Influence of Different Chelating Agents on Corrosion Performance of Microstructured Hydroxyapatite Coatings on AZ91D Magnesium Alloy

To improve the bioactivity and corrosion resistance of AZ91 D magnesium alloy,hydroxyapatite（HAp） coatings with novel microstructured morphologies were prepared successfully on AZ91 D substrates via a facile hydrothermal method.Different chelating agents including polyaspartic acid（PASP） and ethylenediaminetetraacetic acid（EDTA） were introduced to investigate their effects on the morphology and corrosion resistance of the coated magnesium alloys.The results revealed that the coating prepared with PASP was composed of many uniform urchin-like microspheres,while the coating prepared with EDTA consisted of many flower-like particles.Moreover,the crystallinity of the coating prepared with EDTA was much higher than that of the coating prepared with PASP.Electrochemical tests revealed that the corrosion resistance of the substrate was significantly improved after being coated with each coating.Immersion test of the coated samples in simulated body fluid（SBF） demonstrated that the coatings could be biodegraded gradually and induce the formation of calcium phosphate particles.

Preparation technology and anti-corrosion performances of black ceramic coatings formed by micro-arc oxidation on aluminum alloys

In order to prepare ornamental and anti-corrosive coating on aluminum alloys, preparation technology of black micro-arc ceramic coatings on Al alloys in silicate based electrolyte was studied. The influence of content of Na2WO4 and combination additive in solution on the performance of black ceramic coatings was studied; the anticorrosion performances of black ceramic coatings were evaluated through whole-immersion test and electrochemical method in 3.5% NaCl solution at different pH value; SEM and XRD were used to analyze the surface morphology and phase constitutes of the black ceramic coatings. Experimental results indicated that, without combination additives, with the increasing of Na2WO4 content in the electrolyte, ceramic coating became darker and thicker, but the color was not black; after adding combination additive, the coating turned to be black; the black ceramic coating was multi-hole form in surface. There was a small quantity of tungsten existing in the black ceramic coating beside α-Al2O3 phase and β-Al2O3 phase. And aluminum alloy with black ceramic coating exhibited excellent anti-corrosion property in acid, basic and neutral 3.5% NaCl solution.

Corrosion behavior of B30 Cu-Ni alloy and anti-corrosion coating in marine environment

The corrosion behavior of B30 Cu-Ni alloy in a sterile seawater and a SRB solution was investigated. The results show that the corrosion potential of specimen in the SRB solution is much lower than that in the sterile seawater. The polarization resistance of specimen in the SRB solution decreases quickly after a period immersion and becomes much lower than that in the sterile seawater. It is concluded that the SRB accelerates the corrosion process of B30 Cu-Ni alloy greatly. An anti-corrosion electroless Ni-P coating was produced and applied to the alloy. The results show that specimens coated with Ni-P plating exhibit favorable corrosion resistance property in SRB solution. Severe pitting corrosion appears on the uncoated specimens in the SRB solution when the coated specimens are still in good condition. The anti-corrosion mechanism of Ni-P plating was analyzed. It is concluded that coating the B30 Cu-Ni alloy with electroless Ni-P plating is an effective technique against the attack of SRB in marine environment.

A Comparative Study on Several Anti-Corrosion Materials for Power FGD System

In the study organic-inorganic hybrid composite, epoxy modified silicone coating and vinyl ester flake mastic were comparatively used as several anti-corrosion materials that provided protection for flue gas desulfu-rization (FGD). The relationship between curing conversion rate of hybrid polymer and temperature was investigated by differential scanning calorimeter (DSC). The adhesion strength, coefficient of thermal expansion and flame retardant properties of three anti-corrosion materials were measured and analyzed. A corrosion test in 8% H2SO4 and 5% HCl at temperature cycle of 40°C~ 160°C was applied to study corrosion resistance of several anti-corrosion materials. Gravimetric measurement and morphological observation of three materials before and after corrosion test were comparatively analyzed in the paper. The small weight change and good morphological structure of hybrid composite during corrosion test demonstrate that hybrid composite has better anti-corrosion properties than epoxy modified silicone coating and vinyl ester flake mastic.

