Effectof Film Force Nonlinearity on Unbalance Responseof a Jeffcot RotorJournal Bearing System

The effect of oil film force nonlinearity on unbalance response of Jeffcot rotor elliptical bearing system is studied. Linear analysis is done by linearizing the bearing oil film dynamic forces and expressing them with stiffness and damping constants. Nonlinear dynamic simulation is done by taking the nonlinearity of bearing oil film dynamic force into full consideration, with the latter being expressed by a special database which is generated beforehand, and based on non stationary Reynolds equation and Reynolds boundary condition of film rupture. The linear and nonlinear unbalance responses of a Jeffcot rotor supported on a pair of elliptical bearings is studied. The resulting dynamic characteristics and rotor and journal whirling orbits are compared. While good consistancy between nonlinear and linear predictions is found under very small unbalance, significant or even drastic differences are found whenever the unbalance is not small, indicating the necessity of including the nonlinearity of oil film dynamic forces, especially when response to large unbalance is to be predicted.

Effects of bottom bracings on torsional dynamic characteristics of horizontally curved twin I-girder bridges with different curvatures

Curved twin I-girder bridges (CTIGBs) have low torsional stiffness that makes them vulnerable to dynamic loads. This study investigates the effects of bottom bracings on the torsional dynamic characteristics of CTIGBs. Five types of bottom bracings are designed to investigate their effects on the dynamic characteristics of CTIGBs with different curvatures under free and forced vibrations. To perform numerical investigations, three-dimensional (3-D) finite element (FE) bridge and vehicle models are established using commercial ANSYS code, and then a vehicle-bridge interaction analysis approach is proposed. Road roughness profiles generated from power spectral density and cross spectral functions are also taken into account in the analyses. The numerical results show that torsional frequencies increase significantly after providing bottom bracings, and the increasing rate depends on the type of bottom bracings and their locations of installation. Bottom bracings can act as load transmitting members from one main girder to the others. Large negative bearing forces that have occurred in bridges with small radii of curvatures can be remarkably reduced by providing bottom bracing systems. It is found that the performances of several bottom bracing systems are effective in improving the torsional dynamic characteristics of the bridges in this study.

CHARACTERISTCS OF FLUID FILM IN OPTIMIZED SPIRAL GROOVE MECHANICAL SEAL

In order to investigate the sealing performance variation resulted from the thermal deformation of the end faces, the equations to calculate the fluid film pressure distribution, the bearing force and the leakage rate are derived, for the fluid film both in parallel gap and in wedgy gap. The geometrical parameters of the sealing members are optimized by means of heat transfer analysis and complex method. The analysis results indicate that the shallow spiral grooves can generate hydrodynamic pressure while the rotating ring rotates and the bearing force of the fluid film in spiral groove end faces is much larger than that in the flat end faces. The deformation increases the bearing force of the fluid film in flat end faces, but it decreases the hydrodynamic pressure of the fluid film in spiral groove end faces. The gap dimensions which determine the characteristics of the fluid film is obtained by coupling analysis of the frictional heat and the thermal deformation in consideration of the equilibrium condition of the bearing force and the closing force. For different gap dimensions, the relation- ship between the closing force and the leakage rate is also investigated, based on which the leakage rate can be controlled by adjusting the closing force.

Effects of AMB Parameters on the Dynamic Stability of the Rotor

The motion equation of the rotor suspended by active magnetic bearing (AMB)is given in this paper after considering the nonlinear characteristics of the force.Fromthe response equation resulted from this Eq.we gained the functions of the jump ra-nge,and examined the effects of the A MB's parameters.

Impact of bending dies with different friction forms on forming force and quality of tubes manufactured by free bending technology

In the 3 D free bending forming system,the bending die can be designed either in a sliding type or rolling friction type.Bending die-based sliding friction type is often called normal bending dies;however,the bending dies-based rolling friction type includes bending die-based roller type and ball type in structure.In the current study,the impact of three bending dies on the forming force,and the bent tube quality was investigated.The obtained results showed that the tangential stresses and strains of the tubes formed by the bending die-based roller type were the smallest among the three bending dies.Besides,the spherical bearing force PUwas reduced drastically after using the roller type and ball type compared to the sliding friction type.Moreover,the uniformity of the wall thickness distribution of the tubes formed by the roller type and ball type was better than those obtained from the sliding friction type.In addition,the cross-section distortion rate was reduced by 2.8%using the roller type,and 1.8%using ball-type compared to the sliding friction type.