A series of fluorescent composites were prepared by blending silicone rubber with Eu(TTA )2(phen)(MA). The influence of mechanical blending temperature on fluorescent intensity of composites and dispersion of rare ear...A series of fluorescent composites were prepared by blending silicone rubber with Eu(TTA )2(phen)(MA). The influence of mechanical blending temperature on fluorescent intensity of composites and dispersion of rare earth complexes in the SiR matrix were investigated. As for the cured rubber, it is found that its fluorescent intensity is relatively low compared with that of uncured rubber. Low temperature is beneficial to dispersion of Eu(TTA )2(phen)(MA) homogeneously. When the amount of rare earth complexes is low, the fluorescent intensity of composites prepared by mechanical blending method above melting point of Eu(TTA )2(phen)(MA) is much higher than that of composites prepared below melting point.展开更多
Bi 0.5 Sb 1.5 Te 3/polyaniline composites were prepared by mechanical blending and in situ polymerization, and their transport properties were measured. It was found that for the composites with 1%, 3%, 5% and 7% poly...Bi 0.5 Sb 1.5 Te 3/polyaniline composites were prepared by mechanical blending and in situ polymerization, and their transport properties were measured. It was found that for the composites with 1%, 3%, 5% and 7% polyaniline (mass fraction) respectively, which were prepared by mechanical blending, the power factors decrease by about 30%, 50%, 55% and 65% compared with the Bi 0.5 Sb 1.5 Te 3 samples, which is mainly due to the remarkable decreases of the electrical conductivity. The electrical conductivity and power factor of the composites samples with 7% polyaniline prepared by in situ polymerization are higher by about 65% and 60%, respectively, than that of the corresponding samples prepared by mechanical blending.展开更多
The physical and mechanical properties of blends composed of two kinds of epoxy resins of different numbers of functional groups and chemical structure were studied. One of the resins was a bifunctional epoxy resin ba...The physical and mechanical properties of blends composed of two kinds of epoxy resins of different numbers of functional groups and chemical structure were studied. One of the resins was a bifunctional epoxy resin based on diglycidyl ether of bisphenol A and the other resin was a multifunctional epoxy novolac resin. Attempt was made to establish a correlation between the structure and the final properties of cured epoxy samples. The blend samples containing high fraction of multifunctional epoxy resin showed higher solvent resistance and lower flexural modulus compared with the blends containing high fraction of bifunctional epoxy resin. The epoxy blends showed significantly higher ductility under bending test than the neat epoxy samples. The compressive modulus and strength increased with increasing of multifunctional epoxy in the samples, probably due to enhanced cross-link density and molecular weight. Morphological analysis revealed the presence of inhomogeneous sub-micrometer structures in all samples. The epoxy blends exhibited significantly higher fracture toughness（by 23% at most） compared with the neat samples. The improvement of the fracture toughness was attributed to the stick-slip mechanism for crack growth and activation of shear yielding and plastic deformation around the crack growth trajectories for samples with higher content of bifunctional epoxy resin as evidenced by fractography study.展开更多
基金Project supported by the National Natural Science Foundation of China and the China Energy Conservation Investment Corporation (50173004 and 50503002)the Beijing New Star Project (2003A11)+1 种基金the National High-Tech Research Developing Foundation ("863", 2003AA324030) Beijing Municipal Commission of Education (JD100100403)
文摘A series of fluorescent composites were prepared by blending silicone rubber with Eu(TTA )2(phen)(MA). The influence of mechanical blending temperature on fluorescent intensity of composites and dispersion of rare earth complexes in the SiR matrix were investigated. As for the cured rubber, it is found that its fluorescent intensity is relatively low compared with that of uncured rubber. Low temperature is beneficial to dispersion of Eu(TTA )2(phen)(MA) homogeneously. When the amount of rare earth complexes is low, the fluorescent intensity of composites prepared by mechanical blending method above melting point of Eu(TTA )2(phen)(MA) is much higher than that of composites prepared below melting point.
文摘Bi 0.5 Sb 1.5 Te 3/polyaniline composites were prepared by mechanical blending and in situ polymerization, and their transport properties were measured. It was found that for the composites with 1%, 3%, 5% and 7% polyaniline (mass fraction) respectively, which were prepared by mechanical blending, the power factors decrease by about 30%, 50%, 55% and 65% compared with the Bi 0.5 Sb 1.5 Te 3 samples, which is mainly due to the remarkable decreases of the electrical conductivity. The electrical conductivity and power factor of the composites samples with 7% polyaniline prepared by in situ polymerization are higher by about 65% and 60%, respectively, than that of the corresponding samples prepared by mechanical blending.
文摘The physical and mechanical properties of blends composed of two kinds of epoxy resins of different numbers of functional groups and chemical structure were studied. One of the resins was a bifunctional epoxy resin based on diglycidyl ether of bisphenol A and the other resin was a multifunctional epoxy novolac resin. Attempt was made to establish a correlation between the structure and the final properties of cured epoxy samples. The blend samples containing high fraction of multifunctional epoxy resin showed higher solvent resistance and lower flexural modulus compared with the blends containing high fraction of bifunctional epoxy resin. The epoxy blends showed significantly higher ductility under bending test than the neat epoxy samples. The compressive modulus and strength increased with increasing of multifunctional epoxy in the samples, probably due to enhanced cross-link density and molecular weight. Morphological analysis revealed the presence of inhomogeneous sub-micrometer structures in all samples. The epoxy blends exhibited significantly higher fracture toughness（by 23% at most） compared with the neat samples. The improvement of the fracture toughness was attributed to the stick-slip mechanism for crack growth and activation of shear yielding and plastic deformation around the crack growth trajectories for samples with higher content of bifunctional epoxy resin as evidenced by fractography study.
