Properties and calculation of normal section bearing capacity of RC flexural beam with skin textile reinforcement

In order to overcome the wide crack of ordinary reinforced concrete (RC) at service stage which affects the service performance and durability of structures,a kind of concrete structure with skin textile reinforcement is proposed,namely a part of concrete cover of RC members is replaced by textile reinforced concrete (TRC).The flexural experimental results indicate that when the reinforcement ratios of steel bars are constant,compared with control beams,the average value of crack loads of the beams,whose reinforcement ratios of textile are 0.018%,0.036% and 0.055%,increases by 15.5%,20.4% and 31.1%,respectively,the average value of yield loads respectively increases by 12.5%,19.9% and 21.1% and the average value of ultimate loads respectively increases by 8.5%,26.0% and 44.0%,respectively.Considerable reduction in cracks width and spacing is observed for specimens with a TRC layer,and when the beams yield,the maximum crack width of the beam with textile stuck no sand and the beam with textile stuck sand is reduced by around 60% and 70%,respectively.Surface treatment of textile and mixing polypropylene fiber into fine grained concrete contribute to enhance the service performance of the flexural element.Embedding U-shaped hoop has almost no effect on the control of the crack width.Finally,the calculation method of ultimate bearing capacity of this flexural component with TRC layer was presented.Comparison between the calculated and the experimental values reveals satisfactory agreement,and the maximum error is no more than 6%.

Flow Calculation of Water Environmental Capacity Controlling Units in a Small Watershed Based on GIS Technology

[Objeetive] We aimed to calculate the flow of controlling units in a small watershed based on GIS technology. [Method] Hydrologic analysis on Qingyi River was conducted by using ArcGIS9.0, and the controlling units with response of water-land were divided according to the riv- er monitoring sections of Xuchang City; considering the wastewater entering the river and the water from its upper reach, the runoff of controlling sections in the driest month （ with guarantee rate of 90% ） was calculated by means of isoline, runoff coefficient and hydrologic analogy method, and the calculated value of Gaocun Bridge section in Linying was contrasted with the measured value in 2010. [Result] The results showed that the cal- culated value and measured value of Gaecun Bridge section in Linying in the driest month of 2010 were 6.03 and 5.93 m^3/s respectively, with relative error of 1.69%, which revealed that the result of calculated runoff was reasonable. [ Conclusion] The way to divide controlling units was reason- able, and the calculation result of runoff was accurate and can meet the precision of water environment capacity calculation.

Calculation of railway transport capacity in an emergency based on Markov process

A method is proposed to calculate the railway transport capacity in an emergency to support the dispatching work of control centers. The effect of an emergency on section transport capacity is analyzed and the basic method to calculate the transport capacity is presented. The results show that the situation-changing process in emergency is actually a Markov process. The calculation rule is presented based on division of the time segment during which the emergency lasts. The algorithm is designed to calculate the transport capacity of each time segment. The pessimistic strategy and the fuzzy strategy are proposed to determine the computing value of the transport capacity of each time segment, to satisfy the calculating requirements in different occasions. Our study shows that the method is reasonable and practical and the method can be embedded in the train dispatching system to support the operation work in an emergency.

CAPACITY CALCULATION OF TD-CDMA HIGH ALTITUDE PLATFORM SYSTEM

A capacity calculation method of High Altitude Platform System(HAPS) is proposed in which TD-CDMA multiple access schemes are applied.With the influence of both power limit and bandwidth limit on capacity integrated,the paper derives the equations by which the capacity of TD-CDMA systems can be calculated,and performs calculation on a practical system.This calculation method is quite simple and effective with a comparatively small error,which is essential to the de-signing and research on HAPS.

Analysis of Bridge-Bearing Capacity Detection and Evaluation Technology

A bridge project is taken as an example to analyze the application of bearing capacity detection and evaluation.This article provides a basic overview of the project,the application of bearing capacity detection technology,and the bearing capacity assessment analysis.It is hoped that this analysis can provide a scientific reference for the load-bearing capacity detection and evaluation work in bridge engineering projects,thereby achieving a scientific assessment of the overall load-bearing capacity of the bridge engineering structure.

