Highly conductive boron-doped hydrogenated mieroerystalline silicon （μc-Si：H） films are prepared by very high frequency plasma enhanced chemical vapour deposition （VHF PECVD） at the substrate temperatures （Ts）...Highly conductive boron-doped hydrogenated mieroerystalline silicon （μc-Si：H） films are prepared by very high frequency plasma enhanced chemical vapour deposition （VHF PECVD） at the substrate temperatures （Ts） ranging from 90℃ to 270℃. The effects of Ts on the growth and properties of the films are investigated. Results indicate that the growth rate, the electrical （dark conductivity, carrier concentration and Hall mobility） and structural （crystallinity and grain size） properties are all strongly dependent on Ts. As Ts increases, it is observed that 1） the growth rate initially increases and then arrives at a maximum value of 13.3 nm/min at Ts=210℃, 2） the crystalline volume fraction （Xc） and the grain size increase initially, then reach their maximum values at TS=140℃, and finally decrease, 3） the dark conductivity （σd）, carrier concentration and Hall mobility have a similar dependence on Ts and arrive at their maximum values at Ts-190℃. In addition, it is also observed that at a lower substrate temperature Ts, a higher dopant concentration is required in order to obtain a maximum σd.展开更多
Thin transparent oxide conducting films(TCOFs)of titanium and gallium substituted zinc oxide(TGZO)were fabricated via radio frequency(RF)magnetron sputtering technique.The effects of RF power on electrical,linear and ...Thin transparent oxide conducting films(TCOFs)of titanium and gallium substituted zinc oxide(TGZO)were fabricated via radio frequency(RF)magnetron sputtering technique.The effects of RF power on electrical,linear and nonlinear optical characteristics were investigated by Hall tester,Ultraviolet(UV)-visible spectrophotometer and optical characterization method.The results indicate that RF power significantly influences the electrical and optical properties of the deposited films.As RF power raises,the resistivity and Urbach energy fall initially and then rise,while the figure of merit,mean visible transmittance and optical bandgap show the reverse variation trend.At RF power of 190 W,the TGZO sample exhibits the highest electro-optical properties,with the maximum figure of merit(1.14×10^(4)Ω^(-1)∙cm^(-1)),mean visible transmittance(86.9%)and optical bandgap(3.50 eV),the minimum resistivity(6.26×10^(-4)Ω∙cm)and Urbach energy(174.23 meV).In addition,the optical constants of the deposited films were determined by the optical spectrum fitting method,and the RF power dependence of nonlinear optical properties was studied.It is observed that all the thin films exhibit normal dispersion characteristics in the visible region,and the nonlinear optical parameters are greatly affected by the RF power in the ultraviolet region.展开更多
Using diborane as doping gas, p-doped μc-Si：H layers are deposited by using the plasma enhanced chemical vapour deposition （PECVD） technology. The effects of deposition pressure and plasma power on the growth and ...Using diborane as doping gas, p-doped μc-Si：H layers are deposited by using the plasma enhanced chemical vapour deposition （PECVD） technology. The effects of deposition pressure and plasma power on the growth and the properties of μc-Si：H layers are investigated. The results show that the deposition rate, the electrical and the structural properties are all strongly dependent on deposition pressure and plasma power. Boron-doped μc-Si：H films with a dark conductivity as high as 1.42 Ω^-1·cm^-1 and a crystallinity of above 50% are obtained. With this p-layer, μc-Si：H solar cells are fabricated. In addition, the mechanism for the effects of deposition pressure and plasma power on the growth and the properties of boron-doped μc-Si：H layers is discussed.展开更多
