A series of activated carbons from Taixi anthracite were prepared by steam activation in the presence of KOH and then they were modified by different methods. The regulation of porosity and the modification of surface...A series of activated carbons from Taixi anthracite were prepared by steam activation in the presence of KOH and then they were modified by different methods. The regulation of porosity and the modification of surface chemistry were carried out with the aim to improve the benzene adsorption capacity of activated carbon. The influences of KOH and activation process parameters including activation temperature, activation time and steam flow rate on porosity of activated carbon were evaluated, and the effect of modification methods on surface chemistry was investigated. Also, the relationship between benzene adsorption capacity and porosity and surface chemistry was analyzed. Results show that activation temperature is the dominant factor in the activation process; the introduction of KOH into the raw material can enhance the reactivity of char in activation process, meanwhile it shows a negative effect on the porosity development, especially on the mesopore development. Results of FTIR analysis indicate that anthracite-based activated carbon with condensed aromatics and chemically inert oxygen does not present the nature to be surface modified. Besides, benzene adsorption capacity has an approximate linear relationship with surface area and in our preparation, benzene adsorption capacity and surface area of activated carbon are up to 1210 m 2 /g and 423 mg/g, respectively.展开更多
Commercial spherical activated carbon(SAC) was modified by impregnation to enhance the catalytic properties of SAC in acetylene hydrochlorination through melamine modification. Different modification conditions for ...Commercial spherical activated carbon(SAC) was modified by impregnation to enhance the catalytic properties of SAC in acetylene hydrochlorination through melamine modification. Different modification conditions for SAC with nitrogen were compared by changing the SAC-Melamine ratios. The effect of carbonization temperature on the modification was also investigated. Surface chemistry and adsorption properties of the modified and unmodified SACs were studied by scanning electron microscope(SEM), X-ray photoelectron spectroscopy(XPS), elementary analysis, BET, and temperature-programmed desorption(TPD). Moreover, the catalytic properties of SAC in acetylene hydrochlorination under differently modified conditions were also investigated. Elemental analysis showed that the nitrogen content of the modified SAC was greatly improved. XPS revealed that nitrogen mainly exists in Pyrrole nitrogen and Pyridine nitrogen. TPD showed that desorption of C2H2 was changed by modification. The conversion rate of acetylene was up to 70% under the following reaction conditions: temperature, 150 ℃; C2H2 hourly space velocity(GHSV), 36 h-1; feed volume ratio V(HCl)/V(C2H2) = 1.15. The catalytic properties of SAC were improved significantly via melamine modification.展开更多
Theoretical consideration was conducted on a relation between pore diameter and interfacialarea between pores and fibers when pores uniforinly distribute in C/C composites. It was shownthat bonding at the fiber/matrix...Theoretical consideration was conducted on a relation between pore diameter and interfacialarea between pores and fibers when pores uniforinly distribute in C/C composites. It was shownthat bonding at the fiber/matrix interface apparently decreased with decreasing a pore diameter,and consequently a new idea of microspace modification concept was proposed for controllingfracture behavior of C/C composites. Four types of C/C composites with various pore structureswere fabricated by hot-pressing, and their fracture behavior was investigated by three pointbending tests. The fracture behavior of the C/C composites was changed from brittle one topseudo ductile one with decreasing the pore diameter. This result supported the validity of themicrospace modification concept proposed in this paper.展开更多
