Investigations on High-Speed Flash Boiling Atomization of Fuel Based on Numerical Simulations

Flash boiling atomization(FBA)is a promising approach for enhancing spray atomization,which can generate a fine and more evenly distributed spray by increasing the fuel injection temperature or reducing the ambient pressure.However,when the outlet speed of the nozzle exceeds 400 m/s,investigating high-speed flash boiling atomization(HFBA)becomes quite challenging.This difficulty arises fromthe involvement ofmany complex physical processes and the requirement for a very fine mesh in numerical simulations.In this study,an HFBA model for gasoline direct injection(GDI)is established.This model incorporates primary and secondary atomization,as well as vaporization and boilingmodels,to describe the development process of the flash boiling spray.Compared to lowspeed FBA,these physical processes significantly impact HFBA.In this model,the Eulerian description is utilized for modeling the gas,and the Lagrangian description is applied to model the droplets,which effectively captures the movement of the droplets and avoids excessive mesh in the Eulerian coordinates.Under various conditions,numerical solutions of the Sauter mean diameter(SMD)for GDI show good agreement with experimental data,validating the proposed model’s performance.Simulations based on this HFBA model investigate the influences of fuel injection temperature and ambient pressure on the atomization process.Numerical analyses of the velocity field,temperature field,vapor mass fraction distribution,particle size distribution,and spray penetration length under different superheat degrees reveal that high injection temperature or low ambient pressure significantly affects the formation of small and dispersed droplet distribution.This effect is conducive to the refinement of spray particles and enhances atomization.

A Novel Numerical Method for Simulating Boiling Heat Transfer of Nanofluids

In this paper,a new approach called the Eulerian species method was proposed for simulating the convective and/or boiling heat transfer of nanofluids.The movement of nanoparticles in nanofluids is tracked by the species transport equation,and the boiling process of nanofluids is computed by the Eulerian multiphase method coupled with the RPI boiling model.The validity of the species transport equation for simulating nanoparticles movement was verified by conducting a simulation of nanofluids convective heat transfer.Simulation results of boiling heat transfer of nanofluids were obtained by using the commercial CFD software ANSYS Fluent and compared with experimental data and results from another numerical method(Eulerian three-phase model).Good agreement with experimental data was achieved,and it was proved the Eulerian species method is better than the Eulerian three-phase model since it can give better simulation results with higher accuracy but needs fewer computation resources.

Effect of the Geometrical Parameter of OpenMicrochannel on Pool Boiling Enhancement

High heat dissipation is required for miniaturization and increasing the power of electronic systems.Pool boiling is a promising option for achieving efficient heat dissipation at low wall superheat without the need for moving parts.Many studies have focused on improving heat transfer efficiency during boiling by modifying the surface of the heating element.This paper presents an experimental investigation on improving pool boiling heat transfer using an open microchannel.The primary goal of this work is to investigate the impact of the channel geometry characteristics on boiling heat transfer.Initially,rectangular microchannels were prepared on a circular copper test piece with a diameter of 20 mm.Then,the boiling characteristics of these microchannels were compared with those of a smooth surface under saturated conditions using deionized water.In this investigation,a wire-cutting electrical discharge machine(EDM)machine was used to produce parallel microchannels with channel widths of 0.2,0.4,and 0.8 mm.The fin thicknesses were 0.2,0.4,and 0.6 mm,while the channel depth remained constant at 0.4 mm.The results manifested that the surface featuring narrower fins and broader channels achieved superior performance.The heat transfer coefficient(HTC)was enhanced by a maximum of 248%,and the critical heat flux(CHF)was enhanced by a maximum of 101%compared to a plain surface.Eventually,the obtained results were compared with previous research and elucidated a good agreement.

Experimental Study on the Bubble Dynamics of Magnetized Water Boiling

Boiling heat transfer,as an efficient heat transfer approach,that can absorb a large amount of latent heat during the vaporization,is especially suitable for heat transfer occasions with high heat flux demands.Experimental studies show that the surface tension coefficient of pure water can be reduced sharply(up to 25%)when it is magnetized by amagnetic field applied externally.In this paper,magnetized water(MW)was used as the work fluid to conduct boiling heat transfer experiments,to explore the influence of magnetization on the boiling characteristics of pure water.The electromagnetic device was used to magnetize water,and then the MW was used as the work-fluid of boiling heat transfer experiments,the bubble dynamic behavior of the MW boiling was captured by a video camera,and the characteristics andmechanism were analyzed.It was found that at the same conditions,the boiling of MW can produce more vapor bubbles of smaller size than the water without magnetization,which leads to a higher heat-transfer efficiency.This indicates that magnetization can enhance the boiling heat transfer of pure water.Furthermore,the thermal conditions required by magnetized water when the boiling is started are lower than the non-magnetized water boiling,whichmeans the earlier start of nucleate pool boiling when using the MW.

