This paper proposes a design and implementation of the bi-directional DC-DC converter for Wind Energy Conversion System. The proposed project consists of boost DC/DC converter, bi-directional DC/DC converter (BDC), pe...This paper proposes a design and implementation of the bi-directional DC-DC converter for Wind Energy Conversion System. The proposed project consists of boost DC/DC converter, bi-directional DC/DC converter (BDC), permanent magnet DC generator and batteries. A DC-DC boost converter is interface with proposed wind system to step up the initial generator voltage and maintain constant output voltage. The fluctuation nature of wind makes them unsuitable for standalone operation. To overcome the drawbacks an energy storage device is used in the proposed system to compensate the fluctuations and to maintain a smooth and continuous power flow in all operating modes to load. Bi-directional DC-DC converter (BDC) is capable of transforming energy between two DC buses. It can operate as a boost converter which supplies energy to the load when the wind generator output power is greater than the required load power. It also operates in buck mode which charges from DC bus when output power is less than the required load power. The proposed converter reduces the component losses and increases the performance of the overall system. The complete system is implemented in MATLAB/SIMULINK and verified with hardware.展开更多
This paper explains step-by-step modeling and simulation of the full circuits of a battery control system and connected together starting from the AC input source to the battery control and storage system.The three-ph...This paper explains step-by-step modeling and simulation of the full circuits of a battery control system and connected together starting from the AC input source to the battery control and storage system.The three-phase half-controlled rectifier has been designed to control and convert the AC power into DC power.In addition,two types of direct current converters have been used in this paper which are a buck and bidirectional DC/DC converters.These systems adjust the output voltage to be lower or higher than the input voltage.In the buck converters,the main switch operates in conduction or cut-off mode and is triggered by a Pulse-Width Modulated(PWM)signal.The output and input voltage levels ratio are used to calculate thePWMsignal’s duty cycle.Therefore,the duty cycle indicates the operation mode of the converter in steady-state operation.In this study,we analyze and control of a buck converter with the PWM signal.Besides,the bidirectional DC/DC converter has been achieved and optimized by PI control methods to control the battery charging and discharging modes.The simulation has been applied via the Matlab/Simulink environment.The results show the activity of each part of the designed circuits starting from the converters and the battery control system in charge and discharge modes.展开更多
文摘This paper proposes a design and implementation of the bi-directional DC-DC converter for Wind Energy Conversion System. The proposed project consists of boost DC/DC converter, bi-directional DC/DC converter (BDC), permanent magnet DC generator and batteries. A DC-DC boost converter is interface with proposed wind system to step up the initial generator voltage and maintain constant output voltage. The fluctuation nature of wind makes them unsuitable for standalone operation. To overcome the drawbacks an energy storage device is used in the proposed system to compensate the fluctuations and to maintain a smooth and continuous power flow in all operating modes to load. Bi-directional DC-DC converter (BDC) is capable of transforming energy between two DC buses. It can operate as a boost converter which supplies energy to the load when the wind generator output power is greater than the required load power. It also operates in buck mode which charges from DC bus when output power is less than the required load power. The proposed converter reduces the component losses and increases the performance of the overall system. The complete system is implemented in MATLAB/SIMULINK and verified with hardware.
文摘This paper explains step-by-step modeling and simulation of the full circuits of a battery control system and connected together starting from the AC input source to the battery control and storage system.The three-phase half-controlled rectifier has been designed to control and convert the AC power into DC power.In addition,two types of direct current converters have been used in this paper which are a buck and bidirectional DC/DC converters.These systems adjust the output voltage to be lower or higher than the input voltage.In the buck converters,the main switch operates in conduction or cut-off mode and is triggered by a Pulse-Width Modulated(PWM)signal.The output and input voltage levels ratio are used to calculate thePWMsignal’s duty cycle.Therefore,the duty cycle indicates the operation mode of the converter in steady-state operation.In this study,we analyze and control of a buck converter with the PWM signal.Besides,the bidirectional DC/DC converter has been achieved and optimized by PI control methods to control the battery charging and discharging modes.The simulation has been applied via the Matlab/Simulink environment.The results show the activity of each part of the designed circuits starting from the converters and the battery control system in charge and discharge modes.