Evaluation of optimal UPFC allocation for improving transmission capacity

A unified power flow controller(UPFC)combines the advantages of various flexible alternating current transmission system(FACTS)devices into a powerful format.Using a 500 kV power grid,this study evaluates the selection and use of a UPFC to improve transmission capacity.The"UPFC unit capacity control proportionality coefficient"is introduced to quantify the control effect of the UPFC,and an optimal calculation method for the UPFC capacity is presented.Following the proposal of a UPFC site selection process,the data of an existing power grid is used to conduct simulations.The simulation results show that the UPFC has a strong ability to improve transmission capacity,and its use is greatly advantageous.Additionally,by applying the proposed selection method,the control effect and economic benefits of the UPFC can be comprehensively considered during project site selection.These findings have a guiding significance for UPFC site selection in ultra-high voltage power grids.

An Improved Method of Predicting Drag Anchor Trajectory Based on the Finite Element Analyses of Holding Capacity

Drag anchor is one of the most commonly used anchorage foundation types. The prediction of embedded trajectory in the process of drag anchor installation is of great importance to the safety design of mooring system. In this paper, the ultimate anchor holding capacity in the seabed soil is calculated through the established finite element model, and then the embedded motion trajectory is predicted applying the incremental calculation method. Firstly, the drag anchor initial embedded depth and inclination angle are assumed, which are regarded as the start embedded point. Secondly, in each incremental step, the incremental displacement of drag anchor is added along the parallel direction of anchor plate, so the displacement increment of drag anchor in the horizontal and vertical directions can be calculated. Thirdly, the finite element model of anchor is established considering the seabed soil and anchor interaction, and the ultimate drag anchor holding capacity at new position can be obtained. Fourthly, the angle between inverse catenary mooring line and horizontal plane at the attachment point at this increment step can be calculated through the inverse catenary equation. Finally, the incremental step is ended until the angle of drag anchor and seabed soil is zero as the ultimate embedded state condition, thus, the whole embedded trajectory of drag anchor is obtained. Meanwhile, the influences of initial parameter changes on the embedded trajectory are considered. Based on the proposed method, the prediction of drag anchor trajectory and the holding capacity of mooring position system can be provided.

Comparison Structure Forms Between Isogrid and Orthogrid of C/E Composite Trellis Wound Structure Based on Calculation of Load-Carrying

This paper calculated load-carrying of isogrid and orthogrid of carbon-epoxy composite trellis wound structure(C/E CTWS) using non-linear finite element method.Based on the analysis,test cases were designed and tests of axial compression were carried.Analysis result and test result fit well.In order to be used in the project,this kind of structure cut-out repairing was calculated.The method presented in this paper has been proved and can be used to solve complicated engineering problems.According to calculations and experimental results combined with application,a principle of choosing wound structure is obtained and principle could be applied to engineering.

板柱节点考虑弯剪相关性的受冲切承载力计算方法

对于同时受到竖向荷载和不平衡弯矩作用的板柱节点,目前已有方法大多将不平衡弯矩等效为竖向荷载,从而给出其受冲切承载力计算方法。但该方法所涉及的不平衡弯矩比例系数的计算还存在较大争议,且没有考虑竖向荷载与不平衡弯矩耦合的影响。因此,本文首先通过推导给出仅有竖向荷载作用的板柱节点受冲切承载力计算公式和仅有不平衡弯矩作用的板柱节点受弯承载力计算公式,并与试验结果进行对比,验证了所提公式的合理性。然后基于板柱节点在竖向荷载和不平衡弯矩共同作用下的试验结果,拟合得到板柱节点考虑弯剪相关性的受冲切承载力计算公式。最后对所提计算方法与不同规范计算方法进行对比,结果表明本文计算方法能够更加准确地预测板柱节点受冲切承载力。

Calculation methodology of marine environmental capacity for heavy metal:A case study in Jiaozhou Bay,China