Influence of graphene on the anti-corrosion performance of epoxy-based coatings

In this work, graphene-modified epoxy-based anti-corrosion coatings were prepared and the influence of graphene on the anti-corrosion performance of the epoxy-based coatings was investigated with water contact angle test ,chemical solution immersion test, and electrochemical test. The water contact angle and chemical solution resistance of the epoxy-based coatings were improved with an increase in graphene content from 0 to 0.4%. These results prove that addition of graphene can significantly improve the hydrophobicity and impermeability of epoxy- based coatings. However, when the graphene content was increased to 0.5%, the performance of the epoxy-based coatings decreased because of graphene aggregation. Tafel polarization results show that graphene addition can significantly reduce the corrosion current density and corrosion potential of epoxy-based coatings, which enhance their anti-corrosion performance.

An electrochemical method for evaluating the resistance to cathodic disbondment of anti-corrosion coatings on buried pipelines

Methods for evaluating the resistance to cathodic disbondment （RCD） of anti-corrosion coatings on buried pipelines were reviewed. It is obvious that these traditional cathodic disbondment tests （CDT） have some disadvantages and the evaluated results are only simple figures and always rely on the subjective experience of the operator. A new electrochemical method for evaluating the RCD of coatings, that is, the potentiostatic evaluation method （PEM）, was developed and studied. During potentiostatic anodic polarization testing, the changes of stable polarization current of specimens before and after cathodic disbonding （CD） were measured, and the degree of cathodic disbondment of the coating was quantitatively evaluated, among which the equivalent cathodic disbonded distance AD was suggested as a parameter for evaluating the RCD. A series of testing parameters of the PEM were determined in these experiments.

Development of Exterior Anti-corrosion Coating Production Line for Large Diameter Hot Bent Pipes

The epoxy powder exterior anti-corrosion coating production line for bent pipes with a single (double) course production is a technologically advanced bent pipe anti corrosion method with cost efficiency, environment friendliness and stable coating quality. The quality of the coating on the bent pipe fully meets the requirements of the current national and industrial standards. The application of the technology has filled the gap in the bent pipe anti corrosion coating area of China, and leads the world technologically. With this technology the coating quality of the bent pipe has greatly improved, resulting in significant social and economic benefits. With the use of the technology in various large scale pipeline projects such as the "West to East Gas Pipeline Project", it will exhibite a greater potential in the future pipeline projects with a broad application prospect.

Effect of Synergistic Anticorrosion Treatments on Cycling Stability of Mg-Based Hydrogen Storage Electrode

In this paper, any two of the three anticorrosion agents, that is emulsifier (OP-10), soluble glass (Na2O·nSiO2) and glycerin (C3H8O3), were treated simultaneously on the surface of amorphous (a- ) MgNi + 5% Ml2Mg17(MI denotes the lanthanum-rich mish metal) electrode and the electrolyte. Effect of the synergistic anticorrosion treatment on charging/discharging cycle stability of the electrode was investigated. Contrasted with single treatment method, the cycling stability of the electrodes was further improved. The desirable synergistic anticorrosion method was that the electrode was treated by the soluble glass, and that OP-10 was added into the electrolyte. The cyclic voltammogram (CV) results of the electrode show clearly that the anticorrosion agent can change the electrochemical activity and mechanism of the electrode. The concentration of the anticorrosion agent in the electrolyte treated by the synergistic anticorrosion method was also investigated. The appropriate concentration of the anticorrosion agents in the electrolyte is 0.143% .

The Effect of Cerium Dioxide (CeO_2) in an Anti-corrosion and Self-lubricating Coating

The effect of cerium dioxide(CeO_2)as an additive on the structure and properties of a melting type coating has been studied by means of microhardness measurement,scanning electron microscopy and thermal analysis. The results show that cerium dioxide can modify the microstructure and tribological properties of the coating. Model LIC-23 composite coating which contains CeO_2 performs well as a self-lubricating coating in hydrochloric acid solution.

