A high power waveguide directional coupler was designed to measure the transmitted power and reflected power in the 4.6 GHz LHCD （lower hybrid current drive） launcher for the EAST tokamak. The design principle of th...A high power waveguide directional coupler was designed to measure the transmitted power and reflected power in the 4.6 GHz LHCD （lower hybrid current drive） launcher for the EAST tokamak. The design principle of the coupler is assessed. Further analysis is performed by CST （computer simulating test） and Ansoft HFSS （high frequency structure simulator） software and the optimal structural parameter is obtained. In addition, finite element code ANSYS is used to determine the temperature distribution in the coupler conductively cooled by forced water. The test results of a directional coupler manufactured according to the design are close to what is expected.展开更多
The preparation of a nonlinear directional coupler in polymer PMMA/DR1 film by photobleaching is studied. We find it easier to obtain a required coupling length by controlling photo bleaching time than by controlling ...The preparation of a nonlinear directional coupler in polymer PMMA/DR1 film by photobleaching is studied. We find it easier to obtain a required coupling length by controlling photo bleaching time than by controlling the dimension of the coupler. The transmittance of each arm is measured when the pulse input light energy changes in our experiment. The experimental results show that the coupling length will change with the intensity of input light due to optical nonlinearities of the polymer PMMA/DR1 at 1 064 nm.展开更多
The nonideal effects in a quantum field-effect directional coupler where two quantum wires are coupled through a finite potential barrier are studied by adopting the lattice Green function method. The results show tha...The nonideal effects in a quantum field-effect directional coupler where two quantum wires are coupled through a finite potential barrier are studied by adopting the lattice Green function method. The results show that the electron energy distribution, asymmetric geometry and finite temperature all have obvious influence on the electron transfer of the coupler. Only for the electrons with energies in a certain region, can the complete periodic transfer between two quantum wires take place. The conductance of these electrons as a function of the barrier length and potential height exhibits a fine periodic or quasi-periodic pattern. For the electrons with energies beyond the region, however, the complete periodic transfer does not hold any more since many irregular oscillations are superimposed on the conductance profile. In addition, the finite temperature and asymmetric geometry both can reduce the electron transfer efficiency.展开更多
SOI zero-gap directional couplers are studied by using large cross-section single-mode rib waveguide theory and dual-mode interference principle in silicon direct bonding SOI by back-polishing. And they are fabricated...SOI zero-gap directional couplers are studied by using large cross-section single-mode rib waveguide theory and dual-mode interference principle in silicon direct bonding SOI by back-polishing. And they are fabricated by using KOH anistropic etching. The insertion loss is measured to 4.81 dB, and the crosstalk is below —18.6 dB at a wavelength of 1.3μm.展开更多
In this paper a compact polarization beam splitter based on a deformed photonic crystal directional coupler is designed and simulated. The transverse-electric （TE） guided mode and transverse-magnetic （TM） guided m...In this paper a compact polarization beam splitter based on a deformed photonic crystal directional coupler is designed and simulated. The transverse-electric （TE） guided mode and transverse-magnetic （TM） guided mode are split due to different guiding mechanisms. The effect of the shape deformation of the air holes on the coupler is studied. It discovered that the coupling strength of the coupled waveguldes is strongly enhanced by introducing elliptical airholes, which reduce the device length to less than 18.Sttm. A finite-difference tlme-domain simulation is performed to evaluate the performance of the device, and the extinction ratios for both TE and TM polarized light are higher than 20 dB.展开更多
The E-plane waveguide branch directional couplers are analyzed by a method which combines the multimode network theory with rigorous mode-matching approach. The electromagnetic field components are expanded by the sup...The E-plane waveguide branch directional couplers are analyzed by a method which combines the multimode network theory with rigorous mode-matching approach. The electromagnetic field components are expanded by the superposition of LSEx modes rather than TE and TM modes in the mode-matching procedure. Meanwhile, the electromagnetic problem is transferred into the network problem through the mode-matching treatment. It is shown that the present method has the advantages of simplicity and less computation without affecting the accuracy of the calculation.展开更多
An analysis of a 3 dB lumped-element directional coupler （LEDC） based on arbitrary terminal impedance is described numerically. To solve the conflicted requirement for broad bandwidth and small size in LEDC, a new s...An analysis of a 3 dB lumped-element directional coupler （LEDC） based on arbitrary terminal impedance is described numerically. To solve the conflicted requirement for broad bandwidth and small size in LEDC, a new structure of coupler is introduced, which can significantly improve bandwidth and whose size is only 3 cm×4 cm on the conditions of the frequency domain of 410 MHz to 490 MHz. The measure results are in good agreement with simulations despite the unexpected resistor loss.展开更多
