Study and Production of a Two-Stage DC/DC DC/AC Converter for Generating an Alternating Voltage from a Direct Voltage Supplied by a Photovoltaic Array

This article presents an ongoing study of the design of a DC-AC inverter using a single renewable energy source. The proposed approach makes it possible to produce an output with an H-bridge or full bridge and a single energy source. To this end, the performance of the inverter was studied first by means of a simulation and then with the implementation of an experimental device.

An Adaptive Control Strategy for Energy Storage Interface Converter Based on Analogous Virtual Synchronous Generator

In the DC microgrid,the lack of inertia and damping in power electronic converters results in poor stability of DC bus voltage and low inertia of the DC microgrid during fluctuations in load and photovoltaic power.To address this issue,the application of a virtual synchronous generator(VSG)in grid-connected inverters control is referenced and proposes a control strategy called the analogous virtual synchronous generator(AVSG)control strategy for the interface DC/DC converter of the battery in the microgrid.Besides,a flexible parameter adaptive control method is introduced to further enhance the inertial behavior of the AVSG control.Firstly,a theoretical analysis is conducted on the various components of the DC microgrid,the structure of analogous virtual synchronous generator,and the control structure’s main parameters related to the DC microgrid’s inertial behavior.Secondly,the voltage change rate tracking coefficient is introduced to adjust the change of the virtual capacitance and damping coefficient flexibility,which further strengthens the inertia trend of the DC microgrid.Additionally,a small-signal modeling approach is used to analyze the approximate range of the AVSG’s main parameters ensuring system stability.Finally,conduct a simulation analysis by building the model of the DC microgrid system with photovoltaic(PV)and battery energy storage(BES)in MATLAB/Simulink.Simulation results from different scenarios have verified that the AVSG control introduces fixed inertia and damping into the droop control of the battery,resulting in a certain level of inertia enhancement.Furthermore,the additional adaptive control strategy built upon the AVSG control provides better and flexible inertial support for the DC microgrid,further enhances the stability of the DC bus voltage,and has a more positive impact on the battery performance.

DC-Link Capacitor Optimization in AC–DC Converter by Load Current Prediction

Alternating Current–Direct Current(AC–DC)converters require a high value bulk capacitor or afilter capacitor between the DC–DC conversion stages,which in turn causes many problems in the design of a AC–DC converter.The component package size for this capacitor is large due to its high voltage rating and capacitance value.In addition,the high charging current creates more pro-blems during the product compliance testing phase.The shelf life of these specific high value capacitors is less than that of Multilayer Ceramic Capacitors(MLCC),which limits its use for the highly reliable applications.This paper presents a fea-sibility study to overcome these two problems by adding a few sensing mechan-isms to the typical AC–DC converter topology.In majority of the AC–DC converter,Al-Elko capacitor takes approximately 3%to 5%of the converter size.The proposed method reduces this to approximately 50%size and so it effectively approximates 2%to 3%size reduction in converter size.The proposed method basically works based on the load current prediction method and hence it is highly suitable for the constant load application.Moreover,the converter response time increases in this method,which limit its application in high-speed systems.The high temperature application of Al-Elko capacitor is limited because of its poor performance,which is significantly rectified by replacing the Al-Elko with MLCC as it delivers good performance in high temperature.

Research on a Novel Inverter Based on DC/DC Converter Topology

The conventional inverters have the shortcomings of straightway conduction in transistors and the difficulty of realizing soft swit￣ching. A novel inverter based on the DC/DC converter topology is presented. The inverter is comprised of a combined Buck/Boost DC/DC converter and a bridge circuit. The front stage converter is controlled to output variable DC voltage and the bridge circuit is used to convert the DC voltage to AC output. The energy feedback technology and one circle control scheme are used t...

SIMULATION STUDY OF CHAOS IN DC-DC CONVERTER

A DC DC buck converter c on trolled by naturally sampled, constant frequency PWM is considered. The existe nce of chaotic solutions and the output performance of the system under differen t circuit parameters are studied. The transforming pattern of system behavior fr om steady state to chaotic is discovered by the cascades of period doubling bi furcation and the cascades of periodic orbit in V I phase space. Accordingl y, it is validated that change of values of the circuit parameters may lead DC DC converter to chaotic motion. Performances of the output ripples fro m steady state to chaotic are analyzed in time and frequency domains respective ly. Some important conclusions are helpful for opt imization design of DC DC converter.

