This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by...This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by means of a fluid–structure interaction(FSI)method by which the descaling effect produced by rolling coils with different section sizes is examined.Assuming a flat fan-shaped nozzle at the entrance of the R1R2 roughing mill,the outflow field characteristics and the velocity distribution curve on the strike line(at a target distance of 30–120 mm)are determined.It is found that the velocity in the center region of the water jet with different target distances is higher than that in the boundary region.As the target distance increases,the velocity of the water jet in the central region decreases.Through comparison with experimental results,it is shown that the simulation model can accurately predict the impact position of the high-pressure water on the impact plate,thereby providing a computational scheme that can be used to optimize the nozzle space layout and improve the slabs’descent effect for different rolling specifications.展开更多
Effective monitoring of the structural health of combined coal-rock under complex geological conditions by pressure stimulated currents(PSCs)has great potential for the understanding of dynamic disasters in undergroun...Effective monitoring of the structural health of combined coal-rock under complex geological conditions by pressure stimulated currents(PSCs)has great potential for the understanding of dynamic disasters in underground engineering.To reveal the effect of this way,the uniaxial compression experiments with PSC monitoring were conducted on three types of coal-rock combination samples with different strength combinations.The mechanism explanation of PSCs are investigated by resistivity test,atomic force microscopy(AFM)and computed tomography(CT)methods,and a PSC flow model based on progressive failure process is proposed.The influence of strength combinations on PSCs in the progressive failure process are emphasized.The results show the PSC responses between rock part,coal part and the two components are different,which are affected by multi-scale fracture characteristics and electrical properties.As the rock strength decreases,the progressive failure process changes obviously with the influence range of interface constraint effect decreasing,resulting in the different responses of PSC strength and direction in different parts to fracture behaviors.The PSC flow model is initially validated by the relationship between the accumulated charges of different parts.The results are expected to provide a new reference and method for mining design and roadway quality assessment.展开更多
Karst sinkholes with natural negative landform provide favorable conditions for the pumped storage reservoir construction for less excavation work.However,the construction of the reservoir would plug the natural karst...Karst sinkholes with natural negative landform provide favorable conditions for the pumped storage reservoir construction for less excavation work.However,the construction of the reservoir would plug the natural karst channels for water and air,which would cause remarkable air pressure in karst channels when the groundwater level fluctuates.A large laboratory simulation test was carried out to study the air pressure variation of a reservoir built on the karst sinkhole.The air pressure in the karst channel and inside the model was monitored during the groundwater rising and falling process.Result showed that the variation of air pressure in the karst channel and the surrounding rock exhibited a high degree of similarity.The air pressure increased rapidly at the initial stage of water level rising,followed by a slight decrease,then the air pressure increased sharply when the water level approached the top of the karst cave.The initial peak of air pressure and the final peak of air pressure were defined,and both air pressure peaks were linearly increasing with the water level rising rate.The negative air pressure was also analyzed during the drainage process,which was linearly correlated with the water level falling rate.The causes of air pressure variation in karst channels of a pumped storage reservoir built on the karst sinkhole were discussed.The initial rapid increase,then slight decrease and final sudden increase of air pressure were controlled by the combined effects of air compression in karst channel and air seepage into the surrounding rock.For the drainage process,the instant negative air pressure and gradual recovering of air pressure were controlled by the combined effects of negative air pressure induced by water level falling and air supply from surrounding rock.This work could provide valuable reference for the reservoir construction in karst area.展开更多
This paper aims to propose correlations to predict pressure gradient,friction factor and fluid phase hold-up in liquid-liquid horizontal pipe flow.To develop the correlations,experiments are conducted using high visco...This paper aims to propose correlations to predict pressure gradient,friction factor and fluid phase hold-up in liquid-liquid horizontal pipe flow.To develop the correlations,experiments are conducted using high viscous oils(202 and 630 mPa⋅s)in a steel pipe of length 11.25 m and length-to-diameter ratio of 708.In addition,the experimental data from the literature comprising wide range of flow and fluid properties is analyzed.For the analysis,the liquid-liquid pipe flow data is categorized into two as:stratified and dispersed.The existing friction factor correlations are modified to incorporate the effects of viscosity of the oil phase,interfacial curvature(contact/wetting angle-in lieu of material of the pipe)and fluid phase fraction.In the two-fluid model of stratified flow,the wall stress and interfacial stress correlations are substituted with superficial velocities of fluids and superficial Reynolds numbers of fluid phases replacing fluid phase velocities and fluid Reynolds numbers.Similarly,for dispersed flow,an effective Reynolds number is described as the sum of superficial Reynolds number of oil and water phases.Substituting the generally employed mean or mixture Reynolds number with the effective Reynolds number into the existing single-phase turbulent flow friction factor correlation,an effective friction factor for oil-water flow is proposed.Employing the proposed correlations,the pressure gradient across the oil-water flow and hold-up volume fraction are predicted with significant reduction in error compared with that of conventionally employed correlations.The average error and standard deviation values of−7.06%,20.72%and 0.31%,18.79%are found for stratified flow and dispersed flow respectively.展开更多
