Health Risk Assessment of Employees Exposed to Chlorination By-products of Recreational Water in Large Amusement Parks in Shanghai

Objective Chlorination is often used to disinfect recreational water in large amusement parks;however,the health hazards of chlorination disinfection by-products(DBPs)to occupational populations are unknown.This study aimed to assess the exposure status of chlorinated DBPs in recreational water and the health risks to employees of large amusement parks.Methods Exposure parameters of employees of three large amusement parks in Shanghai were investigated using a questionnaire.Seven typical chlorinated DBPs in recreational water and spray samples were quantified by gas chromatography,and the health risks to amusement park employees exposed to chlorinated DBPs were evaluated according to the WHO's risk assessment framework.Results Trichloroacetic acid,dibromochloromethane,bromodichloromethane,and dichloroacetic acid were detected predominantly in recreational water.The carcinogenic and non-carcinogenic risks of the five DBPs did not exceed the risk thresholds.In addition,the carcinogenic and non-carcinogenic risks of mixed exposure to DBPs were within the acceptable risk limits.Conclusion Typical DBPs were widely detected in recreational water collected from three large amusement parks in Shanghai;however,the health risks of DBPs and their mixtures were within acceptable limits.

Effects of Chlorine and Chlorine Monoxide on Stratospheric Ozone Depletion

This paper presents a system approach of mass balance calculations of ozone and other species under diffusion-convection-reaction processes to study the impacts of major ozone-depleting chemicals, chlorine (Cl) and chlorine monoxide (ClO), and the effect of photolysis on ozone concentrations, ozone depletion, total ozone abundance, and ozone layer along the altitude in the stratosphere. The calculated ozone concentrations and profile of the layer followed a similar trend and were generally in good agreement with the measurements above the tropical area. The calculated peak of the layer was at the same mid-stratosphere at Z = 30 km with a peak concentration and total ozone abundance about 20% higher than the measured peak concentration of 8.0 ppm and total abundance of 399 DU. In the presence of Cl and ClO, the calculated ozone concentrations and total abundance were substantially reduced. Cl generally depleted more uniformly of ozone across the altitude, while ClO reduced substantially the ozone in the upper stratosphere and thus shifted the peak of the layer to a much lower elevation at Z = 14 km. Although both ClO and Cl are active ozone-depleting chemicals, ClO was found to have a more pronounced impact on ozone depletion and distribution than Cl. The possible explanations of these interesting phenomena were discussed and elaborated. The approach and calculations in this paper were shown to be useful in providing an initial insight into the structure and behavior of the complex ozone layer.

Unveiling the geometric site dependent activity of spinel Co_(3)O_(4)for electrocatalytic chlorine evolution reaction

Spinel cobalt oxide(Co_(3)O_(4)),consisting of tetrahedral Co^(2+)(CoTd)and octahedral Co^(3+)(CoOh),is considered as promising earth-abundant electrocatalyst for chlorine evolution reaction(CER).Identifying the catalytic contribution of geometric Co site in the electrocatalytic CER plays a pivotal role to precisely modulate electronic configuration of active Co sites to boost CER.Herein,combining density functional theory calculations and experiment results assisted with operando analysis,we found that the Co_(Oh) site acts as the main active site for CER in spinel Co_(3)O_(4),which shows better Cl^(-)adsorption and more moderate intermediate adsorption toward CER than CoTd site,and does not undergo redox transition under CER condition at applied potentials.Guided by above findings,the oxygen vacancies were further introduced into the Co_(3)O_(4) to precisely manipulate the electronic configuration of Co_(Oh) to boost Cl^(-)adsorption and optimize the reaction path of CER and thus to enhance the intrinsic CER activity significantly.Our work figures out the importance of geometric configuration dependent CER activity,shedding light on the rational design of advanced electrocatalysts from geometric configuration optimization at the atomic level.