ZnO films with c -axis parallel to the substrate are reported.ZnO films are synthesized by solid-source chemical vapor deposition,a novel CVD technique,using zinc acetate dihydrate (solid) as the source material.The p...ZnO films with c -axis parallel to the substrate are reported.ZnO films are synthesized by solid-source chemical vapor deposition,a novel CVD technique,using zinc acetate dihydrate (solid) as the source material.The properties are characterized by X-ray diffraction,atomic force microscopy and transmission spectra.The parallel oriented ZnO films with mixed orientation for (100) and (110) planes are achieved on glass at the substrate temperature of 200℃ and the source temperature of 280℃,and a qualitative explanation is given for the forming of the mixed orientation.AFM images show that the surface is somewhat rough for the parallel oriented ZnO films.The transmission spectrum exhibits a high transmittance of about 85% in the visible region and shows an optical band gap about 3.25eV at room temperature.展开更多
Porous ZnO films are synthesized by inorganic chelating sol-gel method,which is a novel sol-gel technique using zinc nitrate as starting materials and citric acid as the chelating reagent.The crystal structure,surface...Porous ZnO films are synthesized by inorganic chelating sol-gel method,which is a novel sol-gel technique using zinc nitrate as starting materials and citric acid as the chelating reagent.The crystal structure,surface morphology,porous and optical properties of the deposited films are investigated.X-ray diffraction pattern analysis shows that crystal structure of the ZnO films is hexagonal wurtzite.Scanning electron microscopy (SEM) shows that the ZnO film is porous.The curve of pore size distribution has two peak values at about 2.02nm and 4.97nm and BET surface area of the ZnO film is 27.57m2/g.In addition,the transmittance spectrum gives a high transmittance of 85% in the visible region and optical bandgap of the ZnO film (fired at 500℃) is 3.25eV.展开更多
The growth characteristics during metalorganic chemical vapor deposition and optical properties of ZnO films on sapphire （Al2O3） （0001） and （1120） substrates are studied. For the former,the effects of two import...The growth characteristics during metalorganic chemical vapor deposition and optical properties of ZnO films on sapphire （Al2O3） （0001） and （1120） substrates are studied. For the former,the effects of two important growth parameters,i, e. temperature and pressure, are investigated in detail. Due to the large lattice mismatch between the film and the substrate, ZnO nanocrystals are usually obtained. The growth behavior at the film-substrate interface is found to be strongly dependent on the growth temperature,while the growth pressure determines the shape of the nanostructures as they grow. It is difficult to obtain ZnO films that have good quality and a smooth surface simultaneously. Due to the smaller lattice mismatch,the critical thickness of ZnO on the Al2O3 （1120） surface is found to be much larger than that on the Al2O3 （0001） surface. ZnO/MgZnO quantum wells with graded well thicknesses are grown on the Al2O3 （1120） surfaces,and their optical properties are studied. The built-in electric field in the well layer, generated by the piezoelectric effect, is estimated to be 3 × 10^5 V/cm. It is found that growth at low temperatures and low pressures may facilitate the incorporation of acceptor impurities in ZnO.展开更多
Al-doped zinc oxide（AZO） films were deposited on glass substrates by mid-frequency magnetron sputtering. The effects of substrate rotation speed and target-substrate distance on the electrical, optical properties an...Al-doped zinc oxide（AZO） films were deposited on glass substrates by mid-frequency magnetron sputtering. The effects of substrate rotation speed and target-substrate distance on the electrical, optical properties and microstructure and crystal structures of the resulting films were investigated by scanning electron microscopy（SEM）, atomic force microscopy（AFM）, X-ray diffraction（XRD）, spectrophotometer and Hall-effect measurement system, respectively. XRD results show that all AZO films exhibit a strong preferred c-axis orientation. However, the crystallinity of films decreases with the increase of substrate rotation speed, accompanying with the unbalanced grains grows. For the films prepared at different target-substrate distances, the uniform microstructure and morphology are observed. The highest carrier concentration of 5.9×1020 cm-3 and Hall mobility of 13.1 cm^2/（V·s） are obtained at substrate rotation speed of 0 and target-substrate distance of 7 cm. The results indicate that the structure and performances of the AZO films are strongly affected by substrate rotation speed.展开更多