基于回流功率优化的直流微网DC-DC变流器超螺旋滑模控制

针对直流微网系统中双有源桥直流变换器在系统发生扰动时动态特性差及在单移相调制下变换器效率不高等问题,该文在扩展移相调制下提出一种结合回流功率优化的超螺旋滑模控制策略。首先,分析双有源全桥(dual-active-bridge,DAB)变换器在扩展移相调制下两种模式的传输功率、回流功率数学模型及软开关特性,并以传输功率数学模型为基础建立DAB变换器的降阶模型。其次,以回流功率作为目标函数,以传输功率和软开关特性作为约束条件,通过Karush-Kuhn-Tucker(KKT)条件法寻找最优移相比组合;利用DAB变换器降阶模型设计超螺旋滑模控制中的等效部分,采用超螺旋算法作为切换部分,这两部分与内移相比D1共同作用生成外移相比D2,用于调节变换器的输出电压。最后进行了仿真及实验验证,实验结果表明:在负载投切、输入电压突变、参考电压改变时变换器具有良好的动态性能,同时能有效地减小回流功率。

基于单边调制映射函数的LCC-HVDC直流侧阻抗精确建模

阻抗模型是电网换相换流器型高压直流输电系统小信号稳定性分析的重要基础,阻抗模型的准确程度直接影响系统小扰动稳定性分析。该文首先从同步触发原理出发,引入基于单边调制产生的映射函数,该函数蕴含控制及换相信息,可以准确建立换相/非换相期间交直流侧的映射关系;其次,考虑换相动态并通过谐波线性化和傅里叶变换建立完整的直流侧电压和交流侧电流的频域小信号动态模型;再次,考虑控制和换流阀阻尼回路,建立整流侧和逆变侧直流阻抗解析模型;最后,以CIGRE高压直流标准测试模型为例,基于PSCAD/EMTDC平台验证了直流侧阻抗模型的准确性及其用于小扰动稳定性分析的有效性。

模块化高压大容量DC/DC变换器综述

随着新能源发电占比增加和电网规模的不断扩大,直流输电系统的容量不断提升,含有不同电压等级的直流电网是未来发展的必然趋势。在此背景下,DC/DC变换器作为直流电网关键设备,在多电压等级互联场景中发挥着重要作用。文中首先对已有的模块化高压大容量DC/DC变换器进行归纳、分类和比较,然后阐述了目前模块化高压大容量DC/DC变换器的拓扑结构、工作原理与特点,并针对其特点提出了不同变换器的适用场景,最后对未来的研究方向提出了建议。

Current Share Control IC Design for Paralleled DC/DC Converters

To keep even current distribution among DC/DC converters in a paralleled power system,an automatic master-slave control （AMSC） current sharing scheme is presented,which was implemented by a current share control IC. A current feedback loop for output voltage adjustment is proposed for low signal distortion. Moreover,a special startup control logic is designed to improve startup timing and to speed up the initial current sharing. It was completed in 1.5μm bipolar-CMOS-DMOS （BCD） technology with an area of 3.6mm^2 . Using it,a paralleled power system of two DC/DC converters capable of outputting 12V/3A was built. Experimental results show that the current sharing error at full load is kept within 1%.

基于移相控制统一模型的双有源桥DC-DC变换器基波环流优化控制策略

为充分利用双有源桥DC-DC变换器的容量,减小无功功率,提升工作效率,提出一种基于变换器移相控制统一模型的基波环流优化控制策略。通过引入基波移相比对变换器的所有移相控制方式进行统一描述,并采用傅里叶分解法建立全桥交流电压及电感电流的统一模型。该统一模型降低了多控制变量下变换器多模态分析的复杂性,适用于不同移相控制的所有工作模式,具有普适性。基于频域分析法和功率因数角,构建变换器传输功率及无功功率的统一数学模型。在此基础上,提出考虑无功基波分量的环流优化控制策略,并对传导损耗进行建模与分析。该策略简单有效,能够很好地减小变换器无功功率和改善系统效率,更有利于工程实际的应用。搭建了实验平台,对比了所提基波环流优化控制策略与传统移相控制方式下变换器的功率因数及变换效率,仿真和实验结果验证了理论分析的正确性和所提控制策略的可行性。

Extract the Output Signal Characteristics of DC-DC Converter Based on Fourier Descriptor

The precondition of realizing feedback controlling DC DC converter to avoid chaotic state is to judge the behavior of the converter and take corresponding measures. In this paper, the output signals under different circuit parameters of the PWM buck converter have been analyzed. The method of using Fourier descriptor to extract output signals characteristics is put forward and proved to be a gist of identifying and classifying the behavior of DC DC converter. This method can establish a good foundation fo...

