Nowadays validation of anti-lock braking systems（ABS） relies mainly on a large amount of road tests.An alternative means with higher efficiency is employing the hardware-in-the-loop simulation（HILS） system to subs...Nowadays validation of anti-lock braking systems（ABS） relies mainly on a large amount of road tests.An alternative means with higher efficiency is employing the hardware-in-the-loop simulation（HILS） system to substitute part of road tests for designing,testing,and tuning electronic control units（ECUs） of ABS.Most HILS systems for ABS use expensive digital signal processor hardware and special purpose software,and some fail-safe functions with regard to wheel speeds cannot be evaluated since artificial wheel speed signals are usually provided.In this paper,a low-cost ABS HILS test bench is developed and used for validating the anti-lock braking performance and tuning control parameters of ABS controllers.Another important merit of the proposed test bench is that it can comprehensively evaluate the fail-safe functions with regard to wheel speed signals since real tone rings and sensors are integrated in the bench.A 5-DOF vehicle model with consideration of longitudinal load transfer is used to calculate tire forces,wheel speeds and vehicle speed.Each of the four real-time wheel speed signal generators consists of a servo motor plus a ring gear,which has sufficient dynamic response ability to emulate the rapid changes of the wheel speeds under strict braking conditions of very slippery roads.The simulation of braking tests under different road adhesion coefficients using the HILS test bench is run,and results show that it can evaluate the anti-lock braking performance of ABS and partly the fail-safe functions.This HILS system can also be used in such applications as durability test,benchmarking and comparison between different ECUs.The test bench developed not only has a relatively low cost,but also can be used to validate the wheel speed-related ECU design and all its fail-safe functions,and a rapid testing and proving platform with a high efficiency for research and development of the automotive ABS is therefore provided.展开更多
Based on the vehicle-road dynamic model, the road characteristic parameter, which depends on different types of road surfaces, is introduced and a new method of road surface identification for automotive anti-lock bra...Based on the vehicle-road dynamic model, the road characteristic parameter, which depends on different types of road surfaces, is introduced and a new method of road surface identification for automotive anti-lock braking system (ABS) is proposed. According to the characteristics of vehicle-road dynamic model, a simple math resolution method of the model's factors is established. Only using the information of wheel speed, the vehicle reference velocity and the wheel slip ratio are estimated real-timely. And based on the wheel dynamic model, the road characteristic parameter is determined to identify the road surface for the determination of thresholds of ABS regulative parameters. With this new method, the road surface identification can be accurately obtained and calculation time is short that it can meet the ABS real time control need, and it also improves the performance of ABS.展开更多
This paper presents the model of one-tire kinetics、tires、the braking system and the model of control system.On virtual road,this paper builds a fuzzy predictive control system to insure the best attachment coefficie...This paper presents the model of one-tire kinetics、tires、the braking system and the model of control system.On virtual road,this paper builds a fuzzy predictive control system to insure the best attachment coefficient between tires and road. And it turns out to be that this fuzzy predictive control method has achieved good performances.展开更多
Anti lock brake systems (ABS) are now widely used on motor vehicles. To reduce product cost and to use currently available technologies, standard ABS uses only wheel speed sensors to detect wheel angular velocities...Anti lock brake systems (ABS) are now widely used on motor vehicles. To reduce product cost and to use currently available technologies, standard ABS uses only wheel speed sensors to detect wheel angular velocities, which is not enough to directly obtain wheel slip ratios needed by the control unit, but can be used to calculate reference slip ratios with measured wheel angular velocities and the estimated vehicle speed. Therefore, the road friction coefficient, which determines the vehicle deceleration during severe braking, is an important parameter in estimating vehicle speed. This paper analyzes wheel acceleration responses in simulations of severe braking on different road surfaces and selects a pair of specific points to identify the wheel acceleration curve for each operating condition, such as road surface, pedal braking torque and wheel vertical load. It was found that the curve using the selected points for each road surface clearly differs from that of the other road surfaces. Therefore, different road surfaces can be distinguished with these selected points which represent their corresponding road surfaces. The analysis assumes that only wheel speed sensors are available as hardware and that the road cohesion condition can be determined in the initial part of the severe braking process.展开更多