A new numerical model for low-permeability reservoirs is developed.The model incorporates the nonlinear characteristics of oil-water two-phase flows while taking into account the initiation pressure gradient.Related n...A new numerical model for low-permeability reservoirs is developed.The model incorporates the nonlinear characteristics of oil-water two-phase flows while taking into account the initiation pressure gradient.Related numerical solutions are obtained using a finite difference method.The correctness of the method is demonstrated using a two-dimensional inhomogeneous low permeability example.Then,the differences in the cumulative oil and water production are investigated for different starting water saturations.It is shown that when the initial water saturation grows,the water content of the block continues to rise and the cumulative oil production gradually decreases.展开更多
The use of open-type check dams in mountainous areas has become common practice in order to mitigate the effects of debris flow and extend the service life of engineering structures.The beam dam,a common debris flow c...The use of open-type check dams in mountainous areas has become common practice in order to mitigate the effects of debris flow and extend the service life of engineering structures.The beam dam,a common debris flow control system,has received less attention in research on the impact process of debris flow and check dams compared to solid check dams.Additionally,the estimation of impact pressure in debris flow primarily considers debris flow characteristics,without taking into account the influence of geometric characteristics of the transmission structure.To better understand the impact process of debris flow on beam dams,a series of small-scale debris flow impact tests were conducted in a model flume.Key parameters,including velocity,depth,and impact pressure,were measured.The results show that the maximum impact pressure of debris flow is affected by both the characteristics of the debris flow and the relative opening size of the beam dam.Due to flow and edge occlusion in the middle of the beam dam,the discharge of debris flow is enhanced,resulting in a longer impact process and higher maximum impact pressure.Based on these findings,a calculation model of the maximum impact pressure of debris flow at the midpoint of the middle beam is proposed,which can be used to estimate the impact of debris flow on the discharge part of the beam dam.展开更多
Due to the inherent working mode of rotating detonation engine(RDE),the detonation flow field has the characteristics of pressure oscillation and axial kinetic energy loss,which makes it difficult to design nozzle and...Due to the inherent working mode of rotating detonation engine(RDE),the detonation flow field has the characteristics of pressure oscillation and axial kinetic energy loss,which makes it difficult to design nozzle and improve propulsion performance.Therefore,in order to improve the characteristics of detonation flow field,the three-dimensional numerical simulation of annular chamber and hollow chamber is carried out with premixed hydrogen/air as fuel in this paper,and then tries to combine the two chambers to weaken the oscillation characteristics of detonation flow field through the interaction of detonation flow field,which is a new method to regulate the detonation flow field.The results show that there are four states of velocity vectors at the outlet of annular chamber and hollow chamber,which makes RDE be affected by rolling moment and results in the loss of axial kinetic energy.In the external flow field of combined chamber,the phenomenon of cyclic reflection of expansion wave and compression wave on the free boundary is observed,which results in Mach disk structure.Moreover,the pressure monitoring points are set at the external flow field.The pressure signal shows that the high-frequency pressure oscillation at the external flow field of the combined chamber has been greatly weakened.Compared to the annular chamber,the relative standard deviation(RSD) has been reduced from 14.6% to5.6%.The results thus demonstrate that this method is feasible to adjust the pressure oscillation characteristics of the detonation flow field,and is of great significance to promote the potential of RDE and nozzle design.展开更多
The pressure-sensitive effect on the pore structure of sandstone was investigated using X-ray computed micro-tomography and QEMSCAN quantitative mineral analysis. In a physical simulation study, we extracted the pore ...The pressure-sensitive effect on the pore structure of sandstone was investigated using X-ray computed micro-tomography and QEMSCAN quantitative mineral analysis. In a physical simulation study, we extracted the pore network model from digital cores at different confining pressures and evaluated the effect of pressure sensitivity on the multiphase displacement process. In both the pore network model and QEMSCAN scanning, the pore structure was observed to be damaged under a high confining pressure. Due to their different scales, the pores and throats exhibited inhomogeneous changes; further, the throats exhibited a significant variation compared to that exhibited by the pores. Meanwhile, the heterogeneity of the pore structure under the two aforementioned activities was aggravated by the elastic-plastic deformation of the pore structure.The pressure-sensitive effect increased the proportion of mineral particles, such as quartz(the main component of the core skeleton), and reduced the proportion of clay minerals. The clay minerals were originally attached to the pore walls or interspersed in the pores; however, as the pressure increased, the clay minerals accumulated in the pores resulting in blockage of the pores. While simulating the multiphase displacement process, increasing the confining pressure was observed to severely restrict the flowability of oil and water. This study promises to improve the efficiency of reservoir development in terms of oil and gas exploitation.展开更多
A compact annular-radial-orifice flow magnetorheological(MR)valve was developed to investigate the effects of radial resistance gap on pressure drop.The fluid flow paths of this proposed MR valve consist of a single a...A compact annular-radial-orifice flow magnetorheological(MR)valve was developed to investigate the effects of radial resistance gap on pressure drop.The fluid flow paths of this proposed MR valve consist of a single annular flow channel,a single radial flow channel and an orifice flow channel through structure design.The finite element modelling and simulation analysis of the MR valve was carried out using ANSYS/Emag software to investigate the changes of the magnetic flux density and yield stress along the fluid flow paths under the four different radial resistance gaps.Moreover,the experimental tests were also conducted to evaluate the pressure drop,showing that the proposed MR valve has significantly improved its pressure drop at 0.5 mm width of the radial resistance gap when the annular resistance gap is fixed at 1 mm.展开更多
