Simultaneously removal of P and B from Si by Sr and Zr co-addition during Al–Si low-temperature solvent refining

To remove the key impurity elements,P and B,from primary Si simultaneously,Sr and Zr co-addition to Al-Si alloy systems during solvent refining has been investigated.Sr reacts with Al,Si,and P in the melt to form a P-containing Al_(2)Si_(2)Sr phase and Zr reacts with B to form a ZrB_(2) phase.In the Al-Si-Sr-Zr system,high removal fractions of P and B in the primary Si,with 84.8%-98.4%and 90.7%-96.7%,respectively,are achieved at the same time,respectively.The best removal effect is obtained in the sample with the addition of Sr-32000+Zr-3000μg·kg^(-1),and the removal fractions of P and B in the purified Si reach 98.4%and 96.1%.Compared with the Sr/Zr single-addition,the removal effects of Sr and Zr co-addition on P and B do not show a significant downward trend,indicating that the nucleation and growth of the B/P-containing impurity phases are mutually independent.Finally,an evolution model is proposed to describe the nucleation and the growth stages of Sr/Zr-containing compound phases,which reveals the interaction between the impurity phases and the primary Si.

Influence of Lanthanum on Tribological Properties and Microstructure of Laser Clad B+Fe+Si Composite Coatings

The effects of rare earth ferrosilicon on the microstructure and anti-wear properties of laser-clad Fe-based alloy coating were investigated. The composition of Fe, B_4C and rare earth ferrosilicon powders with different contents of lanthanum were clad onto a 45~# carbon steel substrate. Microstructural features, chemical compositions, phase structure, hardness, friction and wear properties by scanning electron microscopy (SEM), X-ray photoelectron microscopy (XPS), hardness tester, block-on-ring friction and wear tester of the clad coating were determined. Experimental results show that the friction coefficient of the clad coating doped with rare earth ferrosilicon is reduced while the wear resistance of clad coating doped with rare earth ferrosilicon is enhanced. When the content of lanthanum increases to 1.92%, the clad coating shows the best anti-wear ability, and as the content of lanthanum exceeds 1.92%, the wear weight loss increases quickly. The rare earth ferrosilicon to be doped in the clad coatings helps to disperse the boride phase (Fe_2B, FeB, B_4C) particles and refine the grain of boride phase. The enhancement of clad coating′s wear resistance is due to the existence of dispersed boride phases.

The Minor Precipitation at the Final Stage of U720Li Solidification

The minor precipitations caused by B and Zr which are the normal constituents of U720 Li alloy have been studied by analyzing the solidification process and the composition evolution. The present study aims to supply the elementary information about the existing form of B and Zr in the as-cast microstructure, which is helpful for the subsequent processing, such as homogenization treatment. The M_3B_2 and Ni_5Zr phases were observed in the U720 Li alloy in as-cast state, which were usually accompanying with each other together with g-Ni_3 Ti phase at the edge of eutectic（γ＋γ＇）. Combining the DTA analysis and heating and quenching tests, the solidification sequence was determined to be the following： c matrix, eutectic（γ＋γ＇）, g-Ni_3Ti, M_3B_2 and Ni_5Zr. The in situ composition analysis by EDS and EPMA revealed that the precipitation and microstructure were governed by the composition evolution in the liquids. The solidification of c matrix increased the Ti concentration in the residual liquids and resulted in the eutectic（γ＋γ＇） formation; the（γ＋γ＇） formation increased the Ti/Al radio in the liquids and the g-Ni_3Ti was formed in front of the eutectic（γ＋γ＇）; the g-Ni_3Ti precipitation consumed up Al and Ti and increased the concentration of B, Mo and Cr, and M_3B_2 boride is formed;the previous precipitation of the phases consumed up most of the elements other than Ni and Zr, and Ni_5Zr is formed finally. The melting points are in the ranges of 1130–1140 °C for Ni_5Zr phase, 1180–1190 °C for M_3B_2 boride and1190–1200 °C for g-Ni_3Ti phase.