Microwave electrometry with Rydberg atoms in a vapor cell using microwave amplitude modulation

We have theoretically and experimentally studied the dispersive signal of the Rydberg atomic electromagneticallyinduced transparency(EIT)Autler–Townes(AT)splitting spectra obtained using amplitude modulation of the microwave(MW)electric field.In addition to the two zero-crossing points interval△f_(zeros),the dispersion signal has two positive maxima with an interval defined as the shoulder interval△f_(sho),which is theoretically expected to be used to measure a much weaker MW electric field.The relationship of the MW field strength E_(MW)and△f_(sho)is experimentally studied at the MW frequencies of 31.6 GHz and 9.2 GHz respectively.The results show that△f_(sho)can be used to characterize the much weaker E_(MW)than that of△f_(zeros)and the traditional EIT–AT splitting interval△f_(m);the minimum E_(MW)measured by△f_(sho)is about 30 times smaller than that by△f_(m).As an example,the minimum E_(MW)at 9.2 GHz that can be characterized by△f_(sho)is 0.056 mV/cm,which is the minimum value characterized by the frequency interval using a vapor cell without adding any auxiliary fields.The proposed method can improve the weak limit and sensitivity of E_(MW)measured by the spectral frequency interval,which is important in the direct measurement of weak E_(MW).

Altered spontaneous brain activity patterns in hypertensive retinopathy using fractional amplitude of low-frequency fluctuations:a functional magnetic resonance imaging study

AIM:To study functional brain abnormalities in patients with hypertensive retinopathy(HR)and to discuss the pathophysiological mechanisms of HR by fractional amplitude of low-frequency fluctuations(fALFFs)method.METHODS:Twenty HR patients and 20 healthy controls(HCs)were respectively recruited.The age,gender,and educational background characteristics of the two groups were similar.After functional magnetic resonance imaging(fMRI)scanning,the subjects’spontaneous brain activity was evaluated with the fALFF method.Receiver operating characteristic(ROC)curve analysis was used to classify the data.Further,we used Pearson’s correlation analysis to explore the relationship between fALFF values in specific brain regions and clinical behaviors in patients with HR.RESULTS:The brain areas of the HR group with lower fALFF values than HCs were the right orbital part of the middle frontal gyrus(RO-MFG)and right lingual gyrus.In contrast,the values of fALFFs in the left middle temporal gyrus(MTG),left superior temporal pole(STP),left middle frontal gyrus(MFG),left superior marginal gyrus(SMG),left superior parietal lobule(SPL),and right supplementary motor area(SMA)were higher in the HR group.The results of a t-test showed that the average values of fALFFs were statistically significantly different in the HR group and HC group(P<0.001).The fALFF values of the left middle frontal gyrus in HR patients were positively correlated with anxiety scores(r=0.9232;P<0.0001)and depression scores(r=0.9682;P<0.0001).CONCLUSION:fALFF values in multiple brain regions of HR patients are abnormal,suggesting that these brain regions in HR patients may be dysfunctional,which may help to reveal the pathophysiological mechanisms of HR.

The Impact of Model Based Offset Scaling Technique on the Amplitude Variation with Offset Responses from 3D Seismic Data Acquired from the Tano Basin, Offshore Ghana

Amplitudes have been found to be a function of incident angle and offset. Hence data required to test for amplitude variation with angle or offset needs to have its amplitudes for all offsets preserved and not stacked. Amplitude Variation with Offset (AVO)/Amplitude Variation with Angle (AVA) is necessary to account for information in the offset/angle parameter (mode converted S-wave and P-wave velocities). Since amplitudes are a function of the converted S- and P-waves, it is important to investigate the dependence of amplitudes on the elastic (P- and S-waves) parameters from the seismic data. By modelling these effects for different reservoir fluids via fluid substitution, various AVO geobody classes present along the well and in the entire seismic cube can be observed. AVO analysis was performed on one test well (Well_1) and 3D pre-stack angle gathers from the Tano Basin. The analysis involves creating a synthetic model to infer the effect of offset scaling techniques on amplitude responses in the Tano basin as compared to the effect of unscaled seismic data. The spectral balance process was performed to match the amplitude spectra of all angle stacks to that of the mid (26°) stack on the test lines. The process had an effect primarily on the far (34° - 40°) stacks. The frequency content of these stacks slightly increased to match that of the near and mid stacks. In offset scaling process, the root mean square (RMS) amplitude comparison between the synthetic and seismic suggests that the amplitude of the far traces should be reduced relative to the nears by up to 16%. However, the exact scaler values depend on the time window considered. This suggests that the amplitude scaling with offset delivered from seismic processing is only approximately correct and needs to be checked with well synthetics and adjusted accordingly prior to use for AVO studies. The AVO attribute volumes generated were better at resolving anomalies on spectrally balanced and offset scaled data than data delivered from conventional processing. A typical class II AVO anomaly is seen along the test well from the cross-plot analysis and AVO attribute cube which indicates an oil filled reservoir.