Impact force is a crucial factor to be considered in debris-resisting structure design. The impact of debris flow against a structural barrier depends not only on the flow dynamics but also on the barrier material. Ba...Impact force is a crucial factor to be considered in debris-resisting structure design. The impact of debris flow against a structural barrier depends not only on the flow dynamics but also on the barrier material. Based on the structural vibration equation and energy conservation law, a simple model for calculating debris-flow impact pressure is proposed, which includes the mechanical impedance of the material, debris-flow velocity and Froude number. Twenty-five impact tests have been conducted using different kinds of materials: steel, black granite, white granite, marble and polyvinyl chloride(PVC) board, and the ratio of the maximum impact time to the vibration period of the structure is determined for the model. It is found that the ratio's square root shows a linear relationship with the material solid Froude number. This indicates that the impedance of the structures plays an important role in the flow-barrier interaction. Moreover, the debrisflow impact force is found to decrease with the travel time of the elastic stress wave though the structures.展开更多
A cold-model vertical multi-tube circulating fluidized bed evaporator was designed and built to conduct a visualization study on the pressure drop of a liquid–solid two-phase flow and the corresponding particle distr...A cold-model vertical multi-tube circulating fluidized bed evaporator was designed and built to conduct a visualization study on the pressure drop of a liquid–solid two-phase flow and the corresponding particle distribution.Water and polyformaldehyde particle(POM)were used as the liquid and solid phases,respectively.The effects of operating parameters such as the amount of added particles,circulating flow rate,and particle size were systematically investigated.The results showed that the addition of the particles increased the pressure drop in the vertical tube bundle.The maximum pressure drop ratios were 18.65%,21.15%,18.00%,and 21.15%within the experimental range of the amount of added particles for POM1,POM2,POM3,and POM4,respectively.The pressure drop ratio basically decreased with the increase in the circulating flow rate but fluctuated with the increase in the amount of added particles and particle size.The difference in pressure drop ratio decreased with the increase in the circulating flow rate.As the amount of added particles increased,the difference in pressure drop ratio fluctuated at low circulating flow rate but basically decreased at high circulating flow rate.The pressure drop in the vertical tube bundle accounted for about 70%of the overall pressure drop in the up-flow heating chamber and was the main component of the overall pressure within the experimental range.Three-dimensional phase diagrams were established to display the variation ranges of the pressure drop and pressure drop ratio in the vertical tube bundle corresponding to the operating parameters.The research results can provide some reference for the application of the fluidized bed heat transfer technology in the industry.展开更多
In order to research start-up pressure wave propagation mechanism and determine pressure wave speed in gelled crude oil pipelines accurately,experiment of Large-scale flow loop was carried out.In the experiment,start-...In order to research start-up pressure wave propagation mechanism and determine pressure wave speed in gelled crude oil pipelines accurately,experiment of Large-scale flow loop was carried out.In the experiment,start-up pressure wave speeds under various operation conditions were measured,and effects of correlative factors on pressure wave were analyzed.The experimental and theoretical analysis shows that thermal shrinkage and structural properties of gelled crude oils are key factors influencing on start-up pressure wave propagation.The quantitative analysis for these effects can be done by using volume expansion coefficient and structural property parameter of gelled crude oil.A new calculation model of pressure wave speed was developed on the basis of Large-scale flow loop experiment and theoretical analysis.展开更多
The permeability of coal ahead of the working face obviously changes dues to changes in abutment pressure.The formation and evolution of gas flow channels within the abutment pressure area was studied by analyzing the...The permeability of coal ahead of the working face obviously changes dues to changes in abutment pressure.The formation and evolution of gas flow channels within the abutment pressure area was studied by analyzing the fracture extension mechanism and fracture development in different zones of the abutment pressure area.Fracture and damage mechanics theory is used to understand the observations.The following two techniques were used to understand the evolution of gas flow channels:field observation of the characteristic fractures at different positions relative to the working face and fluorescence micrographs of prepared coal samples.Bending tensile fractures develop along an approximately vertical direction that forms a microscopic network of channels in areas of stress concentration.The abutment pressure affects the local stress and,hence,the local gas conduction.The fractures induced by large deformation and plastic flow form macroscopically networked channels in the reduced stress area.Closer to the working face the gas flow channels evolve from microscopic to macroscopic and from isolated to network.Gas permeability continuously increases during this time.This is corroborated by field observations of the displacement of top coal and the gas flow from gas extraction drillings.展开更多