Boron-doped zinc oxide transparent （BZO） films were prepared by sol-gel method. The effect of pyrolysis temperature on the crystallization behavior and properties was systematically investigated. XRD patterns reveal...Boron-doped zinc oxide transparent （BZO） films were prepared by sol-gel method. The effect of pyrolysis temperature on the crystallization behavior and properties was systematically investigated. XRD patterns revealed that the BZO films had wurtzite structure with a preferential growth orientation along the c-axis. With the increase of pyrolysis temperature, the particle size and surface roughness of the BZO films increased, suggesting that pyrolysis temperature is the critical factor for determining the crystallization behavior of the BZO films. Moreover, the carrier concentration and the carrier mobility increased with increasing the pyrolysis temperature, and the mean transmittance for every film is over 90% in the visible range.展开更多
The first-principles density functional calculation is used to investigate the electronic structures and magnetic properties of Mn-doped and N-co-doped ZnO nanofilms.The band structure calculation shows that the band ...The first-principles density functional calculation is used to investigate the electronic structures and magnetic properties of Mn-doped and N-co-doped ZnO nanofilms.The band structure calculation shows that the band gaps of ZnO films with 2,4,and 6 layers are larger than the band gap of the bulk with wurtzite structure and decrease with the increase of film thickness.However,the four-layer ZnO nanofilms exhibit ferromagnetic phases for Mn concentrations less than 24% and 12% for Mn-doping performed in the whole layers and two layers of the film respectively,while they exhibit spin glass phases for higher Mn concentrations.It is also found,on the one hand,that the spin glass phase turns into the ferromagnetic one,with the substitution of nitrogen atoms for oxygen atoms,for nitrogen concentrations higher than 16% and 5% for Mn-doping performed in the whole layers and two layers of the film respectively.On the other hand,the spin-glass state is more stable for ZnO bulk containing 5% of Mn impurities,while the ferromagnetic phase is stable by introducing the p-type carriers into the bulk system.Moreover,it is shown that using the effective field theory for ferromagnetic system,the Curie temperature is close to the room temperature for the undamped Ruderman-Kittel-Kasuya-Yoshida（RKKY） interaction.展开更多
Graphite oxide （GO） is an important material of wide applications. Owing to its good mechanical property, the GO sheet is always expected to be stable and remains flat on various substrates. Here we demonstrate for ...Graphite oxide （GO） is an important material of wide applications. Owing to its good mechanical property, the GO sheet is always expected to be stable and remains flat on various substrates. Here we demonstrate for the first time an unexpected behavior of the GO sheet on oxygen deficient ZnO film, namely the spontaneous cracking of the entire GO sheet into many small pieces. This unusual behavior has been carefully investigated by a series of control experiments and SEM, XPS and PL measurements. It is anticipated that the oxygen vacancies in the oxygen deficient ZnO film can annihilate epoxy groups of the GO sheet, resulting in the unzipping of the aligned epoxy groups on GO sheet. A prototype of the white light detector made from the cracked GO sheet is fabricated and the device demonstrates high stability and good reproducibility.展开更多
ZnO thin films were grown on GaAs （001） substrates by metal-organic chemical vapor deposition （MOCVD） at low temperatures ranging from 100 to 400℃. DEZn and 1-12 O were used as the zinc precursor and oxygen precu...ZnO thin films were grown on GaAs （001） substrates by metal-organic chemical vapor deposition （MOCVD） at low temperatures ranging from 100 to 400℃. DEZn and 1-12 O were used as the zinc precursor and oxygen precursor, respectively. The effects of the growth temperatures on the growth characteristics and optical properties of ZnO films were investigated. The X-ray diffraction measurement （XRD） results indicated that all the thin films were grown with highly c- axis orientation. The surface morphologies and crystal properties of the films were critically dependent on the growth temperatures. Although there was no evidence of epitaxial growth, the scanning electron microscopy （SEM） image of ZnO film grown at 400℃ revealed the presence of ZnO microcrystallines with closed packed hexagon structure. The photoluminescence spectrum at room temperature showed only bright band-edge （3. 33eV） emissions with little or no deep-level e- mission related to defects.展开更多
