Influence of aerodynamic configuration of a streamline box girder on bridge flutter and vortex-induced vibration

Streamline box girders are widely applied in the design and construction of long-span bridges all over the world. In order to study the influence of modifications of aerodynamic configuration and accessory components on flutter and vortex-induced vibration （VIV）, more than 60 cases were tested through a 1：50 scale section model. The test results indicates that the aerodynamic configuration and accessory components of streamline box girders can signifi- cantly affect the wind-induced vibration of bridge, which is in good agreement with the experience of past researchers. From the tests carried out, it is observed that if the horizontal angle of the inclined web of the streamline box girder is below 16°, the critical flutter wind speed of bridge will increase remarkably, and the VIV will diminish. The test results also show that the 15° inclined web can restrain the formation of vortex near the tail, and consequently improve the performance of aerodynamic stability of long-span bridges. Finally, a new streamline box girder with 15° inclined web was presented and strongly recommended in the aerodynamic configuration design of long-span bridges.

Dynamic finite element model updating of prestressed concrete continuous box-girder bridge

The dynamic finite element model （FEM） of a prestressed concrete continuous box-girder bridge, called the Tongyang Canal Bridge, is built and updated based on the results of ambient vibration testing （AVT） using a real-coded accelerating genetic algorithm （RAGA）. The objective functions are defined based on natural frequency and modal assurance criterion （MAC） metrics to evaluate the updated FEM. Two objective functions are defined to fully account for the relative errors and standard deviations of the natural frequencies and MAC between the AVT results and the updated FEM predictions. The dynamically updated FEM of the bridge can better represent its structural dynamics and serve as a baseline in long-term health monitoring, condition assessment and damage identification over the service life of the bridge .

Closed-form solution to thin-walled box girders considering effects of shear deformation and shear lag

Considering three longitudinal displacement functions and uniform axial displacement functions for shear lag effect and uniform axial deformation of thin-walled box girder with varying depths,a simple and efficient method with high precision to analyze the shear lag effect of thin-walled box girders was proposed.The governing differential equations and boundary conditions of the box girder under lateral loading were derived based on the energy-variational method,and closed-form solutions to stress and deflection corresponding to lateral loading were obtained.Analysis and calculations were carried out with respect to a trapezoidal box girder under concentrated loading or uniform loading and a rectangular box girder under concentrated loading.The analytical results were compared with numerical solutions derived according to the high order finite strip element method and the experimental results.The investigation shows that the closed-form solution is in good agreement with the numerical solutions derived according to the high order finite strip method and the experimental results,and has good stability.Because of the shear lag effect,the stress in cross-section centroid is no longer zero,thus it is not reasonable enough to assume that the strain in cross-section centroid is zero without considering uniform axial deformation.

Bone marrow-derived mesenchymal stem cell-derived exosomeloaded miR-129-5p targets high-mobility group box 1 attenuates neurological-impairment after diabetic cerebral hemorrhage

BACKGROUND Diabetic intracerebral hemorrhage(ICH)is a serious complication of diabetes.The role and mechanism of bone marrow mesenchymal stem cell(BMSC)-derived exosomes(BMSC-exo)in neuroinflammation post-ICH in patients with diabetes are unknown.In this study,we investigated the regulation of BMSC-exo on hyperglycemia-induced neuroinflammation.AIM To study the mechanism of BMSC-exo on nerve function damage after diabetes complicated with cerebral hemorrhage.METHODS BMSC-exo were isolated from mouse BMSC media.This was followed by transfection with microRNA-129-5p(miR-129-5p).BMSC-exo or miR-129-5poverexpressing BMSC-exo were intravitreally injected into a diabetes mouse model with ICH for in vivo analyses and were cocultured with high glucoseaffected BV2 cells for in vitro analyses.The dual luciferase test and RNA immunoprecipitation test verified the targeted binding relationship between miR-129-5p and high-mobility group box 1(HMGB1).Quantitative polymerase chain reaction,western blotting,and enzyme-linked immunosorbent assay were conducted to assess the levels of some inflammation factors,such as HMGB1,interleukin 6,interleukin 1β,toll-like receptor 4,and tumor necrosis factorα.Brain water content,neural function deficit score,and Evans blue were used to measure the neural function of mice.RESULTS Our findings indicated that BMSC-exo can promote neuroinflammation and functional recovery.MicroRNA chip analysis of BMSC-exo identified miR-129-5p as the specific microRNA with a protective role in neuroinflammation.Overexpression of miR-129-5p in BMSC-exo reduced the inflammatory response and neurological impairment in comorbid diabetes and ICH cases.Furthermore,we found that miR-129-5p had a targeted binding relationship with HMGB1 mRNA.CONCLUSION We demonstrated that BMSC-exo can reduce the inflammatory response after ICH with diabetes,thereby improving the neurological function of the brain.