A novel anti-corrosion coating for magnesium alloy

A novel enviromental protective water based metallic coating were prepared on the surface of AZ91D magnesium alloy. The properties and structure of the coating were investigated by adhension test, hardness test, heat resisting test, neutral salt spray test and scanning electron microscopy (SEM). The results show that the coating has a stepped structure which can achieve good adhesion of first-grade, heat resistance temperature of 400℃, hardness of HV_ 0.50/30210 and anti-corrosion time of 250h in salt spray test. Meanwhile, the film forming and corrosion mechanism of the coating were also put forward based on the results of the Fourier transform infrared spectroscopy (FTIR) test and electrochemical impedance spectroscopy (EIS) test.

Anti-Corrosion Test on Basal Slope Protection Materials

Through the introduction of the anti-corrosion test schemes, the test equipments and the test procedure for three kinds of basal slop protection materials including fence, mixed stump and geo-textile, this paper comes to a conclusion about the analysis of the anti-corrosion test, revealing that among all of the common basal slop protection materials, mixed stump and fence are with Class II anti-corrosion property, while the geo-textile is with the first-class anti-corrosion property.

Effect of Ni on the corrosion resistance of bridge steel in a simulated hot and humid coastal-industrial atmosphere

The corrosion resistance of weathering bridge steels containing conventional contents of Ni(0.20 wt%, 0.42 wt%, 1.50 wt%) and a higher content of Ni(3.55 wt%) in a simulated hot and humid coastal-industrial atmosphere was investigated by corrosion depth loss, scanning electron microscopy–energy-dispersive X-ray spectroscopy, Raman spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and electrochemical methods. The results showed that, with increasing Ni content, the mechanical properties of the bridge steel were markedly improved, the welding parameters were satisfactory at room temperature, and the corrosion resistance was enhanced. When the Ni content was low(≤0.42 wt%), the crystallization process of the corrosion products was substantially promoted, enhancing the stability of the rust layer. When the Ni content was higher(~3.55 wt%), the corrosion reaction of the steel quickly reached a balance, because the initial rapid corrosion induced the formation of a protective rust layer in the early stage. Simultaneously, NiO and NiFe_2O_4 were generated in large quantities; they not only formed a stable, compact, and continuous oxide protective layer, but also strongly inhibited the transformation process of the corrosion products. This inhibition reduced the structural changes in the rust layer, thereby enhancing the protection. However, when the Ni content ranged from 0.42 wt% to 1.50 wt%, the corrosion resistance of the bridge steel increased only slightly.

Potential of four marine-derived fungi extracts as anti-proliferative and cell death-inducing agents in seven human cancer cell lines

Objective:To evaluate the in vitro anticancer activity of crude ethyl acetate extracts of the culture of four marine-derived fungi Aspergillus similanensis KUFA 0013(E1),Neosartorya paulistemis KUFC 7897(E2),Neosartorya siamensis KUFA 0017(E4) and Talaromyces trachyspermus KUFC 0021(E3) on a panel of seven human cancer cell lines.Methods:Effects on cell proliferation,induction of DNA damage and cell death were assessed by MTT and clonogenic assays,comet assay and nuclear condensation assay,respectively.Results:The proliferation of HepG2,HCTl 16 and A375 cells decreased after incubation with the extracts E2 and E4.The anti-proliterative effect was confirmed by morphologic alterations and by clonogenic assay.Both extracts also induced cell death in HepG2 and HCT116 cells.Doxorubicin was used as a positive control and showed in vitro anticancer activity.Conclusions:This study demonstrated,for the first time,that extracts of Neosartorya paulistensis and Neosartorya siamensis have selective anti-proliferative and cell death activities in HepG2,HCT16 and A375 cells.The bioactivity of these extracts suggests a potential for biotechnological applications and substantiates that both should be further considered for the elucidation of the molecular targets and signal transduction pathways involved.

