Dynamic analysis of buried pipeline with and without barrier system subjected to underground detonation

Failure of pipe networks due to blast loads resulting from terrorist attacks or construction facilities, may cause economic loss, environmental pollution, source of firing or even it may lead to a disaster. The present work develops a closed-form solution of buried pipe with barrier system subjected to subsurface detonation. The solution is derived based on the concept of double-beam system. Euler Bernoulli's beams are used to simulate the buried pipe and the barrier system. Soil is idealized as viscoelastic foundation along with shear interaction between discrete Winkler springs(advanced soil model). The finite SineFourier transform is employed to solve the coupled partial differential equations. The solution is validated with past studies. A parametric study is conducted to investigate the influence of TNT charge weight, pipe material, damping ratio and TNT offset on the response of buried pipe with and without barrier system. Further a statistical analysis is carried out to get the significant soil and pipe input parameters. It is perceived that peak pipe displacements for both the cases(with and without barrier) are increases with increasing the weight of TNT charge and decreases with increasing the damping ratio and TNT offset. The deformation of pipe also varies with pipe material. Pipe safety against blast loads can be ensured by providing suitable barrier layer. The present study can be utilized in preliminary design stage as an alternative to expensive numerical analysis or field study.

An electrochemical method for evaluating the resistance to cathodic disbondment of anti-corrosion coatings on buried pipelines

Methods for evaluating the resistance to cathodic disbondment （RCD） of anti-corrosion coatings on buried pipelines were reviewed. It is obvious that these traditional cathodic disbondment tests （CDT） have some disadvantages and the evaluated results are only simple figures and always rely on the subjective experience of the operator. A new electrochemical method for evaluating the RCD of coatings, that is, the potentiostatic evaluation method （PEM）, was developed and studied. During potentiostatic anodic polarization testing, the changes of stable polarization current of specimens before and after cathodic disbonding （CD） were measured, and the degree of cathodic disbondment of the coating was quantitatively evaluated, among which the equivalent cathodic disbonded distance AD was suggested as a parameter for evaluating the RCD. A series of testing parameters of the PEM were determined in these experiments.

Response analysis of buried pipelines crossing fault due to overlying soil rupture

A 3-D soil-pipe nonlinear finite element model with contact element is suggested and the influences of the rupture mode, thickness and rigidity of overlying soil on the response of buried pipeline are analyzed. The numerical results show that the soil rupture mode determines the location of the large deformation or failure of the pipeline, and the plastic de- formation of the pipeline occurs at the zone where the plastic deformation or rupture of the overlying soil appears. When the fault dip angle on bedrock is near 90°, two plastic deformation sections of the pipeline appear with the development of overlying soil rupture. And the thicker the overlying soil is, the longer the plastic deformation length of the pipeline is and the less its strain is. The plastic deformation length of the pipeline decreases while its maximum strain increases with the rigidity of overlying soil increasing.

Undersea Buried Pipeline Reconstruction Based on the Level Set and Inverse Multiquadric Regularization Method

The electric inversion technique reconstructs the subsurface medium distribution from acquired data.On the basis of electric inversion,objects buried under the earth or seabed,such as pipelines and unexploded ordnance,are detected and located in a contactless manner.However,the process of accurately reconstructing the shape of the target object is challenging because electric inversion is a nonlinear and ill-posed problem.In this work,we present an inverse multiquadric(IMQ)regularization method based on the level set function for reconstructing buried pipelines.In the case of locating underwater objects,the unknown inversion area is split into two parts,the background and the pipeline with known conductivity.The geometry of the pipeline is represented based on the level set function for achieving a noiseless inversion image.To obtain a binary image,the IMQ is used as the regularization term,which‘pushes’the level set function away from 0.We also provide an appropriate method to select the bandwidth and regularization parameters for the IMQ regularization term,resulting in reconstructed images with sharp edges.The simulation results and analysis show that the proposed method performs better than classical inversion methods.

Finite Element Structural Analysis of Buried Pipelines

This document uses previous results (which we call the first stage), for the development of a computer model based on finite elements under the FEAP programmer, to carry out a structural analysis of a pipeline. For this purpose, we used environmental variables that we believe influence the failure of buried pipelines such as the internal pressure of fluid, the type of support used, the temperature at which the pipelines work, the type of soil and the stiffness of the soil acting on it. Once the model was finalized, analyses were made with each of the variables separately and combined to observe the behavior of the pipeline, finding the most unfavorable case that indicates the main causes that led to its failure.