Power measurement is necessary for an electron cyclotron resonance heating(ECRH)system.The directional coupler method has been put forward to monitor high-power microwave from gyrotrons in real time.A multi-hole direc...Power measurement is necessary for an electron cyclotron resonance heating(ECRH)system.The directional coupler method has been put forward to monitor high-power microwave from gyrotrons in real time.A multi-hole directional coupler has been designed and manufactured for the 105 GHz/500 kW ECRH system on the J-TEXT tokamak.During the design process,we established the relationships between hole parameters and coupling characteristics based on the multi-hole coupling method and small-hole coupling theory.High-power tests have been carried out.The results indicated the reasonability of the theoretical design and practicality of the fabricated directional coupler.Sources of test errors have been discussed in detail,and the influences of spurious modes on the directional couplers have been emphatically analyzed.展开更多
In order to overcome the main drawbacks of coaxial, waveguide, and stripline couplers, the analysis and the design of a compact coaxial-to-microstrip directional coupler convenient for power and antenna control applic...In order to overcome the main drawbacks of coaxial, waveguide, and stripline couplers, the analysis and the design of a compact coaxial-to-microstrip directional coupler convenient for power and antenna control application, are presented using the method of moments (MoM) in two dimensions. This technique is adapted to study the complex configuration of the line’s system, which does not have a simple analytical solution. The modeling of this structure consists in analyzing the primary inductive and capacitive matrices ([L] and [C]). When these matrices are determined, it is possible to calculate the inductive and capacitive coupling coefficients (kL and kC) and estimate the resulting scattering parameters of the coupler using an adapted numerical model. The coupler can be integrated into a printed circuit board (PCB) and operates over 17 to 35 dB coupling coefficients and is always compensated. The compensation is achieved by the proper displacement of a tuning ground plane with respect to the edge of the PCB from 0.1 to 3.3 mm. As an application, we present the design of a compact coupler with 7.5 × 4.8 × 25.8 mm of size and having approximately 20 dB of coupling coefficient at 2 GHz and a minimum directivity of 23.3 dB in the frequency range [0.1 - 4] GHz. In order to check our numerical calculations by the MoM we made simulations in 3D by using CST MICROWAVE STUDIO software for the same geometrical and physical parameters of our designed coupler. The results obtained by the two numerical models (MoM and CST) show a good agreement of the frequency responses of the coaxial-to-microstrip directional coupler. The studied structure represents a great improvement for high power measurement systems, since it has broad-band, good directivity, and can be easily designed and fabricated.展开更多
Characteristics of optical switching in a twin-core fibre coupler are numerically analysed under short pulse input by using supermode theory. The dynamic nonlinear coupled superlnode equations are derived, The numeric...Characteristics of optical switching in a twin-core fibre coupler are numerically analysed under short pulse input by using supermode theory. The dynamic nonlinear coupled superlnode equations are derived, The numerical results show that the input pulse width determines the power transfer and the pulse temporal profile in the output ports. The optimal switching characteristics can be obtained by selecting an appropriate initial pulse width. In addition, the switching characteristic curves are insensitive to the input pulse shape for either fundamental soliton pulse or Gaussian pulse input, but sensitive to pulse sharpness. A reduced switching power and a sharper switching transition can be obtained by using the sharp super-Gaussian pulse.展开更多
文摘A high power waveguide directional coupler was designed to measure the transmitted power and reflected power in the 4.6 GHz LHCD （lower hybrid current drive） launcher for the EAST tokamak. The design principle of the coupler is assessed. Further analysis is performed by CST （computer simulating test） and Ansoft HFSS （high frequency structure simulator） software and the optimal structural parameter is obtained. In addition, finite element code ANSYS is used to determine the temperature distribution in the coupler conductively cooled by forced water. The test results of a directional coupler manufactured according to the design are close to what is expected.
文摘The preparation of a nonlinear directional coupler in polymer PMMA/DR1 film by photobleaching is studied. We find it easier to obtain a required coupling length by controlling photo bleaching time than by controlling the dimension of the coupler. The transmittance of each arm is measured when the pulse input light energy changes in our experiment. The experimental results show that the coupling length will change with the intensity of input light due to optical nonlinearities of the polymer PMMA/DR1 at 1 064 nm.
文摘The nonideal effects in a quantum field-effect directional coupler where two quantum wires are coupled through a finite potential barrier are studied by adopting the lattice Green function method. The results show that the electron energy distribution, asymmetric geometry and finite temperature all have obvious influence on the electron transfer of the coupler. Only for the electrons with energies in a certain region, can the complete periodic transfer between two quantum wires take place. The conductance of these electrons as a function of the barrier length and potential height exhibits a fine periodic or quasi-periodic pattern. For the electrons with energies beyond the region, however, the complete periodic transfer does not hold any more since many irregular oscillations are superimposed on the conductance profile. In addition, the finite temperature and asymmetric geometry both can reduce the electron transfer efficiency.