Different oxygen and nitrogen containing functional groups were created on the surface of the multiwalled carbon nanotubes. The multi-walled carbon nanotubes were treated in ultrasonic bath with sulfuric or nitric aci...Different oxygen and nitrogen containing functional groups were created on the surface of the multiwalled carbon nanotubes. The multi-walled carbon nanotubes were treated in ultrasonic bath with sulfuric or nitric acid. Furthermore the surface texture was modified by increase of the roughness. In particular after treatment with the oxidizing nitric acid, in comparison to the H2SO4 or ultra-sonic treated samples,craters and edges are dominating the surface structures. Manganese oxide was deposited on the multiwalled carbon nanotubes by precipitation mechanism. Various manganese oxides are formed during the deposition process. The samples were characterized by elemental analysis, microscopy, thermal analysis,Raman spectroscopy, and by the zeta potential as well as X-ray diffraction measurements. It was shown that the deposited manganese oxides are stabilized rather by surface texture of the multi-walled carbon nanotubes than by created functional groups.展开更多
Silver coatings on the exterior surface of monolithic activated carbon(MAC) with different morphology were prepared by directly immersing MAC into [Ag(NH3)2]NO3 solution. Acid and base treatments were employed to ...Silver coatings on the exterior surface of monolithic activated carbon(MAC) with different morphology were prepared by directly immersing MAC into [Ag(NH3)2]NO3 solution. Acid and base treatments were employed to modify the surface oxygenic groups of MAC, respectively. The MACs' Brunauer-EmmettTeller(BET) surface area, surface groups, and silver coating morphology were characterized by N2 adsorption, elemental analysis(EA), X-ray photoelectron spectroscopy(XPS), and scanning electron microscopy(SEM), respectively. The coating morphology was found to be closely related to the surface area and surface functional groups of MAC. For a raw MAC which contained a variety of oxygenic groups, HNO3 treatment enhanced the relative amount of highly oxidized groups such as carboxyl and carbonates, which disfavored the deposition of silver particles. By contrast, Na OH treatment significantly improved the amount of carbonyl groups, which in turn improved the deposition amount of silver. Importantly, lamella silver was produced on raw MAC while Na OH treatment resulted in granular particles because of the capping effect of carbonyl groups. At appropriate [Ag(NH3)2]NO3 concentrations, silver nanoparticles smaller than 100 nm were homogeneously dispersed on Na OH-treated MAC. The successful tuning of the size and morphology of silver coatings on MAC is promising for novel applications in air purification and for antibacterial or aesthetic purposes.展开更多
The objective of the presented work was to assess the adsorption processes of Cu(Ⅱ) from aqueous solution onto a granular activated carbon (GAC) and a modified activated carbon (MAC) with nitric acid. Available surfa...The objective of the presented work was to assess the adsorption processes of Cu(Ⅱ) from aqueous solution onto a granular activated carbon (GAC) and a modified activated carbon (MAC) with nitric acid. Available surface functional groups, pH of the isoelectric point (pHIEP), and Fourier transform infrared spectroscopes were obtained to characterize the GAC/MAC. Factors influencing Cu(Ⅱ) adsorption such as adsorbent dosage, pH of solution, and contact time of the adsorption onto the MAC/GAC had been investigated in a batch experiment. Experimental equilibrium data had been obtained and modelled using both Freundlich and Langmuir classical adsorption isotherms and the data fitted better to Langmuir isotherm. It was found that nitric acid modification increased the Cu(Ⅱ) adsorption capacity to 90.9 mg/g, which was higher than the unmodified carbon by 41%. Two simplified models including pseudo-first-order and pseudo-second-order equations were selected to follow the adsorption processes.展开更多
Collagen fibers provide a good example of making strong micro-or mesoscale fibers from nanoscale tropocollagen molecules through a staggered and crosslinked organization in a bottom-up manner.Mimicking the architectur...Collagen fibers provide a good example of making strong micro-or mesoscale fibers from nanoscale tropocollagen molecules through a staggered and crosslinked organization in a bottom-up manner.Mimicking the architectural features of collagen fibers has been shown to be a promising approach to develop carbon nanotube(CNT)fibers of high performance.In the present work,an elastic model is developed to describe the load transfer and failure propagation within the bioinspired CNT bundles,and to establish the relations of the mechanical properties of the bundles with a number of geometrical and physical parameters such as the CNT aspect ratio and longitudinal gap,interface cross-link density,and the functionalizationinduced degradation in CNTs,etc.With the model,the stress distributions along the CNT-CNT interface as well as in every individual CNT are well captured,and the failure propagation along the interface and its effects on the mechanical properties of the CNT bundles are predicted.The work may provide useful guidelines for the design of novel CNT fibers in practice.展开更多
