Transformation of long-period stacking ordered structures in Mg-Gd-Y-Zn alloys upon synergistic characterization of first-principles calculation and experiment and its effects on mechanical properties

Based on experiments and first-principles calculations,the microstructures and mechanical properties of as-cast and solution treated Mg-10Gd-4Y-xZn-0.6Zr(x=0,1,2,wt.%)alloys are investigated.The transformation process of long-period stacking ordered(LPSO)structure during solidification and heat treatment and its effect on the mechanical properties of experimental alloys are discussed.Results reveal that the stacking faults and 18R LPSO phases appear in the as-cast Mg-10Gd-4Y-1Zn-0.6Zr and Mg-10Gd-4Y-2Zn-0.6Zr alloys,respectively.After solution treatment,the stacking faults and 18R LPSO phase transform into 14H LPSO phase.The Enthalpies of formation and reaction energy of 14H and 18R LPSO are calculated based on first-principles.Results show that the alloying ability of 18R is stronger than that of 14H.The reaction energies show that the 14H LPSO phase is more stable than the 18R LPSO.The elastic properties of the 14H and 18R LPSO phases are also evaluated by first-principles calculations,and the results are in good agreement with the experimental results.The precipitation of LPSO phase improves the tensile strength,yield strength and elongation of the alloy.After solution treatment,the Mg-10Gd-4Y-2Zn-0.6Zr alloy has the best mechanical properties,and its ultimate tensile strength and yield strength are 278.7 MPa and 196.4 MPa,respectively.The elongation of Mg-10Gd-4Y-2Zn-0.6Zr reaches 15.1,which is higher than that of Mg-10Gd-4Y0.6Zr alloy.The improving mechanism of elastic modulus by the LPSO phases and the influence on the alloy mechanical properties are also analyzed.

A novel method for simulating nuclear explosion with chemical explosion to form an approximate plane wave: Field test and numerical simulation

A nuclear explosion in the rock mass medium can produce strong shock waves,seismic shocks,and other destructive effects,which can cause extreme damage to the underground protection infrastructures.With the increase in nuclear explosion power,underground protection engineering enabled by explosion-proof impact theory and technology ushered in a new challenge.This paper proposes to simulate nuclear explosion tests with on-site chemical explosion tests in the form of multi-hole explosions.First,the mechanism of using multi-hole simultaneous blasting to simulate a nuclear explosion to generate approximate plane waves was analyzed.The plane pressure curve at the vault of the underground protective tunnel under the action of the multi-hole simultaneous blasting was then obtained using the impact test in the rock mass at the site.According to the peak pressure at the vault plane,it was divided into three regions:the stress superposition region,the superposition region after surface reflection,and the approximate plane stress wave zone.A numerical simulation approach was developed using PFC and FLAC to study the peak particle velocity in the surrounding rock of the underground protective cave under the action of multi-hole blasting.The time-history curves of pressure and peak pressure partition obtained by the on-site multi-hole simultaneous blasting test and numerical simulation were compared and analyzed,to verify the correctness and rationality of the formation of an approximate plane wave in the simulated nuclear explosion.This comparison and analysis also provided a theoretical foundation and some research ideas for the ensuing study on the impact of a nuclear explosion.

Approximately Bi-Similar Symbolic Model for Discretetime Interconnected Switched System

Dear Editor,This letter concerns the development of approximately bi-similar symbolic models for a discrete-time interconnected switched system(DT-ISS).The DT-ISS under consideration is formed by connecting multiple switched systems known as component switched systems(CSSs).Although the problem of constructing approximately bi-similar symbolic models for DT-ISS has been addressed in some literature,the previous works have relied on the assumption that all the subsystems of CSSs are incrementally input-state stable.

