Study on Properties of Anti-Gas Channeling Lightweight Temperature-Resistant Latex Slurry

There is low formation pressure coefficient and high formation temperature in ludong-wucaiwan area. Gas cut and gas channeling happen seriously during oil and gas well cementing. The existing anti-migration additive has only effects on single trait, so it is difficult to meet cementing requirement. According to this situation we could use latex slurry to anti-gas channeling. We have synthesised a set of anti-gas channeling lightweight temperature-resistant latex slurry and formed a new channeling preventing latex slurry through plenty of previous laboratory experiments. Finally the performance of latex slurry on temperature-resistant, anti-gas channeling and the anti-gas channeling of cement paste are studied. The experimental results show that this latex system has strong temperature-resistant and anti-gas channeling, which completely meet the requirement of cementing in this area.

SEMI-BLIND CHANNEL ESTIMATION OF MULTIPLE-INPUT/MULTIPLE-OUTPUT SYSTEMS BASED ON MARKOV CHAIN MONTE CARLO METHODS

This paper addresses the issues of channel estimation in a Multiple-Input/Multiple-Output (MIMO) system. Markov Chain Monte Carlo (MCMC) method is employed to jointly estimate the Channel State Information (CSI) and the transmitted signals. The deduced algorithms can work well under circumstances of low Signal-to-Noise Ratio (SNR). Simulation results are presented to demonstrate their effectiveness.

Methods to Improve the Long Distance Time-Varying Channel Transmission Performance of Expendable Profiler

To improve the transmission performance of XCTD channel, this paper proposes a method to measure directly and fit the channel transmission characteristics by using frequency sweeping method. Sinusoidal signals with a frequency range of 100 Hz to 10 k Hz and an interval of 100 Hz are used to measure transmission characteristics of channels with lengths of 300 m, 800 m, 1300 m, and 1800 m. The correctness of the fitted channel characteristics by transmitting square wave, composite waves of different frequencies, and ASK modulation are verified. The results show that when the frequency of the signal is below 1500 Hz, the channel has very little effect on the signal. The signal compensated for amplitude and phase at the receiver is not as good as the uncompensated signal.Alternatively, when the signal frequency is above 1500 Hz, the channel distorts the signal. The quality of signal compensated for amplitude and phase at receiver is better than that of the uncompensated signal. Thus, we can select the appropriate frequency for XCTD system and the appropriate way to process the received signals. Signals below1500 Hz can be directly used at the receiving end. Signals above 1500 Hz are used after amplitude and phase compensation at the receiving end.

Effects of Numerical Methods on the Calculation of Developing Plane Channel Flow

In wall-bounded turbulent flow calculations, the past focus has been directed to the modelling of the Reynolds-stress gradients. Not much attention has been paid to the effects of the numerical methods used to calculate these terms and the modelled equations. Discrepancies between model calculations and measurements are quite often attributed to incorrect modelling, while the suitability and accuracy of the numerical methods used are seldom scrutinized. Instead, alternate near-wall and Reynolds-stress models are proposed to remedy the incorrect turbulent flow calculations. On the other hand, if care is not taken in the numerical treatment of the Reynolds-stress gradient terms, physically unrealistic results and solution instability could occur. Previous studies by the author and his collaborators on the effects of numerical methods have shown that some of the more commonly used numerical methods could enhance numerical stability in the solution procedure but would introduce considerable inaccuracy to the results. The flow cases chosen to demonstrate these inaccuracies are a backstep flow and flow in a square duct, where flow complexities are present. The current investigation attempts to show that the above-mentioned effects of numerical methods could also occur in the calculation of a developing plane channel flow, where flow complexities are absent. In addition, this study shows that the results thus obtained lead to a predicted skin friction coefficient that is influenced more by the numerical method used than by the turbulence model invoked. Together, these results show that numerical treatment of the Reynolds-stress gradients in the equations play an important role, even for a developing plane channel flow.

Partitioning characteristics of gas channel of coal-rock mass in mining space and gas orientation method

In order to research the influence of coal-rock mass morphology of mining space on the flow law of gas,the laboratory physical model and numerical computation methods were adopted to simulate coal mining activities.The simulation results indicate that,after coal seam mining,the loose rock accumulation body of free caving,ordered rock arrangement body of plate damage rich in longitudinal and transverse fractures and horizontal fissure body formed by rock mass deformation imbalance are formed from bottom to top in the mining space.For these three types of accumulation bodies,there are essential differences in the accumulation state,rock size and gas breakover characteristics.According to this,the coal-rock mass in the mining space is classified into gas turbulence channel area,gas transitional flow channel area and gas seepage channel area.In the turbulence channel area,the gas is distributed transversely and longitudinally and gas diffuses in the form of convection with Reynolds number R_e more than100;in the transitional flow channel area,one-way or two-way gas channels are crisscross and gas is of transitional flow regime with R,.between 10 and 100.In the seepage channel area,there are a few vertical gas channels with R,.less than 10.In this paper,the researches on the gas orientation method in different partitions were further carried out,gas orientation methods of low-level pipe burying,middle-level interception and high-level extraction were determined and an on-site industrial test was conducted,achieving the effective diversion of gas and verifying the reasonableness of gas channel partition.