Manganese-based cathode materials are promising candidates for aqueous zinc ion batteries(AZIBs)by reason of their low cost and high energy density.However,their practical applicability is hampered by the intrinsic de...Manganese-based cathode materials are promising candidates for aqueous zinc ion batteries(AZIBs)by reason of their low cost and high energy density.However,their practical applicability is hampered by the intrinsic defects of poor electrical conductivity,sluggish reaction kinetics,and severe structural deterioration.Herein,we constructed a hierarchically porous structure composed of carbon-encapsulated Mn O nanoparticles(MOC)and three-dimensional(3D)nitrogen-doped graphene aerogel(NGA)(denoted as MOC@NGA).The hybrid was synthesized by a facile in-situ coprecipitation and annealing of manganesebased metal-organic framework(Mn-MOF74)and NGA composite(Mn-MOF74@NGA).Specifically,the carbon shells inherited from organic ligand of Mn-MOF74 could restrain the volume changes of Mn O,and the porous NGA prevented the agglomeration of MOC nanoparticles and enriched the types of interfacial chemical bonds.Profiting from the synergistic effect of rich interface chemical bonds and dual-carbon protection,the MOC@NGA hybrids exhibit fast interfacial electron/charge transfer and transport,and outstanding structural stability.Therefore,MOC@NGA cathode delivers an excellent rate performance(270 and 99.8 m Ah g^(-1)at 0.1 and 2.0 A g^(-1))and maintains an excellent specific capacity of 151.6 m Ah g^(-1)after 2,000cycles at 1.0 A g^(-1).Moreover,the fabricated MOC@NGA-based quasi-solid-state battery not only achieves outstanding flexibility but also displays impressive cycling stability,demonstrating a promising potential for portable and flexible equipment.This work provides a feasible strategy for the fabrication of the bridging structure of manganese-based oxides and porous carbon matrix for high-specific capacity and durable AZIBs cathodes.展开更多
A magnetic carbon composite, Fe3O4/C composite, was fabricated by one-step hydrothermal synthesis, modified by heat treatment under an inert atmosphere(N2), and then used as an adsorbent for ciprofloxacin(CIP) rem...A magnetic carbon composite, Fe3O4/C composite, was fabricated by one-step hydrothermal synthesis, modified by heat treatment under an inert atmosphere(N2), and then used as an adsorbent for ciprofloxacin(CIP) removal. Conditions for the modification were optimized according to the rate of CIP removal. The adsorbent was characterized by Fourier transform infrared spectroscopy, X-ray diffraction measurements, vibrating-sample magnetometry,scanning electron microscopy, transmission electron microscopy, and N2adsorption/desorption isotherm measurements. The results indicate that the modified adsorbent has substantial magnetism and has a large specific area, which favor CIP adsorption. The effects of solution p H, adsorbent dose, contact time, initial CIP concentration, ion strength, humic acid and solution temperature on CIP removal were also studied. Our results show that all of the above factors influence CIP removal. The Langmuir adsorption isotherm fits the adsorption process well, with the pseudo second-order model describing the adsorption kinetics accurately. The thermodynamic parameters indicate that adsorption is mainly physical adsorption. Recycling experiments revealed that the behavior of adsorbent is maintained after recycling for five times. Overall, the modified magnetic carbon composite is an efficient adsorbent for wastewater treatment.展开更多
A triethylene glycol modified glassy carbon electrode (TEG-GCE) was fabricated by a controlled- potential electrolysis procedure. The performance of the film on the modified electrode surface was investigated by cyc...A triethylene glycol modified glassy carbon electrode (TEG-GCE) was fabricated by a controlled- potential electrolysis procedure. The performance of the film on the modified electrode surface was investigated by cyclic voltammetry with different probes. It was firstly found that while neutral pieces could penetrate the TEG film on the GCE surface, the ionic pieces, whatever it is anion or cation, was blocked by the film. This property was successfully used for determining dopamine (DA) in the presence of ascorbic acid (AA) with differential pulse voltammetry (DPV).展开更多
基金the financial support by the Special Fund for Basic Scientific Research of Central Colleges (No.2009KH10)the Beijing Postdoctoral Fund (No. B148)the Green Shoots Plan of Beijing Academy of Science and Technology of China (No. B142)