Random Green's Function Method for Large-Scale Electronic Structure Calculation

We report a linear-scaling random Green's function(rGF) method for large-scale electronic structure calculation. In this method, the rGF is defined on a set of random states and is efficiently calculated by projecting onto Krylov subspace. With the rGF method, the Fermi–Dirac operator can be obtained directly, avoiding the polynomial expansion to Fermi–Dirac function. To demonstrate the applicability, we implement the rGF method with the density-functional tight-binding method. It is shown that the Krylov subspace can maintain at small size for materials with different gaps at zero temperature, including H_(2)O and Si clusters. We find with a simple deflation technique that the rGF self-consistent calculation of H_(2)O clusters at T = 0 K can reach an error of~ 1 me V per H_(2)O molecule in total energy, compared to deterministic calculations. The rGF method provides an effective stochastic method for large-scale electronic structure simulation.

Emerging perovskite materials for supercapacitors:Structure,synthesis,modification,advanced characterization,theoretical calculation and electrochemical performance

As a new generation electrode materials for energy storage,perovskites have attracted wide attention because of their unique crystal structure,reversible active sites,rich oxygen vacancies,and good stability.In this review,the design and engineering progress of perovskite materials for supercapacitors(SCs)in recent years is summarized.Specifically,the review will focus on four types of perovskites,perovskite oxides,halide perovskites,fluoride perovskites,and multi-perovskites,within the context of their intrinsic structure and corresponding electrochemical performance.A series of experimental variables,such as synthesis,crystal structure,and electrochemical reaction mechanism,will be carefully analyzed by combining various advanced characterization techniques and theoretical calculations.The applications of these materials as electrodes are then featured for various SCs.Finally,we look forward to the prospects and challenges of perovskite-type SCs electrodes,as well as the future research direction.

First Principles Calculations for Corrosion in Mg-Li-Al Alloys with Focus on Corrosion Resistance: A Comprehensive Review

This comprehensive review examines the structural,mechanical,electronic,and thermodynamic properties of Mg-Li-Al alloys,focusing on their corrosion resistance and mechanical performance enhancement.Utilizing first-principles calculations based on Density Functional Theory(DFT)and the quasi-harmonic approximation(QHA),the combined properties of the Mg-Li-Al phase are explored,revealing superior incompressibility,shear resistance,and stiffness compared to individual elements.The review highlights the brittleness of the alloy,supported by B/G ratios,Cauchy pressures,and Poisson’s ratios.Electronic structure analysis shows metallic behavior with varied covalent bonding characteristics,while Mulliken population analysis emphasizes significant electron transfer within the alloy.This paper also studied thermodynamic properties,including Debye temperature,heat capacity,enthalpy,free energy,and entropy,which are precisely examined,highlighting the Mg-Li-Al phase sensitive to thermal conductivity and thermal performance potential.Phonon density of states(PHDOS)confirms dynamic stability,while anisotropic sound velocities reveal elastic anisotropies.This comprehensive review not only consolidates the current understanding of the Mg-Li-Al alloy’s properties but also proposes innovative strategies for enhancing corrosion resistance.Among these strategies is the introduction of a corrosion barrier akin to the Mg-Li-Al network,which holds promise for advancing both the applications and performance of these alloys.This review serves as a crucial foundation for future research aimed at optimizing alloy design and processing methods.

Organic Compounds Possessing the Plastic Crystalline Phase: Calculation of Their Fusion Enthalpies

For the first time, for different organic and inorganic compounds possessing the plastic crystalline phase, a new semiempirical equation describing dependence of their fusion enthalpies on such physico-chemical quantities as normal melting temperature, surface tension, molar volume and critical molar volume is received on the base of the principle of corresponding states and the energy equipartition theorem. Moreover, the proposed equation allows one to take into account the particularities of one-particle molecular rotation in the plastic crystalline phase.

Utility and Application of a Versatile Analytical Method for MMF Calculation in AC Machines

A versatile analytical method(VAM) for calculating the harmonic components of the magnetomotive force(MMF) generated by diverse armature windings in AC machines has been proposed, and the versatility of this method has been established in early literature. However, its practical applications and significance in advancing the analysis of AC machines need further elaboration. This paper aims to complement VAM by augmenting its theory, offering additional insights into its conclusions, as well as demonstrating its utility in assessing armature windings and its application of calculating torque for permanent magnet synchronous machines(PMSM). This work contributes to advancing the analysis of AC machines and underscores the potential for improved design and performance optimization.

