A Joint Activity and Data Detection Scheme for Asynchronous Grant-Free Rateless Multiple Access

This paper considers the frameasynchronous grant-free rateless multiple access(FAGF-RMA)scenario,where users can initiate access at any symbol time,using shared channel resources to transmit data to the base station.Rateless coding is introduced to enhance the reliability of the system.Previous literature has shown that FA-GFRMA can achieve lower access delay than framesynchronous grant-free rateless multiple access(FSGF-RMA),with extreme reliability enabled by rateless coding.To support FA-GF-RMA in more practical scenarios,a joint activity and data detection(JADD)scheme is proposed.Exploiting the feature of sporadic traffic,approximate message passing(AMP)is exploited for transmission signal matrix estimation.Then,to determine the packet start points,a maximum posterior probability(MAP)estimation problem is solved based on the recovered transmitted signals,leveraging the intrinsic power pattern in the codeword.An iterative power-pattern-aided AMP algorithm is devised to enhance the estimation performance of AMP.Simulation results verify that the proposed solution achieves a delay performance that is comparable to the performance limit of FA-GF-RMA.

Interpolated Bumpless Transfer Control for Asynchronously Switched Linear Systems

This paper revisits the problem of bumpless transfer control(BTC) for discrete-time nondeterministic switched linear systems. The general case of asynchronous switching is considered for the first time in the field of BTC for switched systems. A new approach called interpolated bumpless transfer control(IBTC) is proposed, where the bumpless transfer controllers are formulated with the combination of the two adjacent modedependent controller gains, and are interpolated for finite steps once the switching is detected. In contrast with the existing approaches, IBTC does not necessarily run through the full interval of subsystems, as well as possesses the time-varying controller gains(with more flexibility and less conservatism) achieved from a control synthesis allowing for the stability and other performance of the whole switched system. Sufficient conditions ensuring stability and H_(∞) performance of the underlying system by IBTC are developed, and numerical examples verify the theoretical findings.

Anti-Byzantine Attacks Enabled Vehicle Selection for Asynchronous Federated Learning in Vehicular Edge Computing

In vehicle edge computing(VEC),asynchronous federated learning(AFL)is used,where the edge receives a local model and updates the global model,effectively reducing the global aggregation latency.Due to different amounts of local data,computing capabilities and locations of the vehicles,renewing the global model with same weight is inappropriate.The above factors will affect the local calculation time and upload time of the local model,and the vehicle may also be affected by Byzantine attacks,leading to the deterioration of the vehicle data.However,based on deep reinforcement learning(DRL),we can consider these factors comprehensively to eliminate vehicles with poor performance as much as possible and exclude vehicles that have suffered Byzantine attacks before AFL.At the same time,when aggregating AFL,we can focus on those vehicles with better performance to improve the accuracy and safety of the system.In this paper,we proposed a vehicle selection scheme based on DRL in VEC.In this scheme,vehicle’s mobility,channel conditions with temporal variations,computational resources with temporal variations,different data amount,transmission channel status of vehicles as well as Byzantine attacks were taken into account.Simulation results show that the proposed scheme effectively improves the safety and accuracy of the global model.

Asynchronous Learning-Based Output Feedback Sliding Mode Control for Semi-Markov Jump Systems: A Descriptor Approach

This paper presents an asynchronous output-feed-back control strategy of semi-Markovian systems via sliding mode-based learning technique.Compared with most literature results that require exact prior knowledge of system state and mode information,an asynchronous output-feedback sliding sur-face is adopted in the case of incompletely available state and non-synchronization phenomenon.The holonomic dynamics of the sliding mode are characterized by a descriptor system in which the switching surface is regarded as the fast subsystem and the system dynamics are viewed as the slow subsystem.Based upon the co-occurrence of two subsystems,the sufficient stochastic admissibility criterion of the holonomic dynamics is derived by utilizing the characteristics of cumulative distribution functions.Furthermore,a recursive learning controller is formulated to guarantee the reachability of the sliding manifold and realize the chattering reduction of the asynchronous switching and sliding motion.Finally,the proposed theoretical method is substantia-ted through two numerical simulations with the practical contin-uous stirred tank reactor and F-404 aircraft engine model,respectively.

