Failure Characteristics of Rock-like Mortar Specimens with Arc-shaped Flaws under Freezing-thaw Cycles and Uniaxial Compression

To investigate the freeze-thaw(F-T)damages and failure characteristics of rock mass with arc-shaped joints in cold regions,three types of cement mortar specimens with different central angles and prefabricated arc-shaped flaws are subjected to uniaxial compressive tests under different F-T cycles.Experimental observations show that the uniaxial compressive strength of specimens are significantly influenced by F-T cycles and their failure modes are mainly affected by the central angleαof the prefabricated flaws.Unlike the specimens with a central angle of 60°,the specimens with a central angle of 120°and 180°have greater curvature of flaws,so tensile cracks occur in the arc-top area of their prefabricated flaws.According to experimental images observed by environmental scanning electron microscope(ESEM),as the number of F-T cycles increases,the deterioration effect of the specimen becomes more obvious,which is specifically reflected in the increase of the mass loss,peak stress loss,and damage variables as a power function,and the peak strain decreases as a quadratic polynomial.According to numerical results using two-dimensional particle flow code(PFC2D),it is found that F-T cycles cause more damage to the specimen in the early stages than in the later ones.The area of the concentrated compressive stress zone in the middle is decreased due to the increased number of F-T cycles,while the area of the surrounding tensile-shear stress zone is increased.The models appear different failure modes due to the release of concentrated stress in different tensile-shear zones.

The Origins of the Arc-Shaped Langshan Uplift and Linhe Trench

In the northern part of the Ordos Basin, there is a 325 km long arc-shaped Langshan uplift and a 15 km-deep Linhe Trench in front of Langshan, which are rare geological phenomena for which origins no one has explained. This article comprehensively analyzes the research achievements over the past 40 years of geology, geomorphology, seismic exploration, paleogeography, and oil and gas exploration in the Ordos Basin and Langshan. It recognizes that the northern part of the Ordos Basin experienced a meteorite impact in the Late Cretaceous period. The impact pushed the block northwest ward, subducting after colliding with igneous rocks in the north. This sudden event formed a clear arc-shaped mountain zone in the north and a wedge-shaped trench in front of the mountain. The chaotic layers, prolonged and continuous faults, and numerous thrust layers in the Langshan, a negative anomaly area in the center of the northern Ordos, abnormal orientation of crystalline basement structures in the north of Ordos, Moho uplift, and distribution of meteorite fragments in the northwest of Langshan, all of these geological phenomena support the occurrence of the meteorite impact event, forming the arc-shaped Langshan and the Trench.

ESMO2023:恩扎卢胺联合雄激素剥夺治疗对比安慰剂联合雄激素剥夺治疗在中国转移性激素敏感性前列腺癌患者中的疗效和安全性(中国ARCHES)

2019年发表的全球ARCHES试验(NCT02677896)结果显示,与安慰剂(placebo,PBO)+雄激素剥夺治疗(androgen deprivation therapy,ADT)相比,恩扎卢胺+ADT延长了转移性激素敏感性前列腺癌(metastatic hormone-sensitive prostate cancer,mHSPC)患者的总生存期和放射影像学无进展生存期(radiographic progression-free survival,rPFS)^([1])。然而,该试验无中国患者入组。欧洲肿瘤内科学会(European Society for Medical Oncology,ESMO)2023年会议报道了中国ARCHES研究(NCT04076059)的初步结果,这是一项评估恩扎卢胺+ADTvs.PBO+ADT在中国m HSPC患者中的疗效和安全性的多中心、随机、双盲、PBO对照的Ⅲ期试验^([2])。

Wave Diffraction on Arc-Shaped Floating Perforated Breakwaters

An analytical method is developed to study the sheltering effects on arc-shaped floating perforated breakwaters. In the process of analysis, the tloating breakwater is assumed to be rigid, thin, vertical, and immovable and located in water with constant depth. The fluid domain is divided into two regions by imaginary interface. The velocity potential in each region is expanded by eigenfunction in the context of linear theory. By satisfying continuity of pressure and normal velocity across the imaginary fluid interface, a set of linear algebraic equations can be obtained to determine the unknown coefficients for eigenfunction expansions. The accuracy of the present model was verified by a comparison with existing results for the case of arc-shaped floating breakwater. Numerical results, in the form of contour maps of the non-dimensional wave amplitude around the breakwater and diffracted wave amplitude at typical sections, are presented for a range of wave and breakwater parameters. Results show that the sheltering effects on the arc-shaped floating perforated breakwater are closely related to the incident wavelength, the draft and the porosity of the breakwater.