High-throughput calculation-based rational design of Fe-doped MoS_(2) nanosheets for electrocatalytic p H-universal overall water splitting

Electrocatalytic water splitting is crucial for H2generation via hydrogen evolution reaction(HER)but subject to the sluggish dynamics of oxygen evolution reaction(OER).In this work,single Fe atomdoped MoS_(2)nanosheets(SFe-DMNs)were prepared based on the high-throughput density functional theory(DFT)calculation screening.Due to the synergistic effect between Fe atom and MoS_(2)and optimized intermediate binding energy,the SFe-DMNs could deliver outstanding activity for both HER and OER.When assembled into a two-electrode electrolytic cell,the SFe-DMNs could achieve the current density of 50 mA cm^(-2)at a low cell voltage of 1.55 V under neutral condition.These results not only confirmed the effectiveness of high-throughput screening,but also revealed the excellent activity and thus the potential applications in fuel cells of SFe-DMNs.

Syntheses,crystal structures,and quantum chemistry calculation of two Ni(Ⅱ)coordination polymers

Two new coordination polymers,[Ni(Hpdc)(bib)(H_(2)O)]_(n)(1)and{[Ni(bib)_(3)](ClO_(4))_(2)}_(n)(2),were prepared by mixing Ni^(2+),3,5⁃pyrazoledicarboxylic acid(H3pdc)/p⁃nitrobenzoic acid and 1,4⁃bis(imidazol⁃1⁃ylmethyl)butane(bib)by a hydrothermal method,respectively.X⁃ray crystallography reveals a 2D network constructed by six⁃coordinated Ni(Ⅱ)centers,bib,and Hpdc2-ligands in complex 1,while a 2D network is built by Ni(Ⅱ)and bib ligands in 2.Furthermore,the quantum⁃chemical calculations have been performed on‘molecular fragments’extracted from the crystal structure of 1 using the PBE0/LANL2DZ method in Gaussian 16 and the VASP program.CCDC:2343794,1;2343798,2.

Partitioning Calculation Method of Short-Circuit Current for High Proportion DG Access to Distribution Network

Aiming at the problemthat the traditional short-circuit current calculationmethod is not applicable to Distributed Generation(DG)accessing the distribution network,the paper proposes a short-circuit current partitioning calculation method considering the degree of voltage drop at the grid-connected point of DG.Firstly,the output characteristics of DG in the process of low voltage ride through are analyzed,and the equivalent output model of DG in the fault state is obtained.Secondly,by studying the network voltage distribution law after fault in distribution networks under different DG penetration rates,the degree of voltage drop at the grid-connected point of DG is used as a partition index to partition the distribution network.Then,iterative computation is performed within each partition,and data are transferred between partitions through split nodes to realize the fast partition calculation of short-circuit current for high proportion DG access to distribution network,which solves the problems of long iteration time and large calculation error of traditional short-circuit current.Finally,a 62-node real distribution network model containing a high proportion of DG access is constructed onMATLAB/Simulink,and the simulation verifies the effectiveness of the short-circuit current partitioning calculation method proposed in the paper,and its calculation speed is improved by 48.35%compared with the global iteration method.

Temperature field calculation of rail flash welding

The forging stage of rail flash welding has a decisive influence on joint strength,and the study of the temperature distribution in the process has an important role in further improving joint strength.In this paper,three calculation methods for the temperature field are given.First,the finite element model of the temperature field before forging rail flash welding is established by using the transient heat module of Ansys software and verified by infrared temperature measurement.Second,the temperature distribution of different parts of the rail before flash welding is obtained by using infrared thermal imaging equipment.Third,Matlab software is used to calculate the temperature of the non-measured part.Finally,the temperature distribution function along the rail axis is fitted through the temperature measurement data.The temperature distribution before the top forging of the rail flash welding can be used to analyze the joint and heat-affected zone organization and properties effectively and to guide the parameter setting and industrial production.