基金supported by National Natural Science Foundation of China(Grant No.50908008)National Hi-tech Research and Development Program of China(863Program,Grant No.2009AA11Z216)
文摘Nowadays validation of anti-lock braking systems（ABS） relies mainly on a large amount of road tests.An alternative means with higher efficiency is employing the hardware-in-the-loop simulation（HILS） system to substitute part of road tests for designing,testing,and tuning electronic control units（ECUs） of ABS.Most HILS systems for ABS use expensive digital signal processor hardware and special purpose software,and some fail-safe functions with regard to wheel speeds cannot be evaluated since artificial wheel speed signals are usually provided.In this paper,a low-cost ABS HILS test bench is developed and used for validating the anti-lock braking performance and tuning control parameters of ABS controllers.Another important merit of the proposed test bench is that it can comprehensively evaluate the fail-safe functions with regard to wheel speed signals since real tone rings and sensors are integrated in the bench.A 5-DOF vehicle model with consideration of longitudinal load transfer is used to calculate tire forces,wheel speeds and vehicle speed.Each of the four real-time wheel speed signal generators consists of a servo motor plus a ring gear,which has sufficient dynamic response ability to emulate the rapid changes of the wheel speeds under strict braking conditions of very slippery roads.The simulation of braking tests under different road adhesion coefficients using the HILS test bench is run,and results show that it can evaluate the anti-lock braking performance of ABS and partly the fail-safe functions.This HILS system can also be used in such applications as durability test,benchmarking and comparison between different ECUs.The test bench developed not only has a relatively low cost,but also can be used to validate the wheel speed-related ECU design and all its fail-safe functions,and a rapid testing and proving platform with a high efficiency for research and development of the automotive ABS is therefore provided.
文摘Based on the vehicle-road dynamic model, the road characteristic parameter, which depends on different types of road surfaces, is introduced and a new method of road surface identification for automotive anti-lock braking system (ABS) is proposed. According to the characteristics of vehicle-road dynamic model, a simple math resolution method of the model's factors is established. Only using the information of wheel speed, the vehicle reference velocity and the wheel slip ratio are estimated real-timely. And based on the wheel dynamic model, the road characteristic parameter is determined to identify the road surface for the determination of thresholds of ABS regulative parameters. With this new method, the road surface identification can be accurately obtained and calculation time is short that it can meet the ABS real time control need, and it also improves the performance of ABS.
文摘This paper presents the model of one-tire kinetics、tires、the braking system and the model of control system.On virtual road,this paper builds a fuzzy predictive control system to insure the best attachment coefficient between tires and road. And it turns out to be that this fuzzy predictive control method has achieved good performances.
基金the Major Research Project of the Ninth-Five Plan (1996 - 2 0 0 0 ) of China (No. 96 - A0 5 - 0 5 - 0 2 )
文摘Anti lock brake systems (ABS) are now widely used on motor vehicles. To reduce product cost and to use currently available technologies, standard ABS uses only wheel speed sensors to detect wheel angular velocities, which is not enough to directly obtain wheel slip ratios needed by the control unit, but can be used to calculate reference slip ratios with measured wheel angular velocities and the estimated vehicle speed. Therefore, the road friction coefficient, which determines the vehicle deceleration during severe braking, is an important parameter in estimating vehicle speed. This paper analyzes wheel acceleration responses in simulations of severe braking on different road surfaces and selects a pair of specific points to identify the wheel acceleration curve for each operating condition, such as road surface, pedal braking torque and wheel vertical load. It was found that the curve using the selected points for each road surface clearly differs from that of the other road surfaces. Therefore, different road surfaces can be distinguished with these selected points which represent their corresponding road surfaces. The analysis assumes that only wheel speed sensors are available as hardware and that the road cohesion condition can be determined in the initial part of the severe braking process.
