Effect of annealing temperature on microstructure and mechanical properties of Mg-Zn-Zr-Nd alloy with large final rolling deformation

In this study,the Mg-3Zn-0.5Zr-χNd(χ=0,0.6)alloys were subjected to final rolling treatment with large deformation of 50%.The impact of annealing temperatures on the microstructure and mechanical properties was investigated.The rolled Mg-3Zn-0.5Zr-0.6Nd alloy exhibited an ultimate tensile strength of 386 MPa,a yield strength of 361 MPa,and an elongation of 7.1%.Annealing at different temperatures resulted in reduced strength and obviously increased elongation for both alloys.Optimal mechanical properties for the Mg-3Zn-0.5Zr-0.6Nd alloy were achieved after annealing at 200℃,with an ultimate tensile strength of 287 MPa,a yield strength of 235 MPa,and an elongation of 26.1%.The numerous deformed microstructures,twins,and precipitated phases in the rolled alloy could impede the deformation at room temperature and increase the work hardening rate.After annealing,a decrease in the work hardening effect and an increase in the dynamic recovery effect were obtained due to the formation of fine equiaxed grains,and the increased volume fraction of precipitated phases,which significantly improved the elongation of the alloy.Additionally,the addition of Nd element could enhance the annealing recrystallization rate,reduce the Schmid factor difference between basal and prismatic slip systems,facilitate multi-system slip initiation and improve the alloy plasticity.

Achieving High Strength and Tensile Ductility in Pure Nickel by Cryorolling with Subsequent Low-Temperature Short-Time Annealing

Ultra fine-grained pure metals and their alloys have high strength and low ductility.In this study,cryorolling under different strains followed by low-temperature short-time annealing was used to fabricate pure nickel sheets combining high strength with good ductility.The results show that,for different cryorolling strains,the uniform elongation was greatly increased without sacrificing the strength after annealing.A yield strength of 607 MPa and a uniform elongation of 11.7%were obtained after annealing at a small cryorolling strain(ε=0.22),while annealing at a large cryorolling strain(ε=1.6)resulted in a yield strength of 990 MPa and a uniform elongation of 6.4%.X-ray diffraction(XRD),transmission electron microscopy(TEM),scanning electron microscopy(SEM),and electron backscattered diffraction(EBSD)were used to characterize the microstructure of the specimens and showed that the high strength could be attributed to strain hardening during cryorolling,with an additional contribution from grain refinement and the formation of dislocation walls.The high ductility could be attributed to annealing twins and micro-shear bands during stretching,which improved the strain hardening capacity.The results show that the synergistic effect of strength and ductility can be regulated through low-temperature short-time annealing with different cryorolling strains,which provides a new reference for the design of future thermo-mechanical processes.

Achievable hole concentration at room temperature as a function of Mg concentration for MOCVD-grown p-GaN after sufficient annealing

Relationship between the hole concentration at room temperature and the Mg doping concentration in p-GaN grown by MOCVD after sufficient annealing was studied in this paper.Different annealing conditions were applied to obtain sufficient activation for p-GaN samples with different Mg doping ranges.Hole concentration,resistivity and mobility were characterized by room-temperature Hall measurements.The Mg doping concentration and the residual impurities such as H,C,O and Si were measured by secondary ion mass spectroscopy,confirming negligible compensations by the impurities.The hole concentration,resistivity and mobility data are presented as a function of Mg concentration,and are compared with literature data.The appropriate curve relating the Mg doping concentration to the hole concentration is derived using a charge neutrality equation and the ionized-acceptor-density[N-(A)^(-)](cm^(−3))dependent ionization energy of Mg acceptor was determined asE_(A)^(Mg)=184−2.66×10^(−5)×[N_(A)^(-)]1/3 meV.

Advancing Al-doped ZnO thin films structural,optical and electrical properties of low temperature PET substrates via flash lamp annealing

In this study,aluminum-doped zinc oxide(AZO)thin films were deposited onto a low-temperature polyethylene terephthalate(PET)substrate using DC magnetron sputtering.Deposition parameters included power range of 100-300 W,a working pressure of 15 mTorr,and a substrate temperature of 50°C.Post-deposition,flash lamp annealing(FLA)was employed as a rapid thermal processing method with a pulse duration of 1.7 ms and energy density of 7 J·cm-2,aimed at enhancing the film's quality while preserving the temperature-sensitive PET substrate.FLA offers advantages over conventional annealing,including shorter processing times and improved material properties.The structural,optical,and electrical characteristics of the AZO films were assessed using X-ray diffraction,field emission scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy,ultraviolet-visible spectroscopy,and Hall effect measurements.The results demonstrated that properties of AZO films varied with deposition and annealing conditions.Films deposited at 200 W and subjected to FLA exhibited superior crystallinity,with average visible light transmittance exceeding 80%and resistivity as low as 0.38Ω·cm representing 95%improvement in transmittance.Electrical analysis revealed that carrier concentration,mobility,and resistivity were influenced by both sputtering and annealing parameters.These findings underscore the effectiveness of FLA in optimizing AZO thin film properties,highlighting potential in optoelectronics applications.