Estimating extreme temperature differences in steel box girder using long-term measurement data

The extreme temperature differences in fiat steel box girder of a cable-stayed bridge were studied.Firstly,by using the long-term measurement data collected by the structural health monitoring system installed on the Runyang Cable-stayed Bridge,the daily variations as well as seasonal ones of measured temperature differences in the box girder cross-section area were summarized.The probability distribution models of temperature differences were further established and the extreme temperature differences were estimated with a return period of 100 years.Finally,the temperature difference models in cross-section area were proposed for bridge thermal design.The results show that horizontal temperature differences in top plate and vertical temperature differences between top plate and bottom plate are considerable.All the positive and negative temperature differences can be described by the weighted sum of two Weibull distributions.The maximum positive and negative horizontal temperature differences in top plate are 10.30 ℃ and -13.80 ℃,respectively.And the maximum positive and negative vertical temperature differences between top plate and bottom plate are 17.30 ℃ and-3.70 ℃,respectively.For bridge thermal design,there are two vertical temperature difference models between top plate and bottom plate,and six horizontal temperature difference models in top plate.

Explosion resistance performance of reinforced concrete box girder coated with polyurea:Model test and numerical simulation

To study the anti-explosion protection effect of polyurea coating on reinforced concrete box girder,two segmental girder specimens were made at a scale of 1:3,numbered as G(without polyurea coating)and PCG(with polyurea coating).The failure characteristics and dynamic responses of the specimens were compared through conducting explosion tests.The reliability of the numerical simulation using LS-DYNA software was verified by the test results.The effects of different scaled distances,reinforcement ratios,concrete strengths,coating thicknesses and ranges of polyurea were studied.The results show that the polyurea coating can effectively enhance the anti-explosion performance of the girder.The top plate of middle chamber in specimen G forms an elliptical penetrating hole,while that in specimen PCG only shows a very slight local dent.The peak vertical displacement and residual displacement of PCG decrease by 74.8% and 73.7%,respectively,compared with those of specimen G.For the TNT explosion with small equivalent,the polyurea coating has a more significant protective effect on reducing the size of fracture.With the increase of TNT equivalent,the protective effect of polyurea on reducing girder displacement becomes more significant.The optimal reinforcement ratio,concrete strength,thickness and range of polyurea coating were also drawn.

Fatigue Crack Propagation Law of Corroded Steel Box Girders in Long Span Bridges

In order to investigate the fatigue performance of orthotropic anisotropic steel bridge decks,this study realizes the simulation of the welding process through elastic-plastic finite element theory,thermal-structural sequential coupling,and the birth-death element method.The simulated welding residual stresses are introduced into the multiscale finite element model of the bridge as the initial stress.Furthermore,the study explores the impact of residual stress on crack propagation in the fatigue-vulnerable components of the corroded steel box girder.The results indicate that fatigue cracks at the weld toe of the top deck,the weld root of the top deck,and the opening of the transverse diaphragm will not propagate under the action of a standard vehicle load.However,the inclusion of residual stress leads to the propagation of these cracks.When considering residual stress,the fatigue crack propagation paths at the weld toe of the transverse diaphragm and the U-rib weld toe align with those observed in actual bridges.In the absence of residual stress,the cracks at the toe of the transverse diaphragm with a 15%mass loss rate are categorized as type I cracks.Conversely,when residual stress is considered,these cracks become I-II composite cracks.Residual stress significantly alters the cumulative energy release rate of the three fracturemodes.Therefore,incorporating the influence of residual stress is essential when assessing the fatigue performance of corroded steel box girders in long-span bridges.

Vibro-acoustic performance of steel–concrete composite and prestressed concrete box girders subjected to train excitations

Owning to good mechanical properties,steel–concrete composite(SCC)and prestressed concrete(PC)box girders are the types of elevated structures used most in urban rail transit.However,their vibro-acoustic differences are yet to be explored in depth,while structure-radiated noise is becoming a main concern in noise-sensitive environments.In this work,numerical simulation is used to investigate the vibration and noise characteristics of both types of box girders induced by running trains,and the numerical procedure is verified with data measured from a PC box girder.The mechanism of vibration transmission and vibro-acoustic comparisons between SCC and PC box girders are investigated in detail,revealing that more vibration and noise arise from SCC box girders.The vibration differences between them are around 7.7 dB(A)at the bottom plate,19.3 dB(A)at the web,and 6.7 dB(A)at the flange,while for structure-radiated noise,the difference is around 5.9 dB(A).Then,potential vibroacoustic control strategies for SCC box girders are discussed.As the vibro-acoustic responses of two types of girders are dominated by the force transmitted to the bridge deck,track isolation is better than structural enhancement.It is shown that using a floating track slab can make the vibration and noise of an SCC box girder lower than those of a PC box girder.However,structural enhancement for the SCC box girder is extremely limited in effects.The six proposed structural enhancement measures reduce vibration by only 1.1–3.6 dB(A) and noise by up to1.5 dB(A).

