Determination of the grouting anchor pullout force is a key step during the design of anchor-pull retaining wall, but it is mostly determined relied on empirical formula at present, and the rationality and the safety ...Determination of the grouting anchor pullout force is a key step during the design of anchor-pull retaining wall, but it is mostly determined relied on empirical formula at present, and the rationality and the safety cannot be effectively guaranteed. Based on the engineering case of the gravity retaining wall of Qinglin Freeway, the model test was designed, and combined with the results of the ABAQUS finite element numerical analysis, it was analyzed that how the anchor axial pulling force distributes. The results showed that the force of the anchor near the wall bolt was large and which far from the wall was small and the ultimate pullout force was proportional to the length, diameter and shear strength. When the end tension of the anchor was small, the top load played a leading role on the anchor tension. This conclusion confirmed the calculation formula of ultimate pullout force was and provided a theoretical basis for anchor-pull retaining wall design and calculation.展开更多
Experimental and numerical investigations have been carried out on behavior of pullout resistance of embedded circular plate with and without geogrid reinforcement layers in stabilized loose and dense sands using a gr...Experimental and numerical investigations have been carried out on behavior of pullout resistance of embedded circular plate with and without geogrid reinforcement layers in stabilized loose and dense sands using a granular trench.Different parameters have been considered,such as the number of geogrid layers,embedment depth ratio,relative density of soil and height ratio of granular trench.Results showed that,without granular trench,the single layer of geogrid was more effective in enhancing the pullout capacity compared to the multilayer of geogrid reinforcement.Also,increasing the soil density and embedment depth ratio led to an increase in the uplift capacity.When soil was improved with the granular trench,the uplift force significantly increased.The granular trench improved the uplift load in dense sand more,as compared to the same symmetrical plate embedded in loose sand.Although it was observed that,in geogrid-reinforced granular trench condition,the ultimate pullout resistance at failure increased as the number of geogrid layers increased up to the third layer,and the fifth layer had a negligible effect in comparison with the third layer of reinforcement.Finite element analyses with hardening soil model for sand and CANAsand constitutive model for granular trench were conducted to investigate the failure mechanism and the associated rupture surfaces utilized.The response of granular material in the proposed model is an elastoplastic constitutive model derived from the CANAsand model,which uses a non-associated flow rule along with the concept of the state boundary surface possessing a critical and a compact state.It was observed that the granular trench might change the failure mechanism from deep plate to shallow plate as the failure surface can extend to the ground surface.The ultimate uplift capacity of anchor and the variation of surface deformation indicated a close agreement between the experiment and numerical model.展开更多
To solve the deficiency of steel anchor blot in corrosion resistance and flaw of GFRP anchor bolt in fracture resistance, our research group develops a new composite anchor bolt made of steel strands wrapped up with c...To solve the deficiency of steel anchor blot in corrosion resistance and flaw of GFRP anchor bolt in fracture resistance, our research group develops a new composite anchor bolt made of steel strands wrapped up with compound fiber resin. To improve the cohesion performance of the composite anchor bolt, pull-out tests of different composite anchor bolts with different groove intervals and depths were made and analyzed. The results show that the pulling resistance of the composite anchor bolt increases with the increase of groove interval and depth, but groove interval and depth have optimal value. Based on elastic mechanics, the cohesion between anchor bolts and anchor bodies and its distribution characteristics caused by axial tension are analyzed and cohesion formula is obtained. By contrast, the experimental result is consistent with the theoretical analysis. Therefore, the surficial change of anchor colts could influence the performance of the composite anchor bolt. The cohesion force and anchorage performance can be improved by changing the surface of anchor bolts. Research results show that the new composite anchor bolt is high-performance material in the civil engineering.展开更多
文摘Determination of the grouting anchor pullout force is a key step during the design of anchor-pull retaining wall, but it is mostly determined relied on empirical formula at present, and the rationality and the safety cannot be effectively guaranteed. Based on the engineering case of the gravity retaining wall of Qinglin Freeway, the model test was designed, and combined with the results of the ABAQUS finite element numerical analysis, it was analyzed that how the anchor axial pulling force distributes. The results showed that the force of the anchor near the wall bolt was large and which far from the wall was small and the ultimate pullout force was proportional to the length, diameter and shear strength. When the end tension of the anchor was small, the top load played a leading role on the anchor tension. This conclusion confirmed the calculation formula of ultimate pullout force was and provided a theoretical basis for anchor-pull retaining wall design and calculation.
文摘Experimental and numerical investigations have been carried out on behavior of pullout resistance of embedded circular plate with and without geogrid reinforcement layers in stabilized loose and dense sands using a granular trench.Different parameters have been considered,such as the number of geogrid layers,embedment depth ratio,relative density of soil and height ratio of granular trench.Results showed that,without granular trench,the single layer of geogrid was more effective in enhancing the pullout capacity compared to the multilayer of geogrid reinforcement.Also,increasing the soil density and embedment depth ratio led to an increase in the uplift capacity.When soil was improved with the granular trench,the uplift force significantly increased.The granular trench improved the uplift load in dense sand more,as compared to the same symmetrical plate embedded in loose sand.Although it was observed that,in geogrid-reinforced granular trench condition,the ultimate pullout resistance at failure increased as the number of geogrid layers increased up to the third layer,and the fifth layer had a negligible effect in comparison with the third layer of reinforcement.Finite element analyses with hardening soil model for sand and CANAsand constitutive model for granular trench were conducted to investigate the failure mechanism and the associated rupture surfaces utilized.The response of granular material in the proposed model is an elastoplastic constitutive model derived from the CANAsand model,which uses a non-associated flow rule along with the concept of the state boundary surface possessing a critical and a compact state.It was observed that the granular trench might change the failure mechanism from deep plate to shallow plate as the failure surface can extend to the ground surface.The ultimate uplift capacity of anchor and the variation of surface deformation indicated a close agreement between the experiment and numerical model.
文摘To solve the deficiency of steel anchor blot in corrosion resistance and flaw of GFRP anchor bolt in fracture resistance, our research group develops a new composite anchor bolt made of steel strands wrapped up with compound fiber resin. To improve the cohesion performance of the composite anchor bolt, pull-out tests of different composite anchor bolts with different groove intervals and depths were made and analyzed. The results show that the pulling resistance of the composite anchor bolt increases with the increase of groove interval and depth, but groove interval and depth have optimal value. Based on elastic mechanics, the cohesion between anchor bolts and anchor bodies and its distribution characteristics caused by axial tension are analyzed and cohesion formula is obtained. By contrast, the experimental result is consistent with the theoretical analysis. Therefore, the surficial change of anchor colts could influence the performance of the composite anchor bolt. The cohesion force and anchorage performance can be improved by changing the surface of anchor bolts. Research results show that the new composite anchor bolt is high-performance material in the civil engineering.
