.The concept of AC heating and its research methods are provided.Then,the effects of various AC heating methods on battery heating performance are reviewed.Based on existing studies,the main factors that affect AC heating performance are analyzed.Moreover,various heating circuits based on EVs are categorized,and their cost,size,complexity,efficiency,reliability,and heating rate are elaborated and compared.The evolution of AC heaters is presented,and the heaters used in brand vehicles are sorted out.Finally,the perspectives and challenges of AC heating are discussed.This paper can guide the selection of heater implementation methods and the optimization of heating effects for future EV applications.

Wetting alternating with partial drying during grain filling increases lysine biosynthesis in inferior rice grain

Lysine content is a criterion of the nutritional quality of rice.Understanding the process of lysine biosynthesis in early-flowering superior grain(SG)and late-flowering inferior grain(IG)of rice would advance breeding and cultivation to improve nutritional quality.However,little information is available on differences in lysine anabolism between SG and IG and the underlying mechanism,and whether and how irrigation regimes affect lysine anabolism in these grains.A japonica rice cultivar was grown in the field and two irrigation regimes,continuous flooding(CF)and wetting alternating with partial drying(WAPD),were imposed from heading to the mature stage.Lysine content and activities of key enzymes of lysine biosynthesis,and levels of brassinosteroids(BRs)were lower in the IG than in the SG at the early grainfilling stage but higher at middle and late grain-filling stages.WAPD increased activities of these key enzymes,BR levels,and contents of lysine and total amino acids in IG,but not SG relative to CF.Application of 2,4-epibrassinolide to rice panicles in CF during early grain filling reproduced the effects of WAPD,but neither treatment altered the activities of enzymes responsible for lysine catabolism in either SG or IG.WAPD and elevated BR levels during grain filling increased lysine biosynthesis in IG.Improvement in lysine biosynthesis in rice should focus on IG.

Suppression of stimulated Brillouin and Raman scatterings using an alternating frequency laser and transverse magnetic fields

A novel scheme to suppress both stimulated Brillouin scattering(SBS) and stimulated Raman scattering(SRS) by combining an alternating frequency(AF) laser and a transverse magnetic field is proposed. The AF laser allows the laser frequency to change discretely and alternately over time. The suppression of SBS is significant as long as the AF difference is greater than the linear growth rate of SBS or the alternating time of the laser frequency is shorter than the linear growth time of SBS. However, the AF laser proves ineffective in suppressing SRS, which usually has a much higher linear growth rate than SBS. To remedy that, a transverse magnetic field is included to suppress the SRS instability. The electrons trapped in the electron plasma waves(EPWs) of SRS can be accelerated by the surfatron mechanism in a transverse magnetic field and eventually detrapped. While continuously extracting energy from EPWs, the EPWs are dissipated and the kinetic inflation of SRS is suppressed. The one-dimensional particle-in-cell simulation results show that both SBS and SRS can be effectively suppressed by combining the AF laser with a transverse magnetic field with tens of Tesla. The total reflectivity can be dramatically reduced by more than one order of magnitude. These results provide a potential reference for controlling SBS and SRS under the related parameters of inertial confinement fusion.

Diagnosing ratio of electron density to collision frequency of plasma surrounding scaled model in a shock tube using low-frequency alternating magnetic field phase shift

A non-contact low-frequency(LF)method of diagnosing the plasma surrounding a scaled model in a shock tube is proposed.This method utilizes the phase shift occurring after the transmission of an LF alternating magnetic field through the plasma to directly measure the ratio of the plasma loop average electron density to collision frequency.An equivalent circuit model is used to analyze the relationship of the phase shift of the magnetic field component of LF electromagnetic waves with the plasma electron density and collision frequency.The applicable range of the LF method on a given plasma scale is analyzed.The upper diagnostic limit for the ratio of the electron density(unit:m^(-3))to collision frequency(unit:Hz)exceeds 1×10^(11),enabling an electron density to exceed 1×10^(20)m^(-3)and a collision frequency to be less than 1 GHz.In this work,the feasibility of using the LF phase shift to implement the plasma diagnosis is also assessed.Diagnosis experiments on shock tube equipment are conducted by using both the electrostatic probe method and LF method.By comparing the diagnostic results of the two methods,the inversion results are relatively consistent with each other,thereby preliminarily verifying the feasibility of the LF method.The ratio of the electron density to the collision frequency has a relatively uniform distribution during the plasma stabilization.The LF diagnostic path is a loop around the model,which is suitable for diagnosing the plasma that surrounds the model.Finally,the causes of diagnostic discrepancy between the two methods are analyzed.The proposed method provides a new avenue for diagnosing high-density enveloping plasma.