Numerical simulations of rip currents off arc-shaped coastlines

The rip currents induced by waves off arc-shaped coastlines are seriously harmful to humans, but understanding of their characteristics is lacking. In this study, the FUNWAVE model was used to calculate the wave-induced currents in the Haller experiment and the ideal arc-shaped coast similar to Sanya Dadonghai, Hainan Province,China. The results showed that the FUNWAVE model has considerable ability to simulate the rip currents, and it was used to further simulate rip currents off arc-shaped coastlines to investigate their characteristics. The rip currents were found to be stronger as the curvature of arc-shaped coastline increased. Coastal beach slope exerts a significant influence on rip currents; in particular, an overly steep or overly mild slope is not conducive to creating rip currents. Furthermore, the rip currents were found to become weaker as the size of arc-shaped coast decreased. When the height and period of waves increase, the strength of rip currents also increases, and, in some cases, wave heights of 0.4 m may produce dangerous rip currents.

Plastic Mechanism of Multi-pass Double-roller Clamping Spinning for Arc-shaped Surface Flange

Compared with the conventional single-roller spinning process, the double-roller clamping spinning（DRCS） process can effectively prevent the sheet metal surface wrinkling and improve the the production efficiency and the shape precision of final spun part. Based on ABAQUS/Explicit nonlinear finite element software, the finite element model of the multi-pass DRCS for the sheet metal is established, and the material model, the contact definition, the mesh generation, the loading trajectory and other key technical problems are solved. The simulations on the multi-pass DRCS of the ordinary Q235A steel cylindrical part with the arc-shaped surface flange are carried out. The effects of number of spinning passes on the production efficiency, the spinning moment, the shape error of the workpiece, and the wall thickness distribution of the final part are obtained. It is indicated definitely that with the increase of the number of spinning passes the geometrical precision of the spun part increases while the production efficiency reduces. Moreover, the variations of the spinning forces and the distributions of the stresses, strains, wall thickness during the multi-pass DRCS process are revealed. It is indicated that during the DRCS process the radical force is the largest, and the whole deformation area shows the tangential tensile strain and the radial compressive strain, while the thickness strain changes along the generatrix directions from the compressive strain on the outer edge of the flange to the tensile strain on the inner edge of the flange. Based on the G-CNC6135 NC lathe, the three-axis linkage computer-controlled experimental device for DRCS which is driven by the AC servo motor is developed. And then using the experimental device, the Q235A cylindrical parts with the arc-shape surface flange are formed by the DRCS. The simulation results of spun parts have good consistency with the experimental results, which verifies the feasibility of DRCS process and the reliability of the finite element model for DRCS.

Study on Submerged Upper Arc-Shaped Plate Type Breakwater

Based on the wave radiation and diffraction theory, this paper investigates a new type breakwater with upper arcshaped plate by using the boundary element method(BEM). By comparing with other three designs of plate type breakwater(lower arc-shaped plate, single horizontal plate and double horizontal plate), this new type breakwater has been proved more effective. The wave exiting force, transmission and reflection coefficients are analyzed and discussed. In order to reveal the wave elimination mechanism of this type of breakwater, the velocity field around the breakwater is obtained. It is shown that:(1) The sway exciting force is minimal.(2) When the ratio of the submergence and wave amplitude is 0.05, the wave elimination effect will increase by 50% compared with other three types of breakwater.(3) The obvious backflow is found above the plate in the velocity field analysis.

Coastline configuration and geomorphologic development mode of arc-shaped coast in South China

Coastline configuration indexes of 34 typical arc-shaped coasts in South China are investigated by the method of principal component analysis, and meanwhile deposition and geomorphologic features of arc-shaped coast are also analyzed. The results show: (1) The configuration of arc-shaped coast in South China is of the characteristic of variability and complexity. (2) The wave power and the openings of the bay are the decisive factors to result in the changes of the configuration of the arc-shaped coast in South China, however, incidence direction of the wave has no effect on configuration development of the coast. (3) Commonly, geomorphologic modes of the arc-shaped coast system in South China consist of barriers, lagoons and tidal-inlets, and can be divided into four types:the openings of the bay leaning to the east, the openings of the bay leaning to the south, the openings of the bay leaning to the west and the openings of the bay leaning to the north.

