IMAGING AND MTI PROCESSING BASED ON DUAL-FREQUENCIES DUAL-APERTURES SPACEBORNE SAR

Based on dual-frequencies dual-apertures spaceborne SAR （Synthetic Aperture Radar）, a new SAR system with four receiving channels and two operation modes is presented in this paper, SAR imaging and Moving Target Indication （MTI） are studied in this system. High resolution imaging with wide swath is implemented by the Mode Ⅰ, and MTI is completed by the Mode Ⅱ. High azimuth resolution is achieved by the Displaced Phase Center （DPC） multibeam technique. And the Coherent Accumulation （CA） method, which combines dual channels data of different carrier frequency, is used to enhance the range resolution. For the data of different carrier frequency, the two aperture interferometric processing is executed to implement clutter cancellation, respectively. And the couple of clutter suppressed data are employed to implement Dual Carrier Frequency Conjugate Processing （DCFCP）, then both slow and fast moving targets detection can be completed, followed by moving target imaging. The simulation results show the validity of the signal processing method of this new SAR system.

Extraordinary terahertz transmission through subwavelength spindle-like apertures in NbN film

We studied numerically the temperature dependent extraordinary terahertz transmission through niobium nitride(NbN) film perforated with subwavelength spindle-like apertures. Both the resonant frequency and intensity of extraordinary terahertz transmission peaks can be greatly modified by the transition of NbN film from the normal state to the superconducting state. An enhancement of the(±1, 0) NbN/magnesium oxide(MgO) peak intensity as high as 200% is demonstrated due to the combined contribution of both the superconducting transition and the excitation of localized surface plasmons(LSPs) around the apertures. The extraordinary terahertz transmission through spindle-like hole arrays patterned on the NbN film can pave the way for us to explore novel active tuning devices.

Role of localised surface plasmon polaritons coupling in optical transmission through double-layer metal apertures

In this paper, we investigate the optical properties of the double-layer metal films perforated with single apertures by analysing the coupling of localized surface plasmon polaritons （LSPPs）. It is found that the amplitude and the wavelength of transmission peak in such a structure can be adjusted by changing the longitudinal interval D between two films and the lateral displacements dx and dy which are parallel and perpendicular to the polarization direction of incident light, respectively. The variation of longitudinal interval D results in the redshift of transmission peak due to the change of coupling strength of LSPPs near the single apertures. The amplitude of transmission peak decreases with the increase of dy and is less than that in the case of dx, which originates from the difference in coupling manner between LSPPs and the localized natures of LSPPs.

Recognition of Direction of New Apertures from the Elongated Speckle Images: Simulation

In this paper, we present an elongated speckle images produced from diffusers using sharp elliptical apertures. The orientation of the elliptic aperture is recognized from the direction of the elongation in the speckle images. The aperture tilting out of the plane is investigated. Three models of elliptical apertures are considered and the corresponding speckle images are obtained. The 1st model is composed of two orthogonal ellipses or plus symbol pupil;the 2nd has four symmetric ellipses with an angle of 45° between each of them or in the form of a snow flake pupil and the 3rd model looks like an airplane. Also, the autocorrelation profiles of the speckle images corresponding to the diffused airplane are obtained from which the average speckle size is computed. Finally, the reconstructed images of the described elliptical models and its autocorrelation images, making use of Mat lab code, are obtained.

Computer Generated Quadratic and Higher Order Apertures and Its Application on Numerical Speckle Images

A computer generated quadratic and higher order apertures are constructed and the corresponding numerical speckle images are obtained. Secondly, the numerical images of the autocorrelation intensity of the randomly distributed object modulated by the apertures and the corresponding profiles are obtained. Finally, the point spread function (PSF) is computed for the described modulated apertures in order to improve the resolution.