文摘A series of activated carbons from Taixi anthracite were prepared by steam activation in the presence of KOH and then they were modified by different methods. The regulation of porosity and the modification of surface chemistry were carried out with the aim to improve the benzene adsorption capacity of activated carbon. The influences of KOH and activation process parameters including activation temperature, activation time and steam flow rate on porosity of activated carbon were evaluated, and the effect of modification methods on surface chemistry was investigated. Also, the relationship between benzene adsorption capacity and porosity and surface chemistry was analyzed. Results show that activation temperature is the dominant factor in the activation process; the introduction of KOH into the raw material can enhance the reactivity of char in activation process, meanwhile it shows a negative effect on the porosity development, especially on the mesopore development. Results of FTIR analysis indicate that anthracite-based activated carbon with condensed aromatics and chemically inert oxygen does not present the nature to be surface modified. Besides, benzene adsorption capacity has an approximate linear relationship with surface area and in our preparation, benzene adsorption capacity and surface area of activated carbon are up to 1210 m 2 /g and 423 mg/g, respectively.
基金Funded by the National Basic Research Program of China(973 Program,2012CB720302)the Program for Changjiang Scholars and Innovative Research Team in University(No.IRT1161)the Corps Science and Technology Innovation Team Scheme(2011CC001)
文摘Commercial spherical activated carbon(SAC) was modified by impregnation to enhance the catalytic properties of SAC in acetylene hydrochlorination through melamine modification. Different modification conditions for SAC with nitrogen were compared by changing the SAC-Melamine ratios. The effect of carbonization temperature on the modification was also investigated. Surface chemistry and adsorption properties of the modified and unmodified SACs were studied by scanning electron microscope(SEM), X-ray photoelectron spectroscopy(XPS), elementary analysis, BET, and temperature-programmed desorption(TPD). Moreover, the catalytic properties of SAC in acetylene hydrochlorination under differently modified conditions were also investigated. Elemental analysis showed that the nitrogen content of the modified SAC was greatly improved. XPS revealed that nitrogen mainly exists in Pyrrole nitrogen and Pyridine nitrogen. TPD showed that desorption of C2H2 was changed by modification. The conversion rate of acetylene was up to 70% under the following reaction conditions: temperature, 150 ℃; C2H2 hourly space velocity(GHSV), 36 h-1; feed volume ratio V(HCl)/V(C2H2) = 1.15. The catalytic properties of SAC were improved significantly via melamine modification.
文摘Theoretical consideration was conducted on a relation between pore diameter and interfacialarea between pores and fibers when pores uniforinly distribute in C/C composites. It was shownthat bonding at the fiber/matrix interface apparently decreased with decreasing a pore diameter,and consequently a new idea of microspace modification concept was proposed for controllingfracture behavior of C/C composites. Four types of C/C composites with various pore structureswere fabricated by hot-pressing, and their fracture behavior was investigated by three pointbending tests. The fracture behavior of the C/C composites was changed from brittle one topseudo ductile one with decreasing the pore diameter. This result supported the validity of themicrospace modification concept proposed in this paper.
文摘Different oxygen and nitrogen containing functional groups were created on the surface of the multiwalled carbon nanotubes. The multi-walled carbon nanotubes were treated in ultrasonic bath with sulfuric or nitric acid. Furthermore the surface texture was modified by increase of the roughness. In particular after treatment with the oxidizing nitric acid, in comparison to the H2SO4 or ultra-sonic treated samples,craters and edges are dominating the surface structures. Manganese oxide was deposited on the multiwalled carbon nanotubes by precipitation mechanism. Various manganese oxides are formed during the deposition process. The samples were characterized by elemental analysis, microscopy, thermal analysis,Raman spectroscopy, and by the zeta potential as well as X-ray diffraction measurements. It was shown that the deposited manganese oxides are stabilized rather by surface texture of the multi-walled carbon nanotubes than by created functional groups.