Review on the Usage of Synchronous and Asynchronous FIFOs in Digital Systems Design

First-Input-First-Output (FIFO) buffers are extensively used in contemporary digital processors and System-on-Chips (SoC). There are synchronous FIFOs and asycnrhonous FIFOs. And different sized FIFOs should be implemented in different ways. FIFOs are used not only for the pipeline design within a processor, for the inter-processor communication networks, for example Network-on-Chips (NoCs), but also for the peripherals and the clock domain crossing at the whole SoC level. In this paper, we review the interface, the circuit implementation, and the various usages of FIFOs in various levels of the digital design. We can find that the usage of FIFOs could greatly facilitate the signal storage, signal decoupling, signal transfer, power domain separation and power domain crossing in digital systems. We hope that more attentions are paid to the usages of synchronous and asynchronous FIFOs and more sophististicated usages are discovered by the digital design communities.

Harmonics in the Squirrel Cage Induction Motor Analytic Calculation-Part Ⅰ: Differential Leakage, Attenuation, Asynchronous Parasitic Torques

The magnetic field generated in the air gap of the cage asynchronous machine and the harmonics of the magnetomotive forces creating that magnetic field, as well as the related differential leakage, attenuation, asynchronous parasitic torques have been discussed in great detail in the literature, but always separately, for a long time. However, systematization of the phenomenon still awaits. Therefore, it is worth summarizing the completeness of the phenomena in a single study – with a new approach at the same time-in order to reveal the relationships between them. The role of rotor slot number is emphasized much more than before. An existing, commonly used, but still impractical basic figure has been modified to more clearly demonstrate the response of the rotor for the harmonics of the stator. The need to treat differential leakage, asynchronous parasitic torques and attenuation together will be demonstrated: new formula for asynchronous parasitic torque is derived;the long-used characteristic curves for differential leakage and attenuation used separately so far was merged into one, correct curve in order to provide a correct design guide for the engineers.

Inference of interactions between players based on asynchronously updated evolutionary game data

The interactions between players of the prisoner's dilemma game are inferred using observed game data.All participants play the game with their counterparts and gain corresponding rewards during each round of the game.The strategies of each player are updated asynchronously during the game.Two inference methods of the interactions between players are derived with naive mean-field(n MF)approximation and maximum log-likelihood estimation(MLE),respectively.Two methods are tested numerically also for fully connected asymmetric Sherrington-Kirkpatrick models,varying the data length,asymmetric degree,payoff,and system noise(coupling strength).We find that the mean square error of reconstruction for the MLE method is inversely proportional to the data length and typically half(benefit from the extra information of update times)of that by n MF.Both methods are robust to the asymmetric degree but work better for large payoffs.Compared with MLE,n MF is more sensitive to the strength of couplings and prefers weak couplings.

Fully asynchronous distributed optimization with linear convergence over directed networks

We study distributed optimization problems over a directed network,where nodes aim to minimize the sum of local objective functions via directed communications with neighbors.Many algorithms are designed to solve it for synchronized or randomly activated implementation,which may create deadlocks in practice.In sharp contrast,we propose a fully asynchronous push-pull gradient(APPG) algorithm,where each node updates without waiting for any other node by using possibly delayed information from neighbors.Then,we construct two novel augmented networks to analyze asynchrony and delays,and quantify its convergence rate from the worst-case point of view.Particularly,all nodes of APPG converge to the same optimal solution at a linear rate of O(λ^(k)) if local functions have Lipschitz-continuous gradients and their sum satisfies the Polyak-?ojasiewicz condition(convexity is not required),where λ ∈(0,1) is explicitly given and the virtual counter k increases by one when any node updates.Finally,the advantage of APPG over the synchronous counterpart and its linear speedup efficiency are numerically validated via a logistic regression problem.