Effect of Types and Orders of Electromagnetic Field Finite Element Meshes on Power Communication Harmonic Parameters Calculation Results of Tubular Hydrogenerators

In generator design field,waveform total harmonic distortion(THD)and telephone harmonic factor(THF)are parameters commonly used to measure the impact of generator no-load voltage harmonics on the power communication quality.Tubular hydrogenerators are considered the optimal generator for exploiting low-head,high-flow hydro resources,and they have seen increasingly widespread application in China's power systems recent years.However,owing to the compact and constrained internal space of such generators,their internal magnetic-field harmonics are pronounced.Therefore,accurate calculation of their THD and THF is crucial during the analysis and design stages to ensure the quality of power communication.Especially in the electromagnetic field finite element modeling analysis of such generators,the type and order of the finite element meshes may have a significant impact on the THD and THF calculation results,which warrants in-depth research.To address this,this study takes a real 34 MW large tubular hydrogenerator as an example,and establishes its electromagnetic field finite element model under no-load conditions.Two types of meshes,five mesh densities,and two mesh orders are analyzed to reveal the effect of electromagnetic field finite element mesh types and orders on the calculation results of THD and THF for such generators.

Density Functional Calculations of the Mechanical, Electronic and Dynamical Properties of Antiperovskite Ca3BO (B = Pb, Ge, Sn)

An analysis of mechanical, electronic and dynamical properties of antiperovskite Ca3BO (B = Pb, Ge, Sn) in cubic phase space group Pm-3m (221) has been studied using first principle density functional theory (DFT). Ground state energy computation was done using the Projector Augmented Wave (PAW) Pseudo Potentials and the Plane Wave (PW) basis set. The Generalized Gradient Approximation (GGA) was used for the exchange correlation. The open source code QUANTUM ESPRESSO (QE) was used in this study in which plane wave basis sets are applied for the expansion of the electronic structure wave function. Thermo_pw as a post-processing code was used for the computation of mechanical properties including bulk modulus and elastic constants with their derivatives. The lattice parameters are here calculated to be 4.87 Å, 4.86 Å and 4.84 Å for Ca3BO (B = Pb, Ge, Sn) respectively which compares well with other works. This also shows that the three crystals are similar in size and in most of their properties. In addition to this, projected density of states and band structure are also computed both showing that these materials are of semi-metallic nature and are stable in cubic phase. Phonon modes at gamma are also reported.

Velocity Form Calculations of Generalized Oscillator Strengths for 3s→ (3p, 4p, 5p, 6p) Dipole Transitions of Atomic Sodium in Debye Plasma

In this paper, the generalized oscillator strengths (GOSs) of excitations of atomic sodium from ground state to 2p63s0 (3p, 4p, 5p, 6p) states, immersed in Debye plasma, were calculated by using wavefunctions which were obtained numerically from the restricted Hartree-Fock (RHF) equation. This RHF equation employs the local density approach for exchange interactions including plasma Debye screening. Theoretical RHF and random phase approximation with exchange (RPAE) velocity calculations have shown that the GOSs for excitations to 3 s0(3 p,4 p,5 p,6 p)depend on the plasma Debye screening effects, as shown by the reduction in the GOS amplitude with decreasing Debye length λD. The agreement between the present RPAE V results for the transitions 3 s→3 s0(3 p,4 p,5 p)and the length calculations of Martínez-Flores was satisfactory. Correlation effects were found quite to be significant in the vicinity of the maxima of the GOS of the 3 s→3 s0(4 p,5 p,6 p)excitations by using the RPAE V approach. We note the poor influence of many electron correlations on the GOS of (3 s→3 p)transition with the same principal quantum number. Finally, we comment that the RPAE V calculations are useful in investigating electron correlation effects on the transition GOS of atomic sodium planted in Debye plasma. The present velocity results also reveal that the 3 s→3 s0(5p, 6p)transition GOSs tend to be delocalized due to more significant screening effects at Debye lengths λD=20and 30 a.u. for excited subshells 5p and 6p, respectively. We report here novel results of GOS for 3 s→3 s06ptransition obtained from different Debye lengths.