A comparative study of stress influence on fracture apertures in fragmented rocks

This study compares the calculated fracture apertures in a fragmented rock layer under different stress scenarios using two different approaches. Approach 1 is a simplified method using a two-dimensional(2 D) mapping of the fracture network and projects the far-field stresses to individual fractures, and calculates the dilation, normal and shear displacements using experimental stiffnesses available in the literature. Approach 2 employs a three-dimensional(3 D) finite element method(FEM) for the mechanical analysis of the fragmented rock layer considering the interaction with the neighbouring rock layers, frictional interfaces between the rock blocks, stress variations within the fragmented rock layer,and displacements, rotations and deformations of rock blocks. After calculating the fracture apertures using either of the approaches, the permeability of the fragmented rock layer is calculated by running flow simulations using the updated fracture apertures. The comparison between the results demonstrates an example of the inaccuracies that may exist in methods that use simplified assumptions such as2 D modelling, ignoring the block rotations and displacements, projected far-field stresses on fractures,and the stress variations within the rock layer. It is found that for the cases considered here, the permeability results based on apertures obtained from the simplified approach could be 40 times different from the results from apertures calculated using a full mechanical approach. Hence, 3 D mechanical modelling implementing realistic boundary conditions, while considering the displacements and rotations of rock blocks, is suggested for the calculation of apertures in fragmented rocks.

CROSS-TRACK THREE APERTURES MILLIMETER WAVE SAR SIDE-LOOKING THREE-DIMENSIONAL IMAGING

The airborne cross-track three apertures MilliMeter Wave (MMW) Synthetic Aperture Radar (SAR) side-looking three-Dimensional (3D) imaging is investigated in this paper. Three apertures are distributed along the cross-track direction, and three virtual phase centers will be obtained through one-input and three-output. These three virtual phase centers form a sparse array which can be used to obtain the cross-track resolution. Because the cross-track array is short, the cross-track resolution is low. When the system works in side-looking mode, the cross-track resolution and height resolution will be coupling, and the low cross-track resolution will partly be transformed into the height uncertainty. The beam pattern of the real aperture is used as a weight to improve the Peak to SideLobe Ratio (PSLR) and Integrated SideLobe Ratio (ISLR) of the cross-track sparse array. In order to suppress the high cross-track sidelobes, a weighting preprocessing method is proposed. The 3D images of a point target and a simulation scene are achieved to verify the feasibility of the proposed method. And the imaging result of the real data obtained by the cross-track three-baseline MMW InSAR prototype is presented as a beneficial attempt.

Effect of stress-dependent microannulus aperture on well leakage

Debonding at the cement-casing interface is recognized as a principal failure mechanism leading to CO_(2) leakage in wells.This detachment gives rise to a microannulus,which notably possesses greater permeability than undamaged cement,undermining its sealing efficacy.Conventionally,the permeability of the microannulus is regarded as a uniform value throughout the well.However,fundamentally,a microannulus is one type of fracture,and its gap or aperture size is affected by the effective stress.In this work,we developed a unique experimental apparatus.This equipment facilitates the curing of cement inside a steel casing,the formation of a microannulus between the casing and the cement,and the investigation of the fluid flow dynamics along the microannulus under laboratory-replicated in situ conditions.The microannulus was formed by injecting fluid from one end of the setup,and receiving similar amount of fluid on the other end signified the development of the leakage channel.Additionally,strain gauges affixed to the casing’s external surface yielded key information on the microannulus’s opening and closure.We observed a noticeable decline in microannulus hydraulic aperture(or permeability)in relation to effective stress and an exponential equation fits their relationship.Our findings also indicate a distinct behavior when comparing liquid CO_(2) with water.Specifically,it is easier for liquid CO_(2) to create the microannulus.However,the hydraulic aperture range for this microannulus(0.7-6 mm)is considerably smaller than that created by water flow(2-17 mm).Finally,we integrated the stressdependent microannulus aperture size into the combined analysis of well mechanical integrity and well leakage.The outcomes consistently demonstrated that when factoring in the stress-dependent aperture sizes,the leakage rates are 3e5 times compared to a fixed aperture model.The traditional assumption of a constant aperture significantly underestimates fluid leakage risks.

A method to interpret fracture aperture of rock slope using adaptive shape and unmanned aerial vehicle multi-angle nap-of-the-object photogrammetry