This paper reports that ion implantation to a dose of 1 ×10^17 ions/cm^2 was performed on c-axis-orientated ZnO thin films deposited on （0001） sapphire substrates by the sol-gel technique. After ion implantatio...This paper reports that ion implantation to a dose of 1 ×10^17 ions/cm^2 was performed on c-axis-orientated ZnO thin films deposited on （0001） sapphire substrates by the sol-gel technique. After ion implantation, the as-implanted ZnO films were annealed in argon ambient at different temperatures from 600 - 900 ℃. The effects of ion implantation and post-implantation annealing on the structural and optical properties of the ZnO films were investigated by x-ray diffraction （XRD）, photoluminescence （PL）. It was found that the intensities of （002） peak and near band edge （NBE） exitonic ultraviolet emission increased with increasing annealing temperature from 600- 900 ℃. The defect related deep level emission （DLE） firstly increased with increasing annealing temperature from 600 - 750 ℃, and then decreased quickly with increasing annealing temperature. The recovery of the intensities of NBE and DLE occurs at ～850℃ and ～750℃ respectively. The relative PL intensity ratio of NBE to DLE showed that the quality of ZnO films increased continuously with increasing annealing temperature from 600 - 900 ℃.展开更多
In this study,the electrochemical oxidation of reactive brilliant orange X-GN dye with a boron-doped diamond(BDD)anode was investigated.The BDD electrodes were deposited on the niobium(Nb)substrates by the hot filamen...In this study,the electrochemical oxidation of reactive brilliant orange X-GN dye with a boron-doped diamond(BDD)anode was investigated.The BDD electrodes were deposited on the niobium(Nb)substrates by the hot filament chemical vapor deposition method.The effects of processing parameters,such as film thickness,current density,supporting electrolyte concentration,initial solution pH,solution temperature,and initial dye concentration,were evaluated following the variation in the degradation efficiency.The microstructure and the electrochemical property of BDD were characterized by scanning electron microscopy,Raman spectroscopy,and electrochemical workstation;and the degradation of X-GN was estimated using UV-Vis spectrophotometry.Further,the results indicated that the film thickness of BDD had a significant impact on the electrolysis of X-GN.After 3 h of treatment,100%color and 63.2%total organic carbon removal was achieved under optimized experimental conditions:current density of 100 mA/cm2,supporting electrolyte concentration of 0.05 mol/L,initial solution pH 3.08,and solution temperature of 60°C.展开更多
文摘Highly conductive boron-doped hydrogenated mieroerystalline silicon （μc-Si：H） films are prepared by very high frequency plasma enhanced chemical vapour deposition （VHF PECVD） at the substrate temperatures （Ts） ranging from 90℃ to 270℃. The effects of Ts on the growth and properties of the films are investigated. Results indicate that the growth rate, the electrical （dark conductivity, carrier concentration and Hall mobility） and structural （crystallinity and grain size） properties are all strongly dependent on Ts. As Ts increases, it is observed that 1） the growth rate initially increases and then arrives at a maximum value of 13.3 nm/min at Ts=210℃, 2） the crystalline volume fraction （Xc） and the grain size increase initially, then reach their maximum values at TS=140℃, and finally decrease, 3） the dark conductivity （σd）, carrier concentration and Hall mobility have a similar dependence on Ts and arrive at their maximum values at Ts-190℃. In addition, it is also observed that at a lower substrate temperature Ts, a higher dopant concentration is required in order to obtain a maximum σd.
