The Kuqa fold-and-thrust belt exhibits apparent structural variation in the western and eastern zone.Two salt layer act as effective decollements and influence the varied deformation.In this study,detailed seismic int...The Kuqa fold-and-thrust belt exhibits apparent structural variation in the western and eastern zone.Two salt layer act as effective decollements and influence the varied deformation.In this study,detailed seismic interpretations and analog modeling are presented to construct the suprasalt and subsalt structures in the transfer zone of the middle Kuqa and investigate the influence of the two salt layers.The results reveal that the relationship of the two salt layers changes from separated to connected,and then overlapped toward the foreland in the transfer zone.Different structural models are formed in the suprasalt and subsalt units due to the interaction of the two salt layers.The imbricate thrust faults form two broom-like fault systems in the subsalt units.The suprasalt units develop detached folds terminating toward the east in the region near the orogenic belt.Whereas,two offset anticlines with different trends develop at the frontal edge of the lower salt layer and the trailing edge of the upper salt layer,respectively.According to exploration results in this region,the relationship between suprasalt and subsalt structures has an influence on hydrocarbon accumulation.We believe that the connected deformation contains high-risk plays while the decoupled deformation contains well-preserved plays.展开更多
Water–sand flow triggered by rainfall is the dominant mechanism for instability and failure of sand slopes. To further analyze the stability state of sand on a slope under different rainfall conditions, the initiatio...Water–sand flow triggered by rainfall is the dominant mechanism for instability and failure of sand slopes. To further analyze the stability state of sand on a slope under different rainfall conditions, the initiation conditions and flow characteristics of water–sand flows are studied. Based on the theory of equilibrium forces and hydrological dynamics, a 1：100-scale analog model is built and verified with field observation data. The results indicate three dynamic stabilization stages of the sand slope under different weather conditions： dry sand, wet sand, and water–sand flow. Water–sand flows are triggered easilyunder short duration and heavy rainfall conditions. The rainfall threshold required to initiate water–sand flow is 4.14 mm/h. Rainfall amount and duration required to initiate water–sand flow decrease with fine sand content increasing. A sand head that develops at the front of the water–sand flow results in a flow along the edge of the sand debris flow and a ‘‘tree root’’ flow morphology. Modelingresults are consistent with theoretical analysis and field observations.展开更多
There is a close theoretical similarity between water pressure gradients in aquifers and applied voltage gradients in aqueous solutions. A series of electric field analogue experiments has been conducted by focusing ...There is a close theoretical similarity between water pressure gradients in aquifers and applied voltage gradients in aqueous solutions. A series of electric field analogue experiments has been conducted by focusing on symmetrical multi-lateral wells and dual-lateral wells of arbitrary angles between laterals. This research not only evaluates the productivity equations of a symmetrical multi-lateral well showing the effect of angles on productivity, but also proposes the concept of the multi-lateral productivity coefficient. Moreover, the multi-lateral productivity coefficient equation is designed to calculate the productivity of dual-lateral wells of variable angles, which is in turn supported by experiment. It also helps provide the experimental basis for optimizing the configuration, and building the semi-analytic productivity model, of multi-lateral wells.展开更多