Results from past pollution control practices show that environmental quality can be ensured by controlling the actual amount of pollutants formed in the environment.Therefore,the marine environmental capacity for heavy metals was introduced.Marine environmental capacity for heavy metals is defined as the maximum amount of heavy metals permitted in the marine environment system to preserve the benign cycle of materials in the oceansphere,and to limit the adverse effects of heavy metals on the biosphere,hydrosphere,atmosphere,and lithosphere.Based on the box or three-dimensional model in the target coastal region,including the self-purification and output of heavy metals,the marine environmental capacity for heavy metals can be calculated within a given criterion and time.In this study,a method was proposed to calculate the marine environmental capacity for heavy metals which includes four steps:(1) gathering the basis information of target coastal ecosystem,(2) selection of water control points and water quality criteria for these points,(3) development of numerical models for the biogeochemical cycling of heavy metals in target coastal region,and(4) calculation of environmental capacity using the developed model.According to the proposed method,the marine environmental capacity for lead is approximately 60 tons per year if Grade I seawater quality is set as the control criterion in Jiaozhou Bay.An effective seawater quality management plan can also be framed based on the environmental capacity for metals.

拼接成型UHPC免拆模板钢筋混凝土柱的抗震性能

为研究超高性能混凝土(UHPC)免拆模板钢筋混凝土(URC)柱的抗震性能,选取UHPC免拆模板拼接方式和表面处理方式为试验设计参数,制作并完成了9个URC柱和1个钢筋混凝土(RC)柱的拟静力加载试验。模板拼接方式为螺栓加角钢连接、螺栓连接和环氧树脂砂浆连接;表面处理方式为光面处理、气泡膜印花处理和设肋处理,通过拟静力试验研究了模板拼接方式及表面处理方式对该类柱抗震性能的影响。此外,基于平截面假定,提出了URC柱的正截面偏压承载力计算式。结果表明:峰值荷载前,UHPC模板与核心混凝土黏结面无明显破坏,URC柱表现出良好的整体性,尤其是采用螺栓加角钢连接的URC柱,即使加载至极限位移时,也没有发生界面黏结失效破坏;与普通RC柱相比,URC柱的承载力提高了6.4%~43.3%,延性提高了11.4%~48.7%,耗能能力提高了27.7%~85.3%;三种连接方式中,采用螺栓加角钢连接的URC柱承载力最高,连接最可靠。最后,基于平截面假定提出的公式计算值与试验值吻合较好,可为工程应用提供参考。

圆钢管超高性能混凝土短柱偏压力学性能研究

为研究钢管超高性能混凝土短柱的偏压性能,以荷载偏心率和钢管径厚比为变化参数,设计了12个圆钢管UHPC短柱试件并对其进行偏心受压加载试验,分析了该类构件的破坏模式、荷载-挠度曲线、钢管应变和变形系数等,考察了主要因素对短柱偏压性能的影响规律。结果表明:试件的破坏特征为钢管屈服和核心混凝土压坏;荷载-挠度曲线有较明显的峰值点,偏心率越大和径厚比越小,曲线的下降段越平缓;达到60%峰值荷载时,钢管开始产生明显的约束作用,达到90%峰值荷载时,截面变形不再符合平截面假定;偏心率增大使试件的承载力和刚度下降,而径厚比减小可降低这种不利影响。在试验基础上,结合数值模拟对短柱的N-M曲线进行分析,建立了临界偏心率和套箍系数的关系表达式,并基于此提出短柱偏压承载力实用计算方法,理论与试验结果吻合较好。

钢筋增强钢夹板-螺栓连接胶合木梁受力性能试验研究

为改善钢夹板-螺栓连接胶合木梁的刚度在到达极限荷载55%~70%区间内存在减小的问题,设计制作了3组共12根钢筋增强钢夹板-螺栓连接胶合木梁,通过改变配筋率进行三分点加载试验,并与相同设计参数的胶合木梁和钢夹板-螺栓连接胶合木梁进行对比试验。观察记录试件的受力过程和破坏现象,实测各组试件的极限承载力、荷载位移曲线和应变曲线,对比分析增强筋对各组试件破坏机理、抗弯刚度和极限承载力的影响规律。试验结果表明:与钢夹板-螺栓连接胶合木梁相比,钢筋增强钢夹板-螺栓连接胶合木梁的抗弯承载力和整体弯曲刚度在增强筋的作用下均有显著提高,钢夹板-螺栓连接试验梁在到达极限荷载55%~70%区间内刚度减少问题得到明显改善。钢筋增强钢夹板-螺栓连接试验梁的破坏形式随着配筋率的增大,逐渐由受拉脆性破坏向受拉延性破坏再到受压延性破坏进行转变。增强梁截面应变沿高度方向的分布基本符合平截面假定。依据试验数据和理论推导,得出了钢筋增强钢夹板-螺栓连接试验梁抗弯计算公式,其理论结果与试验结果吻合较好。研究表明,在钢夹板-螺栓连接胶合木梁受拉区配置增强筋可以有效改善其后期刚度减少的问题,并提升其抗弯性能,可为此类连接木梁的增强提供理论依据和试验支撑。

