Influences of electric-hydraulic chattering on backward extrusion process of 6061 aluminum alloy

The possibility of the electric-hydraulic chattering technology and its application in the cold extrusion were presented.The conventional and electric-hydraulic chattering assisted backward extrusion processes were performed on 6061 aluminum alloy billets at room temperature.The experimental results showed that 5.65% reduction in the extrusion load was attained if the die and ejector were vibrated at a frequency of 100 Hz and amplitude of 0.013 mm in the longitudinal direction.The friction coefficient at the billet and tool system interface determined from the finite element analysis（FEA） decreased from 0.2 without chattering to 0.1 with application of electric-hydraulic chattering.The higher values of instantaneous velocity and direction change of material flow were achieved during the chattering assisted backward extrusion process.The strain distribution of the chattering assisted backward extrusion billet revealed lower maximum strain and smoother strain distribution in comparison with that produced by the conventional extrusion method.

Effect of circumferential strain rate on dynamic recrystallization and texture of Mg-13Gd-4Y-2Zn-0.5Zr alloy during rotary backward extrusion

Gleeble-3500 thermal simulator was applied to realize the rotary backward extrusion forming of Mg-13Gd-4Y-2Zn-0.5Zr(wt%)alloy at different circumferential strain rate from 0.009 s^(-1)to 0.027 s^(-1)at 400℃and the dynamic recrystallization mechanism and texture evolution were studied.The results show that the grain size of the alloy was obviously refined after rotary backward extrusion.As the circumferenlial strain rate increased,the dynamic recrystallization fraction gradually increased causing the grain size decreased and the distribution of microstructure became more uniform.At the same time,the texture of{0001},{10-10},{11-20}was weakened and the grain orientation distribution became more random.With the increase of circumferential strain rate,the discontinuous dynamic recrystallization mechanism became dominant,which promoted the weakening of texture and grain refinement of the alloy.

The evolution of microstructure and texture of AZ80 Mg alloy cup-shaped pieces processed by rotating backward extrusion

This study proposed an effective plastic deformation technique,rotating backward extrusion(RBE),for producing high performance AZ80 magnesium alloy cup-shaped pieces.The RBE process was carried on the Gleeble-3500 test machine at 653 K,and the conventional backward extrusion(CBE)was also conducted for comparison.A detailed microstructure analysis was performed using the optical microscopy(OM)and electron back-scatter diffraction(EBSD).The results shown that the equivalent strain and deformation uniformity of the cup pieces could be substantially increased by the RBE process compared with the CBE process.Furthermore,the RBE process could significantly improve the grain refining capacity and the proportion of dynamic recrystallization(DRX),of which the maximum reduction of grain size was 88.60%,and the maximum increase of DRX proportion was 55.30%in the cup bottom.The main deformation mechanism of the RBE process was the discontinuous DRX(DDRX),while the continuous DRX(CDRX)was also occurred in the cup transition.Compared with the CBE sample,the texture of the cup bottom was weakened for the RBE sample.The microhardness value of the RBE sample was higher than that of the CBE sample,which can be attributed to the grain refinement strengthening.

Determination of processing power and optimum billet radius of modified backward extrusion by upper bound approach

A recently developed backward extrusion method entitled “modified backward extrusion” was presented using an upper bound analysis. For this purpose deformation area was divided into four distinct zones and a kinematically admissible velocity field for each of them was suggested. Total dissipated power was calculated for the deformation zones and the extrusion power wascomputed. The correlations of important geometrical parameters with extrusion force and dissipated powers were shown. Finding the initial billet size, a challenging area in the modified backward extrusion method, was discussed and the optimum billet radius was obtained, considering the minimum relative extrusion pressure. Finite element analyses were conducted and the results werecompared with the upper bound analysis. Finally, experiments were executed on commercially pure aluminium and a good agreement between upper bound and finite element analyses with experimental values was observed.

Inhomogeneity of density and mechanical properties of A357 aluminum alloy backward extruded in semi-solid state

The inhomogeneity of density and mechanical properties of A357 aluminum alloy in the semi-solid state were investigated.Numerical simulation and backward extrusion were adopted to study the preparation of cup shells.The results show that the relative density of the wall is the lowest in samples,and that of the base is the highest.With increasing the billet height,more time is needed for relative density of the corner to reach the maximum value,and the relative densities in every region improve evidently with increasing the pressure.The tensile stress was simulated to be the largest at the corner,and the hot tearings were forecasted to mainly appear at the corner too.By employing proper billet height and pressure,the extruded samples consisted of fine and uniform microstructures,and can obtain excellent mechanical properties and Brinell hardness.

