NiFe2O4-10NiO-based cermet inert anodes for aluminium electrolysis were prepared and their properties were investigated in a lab-scale electrolysis cell. The results show that the inert anodes exhibit good performance...NiFe2O4-10NiO-based cermet inert anodes for aluminium electrolysis were prepared and their properties were investigated in a lab-scale electrolysis cell. The results show that the inert anodes exhibit good performance during electrolysis in molten salt cryolite at 960 °C, but according to the analyses of phase compositions and microstructures through XRD, SEM/EDX and metallographic analysis, the metal in the anodes is preferentially corroded and many pores are produced on the anode surface after electrolysis. The preferential dissolution of Fe in the NiFe2O4 phase may lead to the non-uniform corrosion of NiFe2O4 grains. Moreover, a dense protective layer of NiFe2O4-NiAl2O4-FeAl2O4 is formed on the anode surface, which originates from the reaction of Al2O3 dissolved in the electrolyte with NiO or FeO, the annexation of NiFe2O4-NiAl2O4-FeAl2O4 to NiO and volume expansion. Thus, the dense NiFe2O4-NiAl2O4-FeAl2O4 layer inhibits the metal loss and ceramic-phase corrosion on the surface of the cermet inert anodes.展开更多
The selection of milling tools for Si C14Cu4Mg0.5Si based on Aluminium matrix 2A14 was analyzed, and the factors that affect the efficiency of the milling were discussed. The Si C14Cu4Mg0.5Si was designed for use on t...The selection of milling tools for Si C14Cu4Mg0.5Si based on Aluminium matrix 2A14 was analyzed, and the factors that affect the efficiency of the milling were discussed. The Si C14Cu4Mg0.5Si was designed for use on the moon landing vehicle or missile wings, but the hardness of aluminium-silicon carbide composite material was very high, much higher than the general hardness of cemented carbide, which will bring many difficulties in the aluminium-silicon carbide composite material processing. The chemical compositions of Si C14Cu4Mg0.5Si were analyzed. A new selected indexable cutter was designed to mill Si C14Cu4Mg0.5Si. The structure design of milling cutter was different from the conventional milling cutter, breaking the previous limitations to a certain extent, pioneering the idea. The tool material wear was detected by experiments. The mechanical and physical properties of Si C14Cu4Mg0.5Si were also tested. Si C14Cu4Mg0.5Si exhibited different surface quality characteristics under different milling tools.展开更多
The conditions of color reaction of Aluminium(Ⅲ) with a new organic reagent 2,3,7 trihydroxy 9 [2,4 dihydroxy)phenylazo]phenylfluorone (ARPF) in the presence of cetyltrimethyammonium bromide(CTMAB) were studied....The conditions of color reaction of Aluminium(Ⅲ) with a new organic reagent 2,3,7 trihydroxy 9 [2,4 dihydroxy)phenylazo]phenylfluorone (ARPF) in the presence of cetyltrimethyammonium bromide(CTMAB) were studied. It was found that Aluminium(Ⅲ) reacts with ARPF and CTMAB in pH 6.5 HAc NaAc buffer solution to form a 1∶2 red complex with maximum absorption at 562 nm .The molar absorptivity is 1.10×10 5 L·mol -1 ·cm -1 . Beer's law is obeyed in the range of 0 5.5 μg Al(Ⅲ) per 25 mL. The method has been applied to determination of Aluminium in the limestone with satisfactory results.展开更多
This work intends to investigate the inhibition behaviour of 2-butine 1, 4diol and potassium sodium tartrate and their synergistic effects on 3003 aluminium alloy corrosion in 0.5% NaCl solution. Experiments were carr...This work intends to investigate the inhibition behaviour of 2-butine 1, 4diol and potassium sodium tartrate and their synergistic effects on 3003 aluminium alloy corrosion in 0.5% NaCl solution. Experiments were carried out by electrochemical impedance spectroscopy （EIS） and Tafel polarization method in a three-electrode cell. It was concluded that the inhibition efficiencies increased with an increase in the concentrations of inhibitors. For 2-butinel, 4diol and tartrate salt, the optimum in the inhibition efficiency, at room temperature and neutral pH, was observed for concentrations close to 10-3 mol/L and 1.5×10^-3mol/L, respectively. The electrochemical results illustrated that 2-butinel, 4diol and tartrate salt, have significant synergistic inhibition effects on corrosion of 3003 aluminium alloy in 0.5% NaCl solution. The optimum ratio of concentrations for tartrate to alcohol was 2：1.展开更多
The aim of this work has been to evaluate the aluminium (Al(III)) traces contents in 24-hour urine samples from subjects with different tobacco smoke expositions using a new methodology with 1,4-dihydroxy-9, 10-anthra...The aim of this work has been to evaluate the aluminium (Al(III)) traces contents in 24-hour urine samples from subjects with different tobacco smoke expositions using a new methodology with 1,4-dihydroxy-9, 10-anthraquinone (Quinizarine, QZ) as a fluorosphore. Biological samples were tested using commercial reagent strips and clinical parameters. Al(III) was determined complexing with QZ followed by a solid phase extraction step using Nylon membranes as a solid support. The analyte was subsequently quantified by solid surface fluorescence (SSF, λem= 573, λexc= 490) with a detection limit of 0.88 μg L-1 and quantification limit of 2.69 μg L-1. The calibration curve was linear from 2.69 to 499.13 μg L-1 Al(III) (R2 = 0.9973). Urine samples were successfully analysed with an average recovery close to 100%. Solid phase extraction step showed efficacy to eliminate foreign ions and the highly fluorescent matrix own of urine. Results were validated by electrothermal atomic absorption spectrometry (ETAAS) with an adequate concordance. The new methodology has low operation cost with simple instrumentation and without organic solvent.展开更多
