The simulated heat affected zone （HAZ） of the high strength low alloy （HSLA） steels containing 0%, 0.047%, 0.097% and 0.151% vanadium, respectively, were studied with Gleeble-2000 thermomechanical simulator to det...The simulated heat affected zone （HAZ） of the high strength low alloy （HSLA） steels containing 0%, 0.047%, 0.097% and 0.151% vanadium, respectively, were studied with Gleeble-2000 thermomechanical simulator to determine the influence of vanadium addition on the mechanical properties of the HAZ. The HAZ simulation involved reheating the samples to 1350℃, and then cooling to ambient temperature at a cooling rate of 5℃/s ranging from 800 to 500℃ （△8/5=60s）. The mechanical properties including tensile strength and -20℃ impact toughness were conducted. The microstructures of the base steel and the simulated HAZs were investigated using optical microscope, scanning electron microscope （ SEM ） and transmission electron microscope （TEM）. Based on the systemutic examination, the present work confirmed that about 0.05% vanadium addition to low carbon low alloy steels resulted in expected balance of strength and toughness of the HAZ. And more than 0.10% levels addition led to detrimental toughness of the HAZ SEM study showed that the simulated 0.097% and 0.151%V HAZs consisted of more coarse ferrite plates with greater and more M-A constituents along austenite grain and ferrite plate bound- aries. The impact fracture surfaces of the simulated 0.097% and 0.151%V HAZs showed typically brittle mode with predominant cleavages. The size of the facet in the fracture surface increased with increasing vanadium level from 0.097% to 0.151%.As a result, the simulated 0.151% V HAZ has the lowest impact toughness of the four specimens.展开更多
Microstructure evolution and impact toughness of simulated heat affected zone（HAZ） in low carbon steel have been investigated in this study. Thermal simulator was used to simulate microstructure evolution in HAZ wit...Microstructure evolution and impact toughness of simulated heat affected zone（HAZ） in low carbon steel have been investigated in this study. Thermal simulator was used to simulate microstructure evolution in HAZ with heat input of 10-100 kJ/cm welding thermal cycle. Results indicated that microstructure of HAZ mainly consisted of acicular ferrite（AF） inside grain and high volume fraction of grain boundaries ferrite（GBF） at prior austenite boundaries; the size of GBF and effective grain size increased with increasing heat input. Excellent impact toughness（more than 150 J at-40 ℃） was obtained in HAZ with heat input less than 50 k J/cm. When heat input was 100 kJ/cm, the impact toughness of HAZ decreased to 18 J because of the presence of large M-A constituent with lath-form in HAZ, assisting the micro-crack initiation and decreasing the crack initiation energy seriously. Effect of inclusions on acicular ferrite transformation in HAZ was also discussed.展开更多
The relationship between the t8/5 and micro-hardness, impact toughness in the heat affected zone （HAZ） of ASME SA213-792 at peak temperature of 1 350 ℃ was studied by thermal simulation. The result shows that the m...The relationship between the t8/5 and micro-hardness, impact toughness in the heat affected zone （HAZ） of ASME SA213-792 at peak temperature of 1 350 ℃ was studied by thermal simulation. The result shows that the micro-hardness of HAZ rises at the beginning and then decreases with increasing of t8/5 , whereas the impact toughness presents reverse trend. The distribution of precipitates in substrate has great influence on the impact toughness of HAZ. When the t8/5 is 40 s, chain-like precipitates lower the impact toughness of HAZ seriously.展开更多
The high strength bridge steel was processed with the simulated coarse grain heat affected zone（CGHAZ） thermal cycle with heat input varying from 30 to 60 kJ/cm, the microstructures were investigated by means of opt...The high strength bridge steel was processed with the simulated coarse grain heat affected zone（CGHAZ） thermal cycle with heat input varying from 30 to 60 kJ/cm, the microstructures were investigated by means of optical microscope（OM）, scanning electron microscope（SEM）, electron backscattering diffraction（EBSD） and transmission electron microscope（TEM）, and the impact properties were evaluated from the welding thermal cycle treated samples. The results indicate that the microstructure is primarily composed of lath bainite. With decreasing heat input, both bainite packet and block are significantly refined, and the toughness has an increasing tendency due to the grain refinement. The fracture surfaces all present cleavage or fracture for the samples with different heat inputs. Moreover, the average cleavage facet size for the CGHAZ is nearly equal to the average bainite packet size and the bainitic packet boundary can strongly impede the crack propagation, indicating that the bainitic packet is the most effective unit in control of impact toughness in the simulated CGHAZ of high strength bridge steel.展开更多