Salinity effect-induced ENSO amplitude modulation in association with the interdecadal Pacific Oscillation

A 110-year ensemble simulation of an ocean general circulation model(OGCM)was analyzed to identify the modulation of salinity interdecadal variability on El Niño-Southern Oscillation(ENSO)amplitude in the tropical Pacific during 1901-2010.The simulating results show that sea surface salinity(SSS)variation in the region exhibits notable and coherent interdecadal variability signal,which is closely associated with the Interdecadal Pacific Oscillation(IPO).As salinity increases or reduces,the SSS modulations on ENSO amplitude during its warm/cold events vary asymmetrically with positive/negative IPO phases.Physically,salinity interdecadal variability can enhance or reduce ENSO-related conditions in upper-ocean stratification,contributing noticeably to ENSO variability.Salinity anomalies associated with the mixed layer depth and barrier layer thickness can modulate ENSO amplitude during positive and negative IPO phases,resulting in the asymmetry of sea surface temperature(SST)anomaly in the tropical Pacific.During positive IPO phases,SSS interdecadal variability contributes positively to El Niño amplitude but negatively to La Niña amplitude by enhancing or reducing SSS interannual variability,and vice versa during negative IPO phases.Quantitatively,the results indicate that the modulation of the ENSO amplitude by the SSS interdecadal variability is 15%-28%during negative IPO phases and 30%-20%during positive IPO phases,respectively.Evidently,the SSS interdecadal variability associated with IPO and its modulation on ENSO amplitude in the tropical Pacific are among factors essentially contributing ENSO diversity.

O(logN) Algorithm for Amplitude Amplification and O(logN) Algorithms for Amplitude Transfer in Grover’s Algorithm

Grovers algorithm is a category of quantum algorithms that can be applied to many problems through the exploitation of quantum parallelism. The Amplitude Amplification in Grovers algorithm is T = O(N). This paper introduces two new algorithms for Amplitude Amplification in Grovers algorithm with a time complexity of T = O(logN), aiming to improve efficiency in quantum computing. The difference between Grovers algorithm and our first algorithm is that the Amplitude Amplification ratio in Grovers algorithm is an arithmetic series and ours, a geometric one. Because our Amplitude Amplification ratios converge much faster, the time complexity is improved significantly. In our second algorithm, we introduced a new concept, Amplitude Transfer where the marked state is transferred to a new set of qubits such that the new qubit state is an eigenstate of measurable variables. When the new qubit quantum state is measured, with high probability, the correct solution will be obtained.

Atlantic blocking events in a simplified nonlinear baroclinic model for local finite-amplitude wave activity

为研究北大西洋阻高的形成机制,本文在局部有限振幅波活动(LWA)框架下进行了一系列数值实验.采用的数值模型能显式地描绘出两种重要的大气内部动力过程,即非线性纬向位涡通量和Rossby波包传播.模拟结果显示,这两种动力学过程均是形成大西洋阻高的重要机理.具体地,非线性纬向位涡通量和Rossby波包传播,分别是大西洋阻高南部和北部LWA形成的主导因子.因此,本研究综合了前人关于大西洋阻高的研究成果,为其形成机理提供了新的认识.

