Thermal Decomposition of Potassium Titanium Hexacyanoferrate(Ⅱ) Loaded with Cesium in a Fixed Bed Calciner

The thermal decomposition of potassium titanium hexacyanoferrate（ Ⅱ ） （KTiFC） loaded with cesium （referred to as Used Exchanger,or UE） was-studied at different flow rate of air in a fixed bed calciner. The calcina t ign processconsisted of four stages：ambient temperature- 180℃ （stageⅠ ）, 180-250℃（stage Ⅱ）, 250-400℃ （stage Ⅲ）, and constant 400℃ （stage Ⅳ）.The most intense reaction occurred in stage .Ⅱ. The rate of thermal decomposition was controlled, depending on the O2 flux, by O2 or CN concentration in ditterent stages. Results from differential thermal analysis （DTA） showed that the calcination reaction of the anhydrous UE was exothermic, with an approximate heat output of 4.6kJ·g^-1, which was so large to cause the possible agglomeration of calcined residues. The agglomeration could be avoided by enhancing heat transfer and controlling the O2 flux. It was found that there was no cyanides in the calcined residues and no CN-bearing gases such as HCN and （CN）2 in the off-gas. It seemed that the catalytic oxidation furnace behind the fixed bed calciner could be cancelled.

Enhanced electrochemical nitrate removal from groundwater by simply calcined Ti nanopores with modified surface characters

A simple and convenient preparation method with high catalytic reduction activity is crucial for the remediation of nitrate contamination.In this study,the innovation for fabricating a nanoelectrode was developed by calcinating the anodized plate to alter the surface crystalline phase of the material.The prepared calcined Ti nanopores(TNPs)electrode could effectively remove up to 95.1%nitrate from simulated groundwater at 30 mA·cm^(-2)electrolysis for 90 min,while under the same conditions,the removal efficiency of nanoelectrode prepared by conventional methods was merely 52.5%.Scanning electron microscopy images indicated that the calcined TNP nanoelectrode was porous with different pore sizes.The higher nitrate removal efficiency of TNPs-500(95.1%)than TNPs-400(77.5%)and TNPs-550(93.4%)may resulted from the positive nonlinear response of the larger electrochemical active surface area,the improved electron transfer and suitable surface structure,and not the“anatase-torutile”of surface TiO_(2)nanotubes.After 90 min of electrolysis,using RuO_(2)as an anode and adding 0.3 g·L^(-1)NaCl solution,87.5%nitrate was removed,and the by-products(ammonia and nitrite)were negligible.Increased temperature and alkaline conditions can enhance the nitrate removal,while higher initial nitrate concentration only improved the nitrate removal slightly.Moreover,The TNPs-500 electrode also exhibited excellent nitrate removal performance in real groundwater with the efficiency at 82.9%and 92.1%after 90 and 120 min,which were 0.87(removal efficiency=95.1%),0.92(removal efficiency=100%)of the efficiency for simulated groundwater,indicating the widely applicable conditions of the TNPs-500 electrode.This approach of surface-bonded elements and structure modification through calcination significantly improves catalytic activity and will guide the simple designing of functional nanostructured electrodes with wide application conditions.

Effect of Na_(2)CO_(3)Roasting Activation on Acid Leaching Property of Fly Ash

By using high-alumina fly ash as raw material,a process was proposed for activating the fly ash with Na_(2)CO_(3)calcination and extracting aluminum from activated clinker with sulfuric acid leaching.The feasibility of roasting process of activated fly ash by Na_(2)CO_(3)was discussed based on thermodynamic analysis.The experimental results showed that Na_(2)CO_(3)gradually reactes with mullite over 700 K to produce NaAlSiO_(4).The optimal process conditions for the activation stage are:a material ratio of 1:1 between sodium carbonate and fly ash,a calcination temperature of 900℃,and a calcination time of 2.5 hours.Under these conditions,the leaching rate of aluminum is 90.3%.By comparing the SEM and XRD analysis of raw and clinker materials,it could be concluded that the mullite phase of fly ash is almost completely destroyed and transformed into sodium aluminosilicate with good acid solubility.