Numerical simulations of stress wave propagation and attenuation at arc-shaped interface inlayered SiC/Al composite

The effects of interface shape on stress wave distribution and attenuation were investiga- ted using finite element method （ FEM ）. The simulation results indicate that when the stress wave propagates from SiC ceramic to A1 alloy, the tensile stress decreases and the attenuation coefficient of the stress wave increases with increasing central angle of the concave interface between SiC and A1. But for the convex interface, the tensile stress increases and attenuation coefficient decreases with increasing central angle. As the stress wave propagates from A1 alloy to SiC ceramic, the atten- uation coefficient of stress wave decreases with increasing the central angle of the concave interface. For the convex interface, the attenuation coefficient increases with increasing central angle.

Hydrodynamic Performance of the Arc-Shaped Bottom-Mounted Breakwater

The problem of the hydrodynamic interaction with the arc-shaped bottom-mounted breakwaters is investigated theoretically. The breakwater is assumed to be rigid, thin, impermeable and vertically located in a finite water depth. The fluid domain is divided into two sub-regions of inner and outer by an auxiliary circular interface. Linear theory is assumed and the eigenfunction expansion approach is used to determine the wave field. In order to examine the validity of the theoretical model, the analytical solutions are compared to agree well with published results with the same parameters. Numerical results including wave amplitude, surge pressure, and wave force are presented with different model parameters. The major factors including wave parameters, structure configuration, and water depth that affect the surge pressure, wave forces, and wave amplitudes are discussed and illustrated by some graphs and cloud maps.

A DECAGONAL QUASICRYSTAL WITH AN ARC-SHAPED CRACK

A decagonal quasicrystal, which is weakened by an arc-shaped crackpenetrating through the solid in the period direction, and which is subjected to remote uniformphonon stresses, is investigated by applying the complex variable method which is just developed bythe authors. It is found that the phonon and phason stresses near the crack tips exhibit inversesquare root singularities. The four complex stress functions characterizing the phonon and phasonfields are derived. Explicit expressions for the phonon and phason stress intensity factors, crackopening displacements and energy release rate are also presented.

Determination of Wind Pressure Coefficients for Arc-Shaped Canopy Roof with Numerical Wind Tunnel Method

In this paper,the wind load on an arc-shaped canopy roof was studied with numerical wind tunnel method(NWTM) .Three-dimensional models were set up for the canopy roof with opened or closed skylights.The air flow around the roof under wind action from three directions was analysed respectively.Wind pressure coefficients on the canopy roof were determined by NWTM.The results of NWTM agreed well with those of wind tunnel test for the roof with opened skylights,which verified the applicability and rationality of NWTM.The effect of the closure of skylights was then investigated with NWTM.It was concluded that the closure of the skylights may increase the wind suction on the top surface of the roof greatly and should be considered in the structure design of the canopy roof.

Health diagnosis of ultrahigh arch dam performance using heterogeneous spatial panel vector model

Currently,more than ten ultrahigh arch dams have been constructed or are being constructed in China.Safety control is essential to long-term operation of these dams.This study employed the flexibility coefficient and plastic complementary energy norm to assess the structural safety of arch dams.A comprehensive analysis was conducted,focusing on differences among conventional methods in characterizing the structural behavior of the Xiaowan arch dam in China.Subsequently,the spatiotemporal characteristics of the measured performance of the Xiaowan dam were explored,including periodicity,convergence,and time-effect characteristics.These findings revealed the governing mechanism of main factors.Furthermore,a heterogeneous spatial panel vector model was developed,considering both common factors and specific factors affecting the safety and performance of arch dams.This model aims to comprehensively illustrate spatial heterogeneity between the entire structure and local regions,introducing a specific effect quantity to characterize local deformation differences.Ultimately,the proposed model was applied to the Xiaowan arch dam,accurately quantifying the spatiotemporal heterogeneity of dam performance.Additionally,the spatiotemporal distri-bution characteristics of environmental load effects on different parts of the dam were reasonably interpreted.Validation of the model prediction enhances its credibility,leading to the formulation of health diagnosis criteria for future long-term operation of the Xiaowan dam.The findings not only enhance the predictive ability and timely control of ultrahigh arch dams'performance but also provide a crucial basis for assessing the effectiveness of engineering treatment measures.