Molecular packing tuning via chlorinated end group enables efficient binary organic solar cells over 18.5%

Designing novel nonfullerene acceptors(NFAs)is of vital importance for the development of organic solar cells(OSC).Modification on the side chain and end group are two powerful tools to construct efficient NFAs.Here,based on the high-performance L8BO,we selected 3-ethylheptyl to substitute the inner chain of 2-ethylhexyl,obtaining the backbone of BON3.Then we introduced different halogen atoms of fluorine and chlorine on 2-(3-oxo-2,3-dihydro-1Hinden-1-ylidene)malononitrile end group(EG)to construct efficient NFAs named BON3-F and BON3-Cl,respectively.Polymer donor D18 was chosen to combine with two novel NFAs to construct OSC devices.Impressively,D18:BON3-Cl-based device shows a remarkable power conversion efficiency(PCE)of 18.57%,with a high open-circuit voltage(V_(OC))of 0.907 V and an excellent fill factor(FF)of 80.44%,which is one of the highest binary PCE of devices based on D18 as the donor.However,BON3-F-based device shows a relatively lower PCE of 17.79%with a decreased FF of 79.05%.The better photovoltaic performance is mainly attributed to the red-shifted absorption,higher electron and hole mobilities,reduced charge recombination,and enhanced molecular packing in the D18:BON3-Cl films.Also,we performed stability tests on two binary systems;the D18:BON3-Cl and D18:BON3-F devices maintain 88.1%and 85.5%of their initial efficiencies after 169 h of storage at 85°C in an N2-filled glove box,respectively.Our work demonstrates the importance of selecting halogen atoms on EG and provides an efficient binary system of D18:BON3-Cl for further improvement of PCE.

The Toxic Effects of Strong Chlorin Disinfectant on Mangroves and Emission Thresholds

In this study, based on the simulated discharge results of chemical disinfectants, hypocotyl germination concentration gradient pre-test and concentration gradient determination experiment were set up respectively. Laboratory cultivation was conducted to compare and analyze the root germination and germination indexes, three mangrove hypocotyls of Kandelia candel (Linn.) Druce, Ceriopstagal C.B. Rob. and Bruguiera sexangula var. Rhynchopetalas’ efficiency of cumulative root germination, cumulative germination and the cumulative expansion of the second pair of leaves, one-way analysis of variance was used to obtain the tolerance threshold of three mangrove hypocotyls to strong chlorin disinfectant. The study determined that the by-products of strong chlorin disinfectant, the toxic threshold concentrations of Kandelia candel (Linn.) Druce, Ceriopstagal C.B. Rob. and Bruguiera sexangula var. rhynchopetala are close to 0.55 mg/L, 0.55 mg/L and 0.25 mg/L, respectively. This concentration range is lower than the average concentration of 1.183 mg/L of active chlorine emitted from strong chlorine concentrate during pond clearing in high-level shrimp ponds, indicating that transient emissions of strong chlorine concentrate during pond clearing can have a toxic effect on mangrove plants. The strength of tolerance of the embryonic axes of the three mangrove species to effective chlorine contamination was, Ceriopstagal C.B. Rob. stronger than Bruguiera sexangula var. rhynchopetala, and Kandelia candel (Linn.) Druce is the weakest.

Chlorine-Substituent Regulation in Dopant-Free Small-Molecule Hole-Transport Materials Improves the Effi ciency and Stability of Inverted Perovskite Solar Cells

