Local topography-induced pressure gradient effects on the wake and power output of a model wind turbine

Wind-tunnel experiments were performed to study the effect of favorable and adverse constant pressure gradients(PG)from local changes in the topography right downwind of a model wind turbine.Particle image velocimetry was used to characterize the near and intermediate wake regions.We explored five scenarios,two favorable,two adverse PG,and a case with negligible PG.Results show that the PGs induce a wake deflection and modulate the wake.They imposed a relatively small impact on the turbulence kinetic energy and kinematic shear stress but a comparatively dominant effect on the bulk flow on the flow recovery.Based on this,a simple formulation is used to describe the impact of PG on the wake.We modeled the base flow through a linearized perturbation method;the wake is obtained by solving a simplified,integrated streamwise momentum equation.This approach reasonably estimated the flow profile and PG-induced power output variations.

Back Pressure Characteristics for Turbine Channel of External-Parallel TBCC Inlet

For investigating the back pressure characteristics of turbine channel of an external-parallel turbine-based combined cycle(TBCC)inlet during the mode transition with the freestream air Mach number of 1.8,wind tunnel tests and numerical simulations are carried out.The results show that the critical back pressure of the turbine channel decreases linearly with the decrease of the open degree of splitter plate.The turbine channel has self-starting capacity when the open degree of the turbine channel is 100%.The total pressure recovery coefficient increases with the increase of back pressure when turbine channel is at supercritical and critical state.The mass capture ratio,total pressure recovery coefficient and outlet pressure ratio decrease obviously when turbine channel is at subcritical state.Results of the research would provide scheme reference and technology storage for TBCC propulsion evolution.

Experimental Study of the Pressure Fluctuations in a Pump Turbine at Large Partial Flow Conditions

Frequent shifts of output and operating mode require a pump turbine with excellent stability. Current researches show that large partial flow conditions in pump mode experience positive-slope phenomena with a large head drop. The pressure fluctuation at the positive slope is crucial to the pump turbine unit safety. The operating instabilities at large partial flow conditions for a pump turbine are analyzed. The hydraulic performance of a model pump turbine is tested with the pressure fluctuations measured at unstable operating points near a positive slope in the performance curve. The hydraulic performance tests show that there are two separated positive-slope regions for the pump turbine, with the flow discharge for the first positive slope from 0.85 to 0.91 times that at the maximum efficiency point. The amplitudes of the pressure fluctuations at these unstable large partial flow conditions near the first positive slope are much larger than those at stable operating condtions. A dominant frequency is measured at 0.2 times the impeller rotational frequency in the flow passage near the impeller exit, which is believed to be induced by the rotating stall in the flow passage of the wicket gates. The test results also show hysteresis with pressure fluctuations when the pump turbine is operated near the first positive slope. The hysteresis creates different pressure fluctuations for those operation points even though their flow rates and heads are similar respectively. The pressure fluctuation characteristics at large partial flow conditions obtained by the present study will be helpful for the safe operation of pumped storage units.

Numerical Simulation of Pressure Fluctuations in a Large Francis Turbine Runner

The pressure fluctuation caused by unsteady flow in runner is one of the main reasons of vibration for a large Francis hydraulic turbine. It directly affects the steady operation of the hydraulic turbine unit. The existing research of the pressure fluctuation in hydraulic turbine mainly focuses on the unsteady flow in draft tube. Accurate distribution of pressure fluctuations inside a runner is not very clear. In this paper, the numerical method for predicting the pressure fluctuations in runner is investigated and the numerical simulation is performed for a large Francis hydraulic turbine. It is proved that the combination of shear-stress transport（SST） k-o） turbulence model and pressure-implicit with splitting of operators（PISO） algorithm could give more reliable prediction of pressure fluctuations in runner. The frequencies of pressure fluctuations in runner are affected by the flow in guide vane and the flow in draft tube The first dominant frequency is significantly determined by the flow in draft tube, especially at part load condition. This frequency is approximately equal to one-third of the runner rotating frequency. The evident second dominant frequency is exactly equal to the guide vane passing frequency. The peak-to-peak amplitudes of pressure fluctuations in runner at small guide vane open angle are larger than that at large open angle at the same operating head. The amplitudes at points on blade pressure surface are generally greater than that on suction surface. The research results could be used to direct the hydraulic design and operation stability improvement of a large Francis hydraulic turbine.