基金Funded by the Interdisciplinary Program of Shanghai Jiao Tong University(YG2016MS24)
文摘Silver coatings on the exterior surface of monolithic activated carbon(MAC) with different morphology were prepared by directly immersing MAC into [Ag(NH3)2]NO3 solution. Acid and base treatments were employed to modify the surface oxygenic groups of MAC, respectively. The MACs' Brunauer-EmmettTeller(BET) surface area, surface groups, and silver coating morphology were characterized by N2 adsorption, elemental analysis(EA), X-ray photoelectron spectroscopy(XPS), and scanning electron microscopy(SEM), respectively. The coating morphology was found to be closely related to the surface area and surface functional groups of MAC. For a raw MAC which contained a variety of oxygenic groups, HNO3 treatment enhanced the relative amount of highly oxidized groups such as carboxyl and carbonates, which disfavored the deposition of silver particles. By contrast, Na OH treatment significantly improved the amount of carbonyl groups, which in turn improved the deposition amount of silver. Importantly, lamella silver was produced on raw MAC while Na OH treatment resulted in granular particles because of the capping effect of carbonyl groups. At appropriate [Ag(NH3)2]NO3 concentrations, silver nanoparticles smaller than 100 nm were homogeneously dispersed on Na OH-treated MAC. The successful tuning of the size and morphology of silver coatings on MAC is promising for novel applications in air purification and for antibacterial or aesthetic purposes.
基金The Key Results Promotion of Jiangxi Province,China ( No. 2009CBB00800) Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense,China( No. 2010RGET15) Educational Committee of Jiangxi Province,China( No. GJJ12386)
文摘The objective of the presented work was to assess the adsorption processes of Cu(Ⅱ) from aqueous solution onto a granular activated carbon (GAC) and a modified activated carbon (MAC) with nitric acid. Available surface functional groups, pH of the isoelectric point (pHIEP), and Fourier transform infrared spectroscopes were obtained to characterize the GAC/MAC. Factors influencing Cu(Ⅱ) adsorption such as adsorbent dosage, pH of solution, and contact time of the adsorption onto the MAC/GAC had been investigated in a batch experiment. Experimental equilibrium data had been obtained and modelled using both Freundlich and Langmuir classical adsorption isotherms and the data fitted better to Langmuir isotherm. It was found that nitric acid modification increased the Cu(Ⅱ) adsorption capacity to 90.9 mg/g, which was higher than the unmodified carbon by 41%. Two simplified models including pseudo-first-order and pseudo-second-order equations were selected to follow the adsorption processes.
基金support from IHPC,A*STARpartially supported by the China Postdoctoral Science Foundation(Grant No.2014M562055)
文摘Collagen fibers provide a good example of making strong micro-or mesoscale fibers from nanoscale tropocollagen molecules through a staggered and crosslinked organization in a bottom-up manner.Mimicking the architectural features of collagen fibers has been shown to be a promising approach to develop carbon nanotube(CNT)fibers of high performance.In the present work,an elastic model is developed to describe the load transfer and failure propagation within the bioinspired CNT bundles,and to establish the relations of the mechanical properties of the bundles with a number of geometrical and physical parameters such as the CNT aspect ratio and longitudinal gap,interface cross-link density,and the functionalizationinduced degradation in CNTs,etc.With the model,the stress distributions along the CNT-CNT interface as well as in every individual CNT are well captured,and the failure propagation along the interface and its effects on the mechanical properties of the CNT bundles are predicted.The work may provide useful guidelines for the design of novel CNT fibers in practice.