Recycling arsenic-containing bio-leaching residue after thermal treatment in cemented paste backfill:Structure modification,binder properties and environmental assessment

The substantial arsenic(As)content present in arsenic-containing bio-leaching residue(ABR)presents noteworthy environ-mental challenges attributable to its inherent instability and susceptibility to leaching.Given its elevated calcium sulfate content,ABR exhibits considerable promise for industrial applications.This study delved into the feasibility of utilizing ABR as a source of sulfates for producing super sulfated cement(SSC),offering an innovative binder for cemented paste backfill(CPB).Thermal treatment at varying temperatures of 150,350,600,and 800℃ was employed to modify ABR’s performance.The investigation encompassed the examination of phase transformations and alterations in the chemical composition of As within ABR.Subsequently,the hydration characteristics of SSC utilizing ABR,with or without thermal treatment,were studied,encompassing reaction kinetics,setting time,strength development,and microstructure.The findings revealed that thermal treatment changed the calcium sulfate structure in ABR,consequently impacting the resultant sample performance.Notably,calcination at 600℃ demonstrated optimal modification effects on both early and long-term strength attributes.This enhanced performance can be attributed to the augmented formation of reaction products and a densified micro-structure.Furthermore,the thermal treatment elicited modifications in the chemical As fractions within ABR,with limited impact on the As immobilization capacity of the prepared binders.

A thermodynamic view on the in-situ carbon dioxide reduction by biomass-derived hydrogen during calcium carbonate decomposition

In the carbonate industry,deep decarbonization strategies are necessary to effectively remediate CO_(2).These strategies mainly include both sustainable energy supplies and the conversion of CO_(2)in downstream processes.This study developed a coupled process of biomass chemical looping H2 production and reductive calcination of CaCO_(3).Firstly,a mass and energy balance of the coupled process was established in Aspen Plus.Following this,process optimization and energy integration were implemented to provide optimized operation conditions.Lastly,a life cycle assessment was carried out to assess the carbon footprint of the coupled process.Results reveal that the decomposition temperature of CaCO_(3)in an H_(2)atmosphere can be reduced to 780℃(generally around 900℃),and the conversion of CO_(2)from CaCO_(3)decomposition reached 81.33%with an H2:CO ratio of 2.49 in gaseous products.By optimizing systemic energy through heat integration,an energy efficiency of 86.30%was achieved.Additionally,the carbon footprint analysis revealed that the process with energy integration had a low global warming potential(GWP)of-2.624 kg·kg^(-1)(CO_(2)/CaO).Conclusively,this work performed a systematic analysis of introducing biomass-derived H_(2)into CaCO_(3)calcination and demonstrated the positive role of reductive calcination using green H_(2)in mitigating CO_(2)emissions within the carbonate industry.

Controllable synthesis of CuAlO_(2) via solid-phase method and its catalytic performance for methanol steam reforming to hydrogen

This study explores the controllable synthesis of CuAlO_(2) using copper hydroxide and pseudo-boehmite powders as raw materials via a simple solid-phase ball milling method,along with its catalytic performance investigation in methanol steam reforming(MSR).Various catalysts were prepared under different conditions,such as calcination temperature,calcination atmosphere,and heating rate.Characterization techniques including BET,XRD,XPS,SEM and H2-TPR were employed to analyze the samples.The results revealed significant effects of calcination temperature on the phase compositions,specific surface area,reduction performance,and surface properties of the CA-T catalysts.Based on the findings,a synthesis route of CuAlO_(2) via the solid-phase method was proposed,highlighting the importance of high calcination temperature,nitrogen atmosphere,and low heating rate for CuAlO_(2) formation.Catalytic evaluation data demonstrated that CuAlO_(2) could catalyze MSR without pre-reduction,with the catalytic performance of CA-T catalysts being notably influenced by calcination temperature.Among the prepared catalysts,the CA-1100 catalyst exhibited the highest catalytic activity and stability.The findings of this study might be useful for the further study of the catalytic material for sustained release catalysis,including the synthesis of catalytic materials and the regulation of sustained release catalytic performance.