First-Principles Calculation of the Topological Nodal-Line Semimetal FeGe_(2)

The electronic and topological properties of FeGe2 with a tetragonal crystal structure were investigated via first-principles calculations.The results demonstrate that FeGe2 in this structure exhibits anti-ferromagnetism,with two bands crossing the Fermi level nesting each other at high-symmetry points in the Brillouin zone,forming a nodal ring where the nodes intersect in momentum space.Additionally,it possesses nontrivial topological surface states.Upon inclusion of SOC(spin-orbit coupling),there are no significant changes observed in the band structure,nodal features,or surface states,indicating the persistence of its topological nodal-line characteristics.

Financial Calculation Problems and Countermeasure Analysis of Large-Scale Engineering Construction Projects

The financial aspects of large-scale engineering construction projects profoundly influence their success.Strengthening cost control and establishing a scientific financial evaluation system can enhance the project’s economic benefits,minimize unnecessary costs,and provide decision-makers with a robust financial foundation.Additionally,implementing an effective cash flow control mechanism and conducting a comprehensive assessment of potential project risks can ensure financial stability and mitigate the risk of fund shortages.Developing a practical and feasible fundraising plan,along with stringent fund management practices,can prevent fund wastage and optimize fund utilization efficiency.These measures not only facilitate smooth project progression and improve project management efficiency but also enhance the project’s economic and social outcomes.

APPROXIMATE QUERY AND CALCULATION OF RNN_k BASED ON VORONOI CELL

Reverse k nearest neighbor （RNNk） is a generalization of the reverse nearest neighbor problem and receives increasing attention recently in the spatial data index and query. RNNk query is to retrieve all the data points which use a query point as one of their k nearest neighbors. To answer the RNNk of queries efficiently, the properties of the Voronoi cell and the space-dividing regions are applied. The RNNk of the given point can be found without computing its nearest neighbors every time by using the rank Voronoi cell. With the elementary RNNk query result, the candidate data points of reverse nearest neighbors can he further limited by the approximation with sweepline and the partial extension of query region Q. The approximate minimum average distance （AMAD） can be calculated by the approximate RNNk without the restriction of k. Experimental results indicate the efficiency and the effectiveness of the algorithm and the approximate method in three varied data distribution spaces. The approximate query and the calculation method with the high precision and the accurate recall are obtained by filtrating data and pruning the search space.

Research on Approximate Calculation of Preventive Maintenance Period in Machinery Systems under Random Distribution

Approximate calculation methods of prevention maintenance period under the random distribution are given,and three kinds of approximate calculation models of prevention maintenance period based on different security demands are come up with according to maintenance problems of machinery systems in modern enterprise and starting with different demands of systems. And then,how to make certain the best maintenance period by using the approximate calculation methods is illustrated by an exam- ple.

A Two-Stage Method for an Approximate Calculation of Statically Indeterminate Trusses

The paper presents the principles of a method, which in two simple stages makes possible to carry out the statically calculation of values of forces acting in the fiat static indeterminate trusses. In each stage, it is considered the static determinate truss, scheme of which is obtained after remove the suitable number of members from the basic static indeterminate truss. The both intermediate statically determinate trusses are of the same clear span and they are loaded by forces of half values applied to the corresponding truss nodes. The method applies one of the typical procedures of calculation of the statically determinate trusses and then it is applied in an appropriate way the rule of superposition for obtaining the final values of forces acting in particular members of the basic truss. The values of forces calculated in this way are of a very close approximation to the force values determined in the special and complex ways being considered as the exact calculation methods. The proposed method can be useful mostly but not only for the initial structural design of such systems. The simplicity of the two-stage method justifies an assumption that it can be relatively easy and worthy to adjust to the requirements of the computer aided technology of statically calculation of the complex forms of trusses.