数字孪生水网建设应着力解决的几个关键问题

数字孪生水网建设涉及多学科交叉、新技术融合,有诸多重点和难点,应着力把握好坚持问题导向、夯实算据基础、优化算法核心、强化算力支撑、着力业务应用、加强网络安全等关键问题。结合数字孪生水网建设先行先试经验,围绕工程安全、供水安全、水质安全,提出了数字孪生水网建设的关键问题及解决思路:围绕建设目标确定建设内容和重点,以问题为导向开展需求分析;打造“天空地”一体化监测感知体系,完善地面监测站网、提升新型监测感知能力、强化数据治理与运用、推进数据资源共享夯实算据基础;完善模型平台,开发知识平台,优化算法核心;建设信创云平台和高性能计算集群,扩充计算资源、升级通信网络强化算力支撑;提升水网智慧调控能力,着力实现业务“四预”;构建网络安全体系,保障网络和数据安全;理清数字孪生流域、数字孪生水网、数字孪生工程的关系,提升整体效能。

地基承载力特征值确定土变形模量的探讨

目前我国地基沉降计算主要采用土压缩模量来计算,再用经验系数对计算结果进行修正。这种方法对于一些结构性较强的硬土地基误差较大,主要原因是取样扰动影响。为此,探讨了变形模量与地基承载力特征值的理论联系,在笔者提出的确定变形模量经验方法基础上,总结出依据地基承载力特征值确定变形模量的方法,该方法具有理论依据,可便捷地通过岩土工程勘察报告中常提供的地基承载力特征值确定土的变形模量,能够更为准确计算地基沉降值。采用不同方法(压板试验法、压缩模量推求法、标贯击数法、承载力经验法、依据地基承载力特征值确定变形模量法)计算了若干试验案例,通过对不同方法结果的对比,初步验证了依据地基承载力特征值确定变形模量法是可行的。

新建公路隧道上跨既有铁路隧道稳定性影响研究

为明确新建隧道施工及夹层岩土体厚度、围岩级别等不同因素对既有隧道结构稳定性的影响作用,以新建公路隧道上跨既有铁路隧道工程为依托,采用数值计算的研究方法,探讨了不同夹层岩土体厚度及围岩等级下近接隧道施工对既有隧道结构受力和变形的影响规律,并利用现场试验验证了计算模型的准确性,同时通过检算隧道结构各部位的安全系数,对近接隧道施工安全性进行了评价。结果表明:(1)新建公路隧道与既有铁路隧道夹层厚度对既有铁路隧道拱顶和轨道面的受力和变形影响显著。当夹层土厚度在0~16 m时,既有结构的受力和变形受新建隧道施工影响较大,当厚度大于31 m时,基本不受影响。既有结构变形随夹土层厚度增加逐渐减小;(2)既有铁路隧道结构应力随着围岩级别的降低而增大,但非线性关系,Ⅵ级和Ⅴ级围岩条件下较Ⅳ级围岩应力分别增长了12.3%和36.8%;(3)现场监测数据表明既有隧道拱顶和轨面处的竖向位移曲线均呈倒“W”形,变形量实测值与数值计算值偏差在20%以内,验证了计算模型的可靠性;(4)既有隧道结构承载力受新建隧道的影响较小,未出现衬砌结构的拉压破坏,满足相关规范的安全评估要求。