With ongoing development of oil exploration and techniques,there is a significant need for improved well control strategies and formation pressure prediction methods.In this paper,a gas-liquid transient drift flow mod...With ongoing development of oil exploration and techniques,there is a significant need for improved well control strategies and formation pressure prediction methods.In this paper,a gas-liquid transient drift flow model was established according to the gas-liquid two-phase flow characteristics during the gas kick.A Roe scheme was used for numerical calculation based on the finite volume method.The changes of bottom-hole pressure,casing pressure,the development law of cross-sectional gas holdup,and gas velocity,along with the vertical well depth,were analyzed through simulation examples.The time-series characteristics of mud pit gain were obtained by adjusting the formation parameter.The complex nonlinear mapping relationship between the formation parameters and the mud pit gain was established.The long short-term memory network(LSTM)of deep learning was used to obtain a formation pressure inversion when the blowout is out of control and the well cannot be shut-in.Experimental data from a well were used to verify the gas-liquid two-phase transient drift flow model based on the finite volume method,demonstrating that this method is reliable,with greatly improved prediction accuracy.This approach provides theoretical support for the early monitoring of gas kick during drilling,and for well-killing design and construction after uncontrolled blowout.展开更多
In this paper,flow of slightly rarefied compressible nitrogen in microchannels has been investigated numerically for low values of Reynolds and Mach numbers.The 2D governing equations were solved using Finite Element ...In this paper,flow of slightly rarefied compressible nitrogen in microchannels has been investigated numerically for low values of Reynolds and Mach numbers.The 2D governing equations were solved using Finite Element Method with first-order slip boundary conditions(Comsol Multiphysics software).A validation was performed by comparing with similar configuration from the literature.It was found that our model can accurately predict the pressure driven flow in microchannels.Several interesting findings are reported about the Relative pressure,longitudinal velocity,Mach number,effect of gas rarefaction and flow rate.展开更多
The paper studies the problem of fluid flow and fluid shear stress in canaliculi when the osteon is subject to external mechanical loading and blood pressure oscillation.The single osteon is modeled as a saturated por...The paper studies the problem of fluid flow and fluid shear stress in canaliculi when the osteon is subject to external mechanical loading and blood pressure oscillation.The single osteon is modeled as a saturated poroelastic cylinder. Solid skeleton is regarded as a poroelastic transversely isotropic material. To get near-realistic results, both the interstitial fluid and the solid matrix are regarded as compressible. Blood pressure oscillation in the Haverian canal is considered. Using the poroelasticity theory, an analytical solution of the pore fluid pressure is obtained. Assuming the fluid in canaliculi is incompressible, analytical solutions of fluid flow velocity and fluid shear stress with the Navier-Stokes equations of incompressible fluid are obtained. The effect of various parameters on the fluid flow velocity and fluid shear stress is studied.展开更多
Dedicated experiments and numerical simulations have been conducted to investigate the splitting characteristics of a gas-liquid two phase flow at a T junction.The experiments were carried out for different gas-liquid...Dedicated experiments and numerical simulations have been conducted to investigate the splitting characteristics of a gas-liquid two phase flow at a T junction.The experiments were carried out for different gas-liquid velocities.The flow rates in the two branches were measured accurately to determine how the two considered phases distribute in the two outlets.The experimental results have shown that when the two outlet pressures are asymmetric,the two-phase flow always tends to flow into the outlet which has a lower pressure.As the inlet liquid velocity increases,however,the two-phase flow gradually tends to split evenly.Compared with the experiment results,the pressure difference between the two outlets can be determined more accurately by means of numerical simulation.The trends of experimental results and simulations are in very good agreement.展开更多
This paper deals with some aspects of the air entrainment process along the chute of spillway and study of pressure fluctuations. The experimental study has been carried out using stepped spillway model located in the...This paper deals with some aspects of the air entrainment process along the chute of spillway and study of pressure fluctuations. The experimental study has been carried out using stepped spillway model located in the campus of Government College of Engineering, Amravati (India). It is observed that air concentration is increasing with discharge as well as with number of step. Air concentration is increasing along the length of spillway. It is also observed that the bottom mean air concentration increases with step height in the upstream reach of stepped spillway, which is prone to cavitation. The pressure profiles exhibit a wavy pattern down the stepped chute and pressure on each step increases with ratio of critical depth to step height (yc/h).展开更多
At a different angle, this study analyzed the contour chart of blood flow pressure, extreme pressure and its position to quantify DBFP in thirteen different postures with gravity considered or not (G ≠ 0 or G = 0). T...At a different angle, this study analyzed the contour chart of blood flow pressure, extreme pressure and its position to quantify DBFP in thirteen different postures with gravity considered or not (G ≠ 0 or G = 0). The aim was to determine the suitable body positions, in which the postural model of a single vessel could be simplified to two-dimensional (2D) symmetrical one while only considering such factors as posture and gravity. Computational fluid dynamic simulations were performed. Numerical results demonstrated that the DBFP showed 2D axisymmetry at ±90° and three-dimensional (3D) asymmetry at any other posture with G ≠ 0, and 2D axisymmetrical one at any posture with G = 0. Therefore, modeling a vessel as a 2D model is feasible in space and at ±90° posture on earth. In addition, the maximum pressure occurred between the inlet and the middle of the vessel, and its position variation mainly happened in the range of 0° - 15°. For a single vessel, this study provides the first theoretical evidence for cardiovascular modeling in microgravity and may help guide the researchers in designing defense devices for astronauts or patients clinically.展开更多
基金The research was funded by Science and Technology Project of Hebei Education Department(Project Number:QN2022198).Y.C.received the grant.
