To increase the detectability of split Hopkinson pressure bar （SHPB） of low-impedance materials, modifications were conducted on traditional SHPB apparatus with a PMMA tube to output transmitted signal, and weak sig...To increase the detectability of split Hopkinson pressure bar （SHPB） of low-impedance materials, modifications were conducted on traditional SHPB apparatus with a PMMA tube to output transmitted signal, and weak signals were further amplified by semiconductor strain gauges. Experiments on soft rubbers and cushioning foam materials were carried out. In order to analyze the accuracy of the experimental results, the stress equilibrium issues involved in the assumptions of SHPB were investigated. First, by way of re-constructing loading process of incident wave, the stress- strain curve was obtained, along with the stress equilibrium ratio of specimen. Secondly, the influences on the accuracy of stress-strain curves were investigated through the elastic modulus comparisons. And the results illustrate that the bilinear incident wave from experiments can ensure the stress equilibrium deformation of specimen after 2 normalized times, much sooner than ramp incident waves. Moreover, it even facilitates specimen deformation with a constant strain rate. The results confirm that the detectability of the modified SHPB can be down to tens kPa with enough accuracy level.展开更多
In the present study, the indentation testing with a flat cylindrical indenter on typical multi-layer material systems was simulated successfully by finite element method. The emphasis was put on the methods of extrac...In the present study, the indentation testing with a flat cylindrical indenter on typical multi-layer material systems was simulated successfully by finite element method. The emphasis was put on the methods of extracting the yield stresses and strain-hardening modulus of upper and middle-layers of three-layer material systems from the indentation testing. The slope of the indentation depth to the applied indentation stress curve was found to have a turning point, which can be used to determine the yield stress of the upper-layer. Then, a different method was also presented to determine the yield stress of the middle-layer. This method was based on a set of assumed applied indentation stresses which were to be intersected by the experimental results in order to meet the requirement of having the experimental indentation depth. At last, a reverse numerical algorithm was explored to determine the yield stresses of upper and middle-layers simultaneously by using the indentation testing with two different size indenters. This method assumed two ranges of yield stresses to simulate the indentation behavior. The experimental depth behavior was used to intersect the simulated indentation behavior. And the intersection corresponded to the values of yield stresses of upper and middle-layers. This method was also used further to determine the strain-hardening modulus of upper and middle-layers simultaneously.展开更多
The stress-strain curve of bending bar and the stress relax curve of AZ31 was obtained by a tension test using Gleeble-1500.The tension straightening process mainly consisted of the elastic loading-I and unloading sta...The stress-strain curve of bending bar and the stress relax curve of AZ31 was obtained by a tension test using Gleeble-1500.The tension straightening process mainly consisted of the elastic loading-I and unloading stage,the elastic loading-II and unloading stage,and the elastic-plastic loading stage,which were based on the stretch force change during straightening.The circular bar straightening under one-dimensional bending was investigated and assumed to be linear strain-hardening elastic-plastic material.According to the elastic-plastic mechanics theory,the mathematical displacement-force model of a tension straightening process established,on which was based,the predicted displacement of tension straightening for various original deflection was calculated.The tension straightening experiment for AZ31 magnesium was conducted under the guidance of the predicted displacement.The experiment results present good straightness when there is a stress relaxation phenomenon or the temperature of tension straightening is 25℃.展开更多
基金Supported by the National Natural Science Foundation(11272267,11102168,10932008)111 Project(B07050)
文摘To increase the detectability of split Hopkinson pressure bar （SHPB） of low-impedance materials, modifications were conducted on traditional SHPB apparatus with a PMMA tube to output transmitted signal, and weak signals were further amplified by semiconductor strain gauges. Experiments on soft rubbers and cushioning foam materials were carried out. In order to analyze the accuracy of the experimental results, the stress equilibrium issues involved in the assumptions of SHPB were investigated. First, by way of re-constructing loading process of incident wave, the stress- strain curve was obtained, along with the stress equilibrium ratio of specimen. Secondly, the influences on the accuracy of stress-strain curves were investigated through the elastic modulus comparisons. And the results illustrate that the bilinear incident wave from experiments can ensure the stress equilibrium deformation of specimen after 2 normalized times, much sooner than ramp incident waves. Moreover, it even facilitates specimen deformation with a constant strain rate. The results confirm that the detectability of the modified SHPB can be down to tens kPa with enough accuracy level.
基金the National Natural Science Foundation of China （No. 10472094） the Research Fund for the Doctoral Program of Higher Education （N6CJ0001） Doctorate Fund of Northwestern Polytechnical University.
文摘In the present study, the indentation testing with a flat cylindrical indenter on typical multi-layer material systems was simulated successfully by finite element method. The emphasis was put on the methods of extracting the yield stresses and strain-hardening modulus of upper and middle-layers of three-layer material systems from the indentation testing. The slope of the indentation depth to the applied indentation stress curve was found to have a turning point, which can be used to determine the yield stress of the upper-layer. Then, a different method was also presented to determine the yield stress of the middle-layer. This method was based on a set of assumed applied indentation stresses which were to be intersected by the experimental results in order to meet the requirement of having the experimental indentation depth. At last, a reverse numerical algorithm was explored to determine the yield stresses of upper and middle-layers simultaneously by using the indentation testing with two different size indenters. This method assumed two ranges of yield stresses to simulate the indentation behavior. The experimental depth behavior was used to intersect the simulated indentation behavior. And the intersection corresponded to the values of yield stresses of upper and middle-layers. This method was also used further to determine the strain-hardening modulus of upper and middle-layers simultaneously.
基金Sponsored by National Great Theoretic Research Project(2013CB632200)National Sci&Tech Support Project(2011BAE22B01-3)International Cooperation Project(2010DFR50010).
文摘The stress-strain curve of bending bar and the stress relax curve of AZ31 was obtained by a tension test using Gleeble-1500.The tension straightening process mainly consisted of the elastic loading-I and unloading stage,the elastic loading-II and unloading stage,and the elastic-plastic loading stage,which were based on the stretch force change during straightening.The circular bar straightening under one-dimensional bending was investigated and assumed to be linear strain-hardening elastic-plastic material.According to the elastic-plastic mechanics theory,the mathematical displacement-force model of a tension straightening process established,on which was based,the predicted displacement of tension straightening for various original deflection was calculated.The tension straightening experiment for AZ31 magnesium was conducted under the guidance of the predicted displacement.The experiment results present good straightness when there is a stress relaxation phenomenon or the temperature of tension straightening is 25℃.