文摘Thin transparent oxide conducting films(TCOFs)of titanium and gallium substituted zinc oxide(TGZO)were fabricated via radio frequency(RF)magnetron sputtering technique.The effects of RF power on electrical,linear and nonlinear optical characteristics were investigated by Hall tester,Ultraviolet(UV)-visible spectrophotometer and optical characterization method.The results indicate that RF power significantly influences the electrical and optical properties of the deposited films.As RF power raises,the resistivity and Urbach energy fall initially and then rise,while the figure of merit,mean visible transmittance and optical bandgap show the reverse variation trend.At RF power of 190 W,the TGZO sample exhibits the highest electro-optical properties,with the maximum figure of merit(1.14×10^(4)Ω^(-1)∙cm^(-1)),mean visible transmittance(86.9%)and optical bandgap(3.50 eV),the minimum resistivity(6.26×10^(-4)Ω∙cm)and Urbach energy(174.23 meV).In addition,the optical constants of the deposited films were determined by the optical spectrum fitting method,and the RF power dependence of nonlinear optical properties was studied.It is observed that all the thin films exhibit normal dispersion characteristics in the visible region,and the nonlinear optical parameters are greatly affected by the RF power in the ultraviolet region.
基金Project supported by the State Key Development Program for Basic Research of China (Grant No 2006CB202601)Basic Research Project of Henan province,China (Grant No 072300410140)
文摘Using diborane as doping gas, p-doped μc-Si：H layers are deposited by using the plasma enhanced chemical vapour deposition （PECVD） technology. The effects of deposition pressure and plasma power on the growth and the properties of μc-Si：H layers are investigated. The results show that the deposition rate, the electrical and the structural properties are all strongly dependent on deposition pressure and plasma power. Boron-doped μc-Si：H films with a dark conductivity as high as 1.42 Ω^-1·cm^-1 and a crystallinity of above 50% are obtained. With this p-layer, μc-Si：H solar cells are fabricated. In addition, the mechanism for the effects of deposition pressure and plasma power on the growth and the properties of boron-doped μc-Si：H layers is discussed.
文摘ZnO films with c -axis parallel to the substrate are reported.ZnO films are synthesized by solid-source chemical vapor deposition,a novel CVD technique,using zinc acetate dihydrate (solid) as the source material.The properties are characterized by X-ray diffraction,atomic force microscopy and transmission spectra.The parallel oriented ZnO films with mixed orientation for (100) and (110) planes are achieved on glass at the substrate temperature of 200℃ and the source temperature of 280℃,and a qualitative explanation is given for the forming of the mixed orientation.AFM images show that the surface is somewhat rough for the parallel oriented ZnO films.The transmission spectrum exhibits a high transmittance of about 85% in the visible region and shows an optical band gap about 3.25eV at room temperature.
文摘Porous ZnO films are synthesized by inorganic chelating sol-gel method,which is a novel sol-gel technique using zinc nitrate as starting materials and citric acid as the chelating reagent.The crystal structure,surface morphology,porous and optical properties of the deposited films are investigated.X-ray diffraction pattern analysis shows that crystal structure of the ZnO films is hexagonal wurtzite.Scanning electron microscopy (SEM) shows that the ZnO film is porous.The curve of pore size distribution has two peak values at about 2.02nm and 4.97nm and BET surface area of the ZnO film is 27.57m2/g.In addition,the transmittance spectrum gives a high transmittance of 85% in the visible region and optical bandgap of the ZnO film (fired at 500℃) is 3.25eV.