Evaluation of the dynamic sealing performance of cap rocks of underground gas storage under multi-cycle alternating loads

The static sealing of underground gas storage(UGS),including the integrity of cap rocks and the stability of faults,is analyzed from a macro perspective using a comprehensive geological evaluation method.Changes in pore structure,permeability,and mechanical strength of cap rocks under cyclic loads may impact the rock sealing integrity during the injection and recovery phases of UGS.In this work,the mechanical deformation and failure tests of rocks,as well as rock damage tests under alternating loads,are conducted to analyze the changes in the strength and permeability of rocks under multiple-cycle intense injection and recovery of UGS.Additionally,this study proposes an evaluation method for the dynamic sealing performance of UGS cap rocks under multi-cycle alternating loads.The findings suggest that the failure strength(70%)can be used as the critical value for rock failure,thus providing theoretical support for determining the upper limit of operating pressure and the number of injection-recovery cycles for the safe operation of a UGS system.

Sediment Movement in Periodic Alternating Current

The present paper summarizes the results of previous studies, including the structure and principle of the rotary ring flume for researching the fine sediment movement, the mechanism of the flume, method of eliminating the influence of the centrifugal force and sediment movement experiments with periodic alternating current. Also included are the experiment-based relationship among sediment concentration, bed shear stress and silt carrying capacity, a proposed erosion-deposition function and bed erosion-deposition calculation together with the results of verification.

Mechanism of plasticity enhancement of AZ31B magnesium alloy sheet by accumulative alternating back extrusion

Accumulative alternating back extrusion was a potential fine-grain modification method.In this paper,it was an innovative attempt to develop high-performance magnesium alloy sheet by this process.Under the condition of 350 K,commercial AZ31 magnesium alloy was made into billet by accumulative alternating back extrusion,and then extruded into fine-grain magnesium alloy sheet.Through a systematic study of its microstructure and mechanical properties,the results showed that the initial state had an important influence on the evolution of the structure during extrusion.After accumulative alternating back extrusion to produce the billet,the grain size of the sheet obtained by extrusion was significantly refined,which was related to the accumulation of deformation and grain refinement during the alternating loading process.Grain refinement caused the proportion of dynamic recrystallization inside the sheet with 2 cycles of accumulative alternating back extrusion to drop to 27%.With the increase of extrusion cycles from 2 to 4,the high density of dislocations led to an increase in the proportion of dynamic recrystallization and finer grains.The texture changed from strong basal texture to weak bimodal texture.The results of uniaxial tensile test show that due to grain refinement and texture change,the yield strength was significantly reduced,and the plasticity was significantly improved.It was verified that accumulative alternating back extrusion was meaningful for subsequent processing,and it also provided scientific guidance for the development of fine-grained magnesium alloy sheet.

Texture property and weakening mechanism of Mg-3Al-1Zn alloy by interactive alternating forward extrusion

The interactive alternating forward extrusion(AFE) method can realize the change of texture type and the weakening of texture strength.Taking AZ31 magnesium alloy as an example, the texture evolution of interactive AFE was studied. The results show that all kinds of dynamic recrystallization(DRX) behaviors can weaken the texture to vary degrees. The weakening effect of twinning-induced recrystallization(TDRX)behavior was particularly significant. During the interactive AFE process, the c-axis of most grains rotated under the external force, and tended to be 90° angle with the ED direction, forming a stable fiber texture. In addition, with the increase of loading passes, the starting of {0001} <11–20> basal slip system became more and more difficult. The(10–10) texture formed by {10–10} <11–20> prismatic slip system after sixth passes was the main texture type. With the increase of forming temperature, the starting ability of {10–10} <11–20>prismatic slip systems increased, and the(10–10) texture formed by prismatic slip system above 623 K dominated.