间断焊接包管加固圆钢管构件轴压极限承载力研究

为研究间断焊接包管加固杆件的轴心受压性能,设计了13组试件进行单调加载静力试验。对试件极限承载力、破坏模式、荷载-位移曲线和截面应变发展规律进行分析,对比了负载加固与非负载加固对试件极限承载力的影响。结果表明:包管构件的破坏模式可分为整体失稳破坏和内管外伸段强度破坏;包管构件内外管协同工作、共同受力,内管和外管都在屈服后发生整体失稳破坏;负载加固与非负载加固试件的极限承载力基本一致,相差2.2%,非负载加固试件与未加固试件相比,极限承载力最大提高了479.9%。根据试验结果对包管构件的ABAQUS有限元模型进行修正,并用该模型分析了各主要影响因素对包管构件极限承载力的影响规律。提出了包管构件极限承载力经验计算公式,且公式计算结果与试验结果吻合较好。

CFRP布加固RC柱细观力学分析模型及抗扭分析

为了探究配纤率、截面形状、截面尺寸、轴压比对碳纤维增强复合材料(carbon fiber reinforced polymer,CFRP)加固钢筋混凝土(reinforced concrete,RC)柱抗扭性能的影响,采用了可以同时考虑混凝土材料非均质性、钢筋与混凝土间黏结-滑移关系、CFRP布与混凝土间界面关系的细观力学分析方法。首先,建立了用于CFRP布加固RC柱抗扭性能分析的三维数值模型;进而,将基于该模型的数值模拟结果与试验结果对比,验证了模型中加载方式、外贴CFRP布方法的合理性及材料参数的准确性;最后,基于建立的细观力学分析模型,探讨了配纤率、截面形状、截面尺寸、轴压比对扭转作用下CFRP布加固RC柱破坏模式和力学性能的影响机制。分析结果表明:CFRP布加固RC柱抗扭承载力随配纤率增大而提高,但提高幅度随配纤率增大而降低;受到围压分布的影响,圆形截面的有效约束面积大于方形截面,使得CFRP布对圆柱的约束效果好于方柱;CFRP布加固RC柱的名义扭转强度存在尺寸效应;轴压比的增大使其抗扭承载力先增大后减小,在轴压比为0.4时达到最大值。进一步,采用叠加规范公式方法提出了FRP布加固RC构件抗扭承载力计算公式,与数值模拟结果对比发现,该公式可给出安全储备冗余度30.2%的设计值,可初步用于CFRP布加固RC柱抗扭承载力的安全设计。

FRP筋混凝土短梁抗剪性能试验研究及承载力计算

为分析梁高、剪跨比、腹筋率等参数对纤维增强聚合物(FRP)筋混凝土短梁抗剪承载力的定量影响,并验证前期基于拉杆拱模型提出的抗剪承载力计算方法的科学合理性,对11根玄武岩FRP筋混凝土短梁开展了剪切破坏试验,试验梁最大梁高为1.2 m.试验结果表明,梁高、剪跨比、水平腹筋率、竖向腹筋率均对FRP筋混凝土短梁的抗剪承载力有显著影响.当梁高由300 mm增大到1200 mm,试验梁的无量纲极限抗剪强度下降46.7%.当水平腹筋率由0增大至1.0%,试验梁的无量纲极限抗剪强度提高40.5%.基于拉杆拱模型提出的抗剪承载力计算式可以合理反映梁高、剪跨比、水平腹筋率等因素的影响规律,计算结果与本试验结果及搜集试验数据均吻合良好.

局部环向变厚度方钢管混凝土柱偏压力学性能研究

针对海洋环境中飞溅区造成的钢管混凝土柱局部环向腐蚀现象,采用机械削减方式模拟钢管壁厚局部环向腐蚀,进行了7个方钢管混凝土柱偏压试验,揭示了削弱率和偏心率对其偏压承载力的影响,并通过数值模拟对削弱率进行拓展分析.提出了基于削弱率的偏压承载力降低系数,代入中、美规范进行偏压承载力计算.结果表明:钢管的局部环向变厚度严重削弱了方钢管混凝土柱的偏压承载力和侧向挠曲能力;较大的加载偏心率也降低了其偏压承载力,但增大了其侧向挠曲能力.引入偏压承载力降低系数后,根据中、美规范计算得到的偏压承载力与试验值均吻合较好;相比于我国规范,美国规范在计算偏压承载力时相对更加保守.