ACPRs of leukopenia in peripheral blood of workers exposed to benzene in small-scale industries are calculated using capture-recapture methods. The results from two figures with 6-month apart demonstrate that the ACPR...ACPRs of leukopenia in peripheral blood of workers exposed to benzene in small-scale industries are calculated using capture-recapture methods. The results from two figures with 6-month apart demonstrate that the ACPR in workers exposed to benzene is 36.81(29. 14-44.48)%, significantly higher than that of control 12.71(7.20-18.22)% (P<0.05),with a relative risk of 2.9. The prevalences of 4 cross-sectional investigations in exposure group calculated with routine method are 18.73%, 26.37%, 27.93%, and 36.76% respectively;in controls, 8.38%, 6.85%, 7.94%, and 15.00% respectively and all fall in the range of 95% CI of ACPR. It is suggested that the methods of calculating ACPR by capture-recapture methods is simple, feasible and efficient, with the results more precise than with traditional methods.展开更多
In this paper, the ring-type ingot of hypereutectic high Cr cast iron was obtained by slope cooling bodycentrifugal casting method （SC-CCM）, and its microstructure and impact toughness were investigated, respectivel...In this paper, the ring-type ingot of hypereutectic high Cr cast iron was obtained by slope cooling bodycentrifugal casting method （SC-CCM）, and its microstructure and impact toughness were investigated, respectively. The results indicated that, first, the primary carbides in the microstructure are prominently finer than those in the hypereutectic high Cr cast iron prepared by conventional casting method. Second, in the ring-type ingot, the primary carbides near radial outer field are finer than those near radial inner field; furthermore, there is dividing field in the microstructure. Finally, the impact toughness values of the specimens impacted on the radial outer face and on the radial inner face are improved respectively about 36% and 138% more than that of the hypereutectic high Cr one prepared by conventional casting method.展开更多
A method combining theoretical analysis with experiment is adopted and the flowing process of Ti-48A1-2Cr-2Nb alloy melt poured in a permanent mould during the centrifugal casting process has been analyzed. A mathemat...A method combining theoretical analysis with experiment is adopted and the flowing process of Ti-48A1-2Cr-2Nb alloy melt poured in a permanent mould during the centrifugal casting process has been analyzed. A mathematical model of the filling process is established and the forming mechanism of internal gaseous defect is summarized. The results of calculation show that the melt fills the mould with varying cross-section area and inclined angle. The filling speed of the cross-section is a function of filling time. The cross-section area is directly proportional to the filling speed and the inclined angle is inversely proportional to the filling speed at a given rotating speed of the platform. Both of them changes more obvious near the mould entrance. The gaseous defect can be formed in several ways and the centrifugal field has an important influence on the formation of the defect. In addition, the filling process in centrifugal field has been verified by wax experiments and the theoretical analysis are consistent with experimental results.展开更多
A classic body composition method is estimation of total body skeletal muscle mass (SM, kg) from 24 h urinary creatinine excretion (Cr, g). Two types of prediction equations were suggested: one assumes a constant SM/C...A classic body composition method is estimation of total body skeletal muscle mass (SM, kg) from 24 h urinary creatinine excretion (Cr, g). Two types of prediction equations were suggested: one assumes a constant SM/Cr ratio; and the other assumes a highly variable SM/Cr ratio. We explored these two extreme possibilities by measuring SM with whole-body computerized axial tomography and collecting Cr during meat-free dietary conditions in 12 healthy young men. Prediction equations were developed in the men that fit these two equation types, SM = 21.8×Cr (SD and CV of SM/Cr ratio, 1.3 kg and 6.0%,respectively) and SM = 18.9 × Cr + 4.1 (r = 0.92, p = 2.55 × 10-5, and SEE = 1.9 kg). The validity of each model is reviewed. This is the first investigation of Cr-SM method using modern techniques for quantifying total body SM mass展开更多
Zinc sulfide photocatalysts doped with chromium (1:1)% were synthesized via precipitation technique. Their characteristics were studied by X-ray diffraction (XRD), AFM and Florescence spectrometer. The photocatalytic ...Zinc sulfide photocatalysts doped with chromium (1:1)% were synthesized via precipitation technique. Their characteristics were studied by X-ray diffraction (XRD), AFM and Florescence spectrometer. The photocatalytic reaction was applied under light intensity equal to 1.45 × 10-7 Einstein mol-1 to investigate the kinetics and thermodynamic parameters for photo-decolorization of reactive black 5 dye in collide solution of bare and Cr-doped ZnS. The mean crystal size and particle size for bare ZnS are more than those values for prepared Cr loaded ZnS.展开更多
Based on the current situation of studying the thermodynamic property of Fe-C-Cr melt using the carbon saturated solubility, an experimental data treatment method of the carbon saturated solubility was put forward. Wi...Based on the current situation of studying the thermodynamic property of Fe-C-Cr melt using the carbon saturated solubility, an experimental data treatment method of the carbon saturated solubility was put forward. With this method a linear relationship ex- pression of the carbon saturated solubility in Fe-C-Cr melt was obtained, which intercept is dependent on temperature and independent of third component [Cr], but which slope is dependent on third component [Cr] and independent of temperature. Through this expression activity interaction coefficients at different temperatures were calculated and the relationship between activity interaction coefficients and temperature is also obtained.展开更多