Die structure optimization of equal channel angular extrusion for AZ31 magnesium alloy based on finite element method

Three-dimensional（3D） geometric models with different comer angles （90° and 120°） and with or without inner round fillets in the bottom die were designed. Some important process parameters were regarded as the calculation conditions used in DEFORMTM-3D software, such as stress--strain data of compression test for AZ31 magnesium, temperatures of die and billet, and friction coefficient. Influence of friction coefficient on deformation process was discussed. The results show that reasonable lubrication condition is important to plastic deformation. The change characteristics for distributions of effective stress and strain during an equal channel angular extrusion （ECAE） process with inner angle of 90° and without fillets at outer comer were described. Inhomogeneity index （C） was defined and deformation heterogeneity of ECAE was analyzed from the simulation and experiment results. The deformation homogeneity caused by fillets at outer comer increased compared with the die without fillets. The cumulated maximum strains decrease with increasing the fillets of outer comer in ECAE die and the inner comer angle. The analysis results show that better structures of ECAE die including appropriate outer comer fillet and the inner comer angle of 90° for the die can improve the strain and ensure plastic deformation homogenization to a certain extent. The required extrusion force drops with increasing the fillet made at outer comer in ECAE die. It is demonstrated that the prediction results are in good agreement with experiments and the theoretical calculation and the research conclusions in literatures.

SUBSPACE METHOD FOR BLIND IDENTIFICATION OF CDMA TIME-VARYING CHANNELS

A new blind method is proposed for identification of CDMA Time-Varying (TV)channels in this paper. By representing the TV channel's impulse responses in the delay-Doppler spread domain, the discrete-time canonical model of CDMA-TV systems is developed and a subspace method to identify blindly the Time-Invariant (TI) coordinates is proposed. Unlike existing basis expansion methods, this new algorithm does not require .estimation of the base frequencies, neither need the assumption of linearly varying delays across symbols. The algorithm offers definite explanation of the expansion coordinates. Simulation demonstrates the effectiveness of the algorithm.

A new method of characterizing equivalent strain for equal channel angular processing

In order to establish the quantitative relationship between equivalent strain and the performance index of the deformed material within the range of certain passes for equal channel angular processing （ECAP）, a new approach to characterize the equivalent strain was proposed. The results show that there exists better accordance between mechanical property （such as hardness or strength） and equivalent strain after rolling and ECAP in a certain range of deformation amount, and Gauss equation can be satisfied among the equivalent strain and the mechanical properties for ECAP. Through regression analysis on the data of hardness and strength after the deformation, a more generalized expression of equivalent strain for ECAP is proposed as：ε=k0exp[-（k1M-k2）^2], where M is the strength or hardness of the material, k1 is the modified coefficient （k1∈ （0, 1））, ko and k2 are two parameters dependent on the critical strain and mechanical property that reaches saturation state for the material, respectively. In this expression the equivalent strain for ECAP is characterized novelly through the mechanical parameter relating to material property rather than the classical geometry equation.

On the capability of the curvilinear immersed boundary method in predicting near-wall turbulence of turbulent channel flows

The immersed boundary method has been widely used for simulating flows over complex geometries.However,its accuracy in predicting the statistics of near-wall turbulence has not been fully tested.In this work,we evaluate the capability of the curvilinear immersed boundary(CURVIB)method in predicting near-wall velocity and pressure fluctuations in turbulent channel flows.Simulation results show that quantities including the time-averaged streamwise velocity,the rms(root-mean-square)of velocity fluctuations,the rms of vorticity fluctuations,the shear stresses,and the correlation coefficients of u'and v"computed from the CURVIB simulations are in good agreement with those from the body-fitted simulations.More importantly,it is found that the time-averaged pressure,the rms and wavenumber-frequency spectra of pressure fluctuations computed using the CURVIB method agree well with the body-fitted results.