Due to inherent limits of data acquisition and geophysical data resolution, there are large uncertainties in the characterization of subsurface fractures. However, outcrop analogies can provide qualitative and quantit...Due to inherent limits of data acquisition and geophysical data resolution, there are large uncertainties in the characterization of subsurface fractures. However, outcrop analogies can provide qualitative and quantitative information on a large number of fractures, based on which the accuracy of subsurface fracture characterization can be improved. Here we take the tectonic fracture modeling of an ultra-low permeability sandstone reservoir based on an outcrop analogy, a case study of the Chang6t~ Formation of the Upper Triassic Yanchang Group of the Wangyao Oilfield in the Ordos Basin of China. An outcrop at the edge of the basin is a suitable analog for the reservoir, but the prerequisite is that they must have equivalent previous stress fields, similar final structural characteristics, relative timing and an identical depositional environment and diagenesis. The relationship among fracture density, rock type and bed thickness based on the outcrop is one of the most important fracture distribution models, and can be used to interpret fracture density in individual wells quantitatively. Fracture orientation, dip, geometry and scale, also should be described and measured in the outcrop, and can be used together with structure restoration and single well fracture density interpretation to guide fracture intensity prediction on bed surfaces and to constrain the construction of the 3D fracture geometry model of the subsurface reservoir. The application of the above principles shows the outcrop-based tectonic fracture models of the target ultra-low permeability sandstone reservoir are consistent with fractures inferred from microseismic interpretation and tracer tests. This illustrated that the fracture modeling based on the outcrop analogy is reliable and can reduce the uncertainty in stochastic fracture modeling.展开更多
交通运输行业碳排放达峰是一项长期的自然演变过程。为研究中国交通运输行业碳达峰进程,本文首先采用国际类比法,选取国外典型国家,对比国家总体碳排放量、交通运输行业碳排放量以及换算周转量三者峰值出现的时间,分析交通运输行业碳排...交通运输行业碳排放达峰是一项长期的自然演变过程。为研究中国交通运输行业碳达峰进程,本文首先采用国际类比法,选取国外典型国家,对比国家总体碳排放量、交通运输行业碳排放量以及换算周转量三者峰值出现的时间,分析交通运输行业碳排放的自然达峰特征,结合交通需求预测,预判中国交通运输行业碳排放自然达峰时间。然后,引入单位换算周转量碳排放量、铁路公路货运比等核心影响因素,构建交通运输碳排放STIRPAT(Stochastic Impacts by Regression on Population, Affluence, and Technology)预测模型。最后,通过类比分析与模型预测,得到中国交通运输行业碳达峰时间及峰值排放量。国际类比结果表明:交通运输行业碳达峰与国家碳达峰之间没有明确的因果关系,但与换算周转量达峰紧密相关,交通运输行业碳排放达峰时换算周转量达峰或接近峰值;预测中国换算周转量在2048年左右达到26万亿吨公里的平台期,从国际类比的角度判断,中国交通运输行业实现碳排放自然达峰时间约在2040—2043年。STIRPAT模型显示:城镇化率、人均GDP、单位换算周转量碳排放量、铁路公路货运比每增加1%,中国交通运输行业碳排放量将分别增加1.201%、0.259%、0.454%、-0.389%。基于国际类比与STIRPAT模型组合预测判断,中国交通运输行业将在2038—2040年实现碳排放达峰,峰值排放量约为13亿t。展开更多
模数转换器(Analog-to-Digital Converter,ADC)是连接模拟信号域与数字信号域的关键器件,而现有研究缺乏ADC辐照效应建模的相关内容.为满足大型模数混合信号系统辐照效应建模仿真的需要,本文提出了建立具有辐照效应的ADC行为级模型的方...模数转换器(Analog-to-Digital Converter,ADC)是连接模拟信号域与数字信号域的关键器件,而现有研究缺乏ADC辐照效应建模的相关内容.为满足大型模数混合信号系统辐照效应建模仿真的需要,本文提出了建立具有辐照效应的ADC行为级模型的方法.首先根据ADC的工作原理将其拆解为不同的通用模块,使用模拟和混合信号硬件描述语言(Very High speed integrated circuit hardware Description Language for Analog and Mixed Signals,VHDL-AMS)建立了各模块的行为级模型.接着根据基本原理将各模块动态组合为未辐照情况下基本的ADC模型.对于ADC的辐照效应,通过开展辐照试验,测量了ADC芯片HWD7710和SAD9434受总剂量(Total Ionizing Dose,TID)效应和中子辐射(Neutron Radiation,NR)效应影响的工作参数,并利用最小二乘法拟合获得ADC的工作参数与辐照剂量的关系式.最后根据辐照关系式,在基本模型上添加辐照参数模块,并建立两种不同结构ADC的TID与NR模型.通过仿真结果与试验数据对比,验证了所建ADC辐射效应模型的普适性和精度.模型的静态参数仿真结果与试验结果的相对偏差在5%以内,证明该方法支持对不同ADC及不同辐射效应进行辐照效应模型建模.展开更多