Purpose-The China-Europe Railway Express(CR Express)in Chongqing has operated regularly and undergone large-scale development.Its impact on Chongqing's economic growth has become increasingly evident,necessitating...Purpose-The China-Europe Railway Express(CR Express)in Chongqing has operated regularly and undergone large-scale development.Its impact on Chongqing's economic growth has become increasingly evident,necessitating further research in this field.Design/methodology/approach-This study employs the opening of CR Express as a quasi-natural experiment,designating Chongqing,which inaugurated the CR Express in 2011,as the treatment group.13 provinces and cities that had not yet opened the CR Express until 2017 were selected as the control group.Utilizing panel data from 14 provinces across China spanning from 2006 to 2017,the synthetic control method(SCM)is employed to synthetically construct Chongqing.To quantify the difference in economic development levels between Chongqing with the operation of the CR express and Chongqing without its operation.Key metrics such as gross domestic product(GDP),per capita GDP,total retail sales of consumer goods,import and export value and the proportions of the secondary and tertiary industries are employed to measure urban economic development capabilities.Chongqing is designated as the experimental group,and a double-difference model is constructed to regress the operation of the CR Express against economic development capabilities.Robustness tests are conducted to validate the analytical results.Findings-The results indicate that,compared to provinces without the operation of the CR Express,the initiation of the CR Express in Chongqing significantly enhances the economic development level of the city.The opening of the CR Express exhibits a pronounced positive impact on Chongqing's economic development,and these findings remain robust and effective even after parallel trend tests and placebo tests.Originalitylvalue-The study represents an expansion of the theoretical framework.In contrast to previous studies that relied on a single indicator such as GDP,this study selects six indicators from the dimensions of economy,trade and industry to measure regional economic development capabilities.Furthermore,employing the grey relational analysis method,the study screens these indicators,thereby providing a theoretical basis for the selection of indicators for measuring regional economic development capabilities.展开更多
The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-...The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-2.5 MPa. The experimental result reveals that the characteristic of two body abrasive wear and oxidation wear mechanisms are present for SiCn/2618 Al composite under higher load and sliding speed. SiC ceramic continuous network as the reinforcement can avoid composite from the third body wear that usually occurs in traditional particle reinforced composite. The mechanically mixed layer (MML) controls greatly the wear rate and friction coefficient of the composites. The composites tested at higher sliding speed exhibit higher value of friction coefficient and fluctuation, which is associated with the intermittent formation and removal of the MML. The wear and stress—strain behaviors of SiCn/Fe–40Cr against SiCn/Al 2168 at 30-105 m/s under 1.0-2.5 MPa were analyzed by finite element method with the software Solidwork2012 Simulation, respectively. The wear and stress–strain behavior of the composite predicted by the FEM correlated well with the experimental results.展开更多
文摘ACPRs of leukopenia in peripheral blood of workers exposed to benzene in small-scale industries are calculated using capture-recapture methods. The results from two figures with 6-month apart demonstrate that the ACPR in workers exposed to benzene is 36.81(29. 14-44.48)%, significantly higher than that of control 12.71(7.20-18.22)% (P<0.05),with a relative risk of 2.9. The prevalences of 4 cross-sectional investigations in exposure group calculated with routine method are 18.73%, 26.37%, 27.93%, and 36.76% respectively;in controls, 8.38%, 6.85%, 7.94%, and 15.00% respectively and all fall in the range of 95% CI of ACPR. It is suggested that the methods of calculating ACPR by capture-recapture methods is simple, feasible and efficient, with the results more precise than with traditional methods.
基金This work was supported by the National Natural Science Foundation of China under grant No.50571079.
文摘In this paper, the ring-type ingot of hypereutectic high Cr cast iron was obtained by slope cooling bodycentrifugal casting method （SC-CCM）, and its microstructure and impact toughness were investigated, respectively. The results indicated that, first, the primary carbides in the microstructure are prominently finer than those in the hypereutectic high Cr cast iron prepared by conventional casting method. Second, in the ring-type ingot, the primary carbides near radial outer field are finer than those near radial inner field; furthermore, there is dividing field in the microstructure. Finally, the impact toughness values of the specimens impacted on the radial outer face and on the radial inner face are improved respectively about 36% and 138% more than that of the hypereutectic high Cr one prepared by conventional casting method.
文摘A method combining theoretical analysis with experiment is adopted and the flowing process of Ti-48A1-2Cr-2Nb alloy melt poured in a permanent mould during the centrifugal casting process has been analyzed. A mathematical model of the filling process is established and the forming mechanism of internal gaseous defect is summarized. The results of calculation show that the melt fills the mould with varying cross-section area and inclined angle. The filling speed of the cross-section is a function of filling time. The cross-section area is directly proportional to the filling speed and the inclined angle is inversely proportional to the filling speed at a given rotating speed of the platform. Both of them changes more obvious near the mould entrance. The gaseous defect can be formed in several ways and the centrifugal field has an important influence on the formation of the defect. In addition, the filling process in centrifugal field has been verified by wax experiments and the theoretical analysis are consistent with experimental results.