Intravitreal anti-VEGF agents, oral glucocorticoids, and laser photocoagulation combination therapy for macular edema secondary to retinal vein occlusion: preliminary report

AIM： To evaluate the efficacy and safety of combined anti-vascular endothelial growth factor （VEGF） agents, oral glucocorticoid, and laser photocoagulation therapy for macular edema （ME） secondary to retinal vein occlusion （RVO）. METHODS： This study included 16 eyes of 16 patients with RVO-associated ME. Patients were initially treated with oral prednisone and an intravitreal anti-VEGF agent. Two weeks later, patients underwent standard laser photocoagulation. Best-corrected visual acuity （BCVA）, central retinal thickness （CRT）, and retinal vessel oxygenation were examined over 12mo. RESULTS： Patients received 1.43＋0.81 anti-VEGF injections. Mean baseline and 12-month IogMAR BCVA were 0.96±0.51 （20/178） and 0.31±0.88 （20/40）, respectively, in eyes with central retinal vein occlusion （CRVO） （P〈0.00）, and 1.02±0.45 （201209） and 0.60±0.49 （20/80）, respectively, in eyes with branch retinal vein occlusion （BRVO） （P〈0.00）. At 12mo, CRT had significantly decreased in eyes with CRVO （P〈0.00） and BRVO （P〈0.00）. Venous oxygen saturation had significantly increased in eyes with CRVO （P〈0.00） and BRVO （P〈0.00）. No examined parameters were significantly different between the 2 RVO groups. No serious adverse effects occurred. CONCLUSION： Anti-VEGF, glucocorticoid, and photocoagulation combination therapy improves visual outcome, prolongs therapeutic effect, and reduces the number of intravitreal injections in eyes with RVO- associated ME.

Clinical Study on Ganbi Decoction (肝痹汤) in Treating Antituberculotic Agent-Caused Liver Injury

Objective： To study the effect and mechanism of Ganbi decoction （GBD, 肝痹汤 ） in treating patients with antituberculotic agent caused liver injury （ATB-LI）. Methods： One hundred and twenty-eight patients with ATB-LI were randomly assigned to the treated group （ n = 66） and the control group （ n = 62） with the envelop method. Meanwhile, 60 healthy persons were selected as the healthy control group. The treated group was treated by GBD one dose every day with the constituents modified depending on patients＇ symp- toms, and the control group was treated with glucuronolactone tablets and inosine injection. One week was taken as one treatment course. The changes of clinical syndromes, physical signs, T-lymphycyte sub-groups and serum level of nitric oxide （NO） were observed before and after treatment and the recovery time of liver function was recorded. The outcome was compared with that in the healthy control group. Results： In the treated group, 28 patients （42.4%） were cured, 30 （45.5%） improved and 8 （ 12.1% ） ineffectively cured, the total effective rate being 87.9% （58/66）. In the control group, 17 patients （27.4%） were cured, 24 （38.7%） improved, and21 （33.9%）ineffectively cured, the total effective rate being 66.1% （41/62）. The total effective rate in the treated group was significantly higher than that in the control group （ P〈0. 05）. Liver function was improved in both groups, recovery time in the treated group was 12.0±7.0 days, which was significantly shorter than that in the control group （16.0±8.0 days）, showing significant difference between the two groups （ P〈0.05）. The levels of CD3, CD4 and CD8 were significantly higher and level of NO significantly lower in the two groups of patients than those in the healthy control group （ P〈0. 05）, but these parameters were improved more significantly in the treated group after treatment, when compared with those before treatment or with those in the control group, all showing significant difference （P〈0.05）. Conclusion： GBD could prevent ATB-LI, and its mechanism could be by way of reducing NO production induced by endotoxin of macrophage and stimulating the proliferation of T-lymphycyte to elevate immunity.

Effect of K1, K2 Anti-Bacterial Agents on Tobacco Ralstonia Solanacearum

The tobacco Ralstonia Solanacearum were both cultured on nutrient agar plates and inoculated in seedling stage of tobacco, then treated with K1 and K2, two anti-bacterial agents, at a serial con-centrations to study their inhibitory efficiency. The result indicated that K1 can inhibit R. Solanacearum growth entirely, at the concentration range from 1/50 to 1/5000. K2 can reach the same result at the concentration range from 1/50 to 1/50000. Compared with the control plates, K1, at the concentration 1/50000, had no significant differences, and the average number of colony per plate was 112-115. The immature tobacco shown wilt as soon as inoculated with R. Solanacearum, and recovered gradually after using K1, K2. The densities of microbial suspension, handled by K1, K2 within 10 hs, were both significantly lower than the controlled ones. The optical microscopy also shown that handled microbial body differed from the controlled, whose body was regular short, rod shape as opposed to the handled ones with irregular rod shape and damaged body. All the results indicated that K1 and K2 both had inhibitory effects on tobacco R. Solanacearum, and K2 was more efficient than K1.