基金supported by the National Natural Science Foundation of China(Grant Nos.41572187,41972219,41927802 and 42072320)the China Postdoctoral Science Foundation(Grant No.2020M671432)。
文摘The Kuqa fold-and-thrust belt exhibits apparent structural variation in the western and eastern zone.Two salt layer act as effective decollements and influence the varied deformation.In this study,detailed seismic interpretations and analog modeling are presented to construct the suprasalt and subsalt structures in the transfer zone of the middle Kuqa and investigate the influence of the two salt layers.The results reveal that the relationship of the two salt layers changes from separated to connected,and then overlapped toward the foreland in the transfer zone.Different structural models are formed in the suprasalt and subsalt units due to the interaction of the two salt layers.The imbricate thrust faults form two broom-like fault systems in the subsalt units.The suprasalt units develop detached folds terminating toward the east in the region near the orogenic belt.Whereas,two offset anticlines with different trends develop at the frontal edge of the lower salt layer and the trailing edge of the upper salt layer,respectively.According to exploration results in this region,the relationship between suprasalt and subsalt structures has an influence on hydrocarbon accumulation.We believe that the connected deformation contains high-risk plays while the decoupled deformation contains well-preserved plays.
基金supported by the National Natural Science Foundation of China (NSFC) (Grants Nos. 41662020 and 41462012)
文摘Water–sand flow triggered by rainfall is the dominant mechanism for instability and failure of sand slopes. To further analyze the stability state of sand on a slope under different rainfall conditions, the initiation conditions and flow characteristics of water–sand flows are studied. Based on the theory of equilibrium forces and hydrological dynamics, a 1：100-scale analog model is built and verified with field observation data. The results indicate three dynamic stabilization stages of the sand slope under different weather conditions： dry sand, wet sand, and water–sand flow. Water–sand flows are triggered easilyunder short duration and heavy rainfall conditions. The rainfall threshold required to initiate water–sand flow is 4.14 mm/h. Rainfall amount and duration required to initiate water–sand flow decrease with fine sand content increasing. A sand head that develops at the front of the water–sand flow results in a flow along the edge of the sand debris flow and a ‘‘tree root’’ flow morphology. Modelingresults are consistent with theoretical analysis and field observations.
文摘There is a close theoretical similarity between water pressure gradients in aquifers and applied voltage gradients in aqueous solutions. A series of electric field analogue experiments has been conducted by focusing on symmetrical multi-lateral wells and dual-lateral wells of arbitrary angles between laterals. This research not only evaluates the productivity equations of a symmetrical multi-lateral well showing the effect of angles on productivity, but also proposes the concept of the multi-lateral productivity coefficient. Moreover, the multi-lateral productivity coefficient equation is designed to calculate the productivity of dual-lateral wells of variable angles, which is in turn supported by experiment. It also helps provide the experimental basis for optimizing the configuration, and building the semi-analytic productivity model, of multi-lateral wells.