基于时变权重模型预测的双向DC-DC优化控制方法

双向DC-DC变换器是电动汽车的关键电压变换部件,提高其动态负载下的响应速度与鲁棒性对电动汽车低压供电系统有重要意义。提出一种基于模糊时变权重的MPC(model predictive control)控制方法。基于状态空间平均法建立变换器动态模型。基于MPC原理搭建变换器MPC模型,实现对电压的跟踪控制;在分析权重对动态负载下电压跟踪性能的影响的基础上,设计权重模糊调节器,实现权重的在线调节。基于HM-cSPACE搭建实验平台验证所提方法的准确性。在Matlab/Simulink环境下与PI控制和传统MPC控制进行对比,结果表明:在负载变化时采用时变权重MPC控制的变换器有更好的动态性能和鲁棒性,超调量降低26.1%。该方法对提高双向DC-DC变换器动态负载下的优化控制具有重要意义。

一种交叉倍压型高增益DC/DC变换器

针对光伏发电、燃料电池发电等领域对高增益直流变换器的需求,以两相交错并联升压变换器为研究对象,由2个含有电感的倍压单元组合设计出实现电压提升的交叉倍压结构,据此提出了一种新颖的交叉倍压型高增益DC/DC变换器。该变换器可实现(3n+4)/(1-d)倍的高电压增益(1∶n为耦合电感匝数比,d为变换器占空比),且具有电路器件的低电压应力特性。对于漏感引起的开关管电压尖峰问题,引入了钳位电容构成释放漏感能量通道,同时提升了输出电压。介绍了新型交叉倍压型高增益变换器的拓扑结构,分析了变换器各模态的工作过程,推导了电压增益、输入电流纹波及各器件电压应力等稳态特性,并搭建样机进行实验研究,验证了该直流变换技术方案的可行性和先进性。

固态变压器中隔离双向DC/DC变换器扩展移相下虚拟电流控制策略

该文以固态变压器后级隔离双向DC/DC变换器为重点研究对象,提出一种扩展移相下虚拟电流控制策略。通过分析后级变换器在扩展移相传输功率下相移量关系以获得最小电流应力最优解来提高变换器的传输效率,减少器件损耗。同时通过虚拟电流控制思想在线估算传输功率来提高系统动态响应性能,减少电流传感器使用。最后,对该文所提出的扩展移相下虚拟电流控制与扩展移相控制进行实验对比分析,验证了扩展移相下虚拟电流控制策略具有降低电流应力,显著提高变换器的动态响应的优点。

三有源桥DC-DC变换器广义状态空间平均模型及控制策略研究

基于移相加占空比控制策略的三有源桥TAB(triple active bridge)DC-DC变换器具有效率高和软开关范围可扩展等优点,但其小信号建模过程复杂、闭环控制环路参数整定困难。针对该问题,提出1种TAB工作在移相加占空比控制下的全阶连续广义状态平均建模和PI控制器设计方法。首先,分析TAB的运行原理和Y型等效结构;然后,结合移相加占空比控制的特点和交流方波源等效方法,推导出TAB的广义状态空间平均模型;接着,在推得模型的基础上求得输入到输出的传递函数,设计出PI控制器参数。最后,结合数字仿真及样机实验验证了所提方法的正确性及有效性。