Low-complexity iterative equalization for OTFS based on alternating minimization

To achieve robust communication in high mobility scenarios,an iterative equalization algorithm based on alternating minimization(AM)is proposed for the orthogonal time frequency space(OTFS)system.The algorithm approximates the equalization problem to a convex function optimization problem in the real-valued domain and solves the problem iteratively using the AM algorithm.In the iterative process,the complexity of the proposed algorithm is reduced further based on the study of the cyclic structure and sparse property of the OTFS channel matrix in the delay-Doppler(DD)domain.The new method for OTFS is simulated and verified in a high-speed mobile scenario and the results show that the proposed equalization algorithm has excellent bit error rate performance with low complexity.

A Relationship between the Partial Bell Polynomials and Alternating Run Polynomials

In this note, we first derive an exponential generating function of the alternating run polynomials. We then deduce an explicit formula of the alternating run polynomials in terms of the partial Bell polynomials.

New atom movement mechanism for tracking path on disordering AuCuI(A_8^(Au)A_4^(Cu)) compound

Taking experimental path on disordering AuCuI（AAuCu8A4）composed of A Au8 and ACu4 stem alloy genes as an example, three discoveries and a method were presented. The ability of Au Cu I（AAu Cu8 A4）to keep structure stabilization against changing temperature is attributed to the fact that the AAu8 and ACu4 potential well depths greatly surpass their vibration energies, which leads to the subequilibrium of experimental path. A new atom movement mechanism of AuCuI（AAuACu84）to change structure for suiting variation in temperature is the resonance activating-synchro alternating of alloy genes, which leads to heterogeneous and successive subequilibrium transitions. There exists jumping order degree, which leads to the existence of jumping Tj-temperature and an unexpected so-called ＂retro-effect＂ about jumping temperature retrograde shift to lower temperatures upon the increasing heating rate. A set of subequilibrium holographic network path charts were obtained by the experimental mixed enthalpy path method.

Improving the nutritional values of yellow mealworm Tenebrio molitor(Coleoptera: Tenebrionidae) larvae as an animal feed ingredient: a review

Yellow mealworm larvae(YML;Tenebrio molitor) are considered as a valuable insect species for animal feed due to their high nutritional values and ability to grow under different substrates and rearing conditions. Advances in the understanding of entomophagy and animal nutrition over the past decades have propelled research areas toward testing multiple aspects of YML to exploit them better as animal feed sources. This review aims to summarize various approaches that could be exploited to maximize the nutritional values of YML as an animal feed ingredient. In addition, YML has the potential to be used as an antimicrobial or bioactive agent to improve animal health and immune function in production animals. The dynamics of the nutritional profile of YML can be influenced by multiple factors and should be taken into account when attempting to optimize the nutrient contents of YML as an animal feed ingredient. Specifically, the use of novel land-based and aquatic feeding resources, probiotics, and the exploitation of larval gut microbiomes as novel strategies can assist to maximize the nutritional potential of YML. Selection of relevant feed supplies, optimization of ambient conditions, the introduction of novel genetic selection procedures, and implementation of effective post-harvest processing may be required in the future to commercialize mealworm production. Furthermore, the use of appropriate agricultural practices and technological improvements within the mealworm production sector should be aimed at achieving both economic and environmental sustainability. The issues highlighted in this review could pave the way for future approaches to improve the nutritional value of YML.

Fast alternating direction method of multipliers for total-variation-based image restoration

A novel algorithm, i.e. the fast alternating direction method of multipliers （ADMM）, is applied to solve the classical total-variation （ TV ）-based model for image reconstruction. First, the TV-based model is reformulated as a linear equality constrained problem where the objective function is separable. Then, by introducing the augmented Lagrangian function, the two variables are alternatively minimized by the Gauss-Seidel idea. Finally, the dual variable is updated. Because the approach makes full use of the special structure of the problem and decomposes the original problem into several low-dimensional sub-problems, the per iteration computational complexity of the approach is dominated by two fast Fourier transforms. Elementary experimental results indicate that the proposed approach is more stable and efficient compared with some state-of-the-art algorithms.

