In order to study the effects of the process parameters on springback and section deformation, a sensitivity analysis model was established based on the combination use of the multi-parameter sensitivity analysis meth...In order to study the effects of the process parameters on springback and section deformation, a sensitivity analysis model was established based on the combination use of the multi-parameter sensitivity analysis method and the springback/section deformation prediction finite element model, and by using this model the sensitivities of the springback and the section deformation to process parameters were analyzed and compared. The results show that the most sensitive process conditions for springback angle are the boost speed and the pressure of pressure die, and the most sensitive process condition for section deformation is the number of cores. When the clamp force, the boost speed and the pressure of pressure die are utilized to control section deformation, the effect of these process parameters on springback should be considered. When the process parameters are mainly used to control springback, the effect of these process parameters on the section deformation should be always considered.展开更多
The cyclic rotating−bending(CRB)processes under different deformation conditions were carried out to refine the microstructure and improve the mechanical properties of the 65Cu−35Zn brass tubes.The microstructure and ...The cyclic rotating−bending(CRB)processes under different deformation conditions were carried out to refine the microstructure and improve the mechanical properties of the 65Cu−35Zn brass tubes.The microstructure and the mechanical properties in the axial direction of the tubes after the CRB process were studied with the OM,EBSD and conventional tensile test.To obtain the accumulated effective plastic strain of the tube during the CRB process,the FEM simulation was also executed.The results show that the average grain size decreases with the increase of rotation time at RT,and with the decrease of bending angle at 200℃.With the increase of accumulated effective plastic strain during the CRB process,the reduction rate of average grain size of the brass tube increases,the tensile strength of the brass tube increases in wave shape and the elongation increases first and then sharply decreases.展开更多
Electrochemical impedance spectroscopy (EIS) and electrochemical noise (EN) were used to study the corrosion electrochemical behavior of brass tubes in circulating cooling seawater using the developed sensor. EIS stud...Electrochemical impedance spectroscopy (EIS) and electrochemical noise (EN) were used to study the corrosion electrochemical behavior of brass tubes in circulating cooling seawater using the developed sensor. EIS study shows that the inhibitor can lead to the formation of corrosion products on metal surface, which will then inhibit the corrosion process. When the flow rate of the seawater increases, the diffusion of oxygen speeds up and the action of filming on HAl77-2 tube accelerates, resulting in decrease of corrosion rate. EN analysis shows that the flow rate of the seawater has little effect on pitting susceptivity of HSn70-1 tube; however the pitting susceptivity of HAl77-2 tube increases with increasing flow rate. Good agreement is observed between the spectral noise resistance Rsn (f) calculated from EN data and the modulus of impedance. It is shown that the electrochemical noise technique can be used in corrosion monitoring.展开更多
基金Project (50975235) supported by the National Natural Science Foundation of ChinaProject (B08040) supported by the 111 Project
文摘In order to study the effects of the process parameters on springback and section deformation, a sensitivity analysis model was established based on the combination use of the multi-parameter sensitivity analysis method and the springback/section deformation prediction finite element model, and by using this model the sensitivities of the springback and the section deformation to process parameters were analyzed and compared. The results show that the most sensitive process conditions for springback angle are the boost speed and the pressure of pressure die, and the most sensitive process condition for section deformation is the number of cores. When the clamp force, the boost speed and the pressure of pressure die are utilized to control section deformation, the effect of these process parameters on springback should be considered. When the process parameters are mainly used to control springback, the effect of these process parameters on the section deformation should be always considered.
基金the National Natural Science Foundation of China(No.51304046)the Grant-in-Aid for Young Scientists(B)of Japan Society for the Promotion of Science of Japan(No.25870594)。
文摘The cyclic rotating−bending(CRB)processes under different deformation conditions were carried out to refine the microstructure and improve the mechanical properties of the 65Cu−35Zn brass tubes.The microstructure and the mechanical properties in the axial direction of the tubes after the CRB process were studied with the OM,EBSD and conventional tensile test.To obtain the accumulated effective plastic strain of the tube during the CRB process,the FEM simulation was also executed.The results show that the average grain size decreases with the increase of rotation time at RT,and with the decrease of bending angle at 200℃.With the increase of accumulated effective plastic strain during the CRB process,the reduction rate of average grain size of the brass tube increases,the tensile strength of the brass tube increases in wave shape and the elongation increases first and then sharply decreases.
文摘Electrochemical impedance spectroscopy (EIS) and electrochemical noise (EN) were used to study the corrosion electrochemical behavior of brass tubes in circulating cooling seawater using the developed sensor. EIS study shows that the inhibitor can lead to the formation of corrosion products on metal surface, which will then inhibit the corrosion process. When the flow rate of the seawater increases, the diffusion of oxygen speeds up and the action of filming on HAl77-2 tube accelerates, resulting in decrease of corrosion rate. EN analysis shows that the flow rate of the seawater has little effect on pitting susceptivity of HSn70-1 tube; however the pitting susceptivity of HAl77-2 tube increases with increasing flow rate. Good agreement is observed between the spectral noise resistance Rsn (f) calculated from EN data and the modulus of impedance. It is shown that the electrochemical noise technique can be used in corrosion monitoring.