Preparation and Characterization of Activated Carbons from Palm Nut Shells: Effects of Calcination Temperature on Porosity and Chemical Properties

Activated carbons (ACs) calcined at 400˚C, 500˚C, and 600˚C (AC-400, AC-500, and AC-600) were prepared using palm nut shells from Gabon as raw material and zinc chloride (ZnCl2) as a chemical activating agent. Prepared ACs were characterized by physisorption of nitrogen (N2), determination of diode and methylene blue numbers for studies of porosity and by quantification and determination of surface functional groups and pH at point of zero charge (pHpzc) respectively, for studies of chemical properties of prepared ACs. Then, effects of calcination temperature (Tcal) on porosity and chemical properties of prepared ACs were studied. The results obtained showed that when the calcination temperature increases from 500˚C to 600˚C, the porosity and chemical properties of prepared ACs are modified. Indeed, the methylene blue and iodine numbers determined for activated carbons AC-400 (460 and 7.94 mg·g−1, respectively) and AC-500 (680 and 8.90 mg·g−1, respectively) are higher than those obtained for AC-600 (360 and 5.75 mg·g−1, respectively). Compared to the AC-500 adsorbent, specific surface areas (SBET) and microporous volume losses for AC-600 were estimated to 44.7% and 45.8%, respectively. Moreover, in our experimental conditions, the effect of Tcal on the quantities of acidic and basic functional groups on the surface of the ACs appears negligible. In addition, results of the pHpzc of prepared ACs showed that as Tcal increases, the pH of the adsorbents increases and tends towards neutrality. Indeed, a stronger acidity was determined on AC-400 (pHpzc = 5.60) compared to those on AC-500 and AC-600 (pHpzc = 6.85 and 6.70, respectively). Also according to the results of porosity and chemical characterizations, adsorption being a surface phenomenon, 500˚C appears to be the optimal calcination temperature for the preparation of activated carbons from palm nut shells in our experimental conditions.

Highly active Cu/SiO_2 catalysts for hydrogenation of diethyl malonate to 1,3-propanediol

Cu/SiO2 catalysts prepared by the ammonia evaporation method were applied to hydrogenation of diethyl malonate to 1,3‐propanediol. The calcination temperature played an important role in the structural evolution and catalytic performance of the Cu/SiO2 catalysts, which were systematically characterized by N2 adsorption‐desorption, inductively coupled plasma‐atomic emission spectros‐copy, N2O chemisorption, X‐ray diffraction, Fourier transform infrared spectroscopy, H2 tempera‐ture‐programmed reduction, transmission electron microscopy, and X‐ray photoelectron spectros‐copy. When the Cu/SiO2 catalyst was calcined at 723 K, 90.7%conversion of diethyl malonate and 32.3%selectivity of 1,3‐propanediol were achieved. Compared with Cu/SiO2 catalysts calcined at other temperatures, the enhanced catalytic performance of the Cu/SiO2 catalyst calcined at 723 K can be attributed to better dispersion of copper species, larger cupreous surface area and greater amount of copper phyllosilicate, which results in a higher ratio of Cu＋/Cu0. The synergetic effect of Cu0 and Cu＋is suggested to be responsible for the optimum activity.

Optimization of preparing V_2O_5 by calcination from ammonium metavanadate using response surface methodology

Parameters of technique to prepare vanadium pentoxide by calcination from ammonium metavanadate were optimized using central composite design of response surface methodology. A quadratic equation model for decomposition rate was built and effects of main factors and their corresponding relationships were obtained. The results of the statistical analysis show that the decomposition rate of ammonium metavanadate is significantly affected by calcination temperature and calcination time. The optimized calcination conditions are as follows： calcination temperature 669.71 K, calcination time 35.9 min and sample mass 4.25 g. The decomposition rate of ammonium metavanadate is 99.71%,which coincides well with experimental value of 99.27% under the optimized conditions, suggesting that regressive equation fits the decomposition rates perfectly. XRD reveals that it is feasible to prepare the V2O5 by calcination from ammonium metavanadate using response surface methodology.

Element distribution of high iron-bearing zinc calcine in high gradient magnetic field

High gradient magnetic separation was conducted in order to separate insoluble zinc ferrite from zinc calcine before acid leaching of hydrometallurgical process. Chemical composition and structural characterization of zinc calcine were studied via inductively coupled plasma （ICP）, X-ray diffraction （XRD）, Mossbauer spectra, scanning electron microscopy （SEM） and laser particle analysis （LPA）. The parameters of magnetic separation which affect the distribution of zinc ferrite and undesired elements, such as calcium, sulfur and lead in magnetic concentrate were investigated. The results of high gradient magnetic separation indicate that more than 85% of zinc ferrite is distributed into magnetic concentrate from the zinc calcine under the magnetic induction of 0.70 T. In addition, about 60% of calcium and 40% of sulfur distribute in non magnetic phases of tailings during magnetic separation process. Most of lead distributes uniformly along the zinc calcine in superfine particle size.