Effect of Artificial Electric Field Surface by Wave-Driven Triboelectricity on Anti-Bioadhesion for Riser Protection

Biofouling has been a persistent problem in marine riser system, resulting in energy waste and equipment damage. Inthis study, a kind of water wave-driven contact-mode flexible triboelectric nanogeneration has been prepared byusing graphene-doped PDMS as dielectric friction material. When the graphene content is 2%, the average outputvoltage can reach 46 V under the contact frequency 10 Hz. The flexible triboelectric nanogeneration encapsulationmodule is impinged by water waves to generate alternating microelectric field on the riser surface and destroy theadhesion conditions of microorganisms during the biofilm stage. In the biofouling experiments at different stages, thebiofouling area of the platymonas subcordiformis has been reduced by 53%, 62% and 61%. It provides a new ideafor effective treatment of biofouling of mussels, oysters and barnacles attached to risers.

Alternative splicing of the PECTINESTERASE gene encoding a cell wall-degrading enzyme affects postharvest softening in grape

The firmness of table grape berries is a crucial quality parameter. Despite extensive research on postharvest fruit softening, its precise molecular mechanisms remain elusive. To enhance our comprehension of the underlying molecular factors, we initially identified differentially expressed genes(DEGs) by comparing the transcriptomes of folic acid(FA)-treated and water-treated(CK) berries at different time points. We then analyzed the sequences to detect alternatively spliced(AS) genes associated with postharvest softening. A total of 2,559 DEGs were identified and categorized into four subclusters based on their expression patterns, with subcluster-4 genes exhibiting higher expression in the CK group compared with the FA treatment group. There were 1,045 AS-associated genes specific to FA-treated berries and 1,042 in the CK-treated berries, respectively. Gene Ontology(GO) annotation indicated that the AS-associated genes in CK-treated berries were predominantly enriched in cell wall metabolic processes,particularly cell wall degradation processes. Through a comparison between treatment-associated AS genes and subcluster-4 DEGs, we identified eight genes, including Pectinesterase 2(VvPE2, Vitvi15g00704), which encodes a cell wall-degrading enzyme and was predicted to undergo an A3SS event. The reverse transcription polymerase chain reaction further confirmed the presence of a truncated transcript variant of VvPE2 in the FA-treated berries.Our study provides a comprehensive analysis of AS events in postharvest grape berries using transcriptome sequencing and underscores the pivotal role of VvPE2 during the postharvest storage of grape berries.

Impact Force Localization and Reconstruction via ADMM-based Sparse Regularization Method

In practice,simultaneous impact localization and time history reconstruction can hardly be achieved,due to the illposed and under-determined problems induced by the constrained and harsh measuring conditions.Although l_(1) regularization can be used to obtain sparse solutions,it tends to underestimate solution amplitudes as a biased estimator.To address this issue,a novel impact force identification method with l_(p) regularization is proposed in this paper,using the alternating direction method of multipliers(ADMM).By decomposing the complex primal problem into sub-problems solvable in parallel via proximal operators,ADMM can address the challenge effectively.To mitigate the sensitivity to regularization parameters,an adaptive regularization parameter is derived based on the K-sparsity strategy.Then,an ADMM-based sparse regularization method is developed,which is capable of handling l_(p) regularization with arbitrary p values using adaptively-updated parameters.The effectiveness and performance of the proposed method are validated on an aircraft skin-like composite structure.Additionally,an investigation into the optimal p value for achieving high-accuracy solutions via l_(p) regularization is conducted.It turns out that l_(0.6)regularization consistently yields sparser and more accurate solutions for impact force identification compared to the classic l_(1) regularization method.The impact force identification method proposed in this paper can simultaneously reconstruct impact time history with high accuracy and accurately localize the impact using an under-determined sensor configuration.

Secure Transmission Scheme for Blocks in Blockchain-Based Unmanned Aerial Vehicle Communication Systems

In blockchain-based unmanned aerial vehicle(UAV)communication systems,the length of a block affects the performance of the blockchain.The transmission performance of blocks in the form of finite character segments is also affected by the block length.Therefore,it is crucial to balance the transmission performance and blockchain performance of blockchain communication systems,especially in wireless environments involving UAVs.This paper investigates a secure transmission scheme for blocks in blockchain-based UAV communication systems to prevent the information contained in blocks from being completely eavesdropped during transmission.In our scheme,using a friendly jamming UAV to emit jamming signals diminishes the quality of the eavesdropping channel,thus enhancing the communication security performance of the source UAV.Under the constraints of maneuverability and transmission power of the UAV,the joint design of UAV trajectories,transmission power,and block length are proposed to maximize the average minimum secrecy rate(AMSR).Since the optimization problem is non-convex and difficult to solve directly,we first decompose the optimization problem into subproblems of trajectory optimization,transmission power optimization,and block length optimization.Then,based on firstorder approximation techniques,these subproblems are reformulated as convex optimization problems.Finally,we utilize an alternating iteration algorithm based on the successive convex approximation(SCA)technique to solve these subproblems iteratively.The simulation results demonstrate that our proposed scheme can achieve secure transmission for blocks while maintaining the performance of the blockchain.