Recent Construction Technology Innovations and Practices for Large-Span Arch Bridges in China

Arch bridges provide significant technical and economic benefits under suitable conditions.In particular,concrete-filled steel tubular(CFST)arch bridges and steel-reinforced concrete(SRC)arch bridges are two types of arch bridges that have gained great economic competitiveness and span growth potential due to advancements in construction technology,engineering materials,and construction equipment over the past 30 years.Under the leadership of the author,two record-breaking arch bridges—that is,the Pingnan Third Bridge(a CFST arch bridge),with a span of 560 m,and the Tian’e Longtan Bridge(an SRC arch bridge),with a span of 600 m—have been built in the past five years,embodying great technological breakthroughs in the construction of these two types of arch bridges.This paper takes these two arch bridges as examples to systematically summarize the latest technological innovations and practices in the construction of CFST arch bridges and SRC arch bridges in China.The technological innovations of CFST arch bridges include cable-stayed fastening-hanging cantilevered assembly methods,new in-tube concrete materials,in-tube concrete pouring techniques,a novel thrust abutment foundation for nonrocky terrain,and measures to reduce the quantity of temporary facilities.The technological innovations of SRC arch bridges involve arch skeleton stiffness selection,the development of encasing concrete materials,encasing concrete pouring,arch rib stress mitigation,and longitudinal reinforcement optimization.To conclude,future research focuses and development directions for these two types of arch bridges are proposed.

Numerical Simulation Analysis of Welded Joints in Arch Ribs of Large Span Steel Pipe Arch Bridges

In order to study the residual stress distribution law of welded joints of arch ribs of large-span steel pipe concrete arch bridges,numerical simulation of temperature,stress and strain fields based on ABAQUS for welded joints of arch-ribbed steel tubes using 7-,8-and 9-layer welds is carried out and its accuracy is demonstrated.The steel pipe welding temperature changes,residual stress distribution,different processes residual stress changes in the law,the prediction of post-weld residual stress distribution and deformation are studied in this paper.The results show that the temperature field values and test results are more consistent with the accuracy of numerical simulation of welding,the welding process is mainly in the form of heat transfer;Residual high stresses are predominantly distributed in the Fusion zone(FZ)and Heat-affected zone(HAZ),with residual stress levels tending to decrease from the center of the weld along the axial path,the maximum stress appears in the FZ and HAZ junction;The number of welding layers has an effect on the residual stress distribution,the number of welding layers increases,the residual stress tends to decrease,while the FZ and HAZ high stress area range shrinks;Increasing the number of plies will increase the amount of residual distortion.

中国汽油价格波动基于ARCH模型的分析研究

本文采用ARCH模型,并使用Eviews10统计学软件,利用2014年到2024年近11年的92号汽油价格,分析中国汽油市场价格的波动性。通过分析北京、上海、广州三个地区的92号汽油价格,表明中国汽油价格残差序列具有明显的“尖峰厚尾”特征,也具有显著的波动性特性。同时也印证了ARCH模型能够很好地描述中国汽油价格市场的波动性特性。本文最后根据实证分析结果,对中国应积极应对国际油价的变化,提出可操作性建议。

A Nonlinear Explicit Model of A Non-Circular Subsea Tunnel-Liner System with An FGM Inverted Arch Under Mechanical Loading and Fire Fields

This paper proposes an explicit scheme to analyze the failure of a subsea polyhedral tunnel-liner system with an inverted arch under mechanical loading and fire fields.The thin-walled liner is made of Functionally Graded Materials(FGMs),which may improve the stability behavior of the tunnel-liner system.Hydrostatic pressure is inevitable in the liner since underground water may penetrate the cracks of the tunnel,and reach the outer surface of the liner.In addition,an elevated temperature loading is taken into account,considering that fire may occur in the tunnel-liner system.Under the combination of mechanical loading and thermal loading,the liner deforms into a single-lobe shape,which is depicted by a trigonometric function.The total potential energy is expressed quantitatively after the energy approach and thin-walled shell theory are used.The minimum potential energy is obtained when the critical buckling occurs.The critical buckling pressure is calculated,which considers the effect of the thermal field.The present analytical prediction is subsequently compared precisely with other closed-form solutions.Finally,the effects of several parameters,such as the geometric shapes,temperature variations,and volume fraction indices,are discussed to further survey the buckling performance of the nonlinear buckling of an FGM polyhedral liner with an inverted arch.One may address a polyhedral liner with fewer polyhedral sides,and a lower volume fraction index is recommended to rehabilitate cracked tunnels in engineering applications.