Effect of Gd on neutron absorption properties and electrochemical corrosion behavior of Zr-Gd alloy in boiling concentrated HNO3

A Zr-Gd alloy with neutron poisoning properties and resistance to boiling concentrated HNO3 corrosion was developed based on a corrosion-resistant Zr-702 alloy to meet the demand for neutron shielding in the closed-loop treatment of spent fuel and the nuclear chemical industry.In this study,1 wt.%,3 wt.%,5 wt.%,7 wt.%,and 9 wt.%Zr-Gd alloys were designed and fabricated with Zr-702 as the control element.The electrochemical behavior of the Zr-Gd alloys in boiling concentrated HNO3 was investigated,and the neutron shielding effect on plate thickness and Gd content was simulated.The experimental results demonstrate that the corrosion resistance of the alloy decreased slightly before~7-9 wt.%with increasing Gd content;this is the inflection point of its corrosion resistance.The alloy uniformly dissolved the Gd content that could not be dissolved in the Zr lattice,resulting in numerous micropores on the passivation coating,which deteriorated and accelerated the corrosion rate.The MCNP simulation demonstrated that when the Gd content was increased to 5 wt.%,a 2-mm-thick plate can shield 99.9%neutrons;an alloy with a Gd content≥7 wt.%required only a 1-mm-thick plate,thereby showing that the addition of Gd provides an excellent neutron poisoning effect.Thus,the corrosion resistance and neutron shielding performance of the Zr-Gd alloy can meet the harsh service requirements of the nuclear industry.

Simulation of single bubble dynamic process in pool boiling process under microgravity based on phase field method

We use the phase field method to track the gas-liquid interface based on the gas-liquid two-phase flow in the pool boiling process,and study the bubble nucleation,growth,deformation,departure and other dynamic behaviors on the heating surface under microgravity.By simulating the correlation between liquid undercooling and bubble dynamics,we find that the bubble growth time increases with the increase of liquid undercooling,but the effect of liquid undercooling on bubble height is not significant.Meanwhile,the gas-liquid-solid three-phase contact angle and the gravity level will also have an effect on the bubble growth time and bubble height.With the increase of the contact angle,the bubble growth time and bubble height when the bubble departs also increase.While the effect of gravity level is on the contrary,the smaller the gravity level is,the larger the bubble height and bubble growth time when the bubble separates.

Experimental and Numerical Analysis of the Influence ofMicrochannel Size and Structure on Boiling Heat Transfer

Computational fluid dynamics was used and a numerical simulation analysis of boiling heat transfer in microchannels with three depths and three cross-sectional profiles was conducted.The heat transfer coefficient and bubble generation process of three microchannel structures with a width of 80μm and a depth of 40,60,and 80μm were compared during the boiling process,and the factors influencing bubble generation were studied.A visual test bench was built,and test substrates of different sizes were prepared using a micro-nano laser.During the test,the behavior characteristics of the bubbles on the boiling surface and the temperature change of the heated wall were collected with a high-speed camera and a temperature sensor.It was found that the microchannel with a depth of 80μm had the largest heat transfer coefficient and shortest bubble growth period,the rectangular channel had a larger peak heat transfer coefficient and a lower frequency of bubble occurrence,while the V-shaped channel had the shortest growth period,i.e.,the highest frequency of bubble occurrence,but its heat transfer coefficient was smaller than that of the rectangular channel.

Lattice Boltzmann simulation of the effects of cavity structures and heater thermal conductivity on nucleate boiling heat transfer

The boiling heat transfer technology with cavity surfaces can provide higher heat flux under lower wall superheat,which is of great significance for the cooling of electronic chips and microelectromechanical devices.In this paper,the boiling characteristics of the cavity surfaces are investigated based on the lattice Boltzmann(LB)method,focusing on the effects of cavity shapes,sizes,and heater thermal conductivity on the heat transfer performance.The results show that the triangular cavity has the best boiling performance since it has less residual vapor and higher bubble departure frequency than those of the trapezoidal and rectangular cavities.As the cavity size increases,the enhancement of heat transfer by the cavity mouth is suppressed by the heat accumulation effect at the heater bottom.The liquid rewetting process during bubble departure is the reason for the fluctuation of the space-averaged heat flux,and the heater thermal conductivity determines the fluctuation amplitude.The evaporation of liquid in the cavity with high thermal conductivity walls is more intense,resulting in shorter waiting time and higher bubble departure frequency.