文摘The growth characteristics during metalorganic chemical vapor deposition and optical properties of ZnO films on sapphire （Al2O3） （0001） and （1120） substrates are studied. For the former,the effects of two important growth parameters,i, e. temperature and pressure, are investigated in detail. Due to the large lattice mismatch between the film and the substrate, ZnO nanocrystals are usually obtained. The growth behavior at the film-substrate interface is found to be strongly dependent on the growth temperature,while the growth pressure determines the shape of the nanostructures as they grow. It is difficult to obtain ZnO films that have good quality and a smooth surface simultaneously. Due to the smaller lattice mismatch,the critical thickness of ZnO on the Al2O3 （1120） surface is found to be much larger than that on the Al2O3 （0001） surface. ZnO/MgZnO quantum wells with graded well thicknesses are grown on the Al2O3 （1120） surfaces,and their optical properties are studied. The built-in electric field in the well layer, generated by the piezoelectric effect, is estimated to be 3 × 10^5 V/cm. It is found that growth at low temperatures and low pressures may facilitate the incorporation of acceptor impurities in ZnO.
基金Project(51302044)supported by the National Natural Science Foundation of ChinaProject(2012M521596)supported by the Chinese Postdoctoral Science FoundationProject(KLB11003)supported by the Key Laboratory of Clean Energy Materials of Guangdong Higher Education Institute,China
文摘Al-doped zinc oxide（AZO） films were deposited on glass substrates by mid-frequency magnetron sputtering. The effects of substrate rotation speed and target-substrate distance on the electrical, optical properties and microstructure and crystal structures of the resulting films were investigated by scanning electron microscopy（SEM）, atomic force microscopy（AFM）, X-ray diffraction（XRD）, spectrophotometer and Hall-effect measurement system, respectively. XRD results show that all AZO films exhibit a strong preferred c-axis orientation. However, the crystallinity of films decreases with the increase of substrate rotation speed, accompanying with the unbalanced grains grows. For the films prepared at different target-substrate distances, the uniform microstructure and morphology are observed. The highest carrier concentration of 5.9×1020 cm-3 and Hall mobility of 13.1 cm^2/（V·s） are obtained at substrate rotation speed of 0 and target-substrate distance of 7 cm. The results indicate that the structure and performances of the AZO films are strongly affected by substrate rotation speed.
文摘Boron-doped zinc oxide transparent （BZO） films were prepared by sol-gel method. The effect of pyrolysis temperature on the crystallization behavior and properties was systematically investigated. XRD patterns revealed that the BZO films had wurtzite structure with a preferential growth orientation along the c-axis. With the increase of pyrolysis temperature, the particle size and surface roughness of the BZO films increased, suggesting that pyrolysis temperature is the critical factor for determining the crystallization behavior of the BZO films. Moreover, the carrier concentration and the carrier mobility increased with increasing the pyrolysis temperature, and the mean transmittance for every film is over 90% in the visible range.
文摘The first-principles density functional calculation is used to investigate the electronic structures and magnetic properties of Mn-doped and N-co-doped ZnO nanofilms.The band structure calculation shows that the band gaps of ZnO films with 2,4,and 6 layers are larger than the band gap of the bulk with wurtzite structure and decrease with the increase of film thickness.However,the four-layer ZnO nanofilms exhibit ferromagnetic phases for Mn concentrations less than 24% and 12% for Mn-doping performed in the whole layers and two layers of the film respectively,while they exhibit spin glass phases for higher Mn concentrations.It is also found,on the one hand,that the spin glass phase turns into the ferromagnetic one,with the substitution of nitrogen atoms for oxygen atoms,for nitrogen concentrations higher than 16% and 5% for Mn-doping performed in the whole layers and two layers of the film respectively.On the other hand,the spin-glass state is more stable for ZnO bulk containing 5% of Mn impurities,while the ferromagnetic phase is stable by introducing the p-type carriers into the bulk system.Moreover,it is shown that using the effective field theory for ferromagnetic system,the Curie temperature is close to the room temperature for the undamped Ruderman-Kittel-Kasuya-Yoshida（RKKY） interaction.
基金ACKNOWLEDGMENTS This work was supported by the Ministry of Science and Technology of China （No.2011CB921403）, the Chinese Academy of Science （No.XDB01020000）, and the National Natural Science Foundation of China.