Trend in seasonal amplitude of northern net ecosystem production:Simulated results from IAP DGVM in CAS-ESM2

北方陆地净生态系统生产力(NEP)具有明显的季节变化特征,这是大气CO_(2)季节变化的关键驱动.研究这些碳循环过程并理解潜在的驱动因素是气候研究的一个关键问题.本文利用第二代中国科学院地球系统模式(CAS-ESM2)中的全球植被动态模型(IAPDGVM),研究了1990-2014年北方NEP(40°-90°N)的季节振幅及其变化趋势.在初始化试验的基础上,本文开展了一个控制试验来评估模拟的北方NEP季节幅度的变化趋势,同时开展了三个敏感性试验来研究气候和大气CO_(2)的贡献.结果表明:1990-2014年,模拟的北方NEP季节振幅显著增加,趋势为9.69万吨碳/月/年,这主要是由于最大NEP增加所致.当分别排除CO_(2)施肥效应和气候效应时,上述增加趋势大大减弱.这些显著的减少表明大气CO_(2)和气候变化对北方NEP的季节性振幅有重要影响.尽管模式存在不确定性,但这些结果有利于进一步提升IAPDGVM对陆地碳循环的精确模拟,也为CAS-ESM研究碳-气候相互作用的应用提供了重要参考.

Lensless complex amplitude demodulation based on deep learning in holographic data storage

To increase the storage capacity in holographic data storage(HDS),the information to be stored is encoded into a complex amplitude.Fast and accurate retrieval of amplitude and phase from the reconstructed beam is necessary during data readout in HDS.In this study,we proposed a complex amplitude demodulation method based on deep learning from a single-shot diffraction intensity image and verified it by a non-interferometric lensless experiment demodulating four-level amplitude and four-level phase.By analyzing the correlation between the diffraction intensity features and the amplitude and phase encoding data pages,the inverse problem was decomposed into two backward operators denoted by two convolutional neural networks(CNNs)to demodulate amplitude and phase respectively.The experimental system is simple,stable,and robust,and it only needs a single diffraction image to realize the direct demodulation of both amplitude and phase.To our investigation,this is the first time in HDS that multilevel complex amplitude demodulation is achieved experimentally from one diffraction intensity image without iterations.

An Example of a Bounded Potential q(x) on the Half-Line, for Estimates of A(α) Amplitude

We show an example of a bounded potential on the half-line obtained as the image of an Inverse Transformation Operator of the Bessel singular potential of the Reduced Radial Schr&#246;dinger Equation, and show us the Estimates of the A(α) amplitude.

Physical-mechanical properties of sediments and their correlation with near seafloor seismic amplitude in the Liwan canyon area, northern South China Sea

Before the implementation of offshore oil and gas exploitation,it is essential to understand the various factors that influence the stability of submarine sediments surrounding the project.Considering the factors such as cost and operability,it is not feasible to assess the physical-mechanical properties of sediments covering the entire region by borehole sampling.In this study,the correlation between near seafloor seismic amplitude and the mean shear strength of shallow sediments was explored using seismic and core testing data from the northern continental slope area of the South China Sea.Results showed that the mean water content of sediments in the layer up to 12 m below the seafloor(mbsf)gradually increased with increasing water depth,and the mean shear strength tended to decrease rapidly near the 1000 m depth contour.The near seafloor seismic amplitude could reflect the mean shear strength of sediments in the 12 mbsf layer under seismic frequency of 65 Hz and wave velocity of 1600 m/s.When the mean shear strength was greater than 10 kPa or the water depth was less than 1000 m,there was a significant linear positive correlation between mean shear strength and near seafloor seismic amplitude.Otherwise,there was a significant linear negative correlation between mean shear strength and near seafloor seismic amplitude.On the basis of these correlations,the pattern of shear strength was estimated from near seafloor seismic amplitude and mapped.The mean shear strength of sediments above 12 mbsf gradually decreased with increasing water depth in the continental slope area,whereas little change occurred in the continental shelf and the end of the canyon.Within the canyon area,the mean shear strength of sediments was characterized by larger values in both sides of the canyon walls and smaller values in the canyon bottom,which was consistent with the infinite slope stability theory.The study provides a method for using near seafloor seismic amplitude data to guide sediment sampling design,and presents a continuous dataset of sediment strength for the simulation of regional sediment stability.