The aperture of natural rock fractures significantly affects the deformation and strength properties of rock masses,as well as the hydrodynamic properties of fractured rock masses.The conventional measurement methods are inadequate for collecting data on high-steep rock slopes in complex mountainous regions.This study establishes a high-resolution three-dimensional model of a rock slope using unmanned aerial vehicle(UAV)multi-angle nap-of-the-object photogrammetry to obtain edge feature points of fractures.Fracture opening morphology is characterized using coordinate projection and transformation.Fracture central axis is determined using vertical measuring lines,allowing for the interpretation of aperture of adaptive fracture shape.The feasibility and reliability of the new method are verified at a construction site of a railway in southeast Tibet,China.The study shows that the fracture aperture has a significant interval effect and size effect.The optimal sampling length for fractures is approximately 0.5e1 m,and the optimal aperture interpretation results can be achieved when the measuring line spacing is 1%of the sampling length.Tensile fractures in the study area generally have larger apertures than shear fractures,and their tendency to increase with slope height is also greater than that of shear fractures.The aperture of tensile fractures is generally positively correlated with their trace length,while the correlation between the aperture of shear fractures and their trace length appears to be weak.Fractures of different orientations exhibit certain differences in their distribution of aperture,but generally follow the forms of normal,log-normal,and gamma distributions.This study provides essential data support for rock and slope stability evaluation,which is of significant practical importance.

Detection performance analysis for MIMO radar with distributed apertures in Gaussian colored noise

This paper establishes the classic linear model of signal of the MIMO radar system with distributed apertures. Based on this model, the design principle and detection performance of MIMO radar detector is investigated under conditions of Gaussian colored noise and partially correlated observation channels. First, the research on design principle of detector shows that the clutter suppression and matched filtering can be independently implemented at each receiving aperture, which greatly reduces the difficulty in implementation of these detectors. Based on these results, a Max detector is proposed for the case where partial channels are disabled due to strong noise and stealth techniques. The second part is the performance analysis of detector. The Fishier divergence coefficient and the statistical equivalent decomposition of limit statistics are used to theoretically analyze the detection performance of AMF detector, and then the analytical expressions of the detection performance of the AMF detector is derived. Analysis results show that both the colored nature of noise and the correlation among observation channels can reduce the capability of spatial diversity of the MIMO radar system, change the target RCSs among observation channels from quick fluctuation to slow fluctuation, and degenerate the detection performance of this radar system into that of the phased array radar system at high signal-to-noise ratio.

A photogrammetric approach for quantifying the evolution of rock joint void geometry under varying contact states

Accurate measurement of the evolution of rock joint void geometry is essential for comprehending the distribution characteristics of asperities responsible for shear and seepage behaviors.However,existing techniques often require specialized equipment and skilled operators,posing practical challenges.In this study,a cost-effective photogrammetric approach is proposed.Particularly,local coordinate systems are established to facilitate the alignment and precise quantification of the relative position between two halves of a rock joint.Push/pull tests are conducted on rock joints with varying roughness levels to induce different contact states.A high-precision laser scanner serves as a benchmark for evaluating the photogrammetry method.Despite certain deviations exist,the measured evolution of void geometry is generally consistent with the qualitative findings of previous studies.The photogrammetric measurements yield comparable accuracy to laser scanning,with maximum errors of 13.2%for aperture and 14.4%for void volume.Most joint matching coefficient(JMC)measurement errors are below 20%.Larger measurement errors occur primarily in highly mismatched rock joints with JMC values below 0.2,but even in cases where measurement errors exceed 80%,the maximum JMC error is only 0.0434.Thus,the proposed photogrammetric approach holds promise for widespread application in void geometry measurements in rock joints.

High-resolution photogrammetry to measure physical aperture of two separated rock fracture surfaces

Photogrammetry,reconstructing three-dimensional(3D)models from overlapping two-dimensional(2D)photos,finds application in rock mechanics and rock engineering to extract geometrical details of reconstructed objects,for example rock fractures.Fracture properties are important for determining the mechanical stability,permeability,strength,and shear behavior of the rock mass.Photogrammetry can be used to reconstruct detailed 3D models of two separated rock fracture surfaces to characterize fracture roughness and physical aperture,which controls the fluid flow,hydromechanical and shear behavior of the rock mass.This research aimed to determine the optimal number of scale bars required to produce high-precision 3D models of a fracture surface.A workflow has been developed to define the physical aperture of a fracture using photogrammetry.Three blocks of Kuru granite(25 cm×25 cm×10 cm)with an artificially induced fracture,were investigated.For scaling 3D models,321 markers were used as ground control points(GCPs)with predefined distances on each block.When the samples were wellmatched in their original positions,the entire block was photographed.Coordinate data of the GCPs were extracted from the 3D model of the blocks.Each half was surveyed separately and georeferenced by GCPs and merged into the same coordinate system.Two fracture surfaces were extracted from the 3D models and the vertical distance between the two surfaces was digitally calculated as physical aperture.Accuracy assessment of the photogrammetric reconstruction showed a 20-30 mm digital control distance accuracy when compared to known distances defined between markers.To attain this accuracy,the study found that at least 200 scale bars were required.Furthermore,photogrammetry was employed to measure changes in aperture under normal stresses.The results obtained from this approach were found to be in good agreement with those obtained using linear variable displacement transducers(LVDTs),with differences ranging from 1 mm to 8μm.

