Analytical model for predicting time-dependent lateral deformation of geosynthetics-reinforced soil walls with modular block facing

To date,few models are available in the literature to consider the creep behavior of geosynthetics when predicting the lateral deformation(d)of geosynthetics-reinforced soil(GRS)retaining walls.In this study,a general hyperbolic creep model was first introduced to describe the long-term deformation of geosynthetics,which is a function of elapsed time and two empirical parameters a and b.The conventional creep tests with three different tensile loads(Pr)were conducted on two uniaxial geogrids to determine their creep behavior,as well as the a-Pr and b-Pr relationships.The test results show that increasing Pr accelerates the development of creep deformation for both geogrids.Meanwhile,a and b respectively show exponential and negatively linear relationships with Pr,which were confirmed by abundant experimental data available in other studies.Based on the above creep model and relationships,an accurate and reliable analytical model was then proposed for predicting the time-dependent d of GRS walls with modular block facing,which was further validated using a relevant numerical investigation from the previous literature.Performance evaluation and comparison of the proposed model with six available prediction models were performed.Then a parametric study was carried out to evaluate the effects of wall height,vertical spacing of geogrids,unit weight and internal friction angle of backfills,and factor of safety against pullout on d at the end of construction and 5 years afterwards.The findings show that the creep effect not only promotes d but also raises the elevation of the maximum d along the wall height.Finally,the limitations and application prospects of the proposed model were discussed and analyzed.

Analytical Modeling and Mechanism Analysis of Time-Varying Excitation for Surface Defects in Rolling Element Bearings

Surface defects,including dents,spalls,and cracks,for rolling element bearings are the most common faults in rotating machinery.The accurate model for the time-varying excitation is the basis for the vibration mechanism analysis and fault feature extraction.However,in conventional investigations,this issue is not well and fully addressed from the perspective of theoretical analysis and physical derivation.In this study,an improved analytical model for time-varying displacement excitations(TVDEs)caused by surface defects is theoretically formulated.First and foremost,the physical mechanism for the effect of defect sizes on the physical process of rolling element-defect interaction is revealed.According to the physical interaction mechanism between the rolling element and different types of defects,the relationship between time-varying displacement pulse and defect sizes is further analytically derived.With the obtained time-varying displacement pulse,the dynamic model for the deep groove bearings considering the internal excitation caused by the surface defect is established.The nonlinear vibration responses and fault features induced by surface defects are analyzed using the proposed TVDE model.The results suggest that the presence of surface defects may result in the occurrence of the dual-impulse phenomenon,which can serve as indexes for surface-defect fault diagnosis.

Analytical model of 2D leakoff in waterflood-induced fractures

Waterflood-induced fractures,also known as self-induced fractures,spontaneously form at injection wells during waterflooding.These fractures propagate long distances through rock,allowing injected fluids to travel far away from a well,both within and outside the flooding layer.Essentially,the me-chanics of waterflood-induced fracture propagation is similar to that of hydraulic fractures,which are intentionally created for reservoir stimulation.Fracturing models developed for hydraulic fractures can also be applied to waterflood-induced fractures.However,waterflood-induced fractures are typically pumped with much larger volumes of water or brine and grow much longer in time.As a result,fluid leakoff from waterflood fractures into the formation is more extensive and two-dimensional(2D),a characteristic that is often ignored in a majority of modern fracturing simulators,making their appli-cation to waterflood fractures unreliable.In this work,we revisit the problem of leakoff for long-growing waterflood-induced fractures and develop a new analytical model for fluid leakoff that provides improved predictions of fracture geometry and can be easily implemented in fracturing simulators.We incorporate the developed solution into the classical Perkins-Kern-Nordgren(PKN)model of fracture growth,which shows that the choice of the Carter or a 2D leakoff model greatly impacts fracture ge-ometry at large time.The conducted parametric study shows while a toughness-dominated regime af-fects fracture evolution,most of fracture lifetime occurs in a viscosity-and-leakoff-dominated regime.We also develop an asymptotic solution for a leakoff profile in the limiting case of 2D leakoff domination(~~M and~~K).Finally,we study 3D fracture growth and out-of-zone injection with three layers and a complex structure of zones.The study shows that ignoring the 2D leakoff during simulation results in a significant overestimation of fracture geometry predictions.The present work,thus,plays an important role in improving waterflood fracture modelling,as it highlights the significance of 2D leakoff in waterflood-induced fractures and provides a reliable analytical model for fluid leakoff that can be incorporated into modern fracture simulators.