Comparison of the effect of different external electrodes on discharge plasma-assisted diffusion flame stabilization

To optimize the design of plasma injectors,the influence of different external electrodes on plasma-assisted flame stabilization was assessed by using a nonequilibrium plasma injector flame control setup.The electrical characteristics of the injector,flame structure parameters,flame intensity,discharge power,and cost-to-effectiveness ratio under different external electrodes(four mesh electrodes and one copper foil electrode)were analyzed using electrical and optical methods.The results show that reducing the mesh size of the external electrode leads to a decrease in breakdown voltage.Compared with a ceramic dielectric barrier-based injector,an injector with a quartz dielectric barrier produces a higher breakdown voltage under the same conditions.For the same actuation voltage,the discharge current increases as the mesh size of the external electrode decreases,and combustion is enhanced by the discharge plasma;therefore,it is better to adopt a smaller mesh hole size to realize good flame stabilization under a lower actuation voltage.However,under the studied working conditions,reducing the mesh hole size of the external electrode increases the cost-to-effectiveness ratio of plasma injector-based flame stabilization.Thus,considering the cost-to-effectiveness ratio and the weight of the injector,an external electrode with a larger mesh hole size should be chosen,which contradicts the above rule.

Joint Active and Passive Beamforming Design for Hybrid RIS-Aided Integrated Sensing and Communication

Integrated sensing and communication(ISAC) is considered an effective technique to solve spectrum congestion in the future. In this paper, we consider a hybrid reconfigurable intelligent surface(RIS)-assisted downlink ISAC system that simultaneously serves multiple single-antenna communication users and senses multiple targets. Hybrid RIS differs from fully passive RIS in that it is composed of both active and passive elements, with the active elements having the effect of amplifying the signal in addition to phase-shifting. We maximize the achievable sum rate of communication users by collaboratively improving the beamforming matrix at the dual function base station(DFBS) and the phase-shifting matrix of the hybrid RIS, subject to the transmit power constraint at the DFBS, the signal-to-interference-plus-noise-ratio(SINR) constraint of the radar echo signal and the RIS constraint are satisfied at the same time. The builtin RIS-assisted ISAC design problem model is significantly non-convex due to the fractional objective function of this optimization problem and the coupling of the optimization variables in the objective function and constraints. As a result, we provide an effective alternating optimization approach based on fractional programming(FP) with block coordinate descent(BCD)to solve the optimization variables. Results from simulations show that the hybrid RIS-assisted ISAC system outperforms the other benchmark solutions.

RNA m6A dynamic modification mediated by nucleuslocalized FTO is involved in follicular reserve

In eukaryotic organisms,the most common internal modification of messenger RNA(m RNA)is N6-methyladenosine(m6A).This modification can be dynamically and reversibly controlled by specific enzymes known as m6A writers and erasers.The fat-mass and obesity-associated protein(FTO)catalyzes RNA demethylation and plays a critical role in various physiological and pathological processes.Our research identified dynamic alterations in both m6A and FTO during the assembly of primordial follicles,with an inverse relationship observed for m6A levels and nuclear-localized FTO expression.Application of Fto small interfering RNA(si RNA)altered the expression of genes related to cell proliferation,hormone regulation,and cell chemotaxis,and affected RNA alternative splicing.Overexpression of the full-length Fto gene led to changes in m6A levels,alternative splicing of Cdk5,cell proliferation,cell cycle progression,and proportion of primordial follicles.Conversely,overexpression of Fto lacking a nuclear localization signal(NLS)did not significantly alter m6A levels or primordial follicle assembly.These findings suggest that FTO,localized in the nucleus but not in the cytoplasm,regulates RNA m6A demethylation and plays a role in cell proliferation,cell cycle progression,and primordial follicle assembly.These results highlight the potential of m6A and its eraser FTO as possible biomarkers and therapeutic targets.