A Secure and Effective Energy-Aware Fixed-Point Quantization Scheme for Asynchronous Federated Learning

Asynchronous federated learning(AsynFL)can effectivelymitigate the impact of heterogeneity of edge nodes on joint training while satisfying participant user privacy protection and data security.However,the frequent exchange of massive data can lead to excess communication overhead between edge and central nodes regardless of whether the federated learning(FL)algorithm uses synchronous or asynchronous aggregation.Therefore,there is an urgent need for a method that can simultaneously take into account device heterogeneity and edge node energy consumption reduction.This paper proposes a novel Fixed-point Asynchronous Federated Learning(FixedAsynFL)algorithm,which could mitigate the resource consumption caused by frequent data communication while alleviating the effect of device heterogeneity.FixedAsynFL uses fixed-point quantization to compress the local and global models in AsynFL.In order to balance energy consumption and learning accuracy,this paper proposed a quantization scale selection mechanism.This paper examines the mathematical relationship between the quantization scale and energy consumption of the computation/communication process in the FixedAsynFL.Based on considering the upper bound of quantization noise,this paper optimizes the quantization scale by minimizing communication and computation consumption.This paper performs pertinent experiments on the MNIST dataset with several edge nodes of different computing efficiency.The results show that the FixedAsynFL algorithm with an 8-bit quantization can significantly reduce the communication data size by 81.3%and save the computation energy in the training phase by 74.9%without significant loss of accuracy.According to the experimental results,we can see that the proposed AsynFixedFL algorithm can effectively solve the problem of device heterogeneity and energy consumption limitation of edge nodes.

Integrated system of traditional THz time-domain spectroscopy and asynchronous optical sampling

Terahertz time-domain spectroscopy(THz-TDS)system,as a new means of spectral analysis and detection,plays an increasingly pivotal role in basic scientific research.However,owing to the long scanning time of the traditional THz-TDS system and the complex control of the asynchronous optical scanning(ASOPS)system,which requires frequent calibration,we combine traditional THz-TDS and ASOPS systems to form a composite system and propose an all-fiber trigger signal generation method based on the time overlapping interference signal generated by the collinear motion of two laser pulses.Finally,the time-domain and frequency-domain spectra are obtained by using two independent systems in the integrated systems.It is found that the full width at half maximum(FWHM)of the time-domain spectra and the spectral width of the frequency-domain spectra are almost the same,but the sampling speed of the ASOPS system is significantly faster than that of the traditional THz-TDS system,which conduces to the study of the transient characteristics of substances.

Research on the Mechanism of Multi-Sensor Fusion Configuration Based on the Optimal Principle of the Vehicle

In order to address the issue of sensor configuration redundancy in intelligent driving,this paper constructs a multi-objective optimization model that considers cost,coverage ability,and perception performance.And then,combining a specific set of parameters,the NSGA-II algorithm is used to solve the multi-objective model established in this paper,and a Pareto front containing 24 typical configuration schemes is extracted after considering empirical constraints.Finally,using the decision preference method proposed in this paper that combines subjective and objective factors,decision scores are calculated and ranked for various configuration schemes from both cost and performance preferences.The research results indicate that the multi-objective optimization model established in this paper can screen and optimize various configuration schemes from the optimal principle of the vehicle,and the optimized configuration schemes can be quantitatively ranked to obtain the decision results for the vehicle under different preference tendencies.