文摘This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by means of a fluid–structure interaction(FSI)method by which the descaling effect produced by rolling coils with different section sizes is examined.Assuming a flat fan-shaped nozzle at the entrance of the R1R2 roughing mill,the outflow field characteristics and the velocity distribution curve on the strike line(at a target distance of 30–120 mm)are determined.It is found that the velocity in the center region of the water jet with different target distances is higher than that in the boundary region.As the target distance increases,the velocity of the water jet in the central region decreases.Through comparison with experimental results,it is shown that the simulation model can accurately predict the impact position of the high-pressure water on the impact plate,thereby providing a computational scheme that can be used to optimize the nozzle space layout and improve the slabs’descent effect for different rolling specifications.
基金supported by National Key R&D Program of China(No.2022YFC3004705)the National Natural Science Foundation of China(Nos.52074280,52227901 and 52204249)National Natural Science Foundation of China Youth Fund(No.52104230).
文摘Effective monitoring of the structural health of combined coal-rock under complex geological conditions by pressure stimulated currents(PSCs)has great potential for the understanding of dynamic disasters in underground engineering.To reveal the effect of this way,the uniaxial compression experiments with PSC monitoring were conducted on three types of coal-rock combination samples with different strength combinations.The mechanism explanation of PSCs are investigated by resistivity test,atomic force microscopy(AFM)and computed tomography(CT)methods,and a PSC flow model based on progressive failure process is proposed.The influence of strength combinations on PSCs in the progressive failure process are emphasized.The results show the PSC responses between rock part,coal part and the two components are different,which are affected by multi-scale fracture characteristics and electrical properties.As the rock strength decreases,the progressive failure process changes obviously with the influence range of interface constraint effect decreasing,resulting in the different responses of PSC strength and direction in different parts to fracture behaviors.The PSC flow model is initially validated by the relationship between the accumulated charges of different parts.The results are expected to provide a new reference and method for mining design and roadway quality assessment.
基金support from the National Natural Science Foundation of China(Grant.No.42162027)the Science and technology foundation of Guizhou Province(Grant.No.2022-212,2023-006)are greatly appreciated.
文摘Karst sinkholes with natural negative landform provide favorable conditions for the pumped storage reservoir construction for less excavation work.However,the construction of the reservoir would plug the natural karst channels for water and air,which would cause remarkable air pressure in karst channels when the groundwater level fluctuates.A large laboratory simulation test was carried out to study the air pressure variation of a reservoir built on the karst sinkhole.The air pressure in the karst channel and inside the model was monitored during the groundwater rising and falling process.Result showed that the variation of air pressure in the karst channel and the surrounding rock exhibited a high degree of similarity.The air pressure increased rapidly at the initial stage of water level rising,followed by a slight decrease,then the air pressure increased sharply when the water level approached the top of the karst cave.The initial peak of air pressure and the final peak of air pressure were defined,and both air pressure peaks were linearly increasing with the water level rising rate.The negative air pressure was also analyzed during the drainage process,which was linearly correlated with the water level falling rate.The causes of air pressure variation in karst channels of a pumped storage reservoir built on the karst sinkhole were discussed.The initial rapid increase,then slight decrease and final sudden increase of air pressure were controlled by the combined effects of air compression in karst channel and air seepage into the surrounding rock.For the drainage process,the instant negative air pressure and gradual recovering of air pressure were controlled by the combined effects of negative air pressure induced by water level falling and air supply from surrounding rock.This work could provide valuable reference for the reservoir construction in karst area.