Assessment of cyclic deformation and critical stress amplitude of jointed rocks via cyclic triaxial testing

Jointed rock specimens with a natural replicated joint surface oriented at a mean dip angle of 60were prepared,and a series of cyclic triaxial tests was performed at different confining pressures and cyclic deviatoric stress amplitudes.The samples were subjected to 10,000 loading-unloading cycles with a frequency of 8 Hz.At each level of confining pressure,the applied cyclic deviatoric stress amplitude was increased incrementally until excessive deformation of the jointed rock specimen was observed.Analysis of the test results indicated that there existed a critical cyclic deviatoric stress amplitude(i.e.critical dynamic deviatoric stress)beyond which the jointed rock specimens yielded.The measured critical dynamic deviatoric stress was less than the corresponding static deviatoric stress.At cyclic deviatoric stress amplitudes less than the critical dynamic deviatoric stress,minor cumulative residual axial strains were observed,resulting in hysteretic damping.However,for cyclic deviatoric stresses beyond the critical dynamic deviatoric stress,the plastic strains increased promptly,and the resilient moduli degraded rapidly during the initial loading cycles.Cyclic triaxial test results showed that at higher confining pressures,the ultimate residual axial strain attained by the jointed rock specimen decreased,the steadystate dissipated energy density and steady-state damping ratio per load cycle decreased,while steadystate resilient moduli increased.

Application of the extended Fourier amplitude sensitivity testing(FAST)method to inflated,axial stretched,and residually stressed cylinders

This paper is dedicated to applying the Fourier amplitude sensitivity test(FAST)method to the problem of mixed extension and inflation of a circular cylindrical tube in the presence of residual stresses.The metafunctions and the Ishigami function are considered in the sensitivity analysis(SA).The effects of the input variables on the output variables are investigated,and the most important parameters of the system under the applied pressure and axial force such as the axial stretch and the azimuthal stretch are determined.

The influence of sea water velocity variation on seismic traveltimes,ray paths,and amplitude

The main factors affecting seismic exploration is the propagation velocity of seismic waves in the medium. In the past, during marine seismic data processing, the propagation velocity of sea water was generally taken as a constant 1500 m/s. However, for deep water exploration, the sound velocity varies with the season, time, location, water depth, ocean currents, and etc.. It also results in a layered velocity distribution, so there is a difference of seismic traveltime, ray paths, and amplitude, which affect the migration imaging results if sea water propagation velocity is still taken as constant for the propagation wavefield. In this paper, we will start from an empirical equation of seismic wave velocity in seawater with changes of temperature, salinity, and depth, consider the variation of their values, build a seawater velocity model, and quantitatively analyze the impact of seawater velocity variation on seismic traveltime, ray paths, and amplitude in the seawater velocity model.

Amplitude spectrum compensation and phase spectrum correction of seismic data based on the generalized S transform

We propose a method for the compensation and phase correction of the amplitude spectrum based on the generalized S transform. The compensation of the amplitude spectrum within a reliable frequency range of the seismic record is performed in the S domain to restore the amplitude spectrum of reflection. We use spectral simulation methods to fit the time-dependent amplitude spectrum and compensate for the amplitude attenuation owing to absorption. We use phase scanning to select the time-, space-, and frequencydependent phases correction based on the parsimony criterion and eliminate the residual phase effect of the wavelet in the S domain. The method does not directly calculate the Q value; thus, it can be applied to the case of variable Q. The comparison of the theory model and field data verify that the proposed method can recover the amplitude spectrum of the strata reflectivity, while eliminating the effect of the residual phase of the wavelet. Thus, the wavelet approaches the zero-phase wavelet and, the seismic resolution is improved.

Preserved amplitude migration based on the one way wave equation in the angle domain

Traditional pre-stack depth migration can only provide subsurface structural information. However, simple structure information is insufficient for petroleum exploration which also needs amplitude information proportional to reflection coefficients. In recent years, pre-stack depth migration algorithms which preserve amplitudes and based on the one- way wave equation have been developed. Using the method in the shot domain requires a deconvolution imaging condition which produces some instability in areas with complicated structure and dramatic lateral variation in velocity. Depth migration with preserved amplitude based on the angle domain can overcome the instability of the one-way wave migration imaging condition with preserved amplitude. It can also offer provide velocity analysis in the angle domain of common imaging point gathers. In this paper, based on the foundation of the one-way wave continuation operator with preserved amplitude, we realized the preserved amplitude prestack depth migration in the angle domain. Models and real data validate the accuracy of the method.