Effects of the extrusion parameters on microstructure,texture and room temperature mechanical properties of extruded Mg-2.49Nd-1.82Gd-0.2Zn-0.2Zr alloy

Microstructure,texture,and mechanical properties of the extruded Mg-2.49Nd-1.82Gd-0.2Zn-0.2Zr alloy were investigated at different extrusion temperatures(260 and 320℃),extrusion ratios(10:1,15:1,and 30:1),and extrusion speeds(3 and 6 mm/s).The experimental results exhibited that the grain sizes after extrusion were much finer than that of the homogenized alloy,and the second phase showed streamline distribution along the extrusion direction(ED).With extrusion temperature increased from 260 to 320℃,the microstructure,texture,and mechanical properties of alloys changed slightly.The dynamic recrystallization(DRX)degree and grain sizes enhanced as the extrusion ratio increased from 10:1 to 30:1,and the strength gradually decreased but elongation(EL)increased.With the extrusion speed increased from 3 to 6 mm/s,the grain sizes and DRX degree increased significantly,and the samples presented the typical<2111>-<1123>rare-earth(RE)textures.The alloy extruded at 260℃ with extrusion ratio of 10:1 and extrusion speed of 3 mm/s showed the tensile yield strength(TYS)of 213 MPa and EL of 30.6%.After quantitatively analyzing the contribution of strengthening mechanisms,it was found that the grain boundary strengthening and dislocation strengthening played major roles among strengthening contributions.These results provide some guidelines for enlarging the industrial application of extruded Mg-RE alloy.

Ideal Bi‑Based Hybrid Anode Material for Ultrafast Charging of Sodium‑Ion Batteries at Extremely Low Temperatures

Sodium-ion batteries have emerged as competitive substitutes for low-temperature applications due to severe capacity loss and safety concerns of lithium-ion batteries at−20°C or lower.However,the key capability of ultrafast charging at ultralow temperature for SIBs is rarely reported.Herein,a hybrid of Bi nanoparticles embedded in carbon nanorods is demonstrated as an ideal material to address this issue,which is synthesized via a high temperature shock method.Such a hybrid shows an unprecedented rate performance(237.9 mAh g^(−1)at 2 A g^(−1))at−60℃,outperforming all reported SIB anode materials.Coupled with a Na_(3)V_(2)(PO_(4))_(3)cathode,the energy density of the full cell can reach to 181.9 Wh kg^(−1)at−40°C.Based on this work,a novel strategy of high-rate activation is proposed to enhance performances of Bi-based materials in cryogenic conditions by creating new active sites for interfacial reaction under large current.

Novel Methodologies for Preventing Crack Propagation in Steel Gas Pipelines Considering the Temperature Effect

Using the software ANSYS-19.2/Explicit Dynamics,this study performedfinite-element modeling of the large-diameter steel pipeline cross-section for the Beineu-Bozoy-Shymkent gas pipeline with a non-through straight crack,strengthened by steel wire wrapping.The effects of the thread tensile force of the steel winding in the form of single rings at the crack edges and the wires with different winding diameters and pitches were also studied.The results showed that the strengthening was preferably executed at a minimum value of the thread tensile force,which was 6.4%more effective than that at its maximum value.The analysis of the influence of the winding dia-meters showed that the equivalent stresses increased by 32%from the beginning of the crack growth until the wire broke.The increment in winding diameter decelerated the disclosure of the edge crack and reduced its length by 8.2%.The analysis of the influence of the winding pitch showed that decreasing the distance between the winding turns also led to a 33.6%reduction in the length of the straight crack and a 7.9%reduction in the maximum stres-ses on the strengthened pipeline cross-section.The analysis of the temperature effect on the pipeline material,within a range from-40℃ to+50℃,resulted in a crack length change of up to 5.8%.As the temperature dropped,the crack length decreased.Within such a temperature range,the maximum stresses were observed along the cen-tral area of the crack,which were equal to 413 MPa at+50℃ and 440 MPa at-40℃.The results also showed that the presence of the steel winding in the pipeline significantly reduced the length of crack propagation up to 8.4 times,depending on the temperature effect and design parameters of prestressing.This work integrated the existing methods for crack localization along steel gas pipelines.