Deep-subwavelength single grooves prepared by femtosecond laser direct writing on Si

It is well known that femtosecond laser pulses can easily spontaneously induce deep-subwavelength periodic surface structures on transparent dielectrics but not on non-transparent semiconductors.Nevertheless,in this study,we demonstrate that using high-numerical-aperture 800 nm femtosecond laser direct writing with controlled pulse energy and scanning speed in the near-damage-threshold regime,polarization-dependent deep-subwavelength single grooves with linewidths of~180 nm can be controllably prepared on Si.Generally,the single-groove linewidth increases slightly with increase in the pulse energy and decrease in the scanning speed,whereas the single-groove depth significantly increases from~300 nm to~600 nm with decrease in the scanning speed,or even to over 1μm with multi-processing,indicating the characteristics of transverse clamping and longitudinal growth of such deep-subwavelength single grooves.Energy dispersive spectroscopy composition analysis of the near-groove region confirms that single-groove formation tends to be an ultrafast,non-thermal ablation process,and the oxidized deposits near the grooves are easy to clean up.Furthermore,the results,showing both the strong dependence of groove orientation on laser polarization and the occurrence of double-groove structures due to the interference of pre-formed orthogonal grooves,indicate that the extraordinary field enhancement of strong polarization sensitivity in the deep-subwavelength groove plays an important role in single-groove growth with high stability and collimation.

The 2023 M_(w)6.8 Adassil Earthquake(Chichaoua,Morocco)on a steep reverse fault in the deep crust and its geodynamic implications

The Mw 6.8 Adassil earthquake that occurred in the High Atlas on September 8,2023,was a catastrophic event that provided a rare opportunity to study the mechanics of deep crustal seismicity.This research aimed to decipher the rupture characteristics of the Adassil earthquake by analyzing teleseismic waveform data in conjunction with interferometric synthetic aperture radar(InSAR)observations from both ascending and descending orbits.Our analysis revealed a reverse fault mechanism with a centroid depth of approximately 28 km,exceeding the typical range for crustal earthquakes.This result suggests the presence of cooler temperatures in the lower crust,which facilitates the accumulation of tectonic stress.The earthquake exhibited a steep reverse mechanism,dipping at 70°,accompanied by minor strike-slip motion.Within the geotectonic framework of the High Atlas,known for its volcanic legacy and resulting thermal irregularities,we investigated the potential contributions of these factors to the initiation of the Adassil earthquake.Deep seismicity within the lower crust,away from plate boundaries,calls for extensive research to elucidate its implications for regional seismic hazard assessment.Our findings highlight the critical importance of studying and preparing for significant seismic events in similar geological settings,which would provide valuable insights into regional seismic hazard assessments and geodynamic paradigms.

Numerical Simulation of Slurry Diffusion in Fractured Rocks Considering a Time-Varying Viscosity

To analyze the effects of a time-varying viscosity on the penetration length of grouting,in this study cement slur-ries with varying water-cement ratios have been investigated using the Bingham’sfluidflow equation and a dis-crete element method.Afluid-solid coupling numerical model has been introduced accordingly,and its accuracy has been validated through comparison of theoretical and numerical solutions.For different fracture forms(a single fracture,a branch fracture,and a fracture network),the influence of the time-varying viscosity on the slurry length range has been investigated,considering the change in the fracture aperture.The results show that under different fracture forms and the same grouting process conditions,the influence of the time-varying viscosity on the seepage length is 0.350 m.

Synthetic Aperture Positioning: A Review

Obtaining precise position of interested emitters passively has wide applications in both civilian and military fields.Different from traditional parameter measurement and direct position determination(DPD)method,recently a new passive localization method based on synthetic aper-ture technique,named synthetic aperture positioning(SAP),has been proposed.The method com-pensates for the nonlinear phase produced by relative motion between the moving platform and the emitter,achieving coherent summation of intercepted signals.The SAP can obtain high-resolution and high-precision localization results at a low signal-to-noise ratio.This paper summarizes the research progress of SAP,including localization principles,spaceborne applications,and application scope analysis.Besides,the possible future outlook of SAP is considered.