State Estimation Method for GNSS/INS/Visual Multi-sensor Fusion Based on Factor Graph Optimization for Unmanned System

With the development of unmanned driving technology,intelligent robots and drones,high-precision localization,navigation and state estimation technologies have also made great progress.Traditional global navigation satellite system/inertial navigation system(GNSS/INS)integrated navigation systems can provide high-precision navigation information continuously.However,when this system is applied to indoor or GNSS-denied environments,such as outdoor substations with strong electromagnetic interference and complex dense spaces,it is often unable to obtain high-precision GNSS positioning data.The positioning and orientation errors will diverge and accumulate rapidly,which cannot meet the high-precision localization requirements in large-scale and long-distance navigation scenarios.This paper proposes a method of high-precision state estimation with fusion of GNSS/INS/Vision using a nonlinear optimizer factor graph optimization as the basis for multi-source optimization.Through the collected experimental data and simulation results,this system shows good performance in the indoor environment and the environment with partial GNSS signal loss.

Disparity estimation for multi-scale multi-sensor fusion

The perception module of advanced driver assistance systems plays a vital role.Perception schemes often use a single sensor for data processing and environmental perception or adopt the information processing results of various sensors for the fusion of the detection layer.This paper proposes a multi-scale and multi-sensor data fusion strategy in the front end of perception and accomplishes a multi-sensor function disparity map generation scheme.A binocular stereo vision sensor composed of two cameras and a light deterction and ranging(LiDAR)sensor is used to jointly perceive the environment,and a multi-scale fusion scheme is employed to improve the accuracy of the disparity map.This solution not only has the advantages of dense perception of binocular stereo vision sensors but also considers the perception accuracy of LiDAR sensors.Experiments demonstrate that the multi-scale multi-sensor scheme proposed in this paper significantly improves disparity map estimation.

Research on Transmission Line Tower Tilting and Foundation State Monitoring Technology Based onMulti-Sensor Cooperative Detection and Correction

The transmission line tower will be affected by bad weather and artificial subsidence caused by the foundation and other factors in the power transmission.The tower’s tilt and severe deformation will cause the building to collapse.Many small changes caused the tower’s collapse,but the early staff often could not intuitively notice the changes in the tower’s state.In the current tower online monitoring system,terminal equipment often needs to replace batteries frequently due to premature exhaustion of power.According to the need for real-time measurement of power line tower,this research designed a real-time monitoring device monitoring the transmission tower attitude tilting and foundation state based on the inertial sensor,the acceleration of 3 axis inertial sensor and angular velocity raw data to pole average filtering pre-processing,and then through the complementary filtering algorithm for comprehensive calculation of tilt angle,the system meets the demand for inclined online monitoring of power line poles and towers regarding measurement accuracy,with low cost and power consumption.The optimization multi-sensor cooperative detection and correction measured tilt angle result relative accuracy can reach 1.03%,which has specific promotion and application value since the system has the advantages of unattended and efficient calculation.

An Asynchronous Implementation of Add-Compare-Select Processor for Communication Systems

A novel asynchronous ACS(add-compare-select) processor for Viterbi decoder is described.It is controlled by local handshake signals instead of the globe clock.The circuits of asynchronous adder unit,asynchronous comparator unit,and asynchronous selector unit are proposed.A full-custom design of asynchronous 4-bit ACS processor is fabricated in CSMC-HJ 0.6μm CMOS 2P2M mixed-mode process.At a supply voltage of 5V,when it operates at 20MHz,the power consumption is 75.5mW.The processor has no dynamic power consumption when it awaits an opportunity in sleep mode.The results of performance test of asynchronous 4-bit ACS processor show that the average case response time 19.18ns is only 82% of the worst-case response time 23.37ns.Compared with the synchronous 4-bit ACS processor in power consumption and performance by simulation,it reveals that the asynchronous ACS processor has some advantages than the synchronous one.

Stability of Iterative Learning Control with Data Dropouts via Asynchronous Dynamical System

In this paper, the stability of iterative learning control with data dropouts is discussed. By the super vector formulation, an iterative learning control （ILC） system with data dropouts can be modeled as an asynchronous dynamical system with rate constraints on events in the iteration domain. The stability condition is provided in the form of linear matrix inequalities （LMIS） depending on the stability of asynchronous dynamical systems. The analysis is supported by simulations.