文摘The simulated heat affected zone （HAZ） of the high strength low alloy （HSLA） steels containing 0%, 0.047%, 0.097% and 0.151% vanadium, respectively, were studied with Gleeble-2000 thermomechanical simulator to determine the influence of vanadium addition on the mechanical properties of the HAZ. The HAZ simulation involved reheating the samples to 1350℃, and then cooling to ambient temperature at a cooling rate of 5℃/s ranging from 800 to 500℃ （△8/5=60s）. The mechanical properties including tensile strength and -20℃ impact toughness were conducted. The microstructures of the base steel and the simulated HAZs were investigated using optical microscope, scanning electron microscope （ SEM ） and transmission electron microscope （TEM）. Based on the systemutic examination, the present work confirmed that about 0.05% vanadium addition to low carbon low alloy steels resulted in expected balance of strength and toughness of the HAZ. And more than 0.10% levels addition led to detrimental toughness of the HAZ SEM study showed that the simulated 0.097% and 0.151%V HAZs consisted of more coarse ferrite plates with greater and more M-A constituents along austenite grain and ferrite plate bound- aries. The impact fracture surfaces of the simulated 0.097% and 0.151%V HAZs showed typically brittle mode with predominant cleavages. The size of the facet in the fracture surface increased with increasing vanadium level from 0.097% to 0.151%.As a result, the simulated 0.151% V HAZ has the lowest impact toughness of the four specimens.
基金Funded by Doctoral Scientific Research Foundation of Liao Ning Province(No.201601167)
文摘Microstructure evolution and impact toughness of simulated heat affected zone（HAZ） in low carbon steel have been investigated in this study. Thermal simulator was used to simulate microstructure evolution in HAZ with heat input of 10-100 kJ/cm welding thermal cycle. Results indicated that microstructure of HAZ mainly consisted of acicular ferrite（AF） inside grain and high volume fraction of grain boundaries ferrite（GBF） at prior austenite boundaries; the size of GBF and effective grain size increased with increasing heat input. Excellent impact toughness（more than 150 J at-40 ℃） was obtained in HAZ with heat input less than 50 k J/cm. When heat input was 100 kJ/cm, the impact toughness of HAZ decreased to 18 J because of the presence of large M-A constituent with lath-form in HAZ, assisting the micro-crack initiation and decreasing the crack initiation energy seriously. Effect of inclusions on acicular ferrite transformation in HAZ was also discussed.
文摘The relationship between the t8/5 and micro-hardness, impact toughness in the heat affected zone （HAZ） of ASME SA213-792 at peak temperature of 1 350 ℃ was studied by thermal simulation. The result shows that the micro-hardness of HAZ rises at the beginning and then decreases with increasing of t8/5 , whereas the impact toughness presents reverse trend. The distribution of precipitates in substrate has great influence on the impact toughness of HAZ. When the t8/5 is 40 s, chain-like precipitates lower the impact toughness of HAZ seriously.
基金Supported by the National 863 Program of China(No.2015AA042505)State Key Laboratory of Materials Processing and Die&Mould Technology of Huazhong University of Science and Technology(No.P2018-014)Major Science and Technology Project in Guangdong Province(No.2014B010130001)
文摘The high strength bridge steel was processed with the simulated coarse grain heat affected zone（CGHAZ） thermal cycle with heat input varying from 30 to 60 kJ/cm, the microstructures were investigated by means of optical microscope（OM）, scanning electron microscope（SEM）, electron backscattering diffraction（EBSD） and transmission electron microscope（TEM）, and the impact properties were evaluated from the welding thermal cycle treated samples. The results indicate that the microstructure is primarily composed of lath bainite. With decreasing heat input, both bainite packet and block are significantly refined, and the toughness has an increasing tendency due to the grain refinement. The fracture surfaces all present cleavage or fracture for the samples with different heat inputs. Moreover, the average cleavage facet size for the CGHAZ is nearly equal to the average bainite packet size and the bainitic packet boundary can strongly impede the crack propagation, indicating that the bainitic packet is the most effective unit in control of impact toughness in the simulated CGHAZ of high strength bridge steel.
