In this paper,such a new lateral displacement function is proposed that the lateral flow velocity is con- tinuous at the entry and the exit of deformation zone.A new kind of finite strip method—the third power B-spli...In this paper,such a new lateral displacement function is proposed that the lateral flow velocity is con- tinuous at the entry and the exit of deformation zone.A new kind of finite strip method—the third power B-spline finite strip method—is put forward to simulate strip rolling process.Front and back tension stresses are formulated.The computed results of the transverse distributions of the front and back tension stresses are close to the experimental results.The paper lays a foundation for further analysing the three-dimensional stresses and deformations of strip rolling.展开更多
X-ray diffraction and orientation mapping in EBSD measurement were applied to obtain information of deformation and recrystallization with the emphasis on the cube orientation in hot rolled high purity aluminum plates...X-ray diffraction and orientation mapping in EBSD measurement were applied to obtain information of deformation and recrystallization with the emphasis on the cube orientation in hot rolled high purity aluminum plates. It is shown that cube orientations are retained to a large extent during hot rolling. Some deformed cube grains are found to have experienced large extent of recovery according to their Kikuchi band contrasts. The deformed cube-oriented grains in hot rolled plates are in an unfavorite growth condition with respect to their neighboring grain orientations for the subsequent annealing. The reasons for the phenomena observed, as well as the influence of hot rolling process on subsequent cold rolling and final annealing were discussed.展开更多
The condition monitoring and fault diagnosis of rolling element bearings are particularly crucial in rotating mechanical applications in industry. A bearing fault signal contains information not only about fault condi...The condition monitoring and fault diagnosis of rolling element bearings are particularly crucial in rotating mechanical applications in industry. A bearing fault signal contains information not only about fault condition and fault type but also the severity of the fault. This means fault severity quantitative analysis is one of most active and valid ways to realize proper maintenance decision. Aiming at the deficiency of the research in bearing single point pitting fault quantitative diagnosis, a new back-propagation neural network method based on wavelet packet decomposition coefficient entropy is proposed. The three levels of wavelet packet coefficient entropy（WPCE） is introduced as a characteristic input vector to the BPNN. Compared with the wavelet packet decomposition energy ratio input vector, WPCE shows more sensitive in distinguishing from the different fault severity degree of the measured signal. The engineering application results show that the quantitative trend fault diagnosis is realized in the different fault degree of the single point bearing pitting fault. The breakthrough attempt from quantitative to qualitative on the pattern recognition of rolling element bearings fault diagnosis is realized.展开更多
By optical inspection of macro-etched metallography and electron back-scattered diffraction （EBSD） mapping, this paper analyzed the microstructure of austenitic stainless steel strips produced with an equal-diameter...By optical inspection of macro-etched metallography and electron back-scattered diffraction （EBSD） mapping, this paper analyzed the microstructure of austenitic stainless steel strips produced with an equal-diameter twin-roll strip caster. The results indicate that the microstructure of the strips includes two columnar zones with highly compact dendrites and one equiaxed zone. The characteristics, such as grain size and growing direction of columnar grains and equiaxed grains, were investigated. An additional transitional area with many finer grains between the columnar zone and the equiaxed zone was found. As shown in EBSD analysis, small angle boundaries exist both in the columnar zone and the equiaxed zone, although they are especially more in the transitional area. Additionally, some 〈111〉 twin boundaries were found in the microstructure of the strips.展开更多
文摘In this paper,such a new lateral displacement function is proposed that the lateral flow velocity is con- tinuous at the entry and the exit of deformation zone.A new kind of finite strip method—the third power B-spline finite strip method—is put forward to simulate strip rolling process.Front and back tension stresses are formulated.The computed results of the transverse distributions of the front and back tension stresses are close to the experimental results.The paper lays a foundation for further analysing the three-dimensional stresses and deformations of strip rolling.
文摘X-ray diffraction and orientation mapping in EBSD measurement were applied to obtain information of deformation and recrystallization with the emphasis on the cube orientation in hot rolled high purity aluminum plates. It is shown that cube orientations are retained to a large extent during hot rolling. Some deformed cube grains are found to have experienced large extent of recovery according to their Kikuchi band contrasts. The deformed cube-oriented grains in hot rolled plates are in an unfavorite growth condition with respect to their neighboring grain orientations for the subsequent annealing. The reasons for the phenomena observed, as well as the influence of hot rolling process on subsequent cold rolling and final annealing were discussed.
基金Supported by National Natural Science Foundation of China(Grant Nos.51175007,51075023)
文摘The condition monitoring and fault diagnosis of rolling element bearings are particularly crucial in rotating mechanical applications in industry. A bearing fault signal contains information not only about fault condition and fault type but also the severity of the fault. This means fault severity quantitative analysis is one of most active and valid ways to realize proper maintenance decision. Aiming at the deficiency of the research in bearing single point pitting fault quantitative diagnosis, a new back-propagation neural network method based on wavelet packet decomposition coefficient entropy is proposed. The three levels of wavelet packet coefficient entropy（WPCE） is introduced as a characteristic input vector to the BPNN. Compared with the wavelet packet decomposition energy ratio input vector, WPCE shows more sensitive in distinguishing from the different fault severity degree of the measured signal. The engineering application results show that the quantitative trend fault diagnosis is realized in the different fault degree of the single point bearing pitting fault. The breakthrough attempt from quantitative to qualitative on the pattern recognition of rolling element bearings fault diagnosis is realized.
基金supported by the National Natural Science Foundation of China (No. 50434040)
文摘By optical inspection of macro-etched metallography and electron back-scattered diffraction （EBSD） mapping, this paper analyzed the microstructure of austenitic stainless steel strips produced with an equal-diameter twin-roll strip caster. The results indicate that the microstructure of the strips includes two columnar zones with highly compact dendrites and one equiaxed zone. The characteristics, such as grain size and growing direction of columnar grains and equiaxed grains, were investigated. An additional transitional area with many finer grains between the columnar zone and the equiaxed zone was found. As shown in EBSD analysis, small angle boundaries exist both in the columnar zone and the equiaxed zone, although they are especially more in the transitional area. Additionally, some 〈111〉 twin boundaries were found in the microstructure of the strips.