Hot deformation in nanocrystalline Nd-Fe-B backward extruded rings

Radially oriented Nd-Fe-B rings are prepared by backward extrusion of fine grained melt-spun powder. Melt- spun powder with the nominal composition of Nd30.5Febal.Co6.0Ga0.6A10.2B0.9 （wt%） is used as starting material. The effects of process variables, such as deformation temperature （Td）, strain rate （ε） and height reduction （△h%）, on the magnetic properties of the rings are investigated. A scanning electron microscope （SEM） equipped with an energy spectrum device is used to study the metallograph and microfracture of the extruded rings. The Br and （BH）max reach the optimum values at Td =800℃,ε= 0.01 mm/s, and △h% = 70%. It is found by SEM observations that the particle boundaries, which seemingly correspond to the interfaces of the starting melt-spun powders, emerge after the corrosion of metallography specimens. This is helpful for studying the effects of powder-powder interface on the local deformation and deformation homogeneity in the rings. For different spatial positions of the extruded rings, there are characteristic metallographies and microfractures. The upper end of the rings has the least deformation and worst texture, and therefore the worst magnetic properties. The magnetic properties in the radial direction increase slightly along the axis from the bottom to the middle, then steeply decrease at the upper end of the ring. The deformation and the formation-of-texturing processes are discussed. The deformation and the texturing formation of melt-spun Nd-Fe-B alloys probably involve grain boundary sliding and grain rotation, the solution-precipitation process and preferential growth of Nd2Fel4B nanograins along the easy growth a-axis.

Structural and magnetic properties of backward extruded Nd–Fe–B ring magnets made by different punch chamfer radius

Radially oriented Nd-Fe-B ring magnets were prepared by backward extrusion of MQ-C powder. The punch chamfer radius has a great impact on the microstructure and magnetic properties of the ring magnet. With the chamfer radius changing from 2, 5 to 8 mm, the cracks in the inner wall decrease obviously while the crystallographic alignment drops. Furthermore, the mechanism of caxis growth was suggested to be a combination of shear deformation in the corner and solution-precipitation under the stress parallel to radial direction. The alignment drops on the top of ring because the grains grow freely and some textured grains grow through nucleation and recrystallization. In the present work, the optimal punch chamfer radius is found to be 2 mm, and in this case, the remanence,coercivity, and maximum energy product of the ring magnet achieve 1.4 T, 670 kJám, and 342 kJám,respectively.

Enhancing strength and ductility in back extruded WE71 magnesium alloy cylindrical parts by introduction of multi-direction forging process

Magnesium cylindrical parts have relatively poor mechanical properties and distinct anisotropy of microstructure,which hinder their application as structural components.To improve the performance of WE71 cylindrical parts,multi-direction forging(MDF)was introduced before back extrusion,and the microstructure and mechanical properties were investigated.Results of microstructure show that the grain size in the outer of the cylindrical bottom is refined from 30.1 to 27.7μm,the micro structure is more uniform and the dislocation density is higher.The bimodal grain structure is formed in the outer of the cylindrical wall,which is ascribed to the formation of MgsRE phases along grain boundaries.These phases result in the Zener pinning effect on grain boundaries and the reduction of DRX volume fraction.The texture type of the cylindrical bottom is<0001>‖ED and the cylindrical wall is<1010>‖ED,and the maximum pole intensity is 1.986 and 1.664,respectively.Results of the tensile test at room temperature show that combined improved strength and ductility of the cylindrical part is attained after introducing the MDF process.The ultimate tensile strength(UTS),yield strength(YS)and elongation are279 MPa,185 MPa and 12%at the bottom and 299 MPa,212 MPa and 20%at the wall.

Microstructure,Mechanical Properties and Corrosion Behavior of Extruded Mg–Zn–Ag Alloys with Single-Phase Structure

Mg–Zn–Ag alloys have been extensively studied in recent years for potential biodegradable implants due to their unique mechanical properties,biodegradability and biocompatibility.In the present study,Mg–3Zn-x Ag（wt%,x=0.2,0.5 and0.8）alloys with single-phase crystal structure were prepared by backward extrusion at 340°C.The addition of Ag element into Mg–3Zn slightly influences the ultimate tensile strength and microstructure,but the elongation firstly increases from12%to 19.8%and then decreases from 19.8%to 9.9%with the increment of Ag concentration.The tensile yield strength,ultimate tensile strength and elongation of Mg–3Zn–0.2Ag alloy reach up to 142,234 MPa and 19.8%,respectively,which are the best mechanical performance of Mg–Zn–Ag alloys in the present work.The extruded Mg–3Zn–0.2Ag alloy also possesses the best corrosion behavior with the corresponding corrosion rate of 3.2 mm/year in immersion test,which could be explained by the single-phase and uniformly distributed grain structure,and the fewer twinning.