AN INVISCID MODEL FOR THE BASE PRESSURE OF TRANSONIC TURBINE CASCADE

An inviscid base pressure model for transonic turbine blade has been presented. It has been shown that for a given back pressure the base pressure at the trailing edge, and the profile loss of a turbine blade are fixed according to the model and the base pressure can be calculated with the help of an inviscid numerical scheme. A parameteric study on the model shows that a blade profile with positive curvature downstream of the throat is advantageous for generating less loss, whilst the worst situation is when the exit flow reaches the sonic condition.

Effects of stator bending on pressure field and loss of transonic turbine stage

To study effects of the upstream flow field changing on the downstream flow field of transonic turbine, different three-dimensional bowed blades, which are the stator blades of transonic turbine stage, were designed in this paper. And then numerical calculations were carried out. The effects on downstream flow field were studied and analyzed in detail. Results show that, at the middle of stator blades, although the increasing Mach number causes the increase of shock-wave strength and friction, the middle flow field of downstream rotors is improved obviously. It is an important change in transonic condition. This causes the loss of the rotor’s middle part decreased greatly. Correspondingly, efficiency of the whole transonic stage can be increased.

Calculation of the Choked Back Pressure for Steam Turbines with Air Cooled Condensers

The choked back pressure characteristic of the steam turbine unit with air cooled condenser is very different with the unit with wet cooling technology, and the understanding of the choked back pressure performance change with operation load is important to guide the economic operation of the unit. One simplified Variable Operation Condition Analysis Method was put forward for calculation of the unit output-turbine back pressure characteristics. Based on this method, the choked back pressure for each operation load can be determined. An example was given for a super-critical, regenerative single-shaft, 2-casing with 2-exhaust steam turbine generation unit with air cooled condenser. The calculation result was provided and compared with the result of the unit with wet cooling technology.

Analogy Theory and Application of Pressure Difference of Wind Turbine Blade Profile

This paper aims to design an optimized blade for Horizontal Axis Wind Turbine(HWAT).Since airfoil is a basic component of blade design,an optimized airfoil(referred as SJX)was proposed based on the line theory through the weight analogy to pressure distribution of air flow.Its lift,drag,lift⁃to⁃drag ratio were compared with those NACA2409⁃34,NACA2410,and RK40 airfoils by using Profili software at fixed wind velocity and under different angles of attack.The NACA2409⁃34 airfoil was found to be greatly similar with the SJX airfoil.Based on the Wilson method,blades using SJX and NACA2490⁃34 airfoils were developed and different performance parameters such as velocity distribution,pressure distribution,and power were compared under variable wind velocities and different angles of attack ranging from-4°to 6°at different radius from the center of rotor using computational fluid dynamics(CFD)in ANSYS FLUENT.Results of the study suggested that the performance of the SJX based airfoil and blade was much more optimized.

基于E-Wind Turbine实验平台的风力发电控制系统

风力发电系统具有规模大、实际现场培训成本高、危险系数高等特点,因此基于风力发电仿真设备的风力发电控制研究是十分必要的。以E-Wind Turbine实验平台为例,详细介绍了变速、变桨距双馈风力发电系统实验平台的构成与控制策略的实现方法。基于S7-1200系列的PLC控制器,利用PORTAL STEP 7集成开发环境,实现了风机的偏航、转速控制以及功率控制。仿真实验结果表明,设计的风力发电控制系统可以有效地模拟实际风力发电机的各种控制要求,为风力发电控制策略的研究提供了一种有效手段。

Transient simulation of a pump-turbine with misaligned guide vanes during turbine model start-up

Experimental studies of a model pump-turbine S-curve characteristics and its improvement by misaligned guide vanes （MGV） were extended to prototype pump turbine through 3-D transient flow simulations. The unsteady Reynolds-averaged Navier-Stokes equations with the SST turbulence model were used to model the transient flow within the entire flow passage of a reversible pump-turbine with and without misaligned guide vanes during turbine model start-up. The unstable S-curve and its improvement by using misaligned guide vane were verified by model test and simulation. The transient flow calculations were used to clarify the variations of pressure pulse and internal flow behavior in the entire flow passage. The use of misaligned guide vanes can eliminate the S-curve characteristics of a pump-turbine, and can significantly increase the pressure pulse amplitude in the entire flow passage and the runner radial forces during start-up. The MGV only decreased the pulse amplitude on the guide vane suction side when the rotating speed was less than 50% rated speed. The hydraulic reason is that the MGV dramatically changed the flow patterns inside the entire flow passage, and destroyed the symmetry of the flow distribution inside the guide vane and runner.