Effect of Calcination Temperature on Catalytic Activity and Textual Property of Cu/HMOR Catalysts in Dimethyl Ether Carbonylation Reaction

The effect of calcination temperature on the catalytic activity for the dimethyl ether （DME） carbonylation into methyl acetate （MA） was investigated over mordenite supported copper （Cu/HMOR） prepared by ion-exchange process. The results showed that the catalytic activity was obviously affected by the calcination temperature. The maximal DME conversion of 97.2% and the MA selectivity of 97.9% were obtained over the Cu/HMOR calcined at 430 ℃ under conditions of 210 ℃, 1.5 MPa, and GSHV of 4883 h^-1. The obtained Cu/HMOR catalysts were characterized by powder X-ray diffraction, N2 absorption, NH3 temperature program desorption, CO temperature program desorption, and Raman techniques. Proper calcination temperature was effective to promote copper ions migration and diffusion, and led the support HMOR to possess more acid activity sites, which exhibited the complete decomposing of copper nitrate, large surface area and optimum micropore structure, more amount of CO adsorption site and proper amount of weak acid centers.

Effect of Calcination Temperature on La-Modified Al2O3 Catalysts for Vapor Phase Hydrofluorination of Acetylene to Vinyl Fluoride

A La-modified Al2O3 catalyst was prepared with deposition-precipitation method. The effect of calcination temperature on the reactivity for vapor phase hydrofluorination of acetylene to vinyl fluoride. The catalysts calcined at different temperatures were characterized using NH3-TPD, pyridine-FTIR, X-ray diffraction, and Raman techniques. It was found that the calcination process could not only change the structure of these catalysts but also modify the amount of surface acidity on the catalysts. The catalyst calcined at 400 ℃ exhibited the highest conversion of acetylene （94.6%） and highest selectivity to vinyl fluoride （83.4%） and lower coke deposition selectivity （0.72%）. The highest activity was related to the largest amount of surface acidity on the catalyst, and the coke deposition was also related to the total amount of surface acidic sites.

Low temperature molten salt synthesis of porous La_(1-x)Sr_xMn_(0.8)Fe_(0.2)O_3(0≤x≤0.6) microspheres with high catalytic activity for CO oxidation

A molten salt method was developed to prepare porous La1‐xSrxMn0.8Fe0.2O3 （0≤ x ≤ 0.6） micro‐spheres using hierarchical porous δ‐MnO2 microspheres as a template in eutectic NaNO3‐KNO3. X‐ray diffraction patterns showed that single phase LaMn0.8Fe0.2O3 with good crystallinity was syn‐thesized at 450℃ after 4 h. Transmission electron microscope images exhibited that the LaMn0.8Fe0.2O3 sample obtained at 450？？ after 4 h possessed a porous spherical morphology com‐posed of aggregated nanocrystallites. Field emission scanning electron microscope images indicated that the growth of the porous LaMn0.8Fe0.2O3 microspheres has two stages. SEM pictures showed that a higher calcination temperature than 450？？ had an adverse effect on the formation of a po‐rous spherical structure. The LaMn0.8Fe0.2O3 sample obtained at 450？？ after 4 h displayed a high BET surface area of 55.73 m2/g with a pore size of 9.38 nm. Fourier transform infrared spectra suggested that Sr2＋ions entered the A sites and induced a decrease of the binding energy between Mn and O. The CO conversion with the La1‐xSrxMn0.8Fe0.2O3 （0≤x≤0.6） samples indicated that the La0.4Sr0.6Mn0.8Fe0.2O3 sample had the best catalytic activity and stability. Further analysis by X‐ray photoelectron spectroscopy demonstrated that Sr2＋doping altered the content of Mn4＋ions, oxygen vacancies and adsorbed oxygen species on the surface, which affected the catalytic performance for CO oxidation.