Prediction model of surrounding rock deformation in doublecontinuous-arch tunnel based on the ABC-WNN

Purpose–The wavelet neural network(WNN)has the drawbacks of slow convergence speed and easy falling into local optima in data prediction.Although the artificial bee colony(ABC)algorithm has strong global optimization ability and fast convergence speed,it also has the drawbacks of slow speed while finding the optimal solution and weak optimization ability in the later stage.Design/methodology/approach–This article uses an ABC algorithm to optimize the WNN and establishes an ABC-WNN analysis model.Based on the example of the Jinan Yuhan underground tunnel project,the deformation of the surrounding rock of the double-arch tunnel crossing the fault fracture zone is predicted and analyzed,and the analysis results are compared with the actual detection amount.Findings–The comparison results show that the predicted values of the ABC-WNN model have a high degree of fitting with the actual engineering data,with a maximum relative error of only 4.73%.On this basis,the results show that the statistical features of ABC-WNN are the lowest,with the errors at 0.566 and 0.573,compared with the single back propagation(BP)neural network model and WNN model.Therefore,it can be derived that the ABC-WNN model has higher prediction accuracy,better computational stability and faster convergence speed for deformation.Originality/value–This article uses firstly the ABC-WNN for the deformation analysis of double-arch tunnels.This attempt laid the foundation for artificial intelligence prediction in deformation analysis of multiarch tunnels and small clearance tunnels.It can provide a new and effective way for deformation prediction in similar projects.

Effects of comprehensive nursing with cognitive behavioral therapy in orthodontic osteodilated arch treatment

BACKGROUND This work explored the effects of cognitive behavior therapy(CBT)-based comprehensive nursing intervention(CNI)mode in arch expansion to treat patients with orthodontic osteodilated arch(OOA).AIM To explore the application effect of CBT-based CNI model in orthodontic expansion arch treatment.METHODS Using convenient sampling method,81 patients with OOA were selected and rolled into a control group(Ctrl group,40 cases)and an observation group(Obs group,41 cases).During the treatment,patients in the Ctrl group received routine nursing intervention mode,and the those in the Obs group received CBT mode on the basis of this.Before and after intervention,the incidence of oral mucositis,the mastery rate of correct arch expansion method,self-rating anxiety scale score,soft scale index,and plaque index were compared for patients in different groups.In addition,satisfaction and complications were comparatively analyzed.RESULTS Incidence of oral mucositis in the Obs group was lower(14.6%vs 38.5%),and the mastery rate of correct arch expansion method was obviously higher(90.2%vs 55.0%)was obviously higher(all P<0.05).Meanwhile,the soft scale index and plaque index in the Obs group were much lower(P<0.05).The compliance(90.24%)and satisfaction(95.12%)in the Obs group were greatly higher(P<0.05).CONCLUSION The CBT-based CNI mode greatly improved the mastery rate of correct arch expansion method during arch expansion in treating patients with OOA and enhanced the therapeutic effect of arch expansion and the oral health of patients,improving the patient compliance.

基于SARIMA-ARCH的电量预测模型

电量预测是供电单位购电的重要依据,是电力经济稳定运行的根本基础。提出采用SARIMA-ARCH融合模型对某地区售电量进行预测。首先,采用季节时间序列分析方法(SARIMA)对月度电量时间序列进行建模,通过ACF和PACF图筛选确定出最佳模型阶数,得到季节性时间序列模型(SARIMA)基础预测模型;提取模型残差的波动性,建立自回归条件异方差(ARCH)模型;最后,将SARIMA-ARCH模型与常规SRIAM和ARIMA的预测值进行对比分析。结果表明,SARIMAARCH混合模型的预测精度较高。