Security Simulation of Continuous-Variable Quantum Key Distribution over Air-to-Water Channel Using Monte Carlo Method

Considering the ocean water＇s optical attenuation and the roughness of the sea surface, we analyze the security of continuous-variable （CV） quantum key distribution （QKD） based Mr-to-water channel. The effects of the absorp- tion and scattering on the transmittance of underwater quantum channel and the maximum secure transmission distance are studied. Considering the roughness of the sea surface, we simulate the performance bounds of CV QKD with different wind speeds using the Monte Carlo method. The results show that even if the secret key rate gradually reduces as the wind speed increases, the maximum transmission distance will not be affected obviously. Compared to the works regarding short-distance underwater optical communication, our research represents a significant step towards establishing secure communication between air platform and submarine vehicle.

Subspace-Based Blind Channel Estimation Method for MIMO-OFDM Systems

A subspace-based blind channel estination algo rithm for MIMO-OFDM systems is proposed. This algorithm exploits the cyclostationarity introduced by cyclic prefix of OFDM to estimate the channel parameters. The proposed new algorithm is found to be outperforming the other algorithm with respect to convergence rate and achievable mean square error and robustness to channel order over determination.

Investigation of nanofluid flow in a vertical channel considering polynomial boundary conditions by Akbari-Ganji’s method

In this research,a vertical channel containing a laminar and fully developed nanofluid flow is investigated.The channel surface’s boundary conditions for temperature and volume fraction functions are considered qth-order polynomials.The equations related to this problem have been extracted and then solved by the AGM and validated through the Runge-Kutta numerical method and another similar study.In the study,the effect of parameters,including Grashof number,Brownian motion parameter,etc.,on the motion,velocity,temperature,and volume fraction of nanofluids have been analyzed.The results demonstrate that increasing the Gr number by 100%will increase the velocity profile function by 78%and decrease the temperature and fraction profiles by 20.87%and 120.75%.Moreover,rising the Brownian motion parameter in five different sizes(0.1,0.2,0.3,0.4,and 0.5)causes lesser velocity,about 24.3%at first and 4.35%at the last level,and a maximum 52.86%increase for temperature and a 24.32%rise for ψ occurs when N b rises from 0.1 to 0.2.For all N_(t) values,at least 55.44%,18.69%,for F(η),andΩ(η),and 20.23%rise for ψ(η)function is observed.Furthermore,enlarging the N r parameter from 0.25 to 0.1 leads F(η)to rise by 199.7%,fluid dimensionless temperature,and dimensional volume fraction to decrease by 18%and 92.3%.In the end,a greater value of q means a more powerful energy source,amplifying all velocity,temperature,and volume fraction functions.The main novelty of this research is the combined convection qth-order polynomials boundary condition applied to the channel walls.Moreover,The AMG semi-analytical method is used as a novel method to solve the governing equations.

A Single Image Derain Method Based on Residue Channel Decomposition in Edge Computing

The numerous photos captured by low-price Internet of Things(IoT)sensors are frequently affected by meteorological factors,especially rainfall.It causes varying sizes of white streaks on the image,destroying the image texture and ruining the performance of the outdoor computer vision system.Existing methods utilise training with pairs of images,which is difficult to cover all scenes and leads to domain gaps.In addition,the network structures adopt deep learning to map rain images to rain-free images,failing to use prior knowledge effectively.To solve these problems,we introduce a single image derain model in edge computing that combines prior knowledge of rain patterns with the learning capability of the neural network.Specifically,the algorithm first uses Residue Channel Prior to filter out the rainfall textural features then it uses the Feature Fusion Module to fuse the original image with the background feature information.This results in a pre-processed image which is fed into Half Instance Net(HINet)to recover a high-quality rain-free image with a clear and accurate structure,and the model does not rely on any rainfall assumptions.Experimental results on synthetic and real-world datasets show that the average peak signal-to-noise ratio of the model decreases by 0.37 dB on the synthetic dataset and increases by 0.43 dB on the real-world dataset,demonstrating that a combined model reduces the gap between synthetic data and natural rain scenes,improves the generalization ability of the derain network,and alleviates the overfitting problem.

Energy response correction for an electronic personal dosimeter using the channel ratio method

An electronic personal dosimeter mainly uses a Si-PIN photodiode as X-and gamma-ray detectors.The photon energy response of this instrument is inconsistent in the case of no correction,which seriously affects the accurate monitoring of personal dose equivalent H_p(10)parameters for radiation workers.For this reason,in this paper we propose a method of combining composite screen detection technology,multichannel measurement technology,and the channel ratio method to achieve accurate measurement of the personal dose equivalent parameters.According to China National Standard GB/T 13161-2003 and National Verification Regulation JJG 1009-2006,the instrument was tested in the energy range between 48 keV and 1.25 MeV.The experimental results showed that the difference of energy response to ^(137)C_S corrected by the new method was almost constant within ±6.0%,which fulfilled the ±30% requirement of GB/T 13161-2003 and JJG1009-2006.Meanwhile,the method proposed obtained energy information regarding the radiation field.