Comparisons of Structured Surface Floors for Pool Boiling Enhancement at Low Heat Fluxes: Hands-On Learning Setup for Heat Transfer Classroom

Various enhanced surfaces have been proposed over the years to improve boiling heat transfer. This paper introduces an experimental setup designed for boiling demonstration in the graduate-level Heat Transfer course. The pool boiling performance of water under atmospheric pressure of 1.025 bar is investigated by using several structured surfaces at heat fluxes of 28 and 35 kW/m2. Surfaces with holes, rectangular grooves, and mushroom fins are manufactured by an NC-controlled vertical milling machine. The heat flux versus excess temperature graph is plotted by using thermocouple measurements of water and base temperatures of the boiling vessel. The separation, rise, and growth of individual vapor bubbles from the surface during boiling were recorded with a digital camera. The results for the plain surface are compared to the Rohsenow correlation. The enhancement of heat transfer coefficient (h) ranged between 15% - 44.5% for all structured surfaces. The highest heat transfer coefficient enhancement is observed between 41% - 56.5% for holed surface-3 (405 holes) compared to the plain surface. The excess temperature dropped around 29% - 34% for holed surface-3 (405 holes) compared to the plain surface. The heat transfer coefficient increases as the spacing between channels or holes decreases. While the bubbles on holed and mushroomed surfaces were spherical, the bubbles on the flat and grooved surfaces were observed as formless. The suggested economical test design could be appropriate to keep students focused and participating in the classroom.

The‘New Normal’of Extreme Weather And the Urgency of Transformation“The era of global warming is over and the era of global boiling has arrived.”

Phong,a 42-year-old Vietnamese motorcyclist begins his busy day at 5 a.m.In Hanoi,light motorcycles are an important mode of transportation.Countless motorcycles shuttle through the streets and alleys of the city,transporting parcels,goods,and passengers to various destinations.Phong usually works for 12 hours straight with little rest.However,the unprecedented heat waves this summer had often pushed daytime temperatures to above 40 degrees Celsius,making it extremely difficult for Phong to complete his daily routine.Phong prepared a hat,a wet handkerchief,and more drinking water.He even installed a small umbrella above his mobile phone rack to prevent the phone from overheating in the sun because it is his only source of work.Despite all the equipment,he is still worried.“If I suffer heat stroke or anything else,I will be unable to work,”he said.“I can’t afford it.”

A new heat transfer correlation for flow boiling in helically coiled tubes

Based on the superposition principle of the nucleate boiling and convective heat transfer terms,a new correlation is developed for flow boiling heat transfer characteristics in helically coiled tubes.The effects of the geometric and system parameters on heat transfer characteristics in helically coiled tubes are investigated by collecting large amounts of experimental data and analyzing the heat transfer mechanisms. The existing correlations are divided into two categories,and they are calculated with the experimental data.The Dn factor is introduced to take into account the effect of a complex geometrical structure on flow boiling heat transfer.A new correlation is developed for predicting the flow boiling heat transfer coefficients in the helically coiled tubes,which is validated by the experimental data of R134a flow boiling heat transfer in them;and the average relative error and root mean square error of the new correlation are calculated.The results show that the new correlation agrees well with the experimental data,indicating that the new correlation can be used for predicting flow boiling heat transfer characteristics in the helically coiled tubes.

Pool boiling performance of porous surface tubes under vacuum conditions

Two types of tube bundles are designed,which are,respectively,composed of six tubes arranged in the boiling chamber.The nucleate pool boiling performance of smooth tube bundles and sintered porous surface tube bundles with deionized water as a medium are experimentally studied at atmospheric and sub-atmospheric pressures,respectively.The experimental results indicate that the boiling heat transfer coefficients of the two types of tube bundles increase with the increase in pressure under vacuum conditions as they behave under ordinary pressure.As the pressure varies from 10 to 100 kPa,it also can be seen that the heat transfer coefficient of the sintered porous surface tube is increased by 0.2 to 4 times compared with the smooth one under the same operating parameters.In addition,the experimental data show that a definite bundle effect exists in both sintered porous surface tubes and smooth tubes under vacuum conditions.