Dynamic Coupled Analysis of the Floating Platform Using the Asynchronous Coupling Algorithm

This paper discusses the numerical modeling of the dynamic coupled analysis of the floating platform and mooring/risers using the asynchronous coupling algorithm with the purpose to improve the computational efficiency when multiple lines are connected to the platform. The numerical model of the platform motion simulation in wave is presented. Additionally, how the asynchronous coupling algorithm is implemented during the dynamic coupling analysis is introduced. Through a comparison of the numerical results of our developed model with commercial software for a SPAR platform, the developed numerical model is checked and validated.

Application of the asynchronous advantage actor–critic machine learning algorithm to real-time accelerator tuning

This paper describes a real-time beam tuning method with an improved asynchronous advantage actor–critic(A3C)algorithm for accelerator systems.The operating parameters of devices are usually inconsistent with the predictions of physical designs because of errors in mechanical matching and installation.Therefore,parameter optimization methods such as pointwise scanning,evolutionary algorithms(EAs),and robust conjugate direction search are widely used in beam tuning to compensate for this inconsistency.However,it is difficult for them to deal with a large number of discrete local optima.The A3C algorithm,which has been applied in the automated control field,provides an approach for improving multi-dimensional optimization.The A3C algorithm is introduced and improved for the real-time beam tuning code for accelerators.Experiments in which optimization is achieved by using pointwise scanning,the genetic algorithm(one kind of EAs),and the A3C-algorithm are conducted and compared to optimize the currents of four steering magnets and two solenoids in the low-energy beam transport section(LEBT)of the Xi’an Proton Application Facility.Optimal currents are determined when the highest transmission of a radio frequency quadrupole(RFQ)accelerator downstream of the LEBT is achieved.The optimal work points of the tuned accelerator were obtained with currents of 0 A,0 A,0 A,and 0.1 A,for the four steering magnets,and 107 A and 96 A for the two solenoids.Furthermore,the highest transmission of the RFQ was 91.2%.Meanwhile,the lower time required for the optimization with the A3C algorithm was successfully verified.Optimization with the A3C algorithm consumed 42%and 78%less time than pointwise scanning with random initialization and pre-trained initialization of weights,respectively.

ASYNCHRONOUS RELAXED ITERATIVE METHODS FOR SOLVING LINEAR SYSTEMS OF EQUATIONS

In this paper, the asynchronous versions of classical iterative methods for solving linear systems of equations are considered. Sufficient conditions for convergence of asynchronous relaxed processes are given for H-matrix by which nor only the requirements of [3] on coefficient matrix are lowered, but also a larger region of convergence than that in [3] is obtained.

Privacy Preserving Solution for the Asynchronous Localization of Underwater Sensor Networks

Location estimation of underwater sensor networks(USNs)has become a critical technology,due to its fundamental role in the sensing,communication and control of ocean volume.However,the asynchronous clock,security attack and mobility characteristics of underwater environment make localization much more challenging as compared with terrestrial sensor networks.This paper is concerned with a privacy-preserving asynchronous localization issue for USNs.Particularly,a hybrid network architecture that includes surface buoys,anchor nodes,active sensor nodes and ordinary sensor nodes is constructed.Then,an asynchronous localization protocol is provided,through which two privacy-preserving localization algorithms are designed to estimate the locations of active and ordinary sensor nodes.It is worth mentioning that,the proposed localization algorithms reveal disguised positions to the network,while they do not adopt any homomorphic encryption technique.More importantly,they can eliminate the effect of asynchronous clock,i.e.,clock skew and offset.The performance analyses for the privacy-preserving asynchronous localization algorithms are also presented.Finally,simulation and experiment results reveal that the proposed localization approach can avoid the leakage of position information,while the location accuracy can be significantly enhanced as compared with the other works.