基于改进LSTM-SVM的双向DC-DC电力变换器故障诊断

目的为了解决双向DC-DC电力变换器的软故障诊断精度不高的问题,方法提出基于改进LSTM-SVM的双向DC-DC电力变换器故障诊断模型。首先,分析双向DC-DC电力变换器中电容、电感和MOSFET管的故障机理,通过仿真实验模拟各元件失效后变换器的输出电气参数变化,从而确定变换器不同元件故障时对应的故障特征参数;其次,构建改进的LSTM-SVM双向DC-DC电力变换器故障诊断组合模型,在LSTM中添加Mogrifier门机制,提高LSTM提取时间序列原始数据中微弱特征的能力;最后,由于传统LSTM的末端分类器为Softmax,其主要解决单一元件诊断问题,变换器故障类型较多,维数较高,所以采用麻雀搜索算法优化的SVM代替原有的Softmax函数,对LSTM输出的数据进行故障分类,提高故障诊断的准确率。设置双向DC-DC电力变换器充放电两种状态下,包含电解电容、电感和MOSFET单双管故障在内的24组故障,分别采用本文构建的改进的LSTM-SVM和原始的LSTM-SVM双向DC-DC变换器故障诊断模型进行诊断。结果结果表明,改进的LSTM-SVM故障诊断模型诊断准确率平均值为99.71%,原始的LSTM-SVM故障诊断模型诊断准确率平均值为88.48%,改进的LSTM-SVM故障诊断模型对各元件的故障诊断正确率均高于原始的LSTM-SVM故障诊断模型的。结论基于改进LSTM-SVM的双向DC-DC电力变换器故障诊断模型实现了对双向DC-DC电力变换器中的电解电容、电感和MOSFET单双管故障的准确诊断。

一种可拓展双输入高增益DC/DC变换器

针对光伏发电系统中光伏电池板集成汇流的需求,提出了一种可拓展双输入高增益DC/DC变换器。该变换器采用了一种新型拓扑结构,可在实现输入输出电压高增益变换的同时降低了开关器件的电压应力。此外,所提变换器还具有可拓展性,可以根据不同的光伏电池板数量和输出电压要求对端口进行扩展,从而降低系统的复杂性和成本。首先详细介绍了所提变换器的拓扑结构,并推导出变换器在不同工作模态下的运行原理。然后,对该变换器的增益特性、开关器件的电压和电流应力、关键器件的参数选择和损耗计算等方面进行了深入的理论分析。最后,搭建了一台输出功率为1 kW的实验样机,并进行了实验测试。实验结果验证了所提变换器理论分析的正确性和可行性。

基于SEPIC的新型高增益DC-DC变换器及衍生拓扑分析

针对光伏并网系统中单开关升压变换器(如SEPIC、Boost、准Z源、二次型)电压增益低和半导体器件电压应力大的问题,提出1种基于SEPIC的外部升压型高增益DC-DC变换器。首先对所提变换器在电感电流连续导通模式和断续导通模式下的工作原理和稳态特性进行详细分析,并与其他新型拓扑进行性能对比。在此基础上,给出了基于外部升压网络的衍生拓扑。最后,通过搭建1台400 V/200 W的实验样机证明了理论分析的准确性。所提变换器利用阻抗网络和开关电容单元构成的外部升压网络提升了SEPIC变换器的电压增益,并改善了半导体器件电压应力大的缺点。

一种新型准Z源高增益DC-DC升压变换器

针对传统准Z源阻抗网络DC-DC升压变换器存在电压增益低和元件电压应力高的问题,提出一种新型准Z源高增益DC-DC升压变换器(HSQZSC)。首先,分析HSQZSC变换器两种模态工作原理,并对其进行稳态分析和参数设计。其次,与现已提出的Z源变换器进行性能对比,表明HSQZSC变换器具有高电压增益和元件电压应力低的优势。然后,对其建立状态空间模型进行小信号分析、稳定性分析和控制器的设计。最后,搭建100 W实物样机,实验结果验证了HSQZSC变换器的可行性与有效性。

基于LLC谐振变换器的双向DC-DC光伏储能回路设计

针对光储逆变器的储能回路效率较低,控制较为复杂等问题,该文设计了一款基于双向全桥LLC谐振变换器的双向储能电路。对双向全桥LLC谐振变换器的正向导通特性和反向导通特性进行介绍和分析,基于采用基波分析法得到的LLC谐振变换器等效电路,推导出变换器实现软开关的条件。通过推导得到的条件对LLC谐振变换器进行硬件参数设计,并成功搭建一台样机进行实验验证,实验结果表明,变换器可以在全负载领域实验软开关,并具有较高的效率,验证了理论分析的正确性。