Preparation and characteristic analysis of rice husk high boiling solvent lignin

Rice husk high boiling solvent lignin （RHL） was prepared by high boiling solvent method, and its characteristics was analyzed by using chemical composition analysis, infrared spectroscopy, and ^1H-NMR and ^13C-NMR spectroscopy. The optimum prepared condition was that the rice husk with 70%-90% aqueous solution of 1, 4-butanediol was mixed with autoclave, under a certain weight ratio of solid raw material and solvent, heated to 200-220℃ for 1.0-3.0 h, then water-insoluble RHL was separated from the liquor reaction mixture by water precipitation. Results suggested that the lower digestion temperature and concentration of 1,4-butanediol were both unfavorable for extracting lignin. Chemical weight-average molecular weight of RHL was 1939 g·mol^-1, and the residual polysaccharide content was 5.12%. The ^1H-NMR spectra of RHL showed the relative intensity ratio, aliphatic over aromatic methoxyl groups, situated at 3.5-3.8 and 3.8-4.0 ppm, respectively. The results from ^13C-NMR spectra showed that β-O-4 bond and β-5 carbon-carbon linkage were the major linkages between RHL units. The C9-formula of RHL was calculated by the experiment data.

Geology and mineralization of the Dongping supergiant alkalic-hosted Au-Te deposit(>100 t Au)in Northern Hebei Province,China:A review

The Dongping deposit is the largest alkalic-hosted gold deposit in China containing>100 t of Au.This paper presents a new understanding for Dongping ore system,based on the previous studies.The mineralization originally occurred at 400-380 Ma,simultaneous with emplacement of the Shuiquangou alkaline complex,and was overprinted by the hydrothermal activity in the Yanshanian.Isotope compositions of ores indicate metals of the deposit are mainly provided by the Shuiquangou complex.Ore-forming fluids are characterized by increasing oxygen fugacity and decreasing sulfur fugacity,while tellurium fugacity increased in the Stage II-2 and decreased in Stage II-3.These systematic changes are closely related to the processes of mineral precipitation and fluid evolution.Sulfide precipitation from Stage Ⅰ to Stage Ⅱ was triggered by fluid boiling,which leads to the precipitation of Pb-Bi-Te,due to decrement of sulfur fugacity.Condensation of gas phase containing high concentration of H_2Te leads to precipitation of Te-Au-Ag minerals and native tellurium.Based on these hypotheses,this paper present a polyphase metallogenic model as follow.During the Devonian,fluids were released from alkaline magmas,which carried ore-forming materials form the surrounding rocks and precipitate the early ores.During the Jurassic-Cretaceous,fluorine-rich fluids exsolved from highly factionated Shangshuiquan granite,which extracted and concentrated Au from the Shuiquangou complex and the Sanggan Group metamorphic rocks,and finally formed the Dongping gold deposit.

Hustle and Bustle along the Central Axis——30 Years of Photographing Hutongs in Beijing

NO one can precisely describe Beijing with a single word or sentence due to its extreme complexity.Every passenger who arrives in Beijing by plane is welcomed by an ocean of light.The light resembles boiling magma,flowing along a layout of the city in an orderly manner.If Chang’an Avenue,Sanlitun,China World Trade Center,and National Olympic Sports Center are highlights of Beijing,the hutong s(lanes)distributed along the Central Axis represent the other side of the capital city.They tell the stories of this city and its citizens with a subtler voice.In these places where the city’s neon lights cannot reach,the essence of the city’s daily life exists in a small restaurant,a tanghulu(a traditional Chinese snack of candied fruit),or even a bowl of fermented soybean drink.

Position Group Contribution Method for Predicting the Normal Boiling Point of Organic Compounds

A new position group contribution model is proposed for the estimation of normal boiling data of organic compounds involving a carbon chain from C2 to C18.The characteristic of this method is the use of position distribution function.It could distinguish most of isomers that include cis-or trans-structure from organic compounds.Contributions for hydrocarbons and hydrocarbon derivatives containing oxygen,nitrogen,chlorine,bromine and sulfur,are given.Compared with the predictions,results made use of the most common existing group contribution methods,the overall average absolute difference of boiling point predictions of 417 organic compounds is 4.2 K;and the average absolute percent derivation is 1.0%,which is compared with 12.3 K and 3.2% with the method of Joback,12.1 K and 3.1% with the method of Constantinou-Gani.This new position contribution groups method is not only much more accurate but also has the advantages of simplicity and stability.