Effect of High Temperature Annealing on Characteristics of 4H Silicon Carbide MESFET

For very high temperature annealing (1620℃) after ion implantation for 4H silicon carbide (4H SiC),the residual components of Al and O in the alundum furnace impact seriously on the surface of material,which yields the derivation of SiOC.This causes a significant degradation of the 4H SiC surface characteristics according to the results of surface composition analysis.As validity,Ni/SiC ohmic contact measurement illustrates a higher specific contact resistance than the normal value by a factor of 2～3.Consequently the MESFET fabricated with this kind of 4H SiC material results in a degraded I V output performance compared with that of normal 4H SiC MESFET.

Annealing Temperature-Dependent Luminescence Color Coordination in Eu-Doped AlN Thin Films

AlN was used as a host material and doped with Eu grown on Si substrate by pulsed laser deposition (PLD) with low substrate temperature. The X-ray diffraction (XRD) data revealed the orientation and the composition of the thin film. The surface morphology was studied by scanning electron microscope (SEM). While raising the annealing temperatures from 300˚C to 900˚C, the emission was observed from AlN: Eu under excitation of 260 nm excitation. The photoluminescence (PL) was integrated over the visible light wavelength shifted from the blue to the red zone in the CIE 1931 chromaticity coordinates. The luminescence color coordination of AlN: Eu depending on the annealing temperatures guides the further study of Eu-doped nitrides manufacturing on white light emitting diode (LED) and full color LED devices.

Effect of annealing temperature on joints of diffusion bonded Mg/Al alloys

To study the effect of annealing temperature on the joints between magnesium and aluminum alloys, and improve the properties of bonding layers, composite plates of magnesium alloy（AZ31 B） and aluminum alloy（6061） were welded using the vacuum diffusion bonding method. The composite specimens were continuously annealed in an electrical furnace under the protection of argon gas. The microstructures were then observed using scanning electron microscopy. X-ray diffractometry was used to investigate the residual stresses in the specimens. The elemental distribution was analyzed with an electron probe micro analyzer. The tensile strength and hardness were also measured. Results show that the diffusion layers become wide as the heat treatment temperature increases, and the residual stress of the specimen is at a minimum and tensile strength is the largest when being annealed at 250 ℃. Therefore, 250 ℃ is the most appropriate annealing temperature.

Effect of annealing temperature on martensitic transformation of Ti_(49.2)Ni_(50.8) alloy processed by equal channel angular pressing

The effect of annealing temperature on the martensitic transformation of a Ti49.2Ni50.8 alloy processed by equal channel angular pressing （ECAP） was investigated by X-ray diffraction （XRD）, transmission electron microscopy （TEM） and differential scanning calorimetry （DSC）. The as-ECAP processed and subsequently annealed Ti49.2Ni50.8 alloys consist of B2 parent phase, Ti4Ni2O phase and B19′ martensite at room temperature. Upon cooling, all samples show B2→R→B19′ two-stage transformation. Upon heating, when the annealing temperature is less than 400℃, the samples show B19′→R→B2 two-stage transformation; when the annealing temperature is higher than 500 ℃, the samples show B19′→B2 single-stage transformation. The B2-R transformation is characterized by wide interval due to the dislocations introduced during ECAP.

Effects of annealing temperature on the microstructure and properties of the 25Mn-3Si-3Al TWIP steel

Microstructures and mechanical properties of the 25Mn twinning induced plasticity （TWIP） steel at different annealing temperatures were investigated. The results indicated that when the annealing temperature was 1000℃, the 25Mn steel showed excellent comprehensive mechanical properties, the tensile strength was about 640 MPa, the yield strength was higher than 255 MPa, and the elongation was above 82%. The microstructure was analyzed by optical microscopy （OM）, X-ray diffraction （XRD）, and transmission electron microscopy （TEM）. Before deformation the microstructure was composed of austenitic matrix and annealing twins at room temperature; at the same time, a significant amount of annealing twins and stacking faults were observed by TEM. Mechanical twins played a dominant role in deformation and as a result the mechanical properties were found to be excellent.