The Analysis and Comparison of All Kinds of Buried Pipeline Model Based on Seismic Effect

The problem of seismic response of buried pipeline aimed at the interaction of soil around the pipeline and the complicated calculation model was considered, and the various simplified finite element model was calculated, and it was analyzed. Firstly, the ADINA finite element analysis software was used. The four nodes in shell unit were used by tube. The spring unit was used by soil spring. The analysis model of buried pipeline finite element numerical based on tension and compression spring was established. Seismic wave was input. The response to the simple boundary, viscoelastic boundary earthquake were calculated and analyzed by the finite element numerical simulation. The pipeline’s earthquake ground motion response was obtained, and was compared with the real soil model, and the most suitable simplified calculation model for numerical analysis of buried pipeline was found, which was the numerical analysis model of buried pipeline pressure spring tension finite element based on the viscoelastic boundary, and the theory basis for the seismic design of pipeline was provided.

Prediction of vertical displacement for a buried pipeline subjected to normal fault using a hybrid FEM-ANN approach

Fault movement during earthquakes is a geotechnical phenomenon threatening buried pipelines and with the potential to cause severe damage to critical infrastructures.Therefore,effective prediction of pipe displacement is crucial for preventive management strategies.This study aims to develop a fast,hybrid model for predicting vertical displacement of pipe networks when they experience faulting.In this study,the complex behavior of soil and a buried pipeline system subjected to a normal fault is analyzed by using an artificial neural network(ANN)to generate predictions the behavior of the soil when different parameters of it are changed.For this purpose,a finite element model is developed for a pipeline subjected to normal fault displacements.The data bank used for training the ANN includes all the critical soil parameters(cohesion,internal friction angle,Young’s modulus,and faulting).Furthermore,a mathematical formula is presented,based on biases and weights of the ANN model.Experimental results show that the maximum error of the presented formula is 2.03%,which makes the proposed technique efficiently predict the vertical displacement of buried pipelines and hence,helps to optimize the upcoming pipeline projects.

Natural aging mechanism of buried polyethylene pipelines during long-term service

Currently,accelerated aging tests are widely used to study the aging process of polyethylene pipelines.However,this approach can only simulate one or several main influencing factors in the natural environment,which are often quite different from the actual environment of the buried pipelines.In this study,five types of PE80 buried pipelines in service for 9e18 years were taken as the research object,while new PE80 pipelines were taken as the reference group.The aging process and mechanism of polyethylene buried pipelines were studied through mechanical and chemical property tests and microstructural analysis.The results showed that the pipeline exhibited cross-linking as the main aging mechanism after being in service for 0e18 years.The aging degree and law of the inner and outer surface of the pipeline were compared,and the observed mechanism of both surfaces was explained.After 18 years in service,the elongation at the break of the pipe decreased by 16.2%,and the toughness of the matrix in the main collapse area of the tensile sample was the fundamental reason responsible for changes in the mechanical properties.Finally,after 18 years in service,the oxidation induction time of the pipeline was 25.7 min,which was 28.5% higher than the national standard value.There were no potential safety hazards during continuous long-term service.The results of this paper provide reference data and theoretical guidance for the aging process study of buried polyethylene pipelines.

Centrifuge modeling of buried continuous pipelines subjected to normal faulting

Seismic ground faulting is the greatest hazard for continuous buried pipelines.Over the years,researchers have attempted to understand pipeline behavior mostly via numerical modeling such as the finite element method.The lack of well-documented field case histories of pipeline failure from seismic ground faulting and the cost and complicated facilities needed for full-scale experimental simulation mean that a centrifuge-based method to determine the behavior of pipelines subjected to faulting is best to verify numerical approaches.This paper presents results from three centrifuge tests designed to investigate continuous buried steel pipeline behavior subjected to normal faulting.The experimental setup and procedure are described and the recorded axial and bending strains induced in a pipeline are presented and compared to those obtained via analytical methods.The influence of factors such as faulting offset,burial depth and pipe diameter on the axial and bending strains of pipes and on ground soil failure and pipeline deformation patterns are also investigated.Finally,the tensile rupture of a pipeline due to normal faulting is investigated.

Engineering measures for preventing upheaval buckling of buried submarine pipelines

In-service hydrocarbons must be transported at high temperature and high pressure to ease the flow and to prevent the solidification of the wax fraction. The high temperature and high pressure will induce the additional stress in the pipeline, which results in the upheaval buckling of the pipeline. If such expansion is resisted, e.g., by the frictional effects of the foundation soil over a kilometer or of a pipeline, the compressive axial stress will be set up in the pipe-wall. When the stress exceeds the constraint of the foundation soil on the pipeline, suddenly-deforming will occur to release the internal stress, similar to the sudden deformation of the strut due to stability problems. The upheaval buckling may jeopardize the structural integrity of the pipeline. Therefore, effective engineering measures against this phenomenon play an important role in the submarine pipeline design. In terms of the pipeline installation and protection measures commonly used in Bohai Gulf, three engineering measures are investigated in great details. An analytical method is introduced and developed to consider the protection effect of the anti-upheaval buckling of the pipeline. The analysis results show that the amplitude of the initial imperfection has a great effect on the pipeline thermal upheaval buckling. Both trenching and burial and discrete dumping are effective techniques in preventing the pipeline from buckling. The initial imperfection and operation conditions of the pipelines determine the covered depth and the number of layers of the protection measures.