Although doped hole-transport materials(HTMs)off er an effi ciency benefi t for perovskite solar cells(PSCs),they inevi-tably diminish the stability.Here,we describe the use of various chlorinated small molecules,specifi cally fl uorenone-triphenylamine(FO-TPA)-x-Cl[x=para,meta,and ortho(p,m,and o)],with diff erent chlorine-substituent positions,as dopant-free HTMs for PSCs.These chlorinated molecules feature a symmetrical donor-acceptor-donor structure and ideal intramolecular charge transfer properties,allowing for self-doping and the establishment of built-in potentials for improving charge extraction.Highly effi cient hole-transfer interfaces are constructed between perovskites and these HTMs by strategi-cally modifying the chlorine substitution.Thus,the chlorinated HTM-derived inverted PSCs exhibited superior effi ciencies and air stabilities.Importantly,the dopant-free HTM FO-TPA-o-Cl not only attains a power conversion effi ciency of 20.82% but also demonstrates exceptional stability,retaining 93.8%of its initial effi ciency even after a 30-day aging test conducted under ambient air conditions in PSCs without encapsulation.These fi ndings underscore the critical role of chlorine-substituent regulation in HTMs in ensuring the formation and maintenance of effi cient and stable PSCs.

Effects of surface chlorine atoms on charge distribution and reaction barriers for photocatalytic CO_(2)reduction

Photocatalytic CO_(2)reduction to produce high value-added carbon-based fuel has been proposed as a promising approach to mitigate global warming issues.However,the conversion efficiency and product selectivity are still low due to the sluggish dynamics of transfer processes involved in proton-assisted multi-electron reactions.Lowering the formation energy barriers of intermediate products is an effective method to enhance the selectivity and productivity of final products.In this study,we aim to regulate the surface electronic structure of Bi_(2)WO_(6)by doping surface chlorine atoms to achieve effective photocatalytic CO_(2)reduction.Surface Cl atoms can enhance the absorption ability of light,affect its energy band structure and promote charge separation.Combined with DFT calculations,it is revealed that surface Cl atoms can not only change the surface charge distribution which affects the competitive adsorption of H_(2)O and CO_(2),but also lower the formation energy barrier of intermediate products to generate more intermediate*COOH,thus facilitating CO production.Overall,this study demonstrates a promising surface halogenation strategy to enhance the photocatalytic CO_(2)reduction activity of a layered structure Bi-based catalyst.

Calculations and Sensitivity Analysis of Chlorine-,NO_(x)-,and Bromine-Depleting Cycles of Stratospheric Ozone

This paper presents an engineering system approach using a 2D model of conservation of mass to study the dynamics of ozone and concerned chemical species in the stratosphere.By considering all fourteen photolysis,ozone-generating,and-depleting chemical reactions,the model calculated the transient,spatial changes of ozone under different physical-chemical-radiative conditions.Validation against the measured data demonstrated good accuracy,close match of our model with the observed ozone concentrations at both 20°S and 90°N locations.The deviation in the average concentration was less than 1% and in ozone profiles less than 17%.The impacts of various chlorine-(Cl),nitrogen oxides-(NO_(x)),and bromine-(Br)depleting cycles on ozone concentrations and distribution were investigated.The chlorine catalytic depleting cycle was found to exhibit the most significant impact on ozone dynamics,confirming the key role of chlorine in the problem of ozone depletion.Sensitivity analysis was conducted with levels of 25%,50%,100%,200%,and 400% of the baseline value.The combined cycles(Cl+NO_(x)+Br)showed the most significant influence on ozone behavior.The total ozone abundance above the South Pole could decrease by a small 3%,from 281 DU(Dubson Units)to 273 DU for the 25% level,or by a huge thinning of 60%to 114 DU for the 400% concentration level.When the level of chlorine gases increased beyond 200%,it would cause ozone depletion to a level of ozone hole(below 220 DU).The 2D Ozone Model presented in this paper demonstrates robustness,convenience,efficiency,and executability for analyzing complex ozone phenomena in the stratosphere.