Dynamic Analysis of A 5-MW Tripod Offshore Wind Turbine by Considering Fluid–Structure Interaction

Fixed offshore wind turbines usually have large underwater supporting structures. The fluid influences the dynamic characteristics of the structure system. The dynamic model of a 5-MW tripod offshore wind turbine considering the pile-soil system and fluid structure interaction （FSI） is established, and the structural modes in air and in water are obtained by use of ANSYS. By comparing low-order natural frequencies and mode shapes, the influence of sea water on the free vibration characteristics of offshore wind turbine is analyzed. On basis of the above work, seismic responses under excitation by E1-Centro waves are calculated by the time-history analysis method. The results reveal that the dynamic responses such as the lateral displacement of the foundation and the section bending moment of the tubular piles increase substantially under the influence of the added-mass and hydrodynamic pressure of sea water. The method and conclusions presented in this paper can provide a theoretical reference for structure design and analysis of offshore wind turbines fixed in deep seawater.

Pore-scale study of the pressure-sensitive effect of sandstone and its influence on multiphase flows

The pressure-sensitive effect on the pore structure of sandstone was investigated using X-ray computed micro-tomography and QEMSCAN quantitative mineral analysis. In a physical simulation study, we extracted the pore network model from digital cores at different confining pressures and evaluated the effect of pressure sensitivity on the multiphase displacement process. In both the pore network model and QEMSCAN scanning, the pore structure was observed to be damaged under a high confining pressure. Due to their different scales, the pores and throats exhibited inhomogeneous changes; further, the throats exhibited a significant variation compared to that exhibited by the pores. Meanwhile, the heterogeneity of the pore structure under the two aforementioned activities was aggravated by the elastic-plastic deformation of the pore structure.The pressure-sensitive effect increased the proportion of mineral particles, such as quartz(the main component of the core skeleton), and reduced the proportion of clay minerals. The clay minerals were originally attached to the pore walls or interspersed in the pores; however, as the pressure increased, the clay minerals accumulated in the pores resulting in blockage of the pores. While simulating the multiphase displacement process, increasing the confining pressure was observed to severely restrict the flowability of oil and water. This study promises to improve the efficiency of reservoir development in terms of oil and gas exploitation.

Development and Installation of High Pressure Boilers for Co-Generation Plant in Sugar Industries

The sugar cane containing minimum 30% fiber was referred as bagasse and used the generation of power required for the operation of sugar mill. The bagasse is fired in the boiler for producing steam at high pressure, which is extracted through various single high capacity turbines and used in the process. The installation of high pressure boilers and high pressure turbo-generators has provision for the operation of co-generation plant during the off-season also that enhances the power generation from 9MW to 23MW. The annual monetary benefits achieved are Rs. 204.13 million and this was based on cost of power sold to the grid @ Rs 2.548 per unit, sugar season of 219 days and off season of 52 days. This required an investment of Rs 820.6 million. The investment had an attractive simple payback period of 48 months.

Feasibility Analysis of Back-Pressure Steam Feeding Water Pump for Direct Air-Cooled Unit

As the performance of an air-cooled condenser is apt to be affected by the fluctuating ambient condition, some difficulties are brought to the use of a steam feeding water pump in an air-cooled unit. This paper introduces a new design of for steam feeding the water pump of an air-cooled unit using the back-pressure steam turbine as the prime motor. Using variable condition analysis on a 600 MW direct air-cooled unit, and with consideration of the effect on the ambient conditions, the feasibility, economy, and adaptability of the design are verified.

Comparison of electrochemical properties of atmospheric pressure plasma coatings for Al_2O_3-3TiO_2 and CoNiCrAlY in sea water

To improve the durability of underwater rotating products,the corrosion characteristics in harsh marine environment were evaluated through various electrochemical experiments on the Al2O3-3TiO2 and CoNiCrAlY coating layers by atmospheric pressure plasma spray coating process.By evaluating the corrosion resistance of these materials,their applicability to environmentally friendly power generation equipment such as blades of tidal current turbines was examined.According to the Tafel analysis for micro-areas including the coating layer,the coating/metal interlayer and the base metal,the Al2O3-3TiO2 coating layer and the CoNiCrAlY coating layer show markedly lower corrosion current density than the base metal.The corrosion current density of the CoNiCrAlY coating layer (9.75316×10-8A/cm2) is about 1.6 times more than that of the Al2O3-3TiO2 coating layer (6.13139×10-8A/cm2).