文摘A classic body composition method is estimation of total body skeletal muscle mass (SM, kg) from 24 h urinary creatinine excretion (Cr, g). Two types of prediction equations were suggested: one assumes a constant SM/Cr ratio; and the other assumes a highly variable SM/Cr ratio. We explored these two extreme possibilities by measuring SM with whole-body computerized axial tomography and collecting Cr during meat-free dietary conditions in 12 healthy young men. Prediction equations were developed in the men that fit these two equation types, SM = 21.8×Cr (SD and CV of SM/Cr ratio, 1.3 kg and 6.0%,respectively) and SM = 18.9 × Cr + 4.1 (r = 0.92, p = 2.55 × 10-5, and SEE = 1.9 kg). The validity of each model is reviewed. This is the first investigation of Cr-SM method using modern techniques for quantifying total body SM mass
文摘Zinc sulfide photocatalysts doped with chromium (1:1)% were synthesized via precipitation technique. Their characteristics were studied by X-ray diffraction (XRD), AFM and Florescence spectrometer. The photocatalytic reaction was applied under light intensity equal to 1.45 × 10-7 Einstein mol-1 to investigate the kinetics and thermodynamic parameters for photo-decolorization of reactive black 5 dye in collide solution of bare and Cr-doped ZnS. The mean crystal size and particle size for bare ZnS are more than those values for prepared Cr loaded ZnS.
文摘Based on the current situation of studying the thermodynamic property of Fe-C-Cr melt using the carbon saturated solubility, an experimental data treatment method of the carbon saturated solubility was put forward. With this method a linear relationship ex- pression of the carbon saturated solubility in Fe-C-Cr melt was obtained, which intercept is dependent on temperature and independent of third component [Cr], but which slope is dependent on third component [Cr] and independent of temperature. Through this expression activity interaction coefficients at different temperatures were calculated and the relationship between activity interaction coefficients and temperature is also obtained.
文摘Purpose-The China-Europe Railway Express(CR Express)in Chongqing has operated regularly and undergone large-scale development.Its impact on Chongqing's economic growth has become increasingly evident,necessitating further research in this field.Design/methodology/approach-This study employs the opening of CR Express as a quasi-natural experiment,designating Chongqing,which inaugurated the CR Express in 2011,as the treatment group.13 provinces and cities that had not yet opened the CR Express until 2017 were selected as the control group.Utilizing panel data from 14 provinces across China spanning from 2006 to 2017,the synthetic control method(SCM)is employed to synthetically construct Chongqing.To quantify the difference in economic development levels between Chongqing with the operation of the CR express and Chongqing without its operation.Key metrics such as gross domestic product(GDP),per capita GDP,total retail sales of consumer goods,import and export value and the proportions of the secondary and tertiary industries are employed to measure urban economic development capabilities.Chongqing is designated as the experimental group,and a double-difference model is constructed to regress the operation of the CR Express against economic development capabilities.Robustness tests are conducted to validate the analytical results.Findings-The results indicate that,compared to provinces without the operation of the CR Express,the initiation of the CR Express in Chongqing significantly enhances the economic development level of the city.The opening of the CR Express exhibits a pronounced positive impact on Chongqing's economic development,and these findings remain robust and effective even after parallel trend tests and placebo tests.Originalitylvalue-The study represents an expansion of the theoretical framework.In contrast to previous studies that relied on a single indicator such as GDP,this study selects six indicators from the dimensions of economy,trade and industry to measure regional economic development capabilities.Furthermore,employing the grey relational analysis method,the study screens these indicators,thereby providing a theoretical basis for the selection of indicators for measuring regional economic development capabilities.
基金Project (2012BAE06B01) supported by the Key Technology R&D Program During the 12th Five-Year Plan Period, ChinaProjects(21201030, 51272039, 51032007) supported by the National Natural Science Foundation of ChinaProject (1099043) supported by the Science and Technology in Guangxi Province, China
文摘The dry friction and wear behaviors of co-continuous composites SiC/Fe–40Cr against SiC/Al 2618 alloy were investigated on a ring-on-ring friction and wear tester at sliding speed of 30-105 m/s under the load of 1.0-2.5 MPa. The experimental result reveals that the characteristic of two body abrasive wear and oxidation wear mechanisms are present for SiCn/2618 Al composite under higher load and sliding speed. SiC ceramic continuous network as the reinforcement can avoid composite from the third body wear that usually occurs in traditional particle reinforced composite. The mechanically mixed layer (MML) controls greatly the wear rate and friction coefficient of the composites. The composites tested at higher sliding speed exhibit higher value of friction coefficient and fluctuation, which is associated with the intermittent formation and removal of the MML. The wear and stress—strain behaviors of SiCn/Fe–40Cr against SiCn/Al 2168 at 30-105 m/s under 1.0-2.5 MPa were analyzed by finite element method with the software Solidwork2012 Simulation, respectively. The wear and stress–strain behavior of the composite predicted by the FEM correlated well with the experimental results.