Extraction of lithium from lepidolite using chlorination roasting-water leaching process

Chlorination roasting followed by water leaching process was used to extract lithium from lepidolite.The microstructure of the lepidolite and roasted materials were characterized by X-ray diffraction（XRD）.Various parameters including chlorination roasting temperature,time,type and amount of chlorinating agents were optimized.The conditional experiments indicate that the best mass ratio of lepidolite to NaCl to CaCl2 is 1：0.6：0.4 during the roasting process.The extraction of lithium reaches peak value of 92.86% at 880 °C,potassium,rubidium,and cesium 88.49%,93.60% and 93.01%,respectively.The XRD result indicates that the major phases of the product after roasting lepidolite with mixture of chlorinating agents（CaCl2 and NaCl） are SiO2,CaF2,KCl,CaSiO3,CaAl2Si2O8,NaCl and NaAlSi3O8.

Behavior of titanium dioxide in alumina carbothermic reduction-chlorination process in vacuum

Behaviors of TiO2 in the alumina carbothermic reduction and chlorination process in vacuum at different temperatures were investigated experimentally by means of XRD,SEM and EDS.In the preparation of materials,the molar ratio of Al2O3 to C was 1：4,and 10% TiO2 and excess AlCl3 were added.The results show that TiC is produced by C and TiO2 after TiO2 transforms from anatase into rutile gradually.In the temperature range of 1 763？1 783 K,the compounds of Ti and Al are not found in slags and condensate.The purity of aluminum reaches 98.35%,and TiO2 does not participate in alumina carbothermic reduction process and chlorination process in vacuum.

Bromate ion formation in dark chlorination and ultraviolet/chlorination processes for bromide-containing water

Bormate （BrO3^-） is a carcinogenic chemical produced in ozonation or chlorination of bromide-containing water. Although its formation in seawater with or without sunlight has been previously investigated, the formation of bromate in dilute solutions, particularly raw water for water treatment plant, is unknown. In this article, the results of bench scale tests to measure the formation rates of bromate formation in dilute solutions, including de-ionized water and raw water from Yangtze River, were presented in dark chlorination and ultraviolet （UV）/chlorination processes. And the effects of initial pH, initial concentration of NaOCl, and UV light intensity on bromate formation in UV/chlorination of the diluted solutions were investigated. Detectable bromate was formed in dark chlorination of the two water samples with a relatively slow production rate. Under routine disinfecting conditions, the amount of formed bromate is not likely to exceed the national standards （10 μg/L）. UV irradiation enhanced the decay of free chlorine, and, simultaneously, 6.6%-32% of Br^- was oxidized to BrO3^-. And the formation of bromate exhibited three stages： rapid stage, slow stage and plateau. Under the experimental conditions （pH = 4.41-11.07, CCl2= 1.23-4.50 mg/L）, low pH and high chlorine concentration favored the generation of bromate. High light intensity promoted the production rate of bromate, but decreased its total generation amount due to acceleration of chlorine decomposition.

Tomato Yield and Quality and Emitter Clogging as Affected by Chlorination Schemes of Drip Irrigation Systems Applying Sewage Effluent

Chlorination has been recognized as an efficient and economically favorable method for treating clogging in drip emitters caused by biological growth during sewage application. Further important criteria for determining an optimal chlorination scheme are the different responses of crops to the chloride added into the soil through chlorination. During two seasons in 2008 and 2009, field experiments were conducted in a solar-heated greenhouse with drip irrigation systems applying secondary sewage effluent to tomato plants to investigate the influences of chlorine injection intervals and levels on plant growth, yield, fruit quality, and emitter clogging. Injection intervals ranging from 2 to 8 wk and injection concentrations ranging 2-50 mg L-1 of free chlorine residual at the end of the laterals were used. For the 2008 experiments, the yield from the treatments of sewage application with chlorination was 7.5% lower than the yield from the treatment of sewage application without chlorination, while the yields for the treatments with and without chlorination were similar for the 2009 experiments. The statistical tests indicated that neither the chlorine injection intervals and concentrations nor the interactions between the two significantly influenced plant height, leaf area, or tomato yield for both years. The qualities of the fruit in response to chlorination were parameter-dependent. Chlorination did not significantly influence the quality of ascorbic acid, soluble sugar, or soluble acids, but the interaction between the chlorine injection interval and the chlorine concentration significantly influenced the levels of soluble solids. It was also confirmed that chlorination was an effective method for reducing biological clogging. These results suggested that chlorination is safe for a crop that has a moderate sensitivity to chlorine, like tomato, and can maintain a high level of performance in drip irrigation systems applying sewage effluent.