Adsorption of glutamic acid from aqueous solution with calcined layered double Mg-Fe-CO_3 hydroxide

Layered double Mg-Fe-CO3 hydroxide （Mg-Fe-LDH） with a mole ratio of Mg to Fe of 3 was synthesized by coprecipitation method and calcined product Mg-Fe-CLDH was obtained by heating Mg-Fe-LDH at 500 ℃ for 6 h. The as prepared Mg-Fe-LDH and calcined Mg-Fe-CLDH were used for removal of glutamic acid （Glu） from aqueous solution, respectively. Batch studies were carried out to address various experimental parameters such as contact time, pH, initial glutamic acid （Glu） concentration, co-existing anions and temperature. Glu was removed effectively （99.9%） under the optimized experimental conditions with Mg-Fe-CLDH. The adsorption kinetics follows the Ho’s pseudo second-order model. Isotherms for adsorption with Mg-Fe-CLDH at different solution temperatures were well described using the Langmuir model with a good correlation coefficient. The intraparticle diffusion model fitted the data well, which suggests that the intraparticle diffusion is not only the rate-limiting step.

含钙废弃物煅烧固硫性能的热分析试验研究

利用TGA/SDTA851e热分析系统研究了含钙废弃物和石灰石煅烧、固硫反应过程,用多重速率法计算了其煅烧反应活化能。并对含钙废弃物的化学成分对其煅烧特性和固硫活性的影响进行了探讨,为进一步分析含钙废弃物的脱硫机理提供理论依据。结果表明,在相同煅烧条件下,白泥煅烧的TG曲线要比石灰石的TG曲线向低温方向偏移,盐泥和碱渣虽开始分解温度低于石灰石,但其中止分解温度却高于石灰石;一定量SiO2的存在,能使煅烧反应速度加快,煅烧活化能降低,生成CaO的活性提高,而Al2O3、Fe2O3含量较高时,会造成一定的孔堵塞或形成熔融孔,煅烧活化能增加,生成CaO的活性降低。

Model of limestone calcination / sulfation under oxy-fuel fluidized bed combustion

The characteristics of the simultaneous calcination/ sulfation of limestone under oxy-fuel fluidized bed combustion were studied and compared with those of the sulfation of precalcined CaO. During the calcination stage, SO2 can react with product CaO and slow down the CaCO3 decomposition rate by the covering effect of the CaSO4 product. The sulfation rate of simultaneous calcinatiort/sulfation is slower than that of precalcined CaO, but with a long enough sulfation time, the calcium conversion of simultaneous calcination/sulfation is higher than that of the precalcined CaO. A grain-micrograin model is established to describe the simultaneous calcination, sintering and sulfation of limestone. The graln-micrograln model can reflect the true reaction process of the calcination and sulfation of limestone in oxy-fuel fluidized bed combustion.

An Evaluation Method for Combustion Characteristics of Coal in Cement Industry

As the coal combustion behaviors are rather complex in the cement industry, the traditional assessment method cannot be directly applied to evaluate the quality of coal. Based on the thermal analysis tests of more than 80 kinds of anthracite and bituminous coal, three evaluation parameters, namely, burning intensity （I）, average capacity of heat release （Q）, and general burning index （S） are presented, combining with the consideration of application and calciner types in the cement industry. Taking these three parameters into consideration together is necessary. Experimental results show that the coal with higher S, lower I and higher Q can be rated as the best for the calciner in the cement industry. The quantitative indexes are given to evaluate the bituminous coal and anthracite in this paper. This new assessment method has implications for the design of calciner in the cement industry.

Solvent-free selective oxidation of cyclohexane with molecular oxygen over manganese oxides:Effect of the calcination temperature