C12-3.43/0.981 Type 12MW Exhaustion and Condensing Stean Turbine

TheQingdaoJienengPowerGroupCompanyinShandongmanufactUreseightseriesofsteamtIJrbinesin140varieties,witheachturbinebelow25MaTheC12-3.43/0.98type12MWexhaustionandcondensingsteamturbinehasthefollowingfeatures:12mW:ipa,435C,0.981Mpa,andh/h,whichcanbeusedi...

Correlation analysis of cavitation-induced pressure pulsation and vibration in a bulb turbine

Cavitation is one of the main causes of deteriorating stability of bulb turbines.To enhance their stability,this study examines the effects of runner cavitation on draft tube pressure fluctuation and vibration in bulb turbine through experimental methods.With varying cavitation coefficients,a synchronous test system,including a high-speed camera,vibration acceleration sensors and pressure pulsation sensors,is applied to obtain cavitation images of the runner,vibration and internal fluid pressure pulsation data of the draft tube.The results show that the correlated component of pressure pulsation signals during the cavitation process is the synchronous pressure pulsation of 16f_(n)With the development of cavitation,the amplitude of synchronous pressure pulsation increases first and then decreases.Cavitation enhances the high-frequency vibration on the wall of runner chamber.The root mean square(rms)of the vertical vibration component IMF3,the horizontal vibration components IMF2,IMF4 are linearly negatively correlated with the cavitation coefficient.The associated component between cavitation-induced vibration and pressure pulsation signal is 16f_(n)and its harmonics.In the process of cavitation,pressure pulsation plays a leading role in vibration.

The Third-Order Viscoelastic Acoustic Model Enables an Ice-Detection System for a Smart Deicing of Wind-Turbine Blade Shells

The present work is based on the third-order partial differential equation (PDE) of acoustics of viscoelastic solids for the quasi-equilibrium (QE) component of the average normal stress. This PDE includes the stress-relaxation time (SRT) for the material and is applicable at any value of the SRT. The notion of a smart deicing system (SDS) for blade shells (BSs) of a wind turbine is specified. The work considers the stress in a BS as the one caused by the operational load on the BS. The work develops key design issues of a prospective ice-detection system (IDS) able to supply an array of the heating elements of an SDS with the element-individual spatiotemporal data and procedures for identification of the material parameters of atmospheric-ice (AI) layer accreted on the outer surfaces of the BSs. Both the SDS and IDS flexibly allow for complex, curvilinear and space-time-varying shapes of BSs. The proposed IDS presumes monitoring of the QE components of the normal stresses in BSs. The IDS is supposed to include an array of pressure-sensing resistors, also known as force-sensing resistors (FSRs), and communication hardware, as well as the parameter-identification software package (PISP), which provides the identification on the basis of the aforementioned PDE and the data measured by the FSRs. The IDS does not have hardware components located outside the outer surfaces of, or implanted in, BSs. The FSR array and communication hardware are reliable, and both cost- and energy-efficient. The present work extends methods of structural-health/operational-load monitoring (SH/OL-M) with measurements of the operational-load-caused stress in closed solid shells and, if the prospective PISP is used, endows the methods with identification of material parameters of the shells. The identification algorithms that can underlie the PISP are computationally efficient and suitable for implementation in the real-time mode. The identification model and algorithms can deal with not only the single-layer systems such as the BS layer without the AI layer or two-layer systems but also multi-layer systems. The outcomes can be applied to not only BSs of wind turbines but also non-QE closed single- or multi-layer deformable solid shells of various engineering systems (e.g., the shells of driver or passenger compartments of ships, cars, busses, airplanes, and other vehicles). The proposed monitoring of the normal-stress QE component in the mentioned shells extends the methods of SH/OL-M. The topic for the nearest research is a better adjustment of the settings for the FSR-based measurement of the mentioned components and a calibration of the parameter-identification model and algorithms, as well as the resulting improvement of the PISP.