Effect of annealing temperature on microstructure and electrochemical performance of La_(0.75)Mg_(0.25)Ni_(3.5)Co_(0.2) hydrogen storage electrode alloy

To improve the cyclic stability of La-Mg-Ni system alloy, as-cast La0.75Mg0.25Ni3.5Co0.2 alloy was annealed at 1123, 1223, and 1323 K for 10 h in 0.3 MPa argon. The microstructure and electrochemical performance of different annealed alloys were investigated systematically by X-Ray Diffraction （XRD）, Scanning Electron Microscopy （SEM）, X-Ray Photoelectron Spectroscopy （XPS）, and electrochemical experiments. The results obtained by XRD and SEM showed that the as-cast and annealed （1123 K） alloys had multiphase structure containing LaNis, （La, Mg）2（Ni, Co）7 and few LaNi2 phases. When annealing temperatures approached 1223 and 1323 K, LaNi2 phase disappeared. The annealed alloys at 1223 and 1323 K were composed of LaNi5, （La, Mg）2（Ni, Co）7 and （La, Mg）（Ni, Co）3 phases. With increasing annealing temperature, the maximum discharge capacity of the alloy decreased monotonously, but the cyclic stability was improved owing to structure homogeneity and grain growth after annealing, as well as the enhancement of anti-oxidation/corrosion ability and the suppression of pulverization during cycling in KOH electrolyte.

Effect of Zr additions and annealing temperature on electrical conductivity and hardness of hot rolled Al sheets

The influence of annealing cycles up to 650 °C on the specific conductivity and hardness（HV） of hot-rolled sheets of Al alloys containing up to 0.5% Zr（mass fraction） was studied.Using analytical calculations of phase composition and experimental methods（scanning electron microscopy,transmission electron microscopy,electron microprobe analysis,etc）,it is demonstrated that the conductivity depends on the content of Zr in the Al solid solution which is the minimum after holding at 450 °C for 3 h.On the other hand,the hardness of the alloy is mainly caused by the amount of nanoparticles of the L12（Al3Zr） phase that defines the retention of strain hardening.It is shown that the best combination of electrical conductivity and hardness values can be reached within an acceptable holding time at the temperature about 450 °C.

Effects of substrate temperature and annealing treatment on the microstructure and magnetic characteristics of TbDyFe films

A series of TbDyFe films were prepared by DC magnetron sputtering. The effects of substrate temperature and annealing temperature on the phase structure and the magnetic properties of the sample films were investigated. The an-nealing treatment has a significant influence on the microstructure and the magnetic properties of the sample. The results obtained by XRD indicate that the films deposited at a temperature lower than 525℃ are amorphous and have an easy magnetization direction perpendicular to the film plane. An RFe2 phase is formed in the sample annealed at 550℃ and the residual phases observed are Fe and rare earth oxide. The magnetic properties Hc and Mr/Ms of the film annealed at 550℃ obtain the maximum values,for which the formation of the RFe2 phase is mainly responsible. An annealing treatment leads to a rotation of the sample’s easy axis from being parallel to the film surface to becoming vertical.

Effect of decarburization annealing temperature and time on the carbon content, microstructure, and texture of grain-oriented pure iron

In this study,the effect of decarburization annealing temperature and time on the carbon content,microstructure,and texture of grain-oriented pure iron was investigated by optical microscopy and scanning electron microscopy with electron-backscatter diffraction. The results showed that the efficiency of decarburization dramatically increased with increasing decarburization temperature. However,when the annealing temperature was increased to 825°C and 850°C,the steel's carbon content remained essentially unchanged at 0.002%. With increasing decarburization time,the steel's carbon content generally decreased. When both the decarburization temperature and time were increased further,the average grain size dramatically increased and the number of fine grains decreased; meanwhile,some relatively larger grains developed. The main texture types of the decarburized sheets were approximately the same: {001}<110> and {112~115}<110>,with a γ-fiber texture. Furthermore,little change was observed in the texture. Compared with the experimental sheets,the texture of the cold-rolled sheet was very scattered. The best average magnetic induction(B_(800)) among the final products was 1.946 T.

Effects of annealing temperature on microstructure and ferroelectric properties of Bi_(0.5)(Na_(0.85)K_(0.15))_(0.5)TiO_3 thin films

Bi0.5(Na0.85K0.15)0.5TiO3(BNKT15) thin films were synthesized by metal-organic decomposition(MOD) at annealing temperatures of 650,680,710 and 740℃,and the effects of annealing temperature on the microstructure,dielectric properties,remnant polarization(2Pr) and leakage current density were studied with X-ray diffractometer,atomic force microscope,precision impedance analyzer,ferroelectric analysis station and semiconductor parameter tester.The results show that the thin film annealed at 710℃ exhibits a typical perovskite structure without predominant orientation and a smooth surface with evenly distributed grains.2Pr value(67.4 μC/cm2 under 830 kV/cm) and the leakage current density(1.6×10-6 A/cm2 at 170 kV/cm) for BNKT15 thin film annealed at 710℃ are better than those for thin films annealed at other temperatures.