文摘This paper aims to propose correlations to predict pressure gradient,friction factor and fluid phase hold-up in liquid-liquid horizontal pipe flow.To develop the correlations,experiments are conducted using high viscous oils(202 and 630 mPa⋅s)in a steel pipe of length 11.25 m and length-to-diameter ratio of 708.In addition,the experimental data from the literature comprising wide range of flow and fluid properties is analyzed.For the analysis,the liquid-liquid pipe flow data is categorized into two as:stratified and dispersed.The existing friction factor correlations are modified to incorporate the effects of viscosity of the oil phase,interfacial curvature(contact/wetting angle-in lieu of material of the pipe)and fluid phase fraction.In the two-fluid model of stratified flow,the wall stress and interfacial stress correlations are substituted with superficial velocities of fluids and superficial Reynolds numbers of fluid phases replacing fluid phase velocities and fluid Reynolds numbers.Similarly,for dispersed flow,an effective Reynolds number is described as the sum of superficial Reynolds number of oil and water phases.Substituting the generally employed mean or mixture Reynolds number with the effective Reynolds number into the existing single-phase turbulent flow friction factor correlation,an effective friction factor for oil-water flow is proposed.Employing the proposed correlations,the pressure gradient across the oil-water flow and hold-up volume fraction are predicted with significant reduction in error compared with that of conventionally employed correlations.The average error and standard deviation values of−7.06%,20.72%and 0.31%,18.79%are found for stratified flow and dispersed flow respectively.
文摘A new numerical model for low-permeability reservoirs is developed.The model incorporates the nonlinear characteristics of oil-water two-phase flows while taking into account the initiation pressure gradient.Related numerical solutions are obtained using a finite difference method.The correctness of the method is demonstrated using a two-dimensional inhomogeneous low permeability example.Then,the differences in the cumulative oil and water production are investigated for different starting water saturations.It is shown that when the initial water saturation grows,the water content of the block continues to rise and the cumulative oil production gradually decreases.
基金jointly funded by the National Natural Science Foundation of China(Grant No.42201095)the Natural Science Foundation of Sichuan(Grant No.2022NSFSC1032)。
文摘The use of open-type check dams in mountainous areas has become common practice in order to mitigate the effects of debris flow and extend the service life of engineering structures.The beam dam,a common debris flow control system,has received less attention in research on the impact process of debris flow and check dams compared to solid check dams.Additionally,the estimation of impact pressure in debris flow primarily considers debris flow characteristics,without taking into account the influence of geometric characteristics of the transmission structure.To better understand the impact process of debris flow on beam dams,a series of small-scale debris flow impact tests were conducted in a model flume.Key parameters,including velocity,depth,and impact pressure,were measured.The results show that the maximum impact pressure of debris flow is affected by both the characteristics of the debris flow and the relative opening size of the beam dam.Due to flow and edge occlusion in the middle of the beam dam,the discharge of debris flow is enhanced,resulting in a longer impact process and higher maximum impact pressure.Based on these findings,a calculation model of the maximum impact pressure of debris flow at the midpoint of the middle beam is proposed,which can be used to estimate the impact of debris flow on the discharge part of the beam dam.
文摘Due to the inherent working mode of rotating detonation engine(RDE),the detonation flow field has the characteristics of pressure oscillation and axial kinetic energy loss,which makes it difficult to design nozzle and improve propulsion performance.Therefore,in order to improve the characteristics of detonation flow field,the three-dimensional numerical simulation of annular chamber and hollow chamber is carried out with premixed hydrogen/air as fuel in this paper,and then tries to combine the two chambers to weaken the oscillation characteristics of detonation flow field through the interaction of detonation flow field,which is a new method to regulate the detonation flow field.The results show that there are four states of velocity vectors at the outlet of annular chamber and hollow chamber,which makes RDE be affected by rolling moment and results in the loss of axial kinetic energy.In the external flow field of combined chamber,the phenomenon of cyclic reflection of expansion wave and compression wave on the free boundary is observed,which results in Mach disk structure.Moreover,the pressure monitoring points are set at the external flow field.The pressure signal shows that the high-frequency pressure oscillation at the external flow field of the combined chamber has been greatly weakened.Compared to the annular chamber,the relative standard deviation(RSD) has been reduced from 14.6% to5.6%.The results thus demonstrate that this method is feasible to adjust the pressure oscillation characteristics of the detonation flow field,and is of great significance to promote the potential of RDE and nozzle design.
文摘The pressure-sensitive effect on the pore structure of sandstone was investigated using X-ray computed micro-tomography and QEMSCAN quantitative mineral analysis. In a physical simulation study, we extracted the pore network model from digital cores at different confining pressures and evaluated the effect of pressure sensitivity on the multiphase displacement process. In both the pore network model and QEMSCAN scanning, the pore structure was observed to be damaged under a high confining pressure. Due to their different scales, the pores and throats exhibited inhomogeneous changes; further, the throats exhibited a significant variation compared to that exhibited by the pores. Meanwhile, the heterogeneity of the pore structure under the two aforementioned activities was aggravated by the elastic-plastic deformation of the pore structure.The pressure-sensitive effect increased the proportion of mineral particles, such as quartz(the main component of the core skeleton), and reduced the proportion of clay minerals. The clay minerals were originally attached to the pore walls or interspersed in the pores; however, as the pressure increased, the clay minerals accumulated in the pores resulting in blockage of the pores. While simulating the multiphase displacement process, increasing the confining pressure was observed to severely restrict the flowability of oil and water. This study promises to improve the efficiency of reservoir development in terms of oil and gas exploitation.