Equal channel angular extrusion of NiTi shape memory alloy tube

As a new attempt, equal channel angular extrusion （ECAE） of nickel-titanium shape memory alloy （NiTi SMA） tube was investigated by means of process experiment, finite element method （FEM） and microscopy. NiTi SMA tube with the steel core in it was inserted into the steel can during ECAE of NiTi SMA tube. Based on rigid-viscoplastic FEM, multiple coupled boundary conditions and multiple constitutive models were used for finite element simulation of ECAE of NiTi SMA tube, where the effective stress field, the effective strain field and the velocity field were obtained. Finite element simulation results are in good accordance with the experimental ones. Finite element simulation results reveal that the velocity field shows the minimum value in the corner of NiTi SMA tube, where severe shear deformation occurs. Microstructural observation results reveal that severe plastic deformation leads to a certain grain orientation as well as occurrence of substructures in the grain interior and dynamic recovery occurs during ECAE of NiTi SMA tube. ECAE of NiTi SMA tube provides a new approach to manufacturing ultrafine-grained NiTi SMA tube.

Numerical Wave Channel with Absorbing Wave-Maker

The numerical wave channel has been developed based on the volume of fluid method (VOF) in conjunction with the Navier-Stokes equations. The absorbing wave-maker boundary on the left side of the channel is presented by prescribing velocity reference to linear wave-maker theory. The principle of which is that the numerical wave-maker is designed to move in a way that generates the required incident wave and cancels out any reflected wave that reach it at the same time. On the right side of the channel, the open boundary is set to permit incident waves to be transmitted freely. The parametric studies have been carried out at a range of ratios of water depth to wave length d/ L from 0.124 to 0.219, with wave height in the front of paddle/water depth ratio (H0 / d) from 0.1 to 0.3. Wave height, wave pressure distribution along the channel and velocity field are obtained for both open boundary condition and reflective boundary condition at the other end of the channel. For a reflective case, it is shown that the absorbing wave-maker is very effective in canceling out the reflected wave that reaches the numerical paddle and highly repeatable waves can be generated.

Study on resistance coefficient in compound channels

This paper presents a further study of the Manning and Darcy-Weisbach resistance coefficients, as they play a significant role in assessing the cross-sectional mean velocity, conveyance capacity and determining the lateral distribution of depth mean velocity and local boundary shear stress in compound channels. The relationships between the local, zonal and overall resistance coefficients, and a wide range of geometries and different roughness between the main channel and the flood plain are established by analyzing a vast amount of experimental data from a British Science and Engineering Research Council Flood Channel Facility （SERC-FCF）. And the experimental results also show that the overall Darcy-Weisbach resistance coefficient for a compound channel is the function of Reynolds number, but the function relationship is different from that for a single channel. By comparing and analyzing the conventional methods with the experimental data to predict composite roughness in compound channels, it is found that these methods are not suitable for compound channels. Moreover, the reason why the conventional methods cannot assess correctly the conveyance capacity of compound channels is also analyzed in this paper.

Control of reaction channels of CsI molecule by ultra-short laser pulse

The influence of the ultra-short pulse wavelength on the populations in the three electronic states of CsI molecule is investigated using the time-dependent wave packet method. The calculated results show that the populations in the two excited states approach to the maxima at the wavelengths of 369 nm and 297 nm, respectively. The photodissociation reaction channels of the CsI molecule can be chosen by controlling the pump pulse wavelength.

Comparative numerical study of single and two-phase models of nanofluid heat transfer in wavy channel

The main purpose of this study is to survey numerically comparison of two- phase and single phase of heat transfer and flow field of copper-water nanofluid in a wavy channel. The computational fluid dynamics （CFD） prediction is used for heat transfer and flow prediction of the single phase and three different two-phase models （mixture, volume of fluid （VOF）, and Eulerian）. The heat transfer coefficient, temperature, and velocity distributions are investigated. The results show that the differences between the temperature fie].d in the single phase and two-phase models are greater than those in the hydrodynamic tleld. Also, it is found that the heat transfer coefficient predicted by the single phase model is enhanced by increasing the volume fraction of nanoparticles for all Reynolds numbers; while for the two-phase models, when the Reynolds number is low, increasing the volume fraction of nanoparticles will enhance the heat transfer coefficient in the front and the middle of the wavy channel, but gradually decrease along the wavy channel.