Deposition of SiO_x on Metal Surface with a DBD Plasma Gun at Atmospheric Pressure for Corrosion Prevention

In this study, SiOx films were deposited by a dielectric barrier discharge （DBD） plasma gun at an atmospheric pressure. The relationship of the film structures with plasma powers was investigated by Fourier transform infrared spectroscopy （FTIR）, and scanning electron microscope （SEM）. It was shown that an uniform and cross-linking structure film was formed by the DBD gun. As an application, the SiOx films were deposited on a carbon steel surface for the anti-corrosion purpose. The experiment was carried out in a 0.1 M NaCl solution. It was found that a very good anti-corrosive property was obtained, i.e., the corrosion rate was decreased c.a. 15 times in 5% NaCl solution compared to the non-SiOx coated steel, as detected by the potentiodynamic polarization measurement.

Novel anti-diabetic agents in non-alcoholic fatty liver disease: a mini-review

BACKGROUND:Non-alcoholic fatty liver disease(NAFLD)encompasses a spectrum that ranges from simple steatosis to non-alcoholic steatohepatitis(NASH)and to cirrhosis.The recommended treatment for this disease includes measures that target obesity and insulin resistance.The present review summarizes the role of newer anti-diabetic agents in treatment of NAFLD.DATA SOURCES:PubMed,MEDLINE and Ovid databases were searched to identify human studies between January 1990and January 2013 using specified key words.Original studies that enrolled patients with a diagnosis of NAFLD or NASH and involved use of newer classes of anti-diabetic agents for a duration of at least 3 months were included.RESULTS:Out of the screened articles,four met eligibility criteria and were included in our review.The classes of newer anti-diabetic medications described were dipeptidyl peptidase IV inhibitors and glucagon-like peptide-1 analogues.CONCLUSIONS:Liraglutide and Exenatide showed improvement in transaminases as well as histology in patients with NASH.Sitagliptin showed improvement in transaminases but limited studies are there to access its effect on histology.Further studies are needed to support use of newer anti-diabetic medications in patients with NAFLD.

Improvement on Corrosion Resistance of Zirconia-Graphite Material for Powder Line of SEN

The influence of anti-oxidation additions and mi-crostructure characters of fused zirconia raw materials on the corrosion resistance of ZrO2-C were studied. The results show that BN addition can enhance the corrosion resistance of ZrO2-C due to the prevention of graphite oxidation, and zirconia raw material with good crystallization and densification will give better corrosion resistance by restrain the reaction between slag and zirconia.

Challenges and opportunities of using stereotactic body radiotherapy with anti-angiogenesis agents in tumor therapy

Microvessels promote proliferation of tumor cells by delivering oxygen and nutrients, but rapid growth of tumors results in unmet demands for oxygen and nutrients, thereby creating a hypoxia microenvironment. Under hypoxic conditions, vascular endothelial cells（ECs） initiate the formation of immature and abnormal microvasculature. This results in leakage and tortuosity that facilitates tumor cell invasion, metastasis and resistance to cytotoxic treatment.Radiotherapy（RT） is a vital tumor treatment modality. Currently, more than 60% of patients with malignant tumors receive RT at certain points during their treatment. Hypoxia induced by abnormal microvessels can hamper the cytotoxic effect of ionizing radiation, particularly, stereotactic body radiotherapy（SBRT）. Anti-angiogenesis（AA） agents are known to reduce and renormalize microvessels in tumors, and hence alleviate hypoxia. The combination of AA agents with SBRT may have a synergistic role in inhibiting the growth of tumors. On the contrary, large doses of irradiation may affect tumor microvessels itself. In this review, we aim to clarify the relationship between SBRT and microvessel formation in tumors. In addition, we provide a retrospective analysis of the combination therapy involving SBRT and AA agents in preclinical and clinical practice to define its role in antitumor treatment.