基金supported by Open Fund (PLC201203) of State Key Laboratory of Oil and Gas Reservoir Geology and Exploitation (Chengdu University of Technology)Major Project of Education Department in Sichuan Province (13ZA0177)
文摘Due to inherent limits of data acquisition and geophysical data resolution, there are large uncertainties in the characterization of subsurface fractures. However, outcrop analogies can provide qualitative and quantitative information on a large number of fractures, based on which the accuracy of subsurface fracture characterization can be improved. Here we take the tectonic fracture modeling of an ultra-low permeability sandstone reservoir based on an outcrop analogy, a case study of the Chang6t~ Formation of the Upper Triassic Yanchang Group of the Wangyao Oilfield in the Ordos Basin of China. An outcrop at the edge of the basin is a suitable analog for the reservoir, but the prerequisite is that they must have equivalent previous stress fields, similar final structural characteristics, relative timing and an identical depositional environment and diagenesis. The relationship among fracture density, rock type and bed thickness based on the outcrop is one of the most important fracture distribution models, and can be used to interpret fracture density in individual wells quantitatively. Fracture orientation, dip, geometry and scale, also should be described and measured in the outcrop, and can be used together with structure restoration and single well fracture density interpretation to guide fracture intensity prediction on bed surfaces and to constrain the construction of the 3D fracture geometry model of the subsurface reservoir. The application of the above principles shows the outcrop-based tectonic fracture models of the target ultra-low permeability sandstone reservoir are consistent with fractures inferred from microseismic interpretation and tracer tests. This illustrated that the fracture modeling based on the outcrop analogy is reliable and can reduce the uncertainty in stochastic fracture modeling.
文摘交通运输行业碳排放达峰是一项长期的自然演变过程。为研究中国交通运输行业碳达峰进程,本文首先采用国际类比法,选取国外典型国家,对比国家总体碳排放量、交通运输行业碳排放量以及换算周转量三者峰值出现的时间,分析交通运输行业碳排放的自然达峰特征,结合交通需求预测,预判中国交通运输行业碳排放自然达峰时间。然后,引入单位换算周转量碳排放量、铁路公路货运比等核心影响因素,构建交通运输碳排放STIRPAT(Stochastic Impacts by Regression on Population, Affluence, and Technology)预测模型。最后,通过类比分析与模型预测,得到中国交通运输行业碳达峰时间及峰值排放量。国际类比结果表明:交通运输行业碳达峰与国家碳达峰之间没有明确的因果关系,但与换算周转量达峰紧密相关,交通运输行业碳排放达峰时换算周转量达峰或接近峰值;预测中国换算周转量在2048年左右达到26万亿吨公里的平台期,从国际类比的角度判断,中国交通运输行业实现碳排放自然达峰时间约在2040—2043年。STIRPAT模型显示:城镇化率、人均GDP、单位换算周转量碳排放量、铁路公路货运比每增加1%,中国交通运输行业碳排放量将分别增加1.201%、0.259%、0.454%、-0.389%。基于国际类比与STIRPAT模型组合预测判断,中国交通运输行业将在2038—2040年实现碳排放达峰,峰值排放量约为13亿t。
文摘模数转换器(Analog-to-Digital Converter,ADC)是连接模拟信号域与数字信号域的关键器件,而现有研究缺乏ADC辐照效应建模的相关内容.为满足大型模数混合信号系统辐照效应建模仿真的需要,本文提出了建立具有辐照效应的ADC行为级模型的方法.首先根据ADC的工作原理将其拆解为不同的通用模块,使用模拟和混合信号硬件描述语言(Very High speed integrated circuit hardware Description Language for Analog and Mixed Signals,VHDL-AMS)建立了各模块的行为级模型.接着根据基本原理将各模块动态组合为未辐照情况下基本的ADC模型.对于ADC的辐照效应,通过开展辐照试验,测量了ADC芯片HWD7710和SAD9434受总剂量(Total Ionizing Dose,TID)效应和中子辐射(Neutron Radiation,NR)效应影响的工作参数,并利用最小二乘法拟合获得ADC的工作参数与辐照剂量的关系式.最后根据辐照关系式,在基本模型上添加辐照参数模块,并建立两种不同结构ADC的TID与NR模型.通过仿真结果与试验数据对比,验证了所建ADC辐射效应模型的普适性和精度.模型的静态参数仿真结果与试验结果的相对偏差在5%以内,证明该方法支持对不同ADC及不同辐射效应进行辐照效应模型建模.