Analysis of GPS ionospheric scintillation signal amplitude fading characteristics at low latitude

The received satellite signal amplitude is attenuated greatly due to the strong ionospheric scintillation for lowlatitude regions, which causes the GPS tracking loop＇s loss of lock, the positioning errors to increase, and navigation to be interrupted. To solve the above problems, a novel signal processing algorithm is proposed based on the GPS L1 software receiver during strong ionospheric scintillation using the multi-channel intermediate frequency（IF） data sampling system. Tens of thousands of fading events are obtained based on the signal intensity measurement. The amplitude fading characteristics in the lowlatitude region are analyzed,including fading duration, time separation between fades and the numbers of signal intensity fading events. The fading thresholds are set to be 15 and 10 dB, respectively. The main fading time is very short in- 15 dB fading threshold, which generally is less than 20 ms. The main time separation between fades is less than 2 s in a single one-hour period from the time 23： 00 to 24： 00. Therefore, it has the characteristic of a short reacquisition time for the receiver designed to reduce the probability of simultaneous loss of lock for some satellites.Subsequently, the acquisition, tracking and PVT（position,velocity and time） calculations are completed by the customdesigned software receiver. The results show that the impact analysis of ionospheric scintillation on GPS amplitude attenuation in the lowlatitude region is helpful for designing the advanced tracking algorithm and to improve the robustness and accuracy of the GPS receiver.

Amplitude preserved VSP reverse time migration for angle-domain CIGs extraction

An improved method of generating angle-domain common-image gathers（ADCIGs） by VSP reverse time migration（RTM） is introduced in this paper.The formula which is used to compute the receiver wavefield for VSP RTM is modified by adding an amplitude correction term in order to conveniently output amplitude-preserved ADCIGs.Compared with the surface seismic data,VSP data contains much richer wavefields.However,the direct and downgoing waves can bring about serious imaging artifacts in ADCIGs,especially the direct wave.The feasibility and validity of this method is demonstrated by both numerical and real VSP data from western China.Thus,the ADCIGs from this method can provide reliable basic data for VSP migration velocity analysis,VSP AVO/AVA analysis,and inversion.

An amplitude suppression method based on the decibel criterion

To suppress the strong noise in seismic data with wide range of amplitudes, commonly used methods often yield unsatisfactory denoising results owing to inappropriate thresholds and require parametric testing as well as iterations to achieve the anticipated results. To overcome these problems, a data-driven strong amplitude suppression method based on the decibel criterion in the wavelet domain （ISANA） is proposed. The method determines the denoising threshold based on the decibel criterion and statistically analyzes the amplitude index rather than the abnormally high amplitudes. The method distinguishes the frequency band distributions of the valid signals in the time-frequency domain based on the wavelet transformation and then calculates thresholds in selected time windows, eventually achieving frequency-divided noise attenuation for better denoising. Simulations based on theoretical and real-world data verify the adaptability and low dependence of the method on the size of the time window. The method suppresses noise without energy loss in the signals.

A High Phase Accuracy and Low Amplitude Mismatch Quadrature LO Driver

A 1.1 - 1.2GHz CMOS high phase accuracy,low amplitude mismatch quadrature LO driver is presented,which consists of a high frequency amplifier,an integrated poly phase filter, and an I/Q phase and magnitude calibration circuit（PMCC）. The proposed PMCC uses a feed-forward calibration technique. It improves the phase accuracy and reduces the amplitude mismatch with low power consumption. Simulation results show that phase error with PMCC is reduced to about one half and the amplitude mismatch is reduced to about one tenth, when compared to the LO driver without PMCC. Moreover,the calibration circuit also functions as a buffer to drive mixers, thus no additional buffer is needed in this design. The LO driver is implemented in a TSMC 0.25μm CMOS process. Experimental results show that the LO driver achieves high quadrature accuracy （〈2°） and low amplitude mismatch （0. 1%）. It has about 5.25dB gain and dissipates 6mA from the 2.5V power supply. The size of the die area is only 1.0mm×1.0mm.

True-amplitude wavefield separation using staggered-grid interpolation in the wavenumber domain

Wavefield separation of multicomponent seismic data to image subsurface structures can be realized in either the space domain or the wavenumber domain. However, as the particle velocity components used in the wavenumber-domain wavefield separation are not defined at the same grid point with the staggered-grid finite-difference method for elastic wavefield simulation, we propose the wavenumber-domain interpolation method to estimate the required values at the common grid points prior to the wavenumber-domain true-amplitude wavefield separation. Moreover, numerical experiments show that the wavenumber-domain interpolation method has high interpolation accuracy and the trueamplitude wavefield separation method shows good amplitude preservation. The application of the proposed methodology to elastic reverse-time migration can obtain good amplitudepreserved images even in the case of some velocity error.