基金supported by the National Natural Science Foundation of China(22271114,21621001)the Foundation of Science and Technology Development of Jilin Province,China(20200801004GH)+1 种基金111 Project(B17020)the financial support by the program for JLU Science and Technology Innovative Research Team(JLUSTIRT)。
文摘Manganese-based cathode materials are promising candidates for aqueous zinc ion batteries(AZIBs)by reason of their low cost and high energy density.However,their practical applicability is hampered by the intrinsic defects of poor electrical conductivity,sluggish reaction kinetics,and severe structural deterioration.Herein,we constructed a hierarchically porous structure composed of carbon-encapsulated Mn O nanoparticles(MOC)and three-dimensional(3D)nitrogen-doped graphene aerogel(NGA)(denoted as MOC@NGA).The hybrid was synthesized by a facile in-situ coprecipitation and annealing of manganesebased metal-organic framework(Mn-MOF74)and NGA composite(Mn-MOF74@NGA).Specifically,the carbon shells inherited from organic ligand of Mn-MOF74 could restrain the volume changes of Mn O,and the porous NGA prevented the agglomeration of MOC nanoparticles and enriched the types of interfacial chemical bonds.Profiting from the synergistic effect of rich interface chemical bonds and dual-carbon protection,the MOC@NGA hybrids exhibit fast interfacial electron/charge transfer and transport,and outstanding structural stability.Therefore,MOC@NGA cathode delivers an excellent rate performance(270 and 99.8 m Ah g^(-1)at 0.1 and 2.0 A g^(-1))and maintains an excellent specific capacity of 151.6 m Ah g^(-1)after 2,000cycles at 1.0 A g^(-1).Moreover,the fabricated MOC@NGA-based quasi-solid-state battery not only achieves outstanding flexibility but also displays impressive cycling stability,demonstrating a promising potential for portable and flexible equipment.This work provides a feasible strategy for the fabrication of the bridging structure of manganese-based oxides and porous carbon matrix for high-specific capacity and durable AZIBs cathodes.
基金supported by the National Natural Science Foundation of China (No. 21376159)the Natural Science Foundation of Shanxi Province (No. 2013011042-2)
文摘A magnetic carbon composite, Fe3O4/C composite, was fabricated by one-step hydrothermal synthesis, modified by heat treatment under an inert atmosphere(N2), and then used as an adsorbent for ciprofloxacin(CIP) removal. Conditions for the modification were optimized according to the rate of CIP removal. The adsorbent was characterized by Fourier transform infrared spectroscopy, X-ray diffraction measurements, vibrating-sample magnetometry,scanning electron microscopy, transmission electron microscopy, and N2adsorption/desorption isotherm measurements. The results indicate that the modified adsorbent has substantial magnetism and has a large specific area, which favor CIP adsorption. The effects of solution p H, adsorbent dose, contact time, initial CIP concentration, ion strength, humic acid and solution temperature on CIP removal were also studied. Our results show that all of the above factors influence CIP removal. The Langmuir adsorption isotherm fits the adsorption process well, with the pseudo second-order model describing the adsorption kinetics accurately. The thermodynamic parameters indicate that adsorption is mainly physical adsorption. Recycling experiments revealed that the behavior of adsorbent is maintained after recycling for five times. Overall, the modified magnetic carbon composite is an efficient adsorbent for wastewater treatment.
基金financially supported by the Natural Science Foundation of Hebei Province of China(No.B2010000844)Research Foundation of Education Department of Hebei Province of China(No.ZH2012078)
文摘A triethylene glycol modified glassy carbon electrode (TEG-GCE) was fabricated by a controlled- potential electrolysis procedure. The performance of the film on the modified electrode surface was investigated by cyclic voltammetry with different probes. It was firstly found that while neutral pieces could penetrate the TEG film on the GCE surface, the ionic pieces, whatever it is anion or cation, was blocked by the film. This property was successfully used for determining dopamine (DA) in the presence of ascorbic acid (AA) with differential pulse voltammetry (DPV).