Utilization of gold-bearing and iron-rich pyrite cinder via a chlorination–volatilization process

The chlorination-volatilization process has been adopted to make full use of gold-bearing and iron-rich pyrite cinder. However, problems of low recovery rate, pulverization of pellets, and ring formation have been encountered during the industrialization of this process. The effects of various parameters on the volatilization rates of valuable metals and on the compressive strength of roasted pellets were investigated in this paper. The parameters include the CaCl_2 dosage, heating temperature, and holding time. The results show that heating temperature is the most important parameter for the recovery of target metals. More CaCl_2 was needed for the recovery of zinc than for the recovery of gold, silver, and lead. CaCl_2 started to react with sulfides/SO_2/SiO_2 at temperatures below the melting point of CaCl_2 to generate Cl_2/HCl. Gaseous CaCl_2 was formed at higher temperatures and could react with any of the components. The compressive strength of roasted CaCl_2-bearing pellets first decreased slowly with increasing temperature at temperatures lower than 873 K, which could result in the pulverization of pellets during heating. Their compressive strength increased dramatically with increasing temperature at temperatures greater than 1273 K. Certain quantities of CaCl_2 and Fe(Ⅱ) could improve the compressive strength of the roasted pellets; however, the addition of excessive CaCl_2 decreased the compressive strength of pellets.

Preparation of Novel Dechlorination Adsorbent and Study on Its Adsorption Mechanism

The preparation of novel dechlorination adsorbent by using the modified 13 X molecular sieve and its adsorption mechanism were studied. XRD and SEM analyses showed that the Ag-13 X molecular sieve revealed a new crystal plane,while other molecular sieve samples more or less contained some impurities. The BET data showed that only Ag^+ ions could enlarge the pore size and the pore volume at the same time. The NH_3-TPD diagram showed that the acid sites of the adsorbent increased after its modification by metal ions and only the Ag-13 X molecular sieve generated new medium strong acid sites. According to adsorption experiments conducted at different concentration and temperature, the dechlorination adsorption mechanism of Ag-13 X molecular sieve was a combination of physical adsorption and chemical adsorption which showed the different degree of influence at different temperatures.

Extraction of metals from complex sulfide nickel concentrates by low-temperature chlorination roasting and water leaching

The recovery of valuable metals from complex sulfide concentrates was investigated via chlorination roasting followed by water leaching. A reaction process is proposed on the basis of previous studies and the results of our preliminary experiments. During the process, various process parameters were studied, including the roasting temperature, the addition of NH4Cl, the roasting time, the leaching time, and the liquid-to-solid ratio. The roasted products and leach residues were characterized by X-ray diffraction and vibrational spectroscopy. Under the optimum condition, 95% of Ni, 98% of Cu, and 88% of Co were recovered. In addition, the removal of iron was studied in the water leaching stage. The results demonstrate that this process provides an effective approach for extracting multiple metals from complex concentrates or ores. © 2017, University of Science and Technology Beijing and Springer-Verlag Berlin Heidelberg.