Three-Dimensional Analytical Modeling of Axial-Flux Permanent Magnet Drivers

In this paper, the axial-flux permanent magnet driver is modeledand analyzed in a simple and novel way under three-dimensional cylindricalcoordinates. The inherent three-dimensional characteristics of the deviceare comprehensively considered, and the governing equations are solved bysimplifying the boundary conditions. The axial magnetization of the sectorshapedpermanent magnets is accurately described in an algebraic form bythe parameters, which makes the physical meaning more explicit than thepurely mathematical expression in general series forms. The parameters of theBessel function are determined simply and the magnetic field distribution ofpermanent magnets and the air-gap is solved. Furthermore, the field solutionsare completely analytical, which provides convenience and satisfactoryaccuracy for modeling a series of electromagnetic performance parameters,such as the axial electromagnetic force density, axial electromagnetic force,and electromagnetic torque. The correctness and accuracy of the analyticalmodels are fully verified by three-dimensional finite element simulations and a15 kW prototype and the results of calculations, simulations, and experimentsunder three methods are highly consistent. The influence of several designparameters on magnetic field distribution and performance is studied and discussed.The results indicate that the modeling method proposed in this papercan calculate the magnetic field distribution and performance accurately andrapidly, which affords an important reference for the design and optimizationof axial-flux permanent magnet drivers.

A new analytical model for thermal stresses in multi-phase materials and lifetime prediction methods

Based on the fundamental equations of the mechanics of solid continuum, the paper employs an analytical model for determination of elastic thermal stresses in isotropic continuum represented by periodically distributed spherical particles with different distributions in an infinite matrix, imaginarily divided into identical cells with dimensions equal to inter-particle distances, containing a central spherical particle with or without a spherical envelope on the particle surface. Consequently, the multi-particle-（envelope）- matrix system, as a model system regarding the analytical modelling, is applicable to four types of multi-phase materials. As functions of the particle volume fraction v, the inter-particle distances dl, d2, d3 along three mutually per- pendicular axes, and the particle and envelope radii, R1 and R2, respectively, the thermal stresses within the cell, are originated during a cooling process as a consequence of the difference in thermal expansion coefficients of phases rep- resented by the matrix, envelope and particle. Analytical-（experimental）-computational lifetime prediction methods for multi-phase materials are proposed, which can be used in engineering with appropriate values of parameters of real multi-phase materials.

Simple analytical model for depth-averaged velocity in meandering compound channels

A simple but applicable analytical model is presented to predict the lat- eral distribution of the depth-averaged velocity in meandering compound channels. The governing equation with curvilinear coordinates is derived from the momentum equation and the flow continuity equation under the condition of quasi-uniform flow. A series of experiments are conducted in a large-scale meandering compound channel. Based on the experimental data, a magnitude analysis is carried out for the governing equation, and two lower-order shear stress terms are ignored. Four groups of experimental data from different sources are used to verify the predictive capability of this model, and good predictions are obtained. Finally, the determination of the velocity parameter and the limitation of this model are discussed.

Analytical Model of Elastic Modulus and Coefficient of Thermal Expansion for 2.5D C/SiC Composite

To make better use of 2.5D C/SiC composites in industry, it is necessary to understand the mechanical properties. A finite element model＇of 2.5D composites is established, by considering the fiber undulation and the porosity in 2.5D C/SiC composites. The fiber direction of warp is defined by cosine function to simulate the undulation of warp, and based on uniform strain assumption, analytical model of the elastic modulus and coefficient of thermal expansion （CTE） for 2.5D C/SiC composites were established by using dual- scale model. The result is found to correlate reasonably well with the predicted results and experimental results. The parametric study also demonstrates the effects of the fiber volume fraction, distance of warp yarn, and porosity in micro-scale on the mechanical properties and the coefficients of thermal expansion.

Analytical model of tilted driver–pickup coils for eddy current nondestructive evaluation

A driver-pickup probe possesses better sensitivity and flexibility due to individual optimization of a coil. It is fre- quently observed in an eddy current （EC） array probe. In this work, a tilted non-coaxial driver-pickup probe above a multilayered conducting plate is analytically modeled with spatial transformation for eddy current nondestructive evalua- tion. Basically, the core of the formulation is to obtain the projection of magnetic vector potential （MVP） from the driver coil onto the vector along the tilted pickup coil, which is divided into two key steps. The first step is to make a projection of MVP along the pickup coil onto a horizontal plane, and the second one is to build the relationship between the pr, ojected MVP and the MVP along the driver coil. Afterwards, an analytical model for the case of a layered plate is established with the reflection and transmission theory of electromagnetic fields. The calculated values from the resulting model indicate good agreement with those from the finite element model （FEM） and experiments, which validates the developed analytical model.