基金Supported by the National Natural Science Foundation of China(51765016,51475165,11462004)the Jiangxi Provincial Foundation for Leaders of Academic and Disciplines in Science(20162BCB22019)5511 Science and Technology Innovation Talent Project of Jiangxi Province(20165BCB18011)
文摘A compact annular-radial-orifice flow magnetorheological(MR)valve was developed to investigate the effects of radial resistance gap on pressure drop.The fluid flow paths of this proposed MR valve consist of a single annular flow channel,a single radial flow channel and an orifice flow channel through structure design.The finite element modelling and simulation analysis of the MR valve was carried out using ANSYS/Emag software to investigate the changes of the magnetic flux density and yield stress along the fluid flow paths under the four different radial resistance gaps.Moreover,the experimental tests were also conducted to evaluate the pressure drop,showing that the proposed MR valve has significantly improved its pressure drop at 0.5 mm width of the radial resistance gap when the annular resistance gap is fixed at 1 mm.
基金supported by the National Natural Science Foundation of China (Grant No. 41601011)National Natural Science Foundation of China (Grant No. 41790434)National Natural Science Foundation of China (41771045)
文摘Impact force is a crucial factor to be considered in debris-resisting structure design. The impact of debris flow against a structural barrier depends not only on the flow dynamics but also on the barrier material. Based on the structural vibration equation and energy conservation law, a simple model for calculating debris-flow impact pressure is proposed, which includes the mechanical impedance of the material, debris-flow velocity and Froude number. Twenty-five impact tests have been conducted using different kinds of materials: steel, black granite, white granite, marble and polyvinyl chloride(PVC) board, and the ratio of the maximum impact time to the vibration period of the structure is determined for the model. It is found that the ratio's square root shows a linear relationship with the material solid Froude number. This indicates that the impedance of the structures plays an important role in the flow-barrier interaction. Moreover, the debrisflow impact force is found to decrease with the travel time of the elastic stress wave though the structures.
基金supported by the open foundation of State Key Laboratory of Chemical Engineering (SKL-ChE-18B03)the Municipal Science and Technology Commission of Tianjin (No. 2009ZCKFGX01900)
文摘A cold-model vertical multi-tube circulating fluidized bed evaporator was designed and built to conduct a visualization study on the pressure drop of a liquid–solid two-phase flow and the corresponding particle distribution.Water and polyformaldehyde particle(POM)were used as the liquid and solid phases,respectively.The effects of operating parameters such as the amount of added particles,circulating flow rate,and particle size were systematically investigated.The results showed that the addition of the particles increased the pressure drop in the vertical tube bundle.The maximum pressure drop ratios were 18.65%,21.15%,18.00%,and 21.15%within the experimental range of the amount of added particles for POM1,POM2,POM3,and POM4,respectively.The pressure drop ratio basically decreased with the increase in the circulating flow rate but fluctuated with the increase in the amount of added particles and particle size.The difference in pressure drop ratio decreased with the increase in the circulating flow rate.As the amount of added particles increased,the difference in pressure drop ratio fluctuated at low circulating flow rate but basically decreased at high circulating flow rate.The pressure drop in the vertical tube bundle accounted for about 70%of the overall pressure drop in the up-flow heating chamber and was the main component of the overall pressure within the experimental range.Three-dimensional phase diagrams were established to display the variation ranges of the pressure drop and pressure drop ratio in the vertical tube bundle corresponding to the operating parameters.The research results can provide some reference for the application of the fluidized bed heat transfer technology in the industry.
基金Project(2008B-2901) supported by China National Petroleum Corporation
文摘In order to research start-up pressure wave propagation mechanism and determine pressure wave speed in gelled crude oil pipelines accurately,experiment of Large-scale flow loop was carried out.In the experiment,start-up pressure wave speeds under various operation conditions were measured,and effects of correlative factors on pressure wave were analyzed.The experimental and theoretical analysis shows that thermal shrinkage and structural properties of gelled crude oils are key factors influencing on start-up pressure wave propagation.The quantitative analysis for these effects can be done by using volume expansion coefficient and structural property parameter of gelled crude oil.A new calculation model of pressure wave speed was developed on the basis of Large-scale flow loop experiment and theoretical analysis.
基金supported by a Grant from the State Key Basic Research Program of China(No.2011CB201204)the Central University Basic Scientific Research Business Expenses(No.2011ZY05)
文摘The permeability of coal ahead of the working face obviously changes dues to changes in abutment pressure.The formation and evolution of gas flow channels within the abutment pressure area was studied by analyzing the fracture extension mechanism and fracture development in different zones of the abutment pressure area.Fracture and damage mechanics theory is used to understand the observations.The following two techniques were used to understand the evolution of gas flow channels:field observation of the characteristic fractures at different positions relative to the working face and fluorescence micrographs of prepared coal samples.Bending tensile fractures develop along an approximately vertical direction that forms a microscopic network of channels in areas of stress concentration.The abutment pressure affects the local stress and,hence,the local gas conduction.The fractures induced by large deformation and plastic flow form macroscopically networked channels in the reduced stress area.Closer to the working face the gas flow channels evolve from microscopic to macroscopic and from isolated to network.Gas permeability continuously increases during this time.This is corroborated by field observations of the displacement of top coal and the gas flow from gas extraction drillings.