The effects of calcination temperature on the physicochemical properties of manganese oxide catalysts prepared by a precipitation method were assessed by X-ray diffraction,N2 adsorption-desorption,X-ray photoelectron spectroscopy,H2 temperature-programmed reduction,O2 temperature-programmed desorption,and thermogravimetry-differential analysis.The catalytic performance of each of these materials during the selective oxidation of cyclohexane with oxygen in a solvent-free system was subsequently examined.It was found that the MnOx-500 catalyst,calcined at 500 °C,consisted of a Mn2O3 phase in addition to Mn5O8 and Mn3O4 phases and possessed a low surface area.Unlike MnOx-500,the MnOx-400 catalyst prepared at 400 °C was composed solely of Mn3O4 and Mn5O8 and had a higher surface area.The pronounced catalytic activity of this latter material for the oxidation of cyclohexene was determined to result from numerous factors,including a higher concentration of surface adsorbed oxygen,greater quantities of the surface Mn4＋ ions that promote oxygen mobility and the extent of O2 adsorption and reducibility on the catalyst.The effects of various reaction conditions on the activity of the MnOx-400 during the oxidation of cyclohexane were also evaluated,such as the reaction temperature,reaction time,and initial oxygen pressure.Following a 4 h reaction at an initial O2 pressure of 0.5 MPa and 140 °C,an 8.0% cyclohexane conversion and 5.0% yield of cyclohexanol and cyclohexanone were achieved over the MnOx-400 catalyst.In contrast,employing MnOx-500 resulted in a 6.1% conversion of cyclohexane and 75% selectivity for cyclohexanol and cyclohexanone.After being recycled through 10 replicate uses,the catalytic activity of the MnOx-400 catalyst was unchanged,demonstrating its good stability.

Effect of Calcination Temperature on Surface Oxygen Vacancies and Catalytic Performance Towards CO Oxidation of Co3O4 Nanoparticles Supported on SiO2

Co3O4/SiO2 catalysts for CO oxidation were prepared by conventional incipient wetness impregnation followed by calcination at various temperatures. Their structures were char- acterized with X-ray diffraction （XRD）, laser Raman spectroscopy, X-ray photoelectron spectroscopy （XPS）, temperature-programmed reduction （TPR） and X-ray absorption fine structure （XAFS） spectroscopy. Both XRD and Raman spectroscopy only detect the existence of Co3O4 crystallites in all catalysts. However, XPS results indicate that excess Co2＋ ions are present on the surface of Co3O4 in Co3O4（200）/Si02 as compared with bulk Co3O4. Meanwhile, TPR results suggest the presence of surface oxygen vacancies on Co3O4 in Co3O4（200）/SiO2, and XAFS results demonstrate that Co3O4 in Co3O4（200）/SIO2 contains excess Co2＋. Increasing calcination temperature results in oxidation of excess Co2＋ and the decrease of the concentration of surface oxygen vacancies, consequently the for- mation of stoichiometric Co3O4 on supported catalysts. Among all Co3O4/SiO2 catalysts, Co3O4（200）/SiO2 exhibits the best catalytic performance towards CO oxidation, demonstrating that excess Co2＋ and surface oxygen vacancies can enhance the catalytic activity of Co3O4 towards CO oxidation. These results nicely demonstrate the effect of calcination temperature on the structure and catalytic performance towards CO oxidation of silicasupported Co3O4 catalysts and highlight the important role of surface oxygen vacancies on Co3O4.

Extraction and characterization of alumina nanopowders from aluminum dross by acid dissolution process

A significant amount of aluminum dross is available as a waste in foundry industries in Bangladesh. In this study, alumina was ex- tracted from aluminum dross collected from two foundry industries situated in Dhamrai and Manikgang, near the capital city, Dhaka. Alu- minum dross samples were found to approximately contain 75wt% A1203 and 12wt% SIO2. An acid dissolution process was used to recover the alumina value from the dross. The effects of various parameters, e.g., temperature, acid concentration, and leaching time, on the extrac- tion of alumina were studied to optimize the dissolution process. First, AI（OH）3 was produced in the form of a gel. Calcination of the AI（OH）3 gel at 1000℃, 1200℃, and 1400℃ for 2 h produced O-AlcOa, （t~＋O）-A1203, and u-alumina powder, respectively. Thermal charac- terization of the AI（OH）3 gel was performed by thermogravimetric/differential thermal analysis （TG/DTA） and differential scanning calo- rimetry （DSC）. The phases and crystallite size of the alumina were determined by X-ray diffraction analysis. The dimensions of the alumina were found to be on the nano level. The chemical compositions of the aluminum dross and alumina were determined by X-ray fluorescence （XRF） spectroscopy. The microstructure and morphology of the alumina were studied with scanning electron microscopy. The purity of the alumina extracted in this study was found to be 99.0%. Thus, it is expected that the obtained alumina powders can be potentially utilized as biomaterials.