The sleeve sealing ball seat is one of the important components in the multistage fracturing process of horizontal wells.The erosion and wear of the surface will decrease the sealing performance of the fracturing ball...The sleeve sealing ball seat is one of the important components in the multistage fracturing process of horizontal wells.The erosion and wear of the surface will decrease the sealing performance of the fracturing ball and the ball seat.This leads to pressure leakage during the fracturing process and fracturing failure.In this paper,combined with the actual ball seat materials and working conditions during the fracturing process,the erosion tests of ductile iron and tungsten carbide materials under different erosion speeds,angles,and mortar concentrations are carried out.Then the erosion test results were analyzed by mathematical fitting,and a set of erosion models suitable for sliding sleeve setting ball seat materials were innovatively established.For the first time,this paper combines the erosion model obtained from the experiment and the computational fluid dynamics(CFD)with Fluent software to simulate the erosion of the ball seat.Based on the simulation results,the morphology of the sliding sleeve seat ball after erosion is predicted.Through analysis of the test and simulation results,it is showed that the erosion rate of tungsten carbide material is lower and the wear resistance is better under the condition of small angle erosion.This research can offer a strong basis for fracturing site selection,surface treatment methods,and prediction of failure time of ball seats.展开更多
To achieve the secondary production in multistage fracturing wells of tight oil,milling tools are usually used to remove the multistage fracturing ball seats to achieve production with a large diameter in later.In thi...To achieve the secondary production in multistage fracturing wells of tight oil,milling tools are usually used to remove the multistage fracturing ball seats to achieve production with a large diameter in later.In this paper,first of all,the working mechanism of milling tools for multistage fracturing ball seats was studied and a mechanical analysis model of single abrasive grain was established.Then,an experimental system for milling tools was developed,and the experimental tests of the flat,the blade,and the slope milling tool were conducted in order.Besides,the morphology of chips and the surface morphology of the workpiece after the experiment were analyzed.Also,the working performance of milling tools was evaluated from the perspectives of working safety,working efficiency,and wear resistance of the milling tool.The results show that the torque of the milling tool increases nonlinearly with the increase in the cutting depth of the abrasive grain and increases linearly with the increase in the cutting width.Also,the chips are irregular particles and the size is mainly from 10 to 50μm.So,the chips should be pumped up with a small pump pressure and a large displacement.Besides this,the cutting depths of the abrasive grains are from 216.20 to 635.47μm and the bottom surface of the milling tool should be eccentric to avoid the zero point of cutting speed.Furthermore,the torque of the slope milling tool is 23.8%larger than that of the flat milling tool,which is also 30.4%smaller than that of the blade milling tool.Compared with the flat milling tool,the working efficiency of the blade milling tool improves by 79.9%and the slope milling tool improves by 111.1%.Also,the wear resistance of the blade milling tool decreases by 102.7%,while the slope milling tool declines by 32.6%when compared with the flat milling tool.Therefore,the slope milling tool has the characteristics of moderate torque,stable working conditions,the highest working efficiency,and fine wear resistance,which is preferably used to mill multistage fracturing ball seats.This study provides a theoretical basis and guidance for milling multistage fracturing ball seats on-site and realizing production with a large diameter in later stages of multistage fracturing wells.展开更多
基金This research was funded by the National Natural Science Foundation of China(grant number 51675534).
文摘The sleeve sealing ball seat is one of the important components in the multistage fracturing process of horizontal wells.The erosion and wear of the surface will decrease the sealing performance of the fracturing ball and the ball seat.This leads to pressure leakage during the fracturing process and fracturing failure.In this paper,combined with the actual ball seat materials and working conditions during the fracturing process,the erosion tests of ductile iron and tungsten carbide materials under different erosion speeds,angles,and mortar concentrations are carried out.Then the erosion test results were analyzed by mathematical fitting,and a set of erosion models suitable for sliding sleeve setting ball seat materials were innovatively established.For the first time,this paper combines the erosion model obtained from the experiment and the computational fluid dynamics(CFD)with Fluent software to simulate the erosion of the ball seat.Based on the simulation results,the morphology of the sliding sleeve seat ball after erosion is predicted.Through analysis of the test and simulation results,it is showed that the erosion rate of tungsten carbide material is lower and the wear resistance is better under the condition of small angle erosion.This research can offer a strong basis for fracturing site selection,surface treatment methods,and prediction of failure time of ball seats.
基金supported by the National Science and Technology Major Project under Grant Nos.2016ZX05042004 and 2017ZX05072the Joint Funds of the National Natural Science Foundation of China under Grant No.U1762104+2 种基金the Postgraduate Innovation Project Foundation under Grant No.YCX2019054the Fundamental Research Funds for the Central Universities under Grant No.20CX02306Athe Opening Fund of National Engineering Laboratory of Offshore Geophysical and Exploration Equipment。
文摘To achieve the secondary production in multistage fracturing wells of tight oil,milling tools are usually used to remove the multistage fracturing ball seats to achieve production with a large diameter in later.In this paper,first of all,the working mechanism of milling tools for multistage fracturing ball seats was studied and a mechanical analysis model of single abrasive grain was established.Then,an experimental system for milling tools was developed,and the experimental tests of the flat,the blade,and the slope milling tool were conducted in order.Besides,the morphology of chips and the surface morphology of the workpiece after the experiment were analyzed.Also,the working performance of milling tools was evaluated from the perspectives of working safety,working efficiency,and wear resistance of the milling tool.The results show that the torque of the milling tool increases nonlinearly with the increase in the cutting depth of the abrasive grain and increases linearly with the increase in the cutting width.Also,the chips are irregular particles and the size is mainly from 10 to 50μm.So,the chips should be pumped up with a small pump pressure and a large displacement.Besides this,the cutting depths of the abrasive grains are from 216.20 to 635.47μm and the bottom surface of the milling tool should be eccentric to avoid the zero point of cutting speed.Furthermore,the torque of the slope milling tool is 23.8%larger than that of the flat milling tool,which is also 30.4%smaller than that of the blade milling tool.Compared with the flat milling tool,the working efficiency of the blade milling tool improves by 79.9%and the slope milling tool improves by 111.1%.Also,the wear resistance of the blade milling tool decreases by 102.7%,while the slope milling tool declines by 32.6%when compared with the flat milling tool.Therefore,the slope milling tool has the characteristics of moderate torque,stable working conditions,the highest working efficiency,and fine wear resistance,which is preferably used to mill multistage fracturing ball seats.This study provides a theoretical basis and guidance for milling multistage fracturing ball seats on-site and realizing production with a large diameter in later stages of multistage fracturing wells.