Fatigue Performance of Orthotropic Steel Decks in Super-Wide Steel Box Girder Considering Transverse Distribution of Vehicle Load

This study presents an investigation on the fatigue analysis of four types of details on orthotropic steel decks(OSDs)for a cable-stayed super-wide steel box girder bridge based on finite-element analysis(FEA)with vehicle transverse distribution model(VTDM).A high-fidelity 3D FE model verified by the static load test is established to satisfy the fatigue analysis accuracy.The stress behavior of super-wide steel box girders under the vehicle load at different lane locations is investigated.Then,considering the effect of VTDM,the fatigue life analysis of four typical details is performed using the Miner cumulative damage rule.The results show that the vehicle transverse location has a great influence on the stress behavior of details with sharp influence surface,and the stress ranges in the outermost lane are larger than those in other lanes,indicating that the details of OSD in the outermost lane are prone to fatigue.The fatigue life analysis indicates that the diaphragm cutout is more prone to fatigue than other details,which should be carefully treated in bridge maintenance.

Lateral static and dynamic characteristics of thin-walled box girder

To analyze the static and dynamic behaviors of the thin-walled box girder in its lateral webs in consideration of shear lag effect and shear deformation, an approach based on the minimum potential principle is introduced in this paper. Both static and dynamic response equations as well as the corresponding natural boundary conditions of the box girder are deduced. Meanwhile, three generalized displacement functions： w （x） , U（x） and O（x） are employed and their differences in the calculus of variation are quantitatively investigated. The comparison of finite shell element results with analytical results of calculation examples validates the feasibility of the proposed approach.

Design and Research of Class 900 t Railway Box-girder Bridge Erecting Machine

In this article, the current railway box girder bridge erecting machines at home and abroad are briefly introduced and analyzed, the research & design situation of class 900t railway box girder bridge erecting machines is described, and also the principle for determining the overall plan and a series of issues much concerning the design of key components of class 900t railway box girder bridge erecting machines are described.

Strengthening of Concrete Box Girder Bridges under Close-in Detonations

The response of a bridge superstructure under blast loading might depend largely on the extent of the local damage experienced due to close-in explosion threats. This paper investigates the local and structural response of box girder bridge decks strengthened using CFRP （carbon fiber reinforced polymers） under close-in detonations. Due to the lack of experimental research on this topic, the study is conducted using the explicit finite element computer program LS-DY-NA. The numerical study will be verified using the results of strengthened reinforced concrete slabs under field detonations. The blast load was assumed to be detonated above the bridge deck. The key parameters investigated are the charge size, and the strengthening location on the deck. This paper will present the results of this investigation and provides recommendations for predicting the local damage level based on the CFRP strengthening design under blast threat.

Discussion on Detection and Evaluation of Simply Supported Prestressed Concrete Small Box Girder Bridge After a Fire

The article takes a simply supported prestressed concrete small box girder bridge project as an example for inspection and evaluation after a fire incident.This includes appearance detection,concrete color hardness detection,concrete strength detection,concrete surface damage layer detection,reinforcement protective layer detection,and concrete carbonation detection.It is hoped that this analysis can be used as a reference for the detection and evaluation of future bridge projects with fire incidents to smoothen its subsequent repair and maintenance.

Simulation of Temperature Field in Original Segment of Concrete Box-Girder Bridge

Temperature field and its variation with time are necessary for analyzing the thermo-mechanical performance of mass concrete structures at their early ages. This paper carries out a temperature field simulation analysis for an original segment of a real box girder bridge with the finite element software ANSYS. Two representative exothermic rate models are used to describe the heat- releasing process caused by the cement hydration in concrete. The exothermic rate model that conforms to reality more closely is recognized by comparing the simulation results with the data gathered from the optical fiber temperature sensors pre-embedded in the original segment. The air temperature and wind velocity that constitute thermal boundary conditions are determined in the light of the local meteorological department and correlative research achievements of recent years. Moreover, the consideration for the steel formwork acting as a barrier to heat loss is also proved to be beneficial to improve the simulation effect.

A comparative study on the hull strength of a ship with thin-walled box girders

Based on the Finite Element Analysis and Thin Walled-Box girder Mechanics, two design concepts of adding box girders under main deck in order to increase the hull strength of ship are presented. By comparison and analysis on the longitudinal strength, torsion strength and deck buckling between designed concepts and the original concept, it is found that by adding box girders under the main deck, the weight of hull structure is increased by lower than 10%, but the stress on the plate of the main deck is reduced by about 10%, the stress on the plating of the second deck is reduced about 20%. The shear stress on the plating of both of the main deck and second deck is reduced, but the shear stresses in several nodes are increased. Also the capability of resisting damage to ship is obviously increased by adding box girders under the main deck. The deck buckling is also increased by more than 90%. Consequently, the box girders added under the main deck are useful and effective to increase the strength of hull and ship survivability.