Growth and annealing study of hydrogen-doped single diamond crystals under high pressure and high temperature

A series of diamond crystals doped with hydrogen is successfully synthesized using LiH as the hydrogen source in a catalyst-carbon system at a pressure of 6.0 GPa and temperature ranging from 1255 C to 1350 C.It is shown that the high temperature plays a key role in the incorporation of hydrogen atoms during diamond crystallization.Fourier transform infrared micro-spectroscopy reveals that most of the hydrogen atoms in the synthesized diamond are incorporated into the crystal structure as sp 3-CH 2-symmetric（2850 cm-1） and sp 3 CH 2-antisymmetric vibrations（2920 cm-1）.The intensities of these peaks increase gradually with an increase in the content of the hydrogen source in the catalyst.The incorporation of hydrogen impurity leads to a significant shift towards higher frequencies of the Raman peak from 1332.06 cm-1 to 1333.05 cm-1 and gives rise to some compressive stress in the diamond crystal lattice.Furthermore,hydrogen to carbon bonds are evident in the annealed diamond,indicating that the bonds that remain throughout the annealing process and the vibration frequencies centred at 2850 and 2920 cm-1 have no observable shift.Therefore,we suggest that the sp 3 C-H bond is rather stable in diamond crystals.

The effect of high-temperature annealing on LaFe_(11.5)Si_(1.5) and the magneto-caloric properties of La_(1-x)Ce_xFe_(11.5)Si_(1.5) compounds

The powder X-ray diffraction patterns of LaFell.sSil.5 compounds annealed at different high temperatures from 1323 K （5 h） to 1623 K （2 h） show that a large amount of 1：13 phase begins to form in LaFell.sSiL5 compound annealed at 1423 K （5 h）. In the temperature range from 1423 to 1523 K, ^-Fe and LaFeSi phases rapidly decrease to form 1：13 phase. LaFeSi phase is rarely observed, and the most amount of 1：13 phase is obtained in the compound annealed at 1523 K （5 h）. With the annealing temperature increasing to 1573 and 1623 K, LaFeSi is detected again in the LaFell.sSil.s compound. According to the results of annealing at different high-temperatures, the Lal-xCexFelt.sSit.5 compounds are annealed at high temperatures of 1373 K （2 h） ＋ 1523 K （5 h）. The main phase is NaZn13-type phase, and the impurity is a small amount of et-Fe in Lal-xCexFexx.sSil.5 compounds with 0 〈 x 〈 0.35, and there is a large amount of CeaFe17 phase in Lao.sCeo.sFela.sSil.s. It indicates that the substitution of cerium atoms for La in LaFelLsSil.5 compounds has limit. At the same time, the substitution of Ce for La has large effect on magnetocaloric properties. With increasing Ce content from x = 0 to x = 0.35, the Curie temperature decreases linearly from 196 to 168 K, the magnetic entropy change increases from 16.5 to 57.3 J-kg-kK-1 in a low magnetic field change of 0-2 T, and the thermal hysteresis also increases from 3 K to 8 K.

Effect of annealing temperature on the microstructure and optoelectrical properties of ZnO thin films and their application in self-powered accelerometers

This paper reports a piezoelectric nanogenerator(NG) with a thickness of approximately 80 μm for miniaturized self-powered acceleration sensors. To deposit the piezoelectric zinc oxide(ZnO) thin film, a magnetron sputtering machine was used. Polymethyl methacrylate(PMMA) and aluminum-doped zinc oxide(AZO) were used as the insulating layer and the top electrode of the NG, respectively. The experimental results show that the ZnO thin films annealed at 150℃ exhibited the highest crystallinity among the prepared films and an optical band gap of 3.24 eV. The NG fabricated with an AZO/PMMA/ZnO/stainless steel configuration exhibited a higher output voltage than the device with an AZO/ZnO/PMMA/stainless steel configuration. In addition, the annealing temperature affected the open-circuit voltage of the NGs;the output voltage reached 3.81 V when the annealing temperature was 150℃. The open-circuit voltage of the prepared self-powered accelerometer increased linearly with acceleration. In addition, the small NG-based accelerometer, which exhibited excellent fatigue resistance, can be used for acceleration measurements of small and lightweight devices.