文摘Graphite oxide （GO） is an important material of wide applications. Owing to its good mechanical property, the GO sheet is always expected to be stable and remains flat on various substrates. Here we demonstrate for the first time an unexpected behavior of the GO sheet on oxygen deficient ZnO film, namely the spontaneous cracking of the entire GO sheet into many small pieces. This unusual behavior has been carefully investigated by a series of control experiments and SEM, XPS and PL measurements. It is anticipated that the oxygen vacancies in the oxygen deficient ZnO film can annihilate epoxy groups of the GO sheet, resulting in the unzipping of the aligned epoxy groups on GO sheet. A prototype of the white light detector made from the cracked GO sheet is fabricated and the device demonstrates high stability and good reproducibility.
文摘ZnO thin films were grown on GaAs （001） substrates by metal-organic chemical vapor deposition （MOCVD） at low temperatures ranging from 100 to 400℃. DEZn and 1-12 O were used as the zinc precursor and oxygen precursor, respectively. The effects of the growth temperatures on the growth characteristics and optical properties of ZnO films were investigated. The X-ray diffraction measurement （XRD） results indicated that all the thin films were grown with highly c- axis orientation. The surface morphologies and crystal properties of the films were critically dependent on the growth temperatures. Although there was no evidence of epitaxial growth, the scanning electron microscopy （SEM） image of ZnO film grown at 400℃ revealed the presence of ZnO microcrystallines with closed packed hexagon structure. The photoluminescence spectrum at room temperature showed only bright band-edge （3. 33eV） emissions with little or no deep-level e- mission related to defects.
文摘This paper reports that ion implantation to a dose of 1 ×10^17 ions/cm^2 was performed on c-axis-orientated ZnO thin films deposited on （0001） sapphire substrates by the sol-gel technique. After ion implantation, the as-implanted ZnO films were annealed in argon ambient at different temperatures from 600 - 900 ℃. The effects of ion implantation and post-implantation annealing on the structural and optical properties of the ZnO films were investigated by x-ray diffraction （XRD）, photoluminescence （PL）. It was found that the intensities of （002） peak and near band edge （NBE） exitonic ultraviolet emission increased with increasing annealing temperature from 600- 900 ℃. The defect related deep level emission （DLE） firstly increased with increasing annealing temperature from 600 - 750 ℃, and then decreased quickly with increasing annealing temperature. The recovery of the intensities of NBE and DLE occurs at ～850℃ and ～750℃ respectively. The relative PL intensity ratio of NBE to DLE showed that the quality of ZnO films increased continuously with increasing annealing temperature from 600 - 900 ℃.
基金Project(2016YEB0301402) supported by the National Key Research and Development Program of ChinaProject(51601226) supported by the National Natural Science Foundation of China+1 种基金Project supported by the Open-End Fund for the Valuable and Precision Instruments of Central South University,ChinaProject supported by State Key Laboratory of Powder Metallurgy,China
文摘In this study,the electrochemical oxidation of reactive brilliant orange X-GN dye with a boron-doped diamond(BDD)anode was investigated.The BDD electrodes were deposited on the niobium(Nb)substrates by the hot filament chemical vapor deposition method.The effects of processing parameters,such as film thickness,current density,supporting electrolyte concentration,initial solution pH,solution temperature,and initial dye concentration,were evaluated following the variation in the degradation efficiency.The microstructure and the electrochemical property of BDD were characterized by scanning electron microscopy,Raman spectroscopy,and electrochemical workstation;and the degradation of X-GN was estimated using UV-Vis spectrophotometry.Further,the results indicated that the film thickness of BDD had a significant impact on the electrolysis of X-GN.After 3 h of treatment,100%color and 63.2%total organic carbon removal was achieved under optimized experimental conditions:current density of 100 mA/cm2,supporting electrolyte concentration of 0.05 mol/L,initial solution pH 3.08,and solution temperature of 60°C.