Analytical modeling of sandwich beam for piezoelectric bender elements

Piezoelectric bender elements are widely used as electromechanical sensors and actuators, An analytical sandwich beam model for piezoelectric bender elements was developed based on the first-order shear deformation theory （FSDT）, which assumes a single rotation angle for the whole cross-section and a quadratic distribution function for coupled electric potential in piezoelectric layers, and corrects the effect of transverse shear strain on the electric displacement integration. Free vibration analysis of simplysupported bender elements was carried out and the numerical results showed that, solutions of the present model for various thickness-to-length ratios are compared well with the exact two-dimensional solutions, which presents an efficient and accurate model for analyzing dynamic electromechanical responses of bender elements.

Analytical Model for the Palaeoenvironmental Evolution of the Nihewan Beds

In this paper, the evolutional characteristics of palaeoclimate and oxidation-reduction conditions as well asacidity-alkalinity environment are discussed by means of the step-regression, cluster, optimal partitioning andcorrelation analyses of CaCO_3, C / P_2O_5, Fe^(2+) / Fe^(3+), pH and Eh values, taking the Xiaodukou section in theNihewan basin as an example. The CaCO_3, C / P_2O_5 and pH were calculated respectively using the optimalpartitioning method. Thus five cold zones and six warm zones as well as five reduction and six oxidation zoneswere distinguished. Then the inductive method was used to produce four numerical groups: 8.10, 8.3-8.4,8.6-8.7 and 8.9-8,97. The above-mentioned results are respectively based on CaCO_3 content, C/P_2O_5 andpH values. From Fig. 3, Tables 1 and 2 it can be seen that the Nihewan Beds were formed mainly under a re-duction and slightly alkaline environment of cold climate, with pH values of 8.3-8.4. Fig. 3 shows that bed 35is approximately near the boundary between the Brunhes and Matuyama polarity epochs, 0.73 Ma in age; bed26 is roughly near the Jaramillo event (base), 0.97 Ma in age; bed 18 coincides roughly with themagnetostratigraphic boundary of 2.00 Ma (?). Bed 13 may be the Pleistocene-Pliocene boundary, 2.48 Ma inage. Thus geochemical zones Ⅰ, Ⅱ, Ⅲ and Ⅳ include respectively cold zones 1; 2 and 3; 4; and 5.

Analytical modelling of the mechanical damage of soil induced by lightning strikes capturing electro-thermal,thermo-osmotic,and electro-osmotic effects

This article presents a mathematical model for simulating the mechanical behaviour of lightning strikes and analysing the resulting damage to the soil.This article focuses on the electro-thermal effect and seepage caused by lightning strikes in particular.Then,a numerical model based on the conservation laws of momentum,mass and energy is developed for soil subjected to lightning strikes.Comparisons to field observations and theoretical calculations are used to demonstrate the efficacy and accuracy of numerical simulations.The findings demonstrate that lightning strikes can cause soils to experience both seepage force and heat stress.Under the calculative condition of this article:by increasing the intrinsic permeability of the soil,k_(p)(≥10^(-10)m^(2)),the seepage force can be effectively reduced,hence reducing the risk of lightning strikes;improving the electrical conductivity of the soil β(≥10^(-1) S/m^(2))and lowering its thermal expansion coefficient(≤10^(-6)K^(-1))can greatly reduce the damage caused by lightning strikes to the soil.The preceding investigations demonstrate that the suggested model is capable of evaluating mechanical damage caused by lightning in the soil,and the findings contribute to a better understanding of soil mechanical response to lightning strikes.