基金financially supported by the National Natural Science Foundation of China(Grant No.51974090,51474073)
文摘With ongoing development of oil exploration and techniques,there is a significant need for improved well control strategies and formation pressure prediction methods.In this paper,a gas-liquid transient drift flow model was established according to the gas-liquid two-phase flow characteristics during the gas kick.A Roe scheme was used for numerical calculation based on the finite volume method.The changes of bottom-hole pressure,casing pressure,the development law of cross-sectional gas holdup,and gas velocity,along with the vertical well depth,were analyzed through simulation examples.The time-series characteristics of mud pit gain were obtained by adjusting the formation parameter.The complex nonlinear mapping relationship between the formation parameters and the mud pit gain was established.The long short-term memory network(LSTM)of deep learning was used to obtain a formation pressure inversion when the blowout is out of control and the well cannot be shut-in.Experimental data from a well were used to verify the gas-liquid two-phase transient drift flow model based on the finite volume method,demonstrating that this method is reliable,with greatly improved prediction accuracy.This approach provides theoretical support for the early monitoring of gas kick during drilling,and for well-killing design and construction after uncontrolled blowout.
文摘In this paper,flow of slightly rarefied compressible nitrogen in microchannels has been investigated numerically for low values of Reynolds and Mach numbers.The 2D governing equations were solved using Finite Element Method with first-order slip boundary conditions(Comsol Multiphysics software).A validation was performed by comparing with similar configuration from the literature.It was found that our model can accurately predict the pressure driven flow in microchannels.Several interesting findings are reported about the Relative pressure,longitudinal velocity,Mach number,effect of gas rarefaction and flow rate.
基金Project supported by the National Natural Science Foundation of China(No.11032005)
文摘The paper studies the problem of fluid flow and fluid shear stress in canaliculi when the osteon is subject to external mechanical loading and blood pressure oscillation.The single osteon is modeled as a saturated poroelastic cylinder. Solid skeleton is regarded as a poroelastic transversely isotropic material. To get near-realistic results, both the interstitial fluid and the solid matrix are regarded as compressible. Blood pressure oscillation in the Haverian canal is considered. Using the poroelasticity theory, an analytical solution of the pore fluid pressure is obtained. Assuming the fluid in canaliculi is incompressible, analytical solutions of fluid flow velocity and fluid shear stress with the Navier-Stokes equations of incompressible fluid are obtained. The effect of various parameters on the fluid flow velocity and fluid shear stress is studied.
基金the National Science and Technology Major Project of China(No.2016ZX05028-004-003).
文摘Dedicated experiments and numerical simulations have been conducted to investigate the splitting characteristics of a gas-liquid two phase flow at a T junction.The experiments were carried out for different gas-liquid velocities.The flow rates in the two branches were measured accurately to determine how the two considered phases distribute in the two outlets.The experimental results have shown that when the two outlet pressures are asymmetric,the two-phase flow always tends to flow into the outlet which has a lower pressure.As the inlet liquid velocity increases,however,the two-phase flow gradually tends to split evenly.Compared with the experiment results,the pressure difference between the two outlets can be determined more accurately by means of numerical simulation.The trends of experimental results and simulations are in very good agreement.
文摘This paper deals with some aspects of the air entrainment process along the chute of spillway and study of pressure fluctuations. The experimental study has been carried out using stepped spillway model located in the campus of Government College of Engineering, Amravati (India). It is observed that air concentration is increasing with discharge as well as with number of step. Air concentration is increasing along the length of spillway. It is also observed that the bottom mean air concentration increases with step height in the upstream reach of stepped spillway, which is prone to cavitation. The pressure profiles exhibit a wavy pattern down the stepped chute and pressure on each step increases with ratio of critical depth to step height (yc/h).
文摘At a different angle, this study analyzed the contour chart of blood flow pressure, extreme pressure and its position to quantify DBFP in thirteen different postures with gravity considered or not (G ≠ 0 or G = 0). The aim was to determine the suitable body positions, in which the postural model of a single vessel could be simplified to two-dimensional (2D) symmetrical one while only considering such factors as posture and gravity. Computational fluid dynamic simulations were performed. Numerical results demonstrated that the DBFP showed 2D axisymmetry at ±90° and three-dimensional (3D) asymmetry at any other posture with G ≠ 0, and 2D axisymmetrical one at any posture with G = 0. Therefore, modeling a vessel as a 2D model is feasible in space and at ±90° posture on earth. In addition, the maximum pressure occurred between the inlet and the middle of the vessel, and its position variation mainly happened in the range of 0° - 15°. For a single vessel, this study provides the first theoretical evidence for cardiovascular modeling in microgravity and may help guide the researchers in designing defense devices for astronauts or patients clinically.