基金the High Technology Research and Development Programme of China
文摘SOI zero-gap directional couplers are studied by using large cross-section single-mode rib waveguide theory and dual-mode interference principle in silicon direct bonding SOI by back-polishing. And they are fabricated by using KOH anistropic etching. The insertion loss is measured to 4.81 dB, and the crosstalk is below —18.6 dB at a wavelength of 1.3μm.
基金supported by National Key Basic Research Special Fund of China (Grand No 2006CB921701-705)
文摘In this paper a compact polarization beam splitter based on a deformed photonic crystal directional coupler is designed and simulated. The transverse-electric （TE） guided mode and transverse-magnetic （TM） guided mode are split due to different guiding mechanisms. The effect of the shape deformation of the air holes on the coupler is studied. It discovered that the coupling strength of the coupled waveguldes is strongly enhanced by introducing elliptical airholes, which reduce the device length to less than 18.Sttm. A finite-difference tlme-domain simulation is performed to evaluate the performance of the device, and the extinction ratios for both TE and TM polarized light are higher than 20 dB.
文摘The E-plane waveguide branch directional couplers are analyzed by a method which combines the multimode network theory with rigorous mode-matching approach. The electromagnetic field components are expanded by the superposition of LSEx modes rather than TE and TM modes in the mode-matching procedure. Meanwhile, the electromagnetic problem is transferred into the network problem through the mode-matching treatment. It is shown that the present method has the advantages of simplicity and less computation without affecting the accuracy of the calculation.
文摘An analysis of a 3 dB lumped-element directional coupler （LEDC） based on arbitrary terminal impedance is described numerically. To solve the conflicted requirement for broad bandwidth and small size in LEDC, a new structure of coupler is introduced, which can significantly improve bandwidth and whose size is only 3 cm×4 cm on the conditions of the frequency domain of 410 MHz to 490 MHz. The measure results are in good agreement with simulations despite the unexpected resistor loss.
基金supported by the National Key Research and Development Program of China (Nos.2017YFE0300200 and 2017YFE0300204)in part by National Natural Science Foundation of China(No.51821005).
文摘Power measurement is necessary for an electron cyclotron resonance heating(ECRH)system.The directional coupler method has been put forward to monitor high-power microwave from gyrotrons in real time.A multi-hole directional coupler has been designed and manufactured for the 105 GHz/500 kW ECRH system on the J-TEXT tokamak.During the design process,we established the relationships between hole parameters and coupling characteristics based on the multi-hole coupling method and small-hole coupling theory.High-power tests have been carried out.The results indicated the reasonability of the theoretical design and practicality of the fabricated directional coupler.Sources of test errors have been discussed in detail,and the influences of spurious modes on the directional couplers have been emphatically analyzed.
文摘In order to overcome the main drawbacks of coaxial, waveguide, and stripline couplers, the analysis and the design of a compact coaxial-to-microstrip directional coupler convenient for power and antenna control application, are presented using the method of moments (MoM) in two dimensions. This technique is adapted to study the complex configuration of the line’s system, which does not have a simple analytical solution. The modeling of this structure consists in analyzing the primary inductive and capacitive matrices ([L] and [C]). When these matrices are determined, it is possible to calculate the inductive and capacitive coupling coefficients (kL and kC) and estimate the resulting scattering parameters of the coupler using an adapted numerical model. The coupler can be integrated into a printed circuit board (PCB) and operates over 17 to 35 dB coupling coefficients and is always compensated. The compensation is achieved by the proper displacement of a tuning ground plane with respect to the edge of the PCB from 0.1 to 3.3 mm. As an application, we present the design of a compact coupler with 7.5 × 4.8 × 25.8 mm of size and having approximately 20 dB of coupling coefficient at 2 GHz and a minimum directivity of 23.3 dB in the frequency range [0.1 - 4] GHz. In order to check our numerical calculations by the MoM we made simulations in 3D by using CST MICROWAVE STUDIO software for the same geometrical and physical parameters of our designed coupler. The results obtained by the two numerical models (MoM and CST) show a good agreement of the frequency responses of the coaxial-to-microstrip directional coupler. The studied structure represents a great improvement for high power measurement systems, since it has broad-band, good directivity, and can be easily designed and fabricated.
基金Supported by the Natural Science Foundation of Guangdong Province （04010397）, and the Excellent Teacher Foundation of Guangdong Province （Q02084）.
文摘Characteristics of optical switching in a twin-core fibre coupler are numerically analysed under short pulse input by using supermode theory. The dynamic nonlinear coupled superlnode equations are derived, The numerical results show that the input pulse width determines the power transfer and the pulse temporal profile in the output ports. The optimal switching characteristics can be obtained by selecting an appropriate initial pulse width. In addition, the switching characteristic curves are insensitive to the input pulse shape for either fundamental soliton pulse or Gaussian pulse input, but sensitive to pulse sharpness. A reduced switching power and a sharper switching transition can be obtained by using the sharp super-Gaussian pulse.