A quantum efficiency analytical model for complementary metal–oxide–semiconductor image pixels with a pinned photodiode structure

A quantum efficiency analytical model for complementary metal–oxide–semiconductor（CMOS） image pixels with a pinned photodiode structure is developed. The proposed model takes account of the non-uniform doping distribution in the N-type region due to the impurity compensation formed by the actual fabricating process. The characteristics of two boundary PN junctions located in the N-type region for the particular spectral response of a pinned photodiode, are quantitatively analyzed. By solving the minority carrier steady-state diffusion equations and the barrier region photocurrent density equations successively, the analytical relationship between the quantum efficiency and the corresponding parameters such as incident wavelength, N-type width, peak doping concentration, and impurity density gradient of the N-type region is established. The validity of the model is verified by the measurement results with a test chip of 160×160 pixels array,which provides the accurate process with a theoretical guidance for quantum efficiency design in pinned photodiode pixels.

Analytical Modelling and Experiment of Novel Rotary Electro-Mechanical Converter with Negative Feedback Mechanism for 2D Valve

The manufacturing of spiral groove structure of two-dimensional valve(2D valve)feedback mechanism has shortcomings of both high cost and time-consuming.This paper presents a novel configuration of rotary electro-mechanical converter with negative feedback mechanism(REMC-NFM)in order to replace the feedback mechanism of spiral groove and thus reduce cost of valve manufacturing.In order to rapidly and quantitative evaluate the driving and feedback performance of the REMC-NFM,an analytical model taking leakage flux,edge effect and permeability nonlinearity into account is formulated based on the equivalent magnetic circuit approach.Then the model is properly simplified in order to obtain the optimal pitch angle.FEM simulation is used to study the influence of crucial parameters on the performance of REMC-NFM.A prototype of REMC-NFM is designed and machined,and an exclusive experimental platform is built.The torque-angle characteristics,torque-displacement characteristics,and magnetic flux density in the working air gap with different excitation currents are measured.The experimental results are in good agreement with the analytical and FEM simulated results,which verifies the correctness of the analytical model.For torque-angle characteristics,the overall torque increases with both current and rotation angle,which reaches about 0.48 N·m with 1.5 A and 1.5°.While for torque-displacement characteristics,the overall torque increases with current yet decrease with armature displacement due to the negative feedback mechanism,which is about 0.16 N·m with 1.5 A and 0.8 mm.Besides,experimental results of conventional torque motor are compared with counterparts of REMC-NFM in order to validate the simplified model.The research indicates that the REMC-NFM can be potentially used as the electro-mechanical converter for 2D valves in civil servo areas.

A simple analytical model of laser direct-drive thin shell target implosion

A high-neutron yield platform imploded by a thin shell target is generally built to probe nuclear science problems,and it has the advantages of high neutron yield,ultrashort fusion time,micro fusion zone,isotropic and monoenergetic neutron.Some analytical models have been proposed to interpret exploding-pusher target implosion driven by a long wavelength laser,whereas they are imperfect for a 0.35 μm laser implosion experiment.When using the 0.35 μm laser,the shell is ablated and accelerated to high implosion velocity governed by Newton’s law,ablation acceleration and quasi-adiabatic compression models are suitable to explain the implosion of a laser direct-drive thin shell target.The new analytical model scales bang time,ion temperature and neutron yield for large variations in laser power,target radius,shell thickness,and fuel pressure.The predicted results of the analytical model are in agreement with experimental data on the ShenguangIII prototype laser facility,100 kJ laser facility,Omega,and NIF,it demonstrates that the analytical model benefits the understanding of experiment performance and optimizing the target design of high neutron yield implosion.

A two-dimensional fully analytical model with polarization effect for off-state channel potential and electric field distributions of GaN-based field-plated high electron mobility transistor

In this paper, we present a two-dimensional （2D） fully analytical model with consideration of polarization effect for the channel potential and electric field distributions of the gate field-plated high electron mobility transistor （FP-HEMT） on the basis of 2D Poisson＇s solution. The dependences of the channel potential and electric field distributions on drain bias, polarization charge density, FP structure parameters, A1GaN/GaN material parameters, etc. are investigated. A simple and convenient approach to designing high breakdown voltage FP-HEMTs is also proposed. The validity of this model is demonstrated by comparison with the numerical simulations with Silvaco-Atlas. The method in this paper can be extended to the development of other analytical models for different device structures, such as MIS-HEMTs, multiple-FP HETMs, slant-FP HEMTs, etc.