Analytical method for the mechanical response of buried pipeline under the action of strike-slip faulting

Buried pipelines are commonly damaged when laid across strike-slip faults,always leading to some level of destruction with fault movement.The moment of the neutral axis of a pipe section was obtained by integration,and the equations for the bending moment and the bending strain on a pipeline’s section were presented here,based on a trilinear stress–strain model.The calculation method for the lateral soil pressure and pipeline’s bending strain near the fault-crossing point was improved.Lateral soil pressure was regarded as being related to lateral pipeline movement and,for accurate calculation,this part of the pipeline was divided into finite element segments.An iterative process for solving for pipe bending strain was derived,and the algorithm and program for calculating bending strain and the potential damage position of the pipeline’s sections was compiled based on Matlab software.Compared with finite element method(FEM)results and the current standard method,in the situation of a pipeline being in tension under the action of a strike-slip fault(intersection angle<90),the result of the proposed method is in good agreement with FEM results.This shows that the proposed analytical method possessed a good reference value for the strain response analysis of tensile steel pipelines under strike-slip faulting.

Stress analysis on large-diameter buried gas pipelines under catastrophic landslides

This paper presents a method for analysis of stress and strain of gas pipelines under the effect of horizontal catastrophic landslides. A soil spring model was used to analyze the nonlinear characteristics concerning the mutual effects between the pipeline and the soil. The Ramberg–Osgood model was used to describe the constitutive relations of pipeline materials. This paper also constructed a finite element analysis model using ABAQUS finite element software and studied the distribution of the maximum stress and strain of the pipeline and the axial stress and strain along the pipeline by referencing some typical accident cases. The calculation results indicated that the maximum stress and strain increased gradually with the displacement of landslide.The limit values of pipeline axial stress strain appeared at the junction of the landslide area and non-landslide area. The stress failure criterion was relatively more conservative than the strain failure criterion. The research results of this paper may be used as a technical reference concerning the design and safety management of large-diameter gas pipelines under the effects of catastrophic landslides.

Study on the Economic Insulation Thickness of the Buried Hot Oil Pipelines Based on Environment Factors

It is important to determine the insulation thickness in the design of the buried hot oil pipelines.The economic thickness of the insulation layer not only meets the needs of the project but also maximizes the investment and environmental benefits.However,as a significant evaluation,the environmental factors haven’t been considered in the previous study.Considering this factor,the mathematical model of economic insulation thickness of the buried hot oil pipelines is built in this paper,which is solved by the golden section method while considering the costs of investment,operation,environment,the time value of money.The environmental cost is determined according to the pollutant discharge calculated through relating heat loss of the pipelines to the air emission while building the model.The results primarily showed that the most saving fuel is natural gas,followed by LPG,fuel oil,and coal.The fuel consumption for identical insulation thickness is in the order:coal,fuel oil,LPG,and natural gas.When taking the environmental costs into account,the thicker the economic insulation layer is,the higher cost it will be.Meanwhile,the more pollutant discharge,the thicker the economic insulation layer will be.

Model Test Based Soil Spring Model and Application in Pipeline Thermal Buckling Analysis

The buckling of submarine pipelines may occur due to the action of axial soil frictional force caused by relative movement of soil and pipeline, which is induced by the thermal and internal pressure. The likelihood of occurrence of this buckling phenomenon is largely determined by soil resistance. A series of large-scale model tests were carried out to facilitate the establishment of substantial data base for a variety of burial pipeline relationships. Based on the test data, nonlinear soil spring can be adopted to simulate the soil behavior during the pipeline movement. For uplift resistance, an ideal elasticity plasticity model is recommended in the case of H/D （depth-to-diameter ratio）〉5 and an elasticity softened model is recommended in the case of H/D≤5. The soil resistance along the pipeline axial direction can be simulated by an ideal elasticity plasticity model. The numerical analyzing results show that the capacity of pipeline against thermal buckling decreases with its initial imperfection enlargement and increases with the burial depth enhancement.

The influence of DC stray current on pipeline corrosion

DC stray current can cause severe corrosion on buried pipelines.In this study,firstly,we deduced the equation of DC stray current interference on pipelines.Next,the cathode boundary condition was discretized with pipe elements,and corresponding experiments were designed to validate the mathematical model.Finally,the numerical simulation program BEASY was used to study the corrosion effect of DC stray current that an auxiliary anode bed generated in an impressed current cathodic protection system.The effects of crossing angle,crossing distance,distance of the two pipelines,anode output current,depth,and soil resistivity were investigated.Our results indicate that pipeline crossing substantially affects the corrosion potential of both protected and unprotected pipelines.Pipeline crossing angles,crossing distances,and anode depths,our results suggest,have no significant influence.Decreasing anode output current or soil resistivity reduces pipeline corrosion gradually.A reduction of corrosion also occurs when the distance between two parallel pipelines increases.