基金Project (2012FJ6123) supported by the Project of Science and Technology of Hunan Province,ChinaProject supported by Post-Doctoral Foundation of Central South University,China+1 种基金Project (CL12100) supported the Undergraduate Innovative Training of Central South University,ChinaProject (2282013bkso13) supported by Free Exploration Plan of Central South University,China
文摘NiFe2O4-10NiO-based cermet inert anodes for aluminium electrolysis were prepared and their properties were investigated in a lab-scale electrolysis cell. The results show that the inert anodes exhibit good performance during electrolysis in molten salt cryolite at 960 °C, but according to the analyses of phase compositions and microstructures through XRD, SEM/EDX and metallographic analysis, the metal in the anodes is preferentially corroded and many pores are produced on the anode surface after electrolysis. The preferential dissolution of Fe in the NiFe2O4 phase may lead to the non-uniform corrosion of NiFe2O4 grains. Moreover, a dense protective layer of NiFe2O4-NiAl2O4-FeAl2O4 is formed on the anode surface, which originates from the reaction of Al2O3 dissolved in the electrolyte with NiO or FeO, the annexation of NiFe2O4-NiAl2O4-FeAl2O4 to NiO and volume expansion. Thus, the dense NiFe2O4-NiAl2O4-FeAl2O4 layer inhibits the metal loss and ceramic-phase corrosion on the surface of the cermet inert anodes.
基金Funded by the National Natural Science Foundation of China(Nos.51275490,and 51475346)Specialized Research Fund for the Doctoral Program of Higher Education of China(20131420120002)Shanxi Province Science Foundation(2013011025-1)
文摘The selection of milling tools for Si C14Cu4Mg0.5Si based on Aluminium matrix 2A14 was analyzed, and the factors that affect the efficiency of the milling were discussed. The Si C14Cu4Mg0.5Si was designed for use on the moon landing vehicle or missile wings, but the hardness of aluminium-silicon carbide composite material was very high, much higher than the general hardness of cemented carbide, which will bring many difficulties in the aluminium-silicon carbide composite material processing. The chemical compositions of Si C14Cu4Mg0.5Si were analyzed. A new selected indexable cutter was designed to mill Si C14Cu4Mg0.5Si. The structure design of milling cutter was different from the conventional milling cutter, breaking the previous limitations to a certain extent, pioneering the idea. The tool material wear was detected by experiments. The mechanical and physical properties of Si C14Cu4Mg0.5Si were also tested. Si C14Cu4Mg0.5Si exhibited different surface quality characteristics under different milling tools.
文摘The conditions of color reaction of Aluminium(Ⅲ) with a new organic reagent 2,3,7 trihydroxy 9 [2,4 dihydroxy)phenylazo]phenylfluorone (ARPF) in the presence of cetyltrimethyammonium bromide(CTMAB) were studied. It was found that Aluminium(Ⅲ) reacts with ARPF and CTMAB in pH 6.5 HAc NaAc buffer solution to form a 1∶2 red complex with maximum absorption at 562 nm .The molar absorptivity is 1.10×10 5 L·mol -1 ·cm -1 . Beer's law is obeyed in the range of 0 5.5 μg Al(Ⅲ) per 25 mL. The method has been applied to determination of Aluminium in the limestone with satisfactory results.
文摘This work intends to investigate the inhibition behaviour of 2-butine 1, 4diol and potassium sodium tartrate and their synergistic effects on 3003 aluminium alloy corrosion in 0.5% NaCl solution. Experiments were carried out by electrochemical impedance spectroscopy （EIS） and Tafel polarization method in a three-electrode cell. It was concluded that the inhibition efficiencies increased with an increase in the concentrations of inhibitors. For 2-butinel, 4diol and tartrate salt, the optimum in the inhibition efficiency, at room temperature and neutral pH, was observed for concentrations close to 10-3 mol/L and 1.5×10^-3mol/L, respectively. The electrochemical results illustrated that 2-butinel, 4diol and tartrate salt, have significant synergistic inhibition effects on corrosion of 3003 aluminium alloy in 0.5% NaCl solution. The optimum ratio of concentrations for tartrate to alcohol was 2：1.
文摘The aim of this work has been to evaluate the aluminium (Al(III)) traces contents in 24-hour urine samples from subjects with different tobacco smoke expositions using a new methodology with 1,4-dihydroxy-9, 10-anthraquinone (Quinizarine, QZ) as a fluorosphore. Biological samples were tested using commercial reagent strips and clinical parameters. Al(III) was determined complexing with QZ followed by a solid phase extraction step using Nylon membranes as a solid support. The analyte was subsequently quantified by solid surface fluorescence (SSF, λem= 573, λexc= 490) with a detection limit of 0.88 μg L-1 and quantification limit of 2.69 μg L-1. The calibration curve was linear from 2.69 to 499.13 μg L-1 Al(III) (R2 = 0.9973). Urine samples were successfully analysed with an average recovery close to 100%. Solid phase extraction step showed efficacy to eliminate foreign ions and the highly fluorescent matrix own of urine. Results were validated by electrothermal atomic absorption spectrometry (ETAAS) with an adequate concordance. The new methodology has low operation cost with simple instrumentation and without organic solvent.
