Turbocharger Noise Prediction Using Broadband Noise Source Model

The noise prediction of the turbocharger is studied.The broadband noise source model is employed to predict the near-field noise of the turbocharger.The 3D software Solidworks is adopted to establish the model blades and inlet of turbocharger compressor,then this 3D model is introduced into the software CFD to calculate the flow-field under different inlet shapes,different blades shapes and different clearances between casing and impeller.On the base of the above simulation,the broadband noise source model is employed to calculate and analyze the near-field noise.The calculation shows that compressor static pressure values and the sound power values near the impeller outlet are the largest.Through the noise calculation by using broadband noise source model under different inlet shapes and blade shapes,we find that the noise level of the inlet of cylindrical and cone types are smaller.Compared with the current widespread used backward skewed or radial blades,there is little difference of the noise value of the inlet of the forward skewed blades.

Numerical analysis of broadband noise reduction with wavy leading edge

Large Eddy Simulation（LES） is performed to investigate the airfoil broadband noise reduction with wavy leading edge under anisotropic incoming turbulence. The anisotropic incoming turbulence is generated by a rod with a diameter of 10 mm. The incoming flow velocity is 40 m/s and the corresponding Reynolds numbers based on airfoil chord and rod diameter are about 397000 and 26000, respectively. The far-field acoustic field is predicted using an acoustic analogy method which has been validated by the experiment. A straight leading edge airfoil and a wavy leading edge airfoil are simulated. The results show that wavy leading edge increases the airfoil lift and drag whereas the lift and drag fluctuations are substantially reduced. In addition, wavy leading edge can significantly change the flow pattern around the leading edge and a pair of counter-rotating streamwise vortices stemming from each wavy leading edge peak are observed.An averaged noise reduction of 9.5 dB is observed with the wavy leading edge at the azimuthal angle of 90°. Moreover, the wavy leading edge can mitigate noise radiation at all the azimuthal angles without significantly changing the noise directivity. The underlying noise reduction mechanisms are then analyzed in detail.

Investigation of rotor–stator interaction broadband noise using a RANS-informed analytical method

A Reynolds-Averaged Navier Stokes(RANS)-information analytical method for predicting Rotor-Stator Interaction(RSI)broadband noise is established in this paper.First,the turbulence information is deduced from RANS simulation result.Then,the unsteady load on the stator blade is calculated using a strip theory approach based on LINearized SUBsonic unsteady flow in cascade(LINSUB)and 2-D equivalence method.In the end,the sound power of RSI broadband noise is calculated by coupling the unsteady load on the stator blade with acoustic analogy and annular duct mode.The broadband noise model part of the RANS-information analytical method is validated against the upstream sound power of an annular cascade experimental bench.Besides,the RANS-information analytical method is used in predicting RSI broadband noise of a single-stage axial fan acoustic experimental bench,the results illustrate that the RANS-information analytical method can accurately predict the RSI broadband noise in different fan working conditions.After simplification the Wave Leading Edge(WLE)stator blade,the effect of WLE stator blade on RSI broadband noise is studies.Although the simplification may bring some discrepancies,the results illustrate that the RANS-information analytical method has the capability for further studies on the broadband noise reduction with WLE stator blade.

Numerical Study on the Duct Noise Control of Single-Stage Axial Flow Fan with Wave Leading Edge Stator Blade Configurations

This study focuses on a single-stage axial flow fan, investigating the effect of three kinds of wave leading edge stator blades on its noise reduction. The DDES method and the duct acoustic analogy theory based on the penetrable data surface were used for noise prediction. The results showed that the three kinds of wave leading edge blades were effective in reducing the rotor-stator interaction tonal noise and also have a certain inhibitory effect on broadband noise. The A10W15 stator blade can effectively reduce broadband noise in the frequency range of 2200 - 4200 Hz. When the amplitude is increased to 20, the noise reduction effect is further enhanced. However, when the amplitude is increased to 30, the broadband noise reduction effect is no longer significant. Further research shows that the wave leading edge stator blades can significantly change the pressure fluctuation distribution on the leading edge and suction surface, which control the modal energy distribution. Finally, this paper analyzed multiple factors affecting the broadband noise reduction, such as the noise source cut-off and cut-on effect and correlation. The purpose of this paper is to explore the laws of the influence of wave leading edge blades on the duct noise of real fan, and to reveal its noise control mechanism. .

The noise spectral characteristics and noise reduction schemes of screw air-source heat pump:A case study

The screw air-source heat pump can cause incessant high noise levels during operation,which might hinder adoption of this energy-efficient heat pump.First,acoustic measurements and comparison testing were performed in this research.The measurements revealed that the compressor is the main noise source of the heat pump,and it shows a multipeak frequency distribution and a wide frequency spectrum under different work conditions,with multiple peaks at 63,250,and 1000 Hz.Then,a compressor sound insulation cover with broadband absorption was proposed,and it was experimentally proven that the insulation cover can reduce the maximum sound pressure level of one unit from 89.8 dBA to 79.1 dBA.Third,we proposed several noise reduction strategies and compared their noise reduction effects using computer simulation.The results showed that the noise problem can be effectively improved through the rational design of the sound barrier and the layout and opening options of heat pump.The distance between the sound barrier and heat pump and the sound attenuation due to diffraction ALa exhibit a U-shaped relation.For buildings of different heights,the optimal heights of noise barrier are proposed.The 5.5-meter is the optimal height of the sound barrier for single-story buildings.The conclusions can be applied to other building projects for heat pump noise reduction.

BROADBAND ROTOR NOISE PREDICTION BASED ON A NEW FREQUENCY-DOMAIN FOUMULATION

This article studies the broadband noise of a rotor in upstream turbulence. A numerical approach is proposed, based on frequency domain, for predicting rotor broadband noise which requires the aerodynamic sources to be integrated over the actual blade surface rather than over the mean-chord surface. The prediction of the radiated rotor broadband noise due to turbulence is made This method is validated through a comparison between numerical predictions and measured data, with a reasonable agreement. Noise level directivity shows that the main lobe is located along the rotor axis, while the minimum noise occurs in the direction vertical to the rotor axis.