Changes of Petroleum Acid Distribution Characterized by FT-ICR MS in Heavy Acidic Crude Oil after True Boiling Point Distillation

The molecular transformations of carboxylic acids in heavy acidic SL crude before and after true boiling point distillation were examined by ultra-high resolution negative-ion electrospray ionization(ESI) Fourier transform ion cyclotron resonance mass spectrometry(FT-ICR MS). The acid class(heteroatom number), type(z numbers) and carbon number distributions were positively characterized. It was found out that the total acid number(TAN) of SL crude decreased after true boiling point distillation, and the abundance of O2 class in mass spectra was also found to be reduced from 67.6% to 34.5% in SL TBP mixed crude as measured by MS spectra, indicating to a potential carboxylic acid decomposition. However, it was interesting that the carboxylic acids type distribution in both oils was almost the same although their relative abundance in SL TBP mixed crude turned to be much lower, suggesting that various petroleum carboxylic acid types have the similar thermal decomposition reaction behavior. Furthermore, for each O2 type of acids in SL TBP mixed crude, the abundance of carboxylic acids with carbon number higher than 35 was reduced greatly, especially for those with carbon number higher than 60, the mass peaks of which were nearly totally removed, indicating that the large carboxylic acid molecules in heavy fractions decomposed more significantly because of longer heating time during the true boiling point distillation process. As a result, the reduction of TAN may be caused by the thermal decomposition of carboxylic acids especially those with high carbon number, suggesting that quick distillation or much lower pressure is required to avoid the thermal decomposition.

A New Experimental Rig of Testing Flow Boiling Heat Transfer of Refrigerantand Lubricant Mixture

This paper proposed a new experimental rig of testing flow boiling heat transfer of refrigerant and lubricant oil mixture. The quantity of oil in the test section can be controlled and regulated conveniently and accurately by connecting separate lubricant oil circuit with test section in parallel. It was built up by retrofitting a multiple air-conditioner and installing three oil-separators in serials at the compressor outlet. And so the lubricant oil in the discharged refrigerant gas of compressor can be removed completely.The refrigerant flow rate through test section can be bypassed by the by-path circuit of indoor unit.This experimental rig has advantages such as on-line and continuous oil injection, short time of obtaining stability, flexible operation, simple control, which lead to high efficiency in the research of flow boiling heat transfer of refrigerant and lubricant oil mixture.

Mechanism of Calcium Carbonate Scale Deposition under Subcooled Flow Boiling Conditions

Fouling of heat transfer surfaces during subcooled flow boiling is a frequent engineering problem in process industries. It has been generally observed that the deposits in such industrial systems consist mainly of calcium carbonate （CaCO3）, which has inverse solubility characteristics. This investigation focused on the mechanism to control deposition and the morphology of crystalline deposits. A series of experiments were carried out at different surface and bulk temperatures, fluid velocities and salt ion concentrations. It is shown that the deposition rate is controlled by different mechanism in the range of experimental parameters, depending on salt ion concentration. At higher ion concentration, the fouling rate increases linearly with surface temperature and the effect of flow velocity on deposition rate is quite strong, suggesting that mass diffusion controls the fouling process. On the contrary, at lower ion concentration, the fouling rate increases exponentially with surface temperature and is independent of the velocity, illustrating that surface reaction controls the fouling process. By analysis of the morphology of scale, two types of crystal （calcite and aragonite） are formed. The lower the temperature and ion concentration, the longer the induction period and the higher the percentage of calcite nreciDitated.

Support vector regression modeling in recursive just-in-time learning framework for adaptive soft sensing of naphtha boiling point in crude distillation unit

Prediction of primary quality variables in real time with adaptation capability for varying process conditions is a critical task in process industries.This article focuses on the development of non-linear adaptive soft sensors for prediction of naphtha initial boiling point(IBP)and end boiling point(EBP)in crude distillation unit.In this work,adaptive inferential sensors with linear and non-linear local models are reported based on recursive just in time learning(JITL)approach.The different types of local models designed are locally weighted regression(LWR),multiple linear regression(MLR),partial least squares regression(PLS)and support vector regression(SVR).In addition to model development,the effect of relevant dataset size on model prediction accuracy and model computation time is also investigated.Results show that the JITL model based on support vector regression with iterative single data algorithm optimization(ISDA)local model(JITL-SVR:ISDA)yielded best prediction accuracy in reasonable computation time.