Simultaneous Control of Microorganisms and Disinfection By-products by Sequential Chlorination

Objective To introduce a new sequential chlorination disinfection process in which short-term free chlorine and chloramine are sequentially added. Methods Pilot tests of this sequential chlorination were carried out in a drinking water plant. Results The sequential chlorination disinfection process had the same or better efficiency on microbe （including virus） inactivation compared with the free chlorine disinfection process. There seemed to be some synergetic disinfection effect between free chlorine and monochloramine because they attacked different targets. The sequential chlorination disinfection process resulted in 35.7%-77.0% TTHM formation and 36.6%-54.8% THAA5 formation less than the free chlorination process. The poorer the water quality was, the more advantage the sequential chlorination disinfection had over the free chlorination. Conclusion This process takes advantages of free chlorine＇s quick inactivation of microorganisms and chloramine＇s low disinfection by-product （DBP） yield and long-term residual effect, allowing simultaneous control of microbes and DBPs in an effective and economic way.

Recovering germanium from coal ash by chlorination with ammonium chloride

A new process of enriching germanium from coal ash was developed. The processinvolves in mixing the coal ash and ammonium chloride and then roasting the mixture to producegermanium chloride that is then absorbed by dilute hydrochloric acid and hydrolyzed to germaniumoxide. The germanium recovery reached to 80.2% at the optimum condition: mass ratio of NH_4Cl/coalash is 0.15, roasting temperature 400℃ and roasting time 90 min.

Chlorination strategy on polymer donors toward efficient solar conversions

Bulk heterojunction(BHJ)polymer solar cells(PSCs)are promising candidates for next-generation solar cells.Benefitting from the persistent efforts in material design and synthesis,systematic device engineering and fundamental understanding of the device physics,the power conversion efficiency(PCE)of single PSC has been pushed to surpass 15%,and that of the tandem PSCs is over 17%.Recently,chlorination has drawn much interest and the chlorinated PSCs have been frequently reported in donor-acceptor(D-A)type conjugated polymers.This review summarizes the recent progress of the chlorinated strategy for highly efficient photovoltaic applications.We firstly discuss the chlorination on the acceptor units in D-A type donor polymers,emphasizing the 4 widely used acceptor units with their improved PCE.secondly,the chlorination on the donor units will be discussed,mainly focusing on the chlorination of benzo[1,2-b:4,b]dithiophene(BDT)unit and 2,2-bithiophene unit.Remarkably,the PCE of the chlorinated BDT-based device has been improved to over 14%.Overall,this review discusses the structure-property correlations of these chlorinated polymers in photovoltaic study,which could further provide guidance on the chlorinated strategy and the molecular design for high-performance photovoltaic devices.

Researches on Formation of Haloacetic Acids in Chlorination of Drinking Water by a Novel Technique

Haloacetic acids(HAAs) are formed during the chlorination of drinking water,which are harmful to people′s health due to their carcinogenic and mutagenic effects. In the present study,a detection method combining methyl tert -butyl ether(MtBE) extraction with acid catalysis and gas chromatography coupled with an electron capture detector(GC/ECD) was developed for determining HAAs. The detection limit of this method(MDL) and relative standard deviation(RSD) were below 0.37 μg/L and 6.2%,respectively. The laboratory chlorination experiments were conducted with the purpose of investigating the influences of reaction time,temperature,UV_ 254 ,bromide and ammonia-nitrogen on the formation of HAAs. The results show that the formation amount of HAAs increases with increasing reaction time and temperature,respectively;and there exists a linear relationship between the formation of HAAs and UV_ 254 . The formation amount of HAAs decreases first and then increases as the bromide ion concentration increases,and adding NH +_4 is a possible way to control the formation of HAAs.

Kinetics of leaching refractory gold ores by ultrasonic-assisted electro-chlorination

The resources of refractory gold ores are abundant, and their effective treatment can bring good economic benefits. This paper investigated the kinetics of leaching gold from refractory gold ores by ultrasonic-assisted electro-chlorination. The effects of ultrasound time ratio, initial hydrochloric acid concentration and leaching temperature on the kinetic parameters were discussed. It is found that the leaching ratio goes up with all the factors increasing. The reaction kinetics is controlled by diffusion. When ultrasound improves the diffusion by reducing the diffusion resistance, the activation energy increases to 37.1 kJ/mol.