Analytical Model for Underwater Wireless Sensor Network Energy Consumption Reduction

In an Underwater Wireless Sensor Network(UWSN),extreme energy loss is carried out by the early expiration of sensor nodes and causes a reduction in efficiency in the submerged acoustic sensor system.Systems based on clustering strategies,instead of each node sending information by itself,utilize cluster heads to collect information inside the clusters for forwarding collective information to sink.This can effectively minimize the total energy loss during transmission.The environment of UWSN is 3D architecture-based and follows a complex hierarchical clustering strategy involving its most effecting unique parameters such as propagation delay and limited transmission bandwidth.Round base clustering strategy works in rounds,where each round comprises three fundamental stages:cluster head selection,grouping or node association,and data aggregation followed by forwarding data to the sink.In UWSN,the energy consumed during the formation of clusters has been considered casually or completely evaded in the previous works.In this paper,the cluster head setup period has been considered the main contributor to extra energy utilizer.A numerical channel model is proposed to compute extra energy.It is performed by using a UWSN broad model.The results have shown that extra maximum energy consumption is approximately 12.9 percent of the system total energy consumed in information transmissions.

Analytical modeling and vibration analysis of fiber reinforced composite hexagon honeycomb sandwich cylindrical-spherical combined shells

This study analyzes and predicts the vibration characteristics of fiberreinforced composite sandwich(FRCS)cylindrical-spherical(CS)combined shells with hexagon honeycomb core(HHC)for the first time based on an analytical model developed,which makes good use of the advantage of the first-order shear deformation theory(FSDT),the multi-segment decomposition technique,the virtual spring technology,the Jacobi-Ritz approach,and the transfer function method.The equivalent material properties of HHC are firstly determined by the modified Gibson’s formula,and the related energy equations are derived for the HHC-FRCS-CS combined shells,from which the fundamental frequencies,the mode shapes,and the forced vibration responses are solved.The current model is verified through the discussion of convergence and comparative analysis with the associated published literature and finite element(FE)results.The effects of geometric parameters of HHC on the dynamic property of the structure are further investigated with the verified model.It reveals that the vibration suppression capability can be greatly enhanced by reducing the ratio of HHC thickness to total thickness and the ratio of wall thickness of honeycomb cell to overall radius,and by increasing the ratio of length of honeycomb cell to overall radius and honeycomb characteristic angle of HHC.

ANALYTICAL MODEL OF CERAMIC/METAL ARMOR IMPACTED BY DEFORMABLE PROJECTILE

A new analytical model was established to describe the complex behavior of ceramic/metal armor under impact of deformable projectile by assuming some hypotheses. Three aspects were taken into account： the mushrooming deformation of the projectile, the fragment of ceramic tile and the formation and change of ceramic conoid and the deformation of the metal backup plate. Solving the set of equations, all the variables were obtained for the different impact velocities： the extent and particle velocity in rigid zone; the extent, cross-section area and particle velocity in plastic zone; the velocity and depth of penetration of projectile to the target; the reduction in volume and compressive strength of the fractured ceramic conoid; the displacement and movement velocity of the effective zone of backup plate. Agreement observed among analytical result, numerical simulation and experimental result confirms the validity of the model, suggesting the model developed can be a useful tool for ceramic/metal armor design.

Analytical model including the fringing-induced barrier lowering effect for a dual-material surrounding-gate MOSFET with a high-κ gate dielectric

By solving Poisson＇s equation in both semiconductor and gate insulator regions in the cylindrical coordinates, an analytical model for a dual-material surrounding-gate （DMSG） metal-oxide semiconductor field-effect transistor （MOSFET） with a high-k gate dielectric has been developed. Using the derived model, the influences of fringing-induced barrier lowering （FIBL） on surface potential, subthreshold current, DIBL, and subthreshold swing are investigated. It is found that for the same equivalent oxide thickness, the gate insulator with high-k dielectric degrades the short-channel performance of the DMSG MOSFET. The accuracy of the analytical model is verified by the good agreement of its results with that obtained from the ISE three-dimensional numerical device simulator.

Analytical Modeling for Translating Statistical Changes to Circuit Variability by Ultra⁃Deep Submicron Digital Circuit Design

This paper presents a physics⁃based compact gate delay model that includes all short⁃channel phenomena prevalent at the ultra⁃deep submicron technology node of 32 nm.To simplify calculations,the proposed model is connected to a compactα⁃power law⁃based(Sakurai⁃Newton)model.The model has been tested on a wide range of supply voltages.The model accurately predicts nominal delays and the delays under process variations.It has been shown that at lower technology nodes,the delay is more sensitive to threshold voltage variations,specifically at the sub⁃threshold operating region as compared with effective channel length variations above the threshold region.