Full-scale model tests and nonlinear analysis of prestressed concrete simply supported box girders

Full-scale model tests were carried out on a 30 m span prestressed concrete box girder and a 20 m span prestressed concrete hollow slab. Failure models were prestressed reinforcement tensile failure and crashing of roof concrete, respectively. The ductility indexes of the box girder and hollow slab were 1.99 and 1.23, respectively, according to the energy viewpoint. Based on the horizontal section hypothesis, the nonlinear computation procedure was established using the limited banding law, and it could carry out the entire performance analysis including the unloading, mainly focusing on the ways to achieve the unloading curves computation through stress-strain, moment-curvature and load-displacement curves. Through the procedure, parameters that influence on the bearing capacity, deformation performance and ductility of the structures were analyzed. Those parameters were quantity of prestressed reinforcement and tension coefficients of prestressed reinforcement. From the analysis, some useful conclusions can be obtained.

Finite element failure analysis of continuous prestressed concrete box girders

In order to analyze the load carrying capacity of prestressed concrete box girders, failure behaviors of in-situ deteriorated continuous prestressed concrete box girders under loading are experimentally observed and a finite failure analysis method for predicting behaviors of box girders is developed. A degenerated solid shell element is used to simulate box girders and material nonlinearity is considered. Since pre-stressed concrete box girders usually have a large number of curve prestressed tendons, a type of combined element is presented to simulate the prestressed tendons of box girders, and then the number of elements can be significantly reduced. The analytical results are compared with full-scale failure test results. The comparison shows that the presented method can be effectively applied to the failure analysis of in-situ continuous prestressed concrete box girders, and it also shows that the studied old bridge still has enough load carrying capacity.

Box-Behnken响应面优化超声联合双酶法提取当归地上部分总黄酮及其抗氧化活性研究

试验以当归废弃物(当归地上部分)为试验材料,在单因素试验基础上,设计Box-Behnken响应面试验,优化超声联合双酶法提取当归地上部分总黄酮的最佳提取工艺,采用DPPH和ABTS自由基法和FRAP法评价当归地上部分总黄酮的抗氧化活性。结果显示,利用超声联合双酶法提取当归地上部分总黄酮的最佳条件为乙醇浓度50%、液料比50∶1、超声时间41 min、双酶(纤维素酶∶果胶酶=2∶1)用量0.68 g/L、酶解时间93 min,此条件下,当归地上部分总黄酮提取率为8.18%。当归地上部分具有较高的抗氧化活性,在浓度为150 mg/L时,对DPPH自由基清除率为90.3%,略低于VC。在浓度为3 000 mg/L时,对ABTS清除率为88.6%,ABTS的IC50为DPPH IC50近30倍,FRAP抗氧化能力为4.64 (mg VC eq/g sample)。试验表明,当归地上部分的总黄酮具有抗氧化活性。

简支变结构连续小箱梁桥负弯矩区UHPC-NC组合桥面板抗裂性研究

针对当前简支变结构连续小箱梁桥负弯矩区钢束易堵孔、运营中桥面开裂病害等问题,提出一种无负弯矩钢束的UHPC-NC组合桥面板结构。以一座3×30 m简支变结构连续小箱梁桥为研究对象,以正常使用极限状态梁体不开裂为控制准则确定UHPC合理构造尺寸,对所提出的负弯矩组合桥面板结构进行1∶2的缩尺模型试验。试验显示:裂缝首先出现于UHPC-NC交界面处的普通混凝土部分,随后逐渐向UHPC层沿伸,且C50混凝土开裂、梁体破坏对应的截面弯矩分别为3 520,9 152 kN·m(考虑1∶8弯矩缩尺比),大于正常使用极限状态、承载能力极限状态梁体截面弯矩3 300,5 838 kN·m,即该组合桥面板结构满足小箱梁的抗裂与承载能力要求。基于试验结果建立精细化有限元模型,采用参数分析法研究UHPC厚度对梁体开裂荷载、极限承载力等方面的影响。结果表明:梁体开裂弯矩主要由UHPC上覆层厚度决定,相较于普通钢筋混凝土梁,5 cm厚的UHPC上覆层可将梁体开裂弯矩提高28.9%,7.5 cm厚的UHPC上覆层可将梁体开裂弯矩提高41.6%;在配筋率不变的情况下,增大UHPC层厚度对梁体承载力无显著提升。综合考虑梁体受力性能以及施工便利性,建议背景工程UHPC厚度取10 cm。