An empirical method for joint inversion of wave and wind parameters based on SAR and wave spectrometer data

Synthetic aperture radar(SAR)and wave spectrometers,crucial in microwave remote sensing,play an essential role in monitoring sea surface wind and wave conditions.However,they face inherent limitations in observing sea surface phenomena.SAR systems,for instance,are hindered by an azimuth cut-off phenomenon in sea surface wind field observation.Wave spectrometers,while unaffected by the azimuth cutoff phenomenon,struggle with low azimuth resolution,impacting the capture of detailed wave and wind field data.This study utilizes SAR and surface wave investigation and monitoring(SWIM)data to initially extract key feature parameters,which are then prioritized using the extreme gradient boosting(XGBoost)algorithm.The research further addresses feature collinearity through a combined analysis of feature importance and correlation,leading to the development of an inversion model for wave and wind parameters based on XGBoost.A comparative analysis of this model with ERA5 reanalysis and buoy data for of significant wave height,mean wave period,wind direction,and wind speed reveals root mean square errors of 0.212 m,0.525 s,27.446°,and 1.092 m/s,compared to 0.314 m,0.888 s,27.698°,and 1.315 m/s from buoy data,respectively.These results demonstrate the model’s effective retrieval of wave and wind parameters.Finally,the model,incorporating altimeter and scatterometer data,is evaluated against SAR/SWIM single and dual payload inversion methods across different wind speeds.This comparison highlights the model’s superior inversion accuracy over other methods.

SAR regional all-azimuth observation orbit design for target 3D reconstruction

Three-dimensional(3D) synthetic aperture radar(SAR)extends the conventional 2D images into 3D features by several acquisitions in different aspects. Compared with 3D techniques via multiple observations in elevation, e.g. SAR interferometry(InSAR) and SAR tomography(TomoSAR), holographic SAR can retrieve 3D structure by observations in azimuth. This paper focuses on designing a novel type of orbit to achieve SAR regional all-azimuth observation(AAO) for embedded targets detection and holographic 3D reconstruction. The ground tracks of the AAO orbit separate the earth surface into grids. Target in these grids can be accessed with an azimuth angle span of360°, which is similar to the flight path of airborne circular SAR(CSAR). Inspired from the successive coverage orbits of optical sensors, several optimizations are made in the proposed method to ensure favorable grazing angles, the performance of 3D reconstruction, and long-term supervision for SAR sensors. Simulation experiments show the regional AAO can be completed within five hours. In addition, a second AAO of the same area can be duplicated in two days. Finally, an airborne SAR data process result is presented to illustrate the significance of AAO in 3D reconstruction.

High-Precision DOA Estimation Method Based on Synthetic Aperture Technique

The existing direction-of-arrival(DOA)estimation methods only utilize the current received signals,which are susceptible to noise.In this paper,a method for DOA estimation based on a motion platform is proposed to achieve high-precision DOA estimation by utilizing past and present signals.The concept of synthetic aperture is introduced to construct a linear DOA estima-tion model.A DOA fine-tuning method based on the linear model is proposed to eliminate the lin-ear DOA variation,achieving a non-coherent accumulation of DOA estimations.Moreover,the baseband modulation and the phase modulation caused by the range history are compensated to achieve the coherent accumulation of all the DOA estimations.Simulation results show that the proposed method can significantly improve the DOA estimated accuracy at low signal-to-noise ratios(SNR).

Modulated-ISRJ rejection using online dictionary learning for synthetic aperture radar imagery

In electromagnetic countermeasures circumstances,synthetic aperture radar(SAR)imagery usually suffers from severe quality degradation from modulated interrupt sampling repeater jamming(MISRJ),which usually owes considerable coherence with the SAR transmission waveform together with periodical modulation patterns.This paper develops an MISRJ suppression algorithm for SAR imagery with online dictionary learning.In the algorithm,the jamming modulation temporal properties are exploited with extracting and sorting MISRJ slices using fast-time autocorrelation.Online dictionary learning is followed to separate real signals from jamming slices.Under the learned representation,time-varying MISRJs are suppressed effectively.Both simulated and real-measured SAR data are also used to confirm advantages in suppressing time-varying MISRJs over traditional methods.