针对成品油船货油装卸系统自动化、智能化研究中的关键技术问题,以45000dw t成品油船为研究背景,进行货油装卸系统的仿真研究。建立了基于计算机局域网的系统整体模型、系统故障检测模型、货油泵阀的数学模型、货油舱的数学模型及船体...针对成品油船货油装卸系统自动化、智能化研究中的关键技术问题,以45000dw t成品油船为研究背景,进行货油装卸系统的仿真研究。建立了基于计算机局域网的系统整体模型、系统故障检测模型、货油泵阀的数学模型、货油舱的数学模型及船体浮态模型,并用V isua l B as ic 6.0编制了货油装卸系统仿真软件。该软件具有系统自检、故障分析、故障报警及防止误操作等功能,实现了装油、卸油作业方案操作的自动化仿真。展开更多
As international maritime organization （IMO） draft 289 was adopted to develop a low-alloy anti-corrosion steel for the deck of cargo oil tank and to understand corrosion mechanism, corrosion behavior of a low-alloy ...As international maritime organization （IMO） draft 289 was adopted to develop a low-alloy anti-corrosion steel for the deck of cargo oil tank and to understand corrosion mechanism, corrosion behavior of a low-alloy steel with chromium contents was studied in O2-CO2-SO2-H2 S wet gas environment. Corrosion rate was measured, and the microstructure and morphology of corrosion product film were characterized by scanning electron microscopy （SEM）. The phase and chemical composition of the corrosion product film were investigated by X-ray diffraction （XRD） and energy dispersive spectroscopy （EDS）, respectively. The effect of misorientation distribution on corro- sion resistance of steel was evaluated by electron backscattered diffraction （EBSD）. The results showed that corro- sion rate decreased with increasing chromium content in the low-alloy steel, and the corrosion type was general corrosion. The phenomenon of chromium enrichment was found in corrosion product film consisting of a-FeOOH, γ- FeOOH, sulphur, FeS2 and Fel-xS. The increase of chromium content decreases the amount of high-angle grain boundaries, thus resulting in the improvement of corrosion resistance.展开更多
Corrosion behavior of low-alloy steel was investigated in simulated cargo oil tank （COT） bottom plate service environment （10% NaCl solution, pH = 0.85）. The corrosion behavior of inclusion was studied by in-situ ...Corrosion behavior of low-alloy steel was investigated in simulated cargo oil tank （COT） bottom plate service environment （10% NaCl solution, pH = 0.85）. The corrosion behavior of inclusion was studied by in-situ scanning electron microscopy （SEM） and energy dispersive spectroscopy （EDS）. It was found that pitting corrosion was inclined to occur around the place where inclusions exist. After initial corrosion, an area of 10-20μm in diameter was formed as a cireinate cathode around the edge of inclusion. MnS inclusion dissolved in the simulated COT corrosion solution before low-alloy steel matrix, and pitting was formed at the place where MnS dissolved. TiO2 inclusion dissolved in the simulated COT corrosion solution after low alloy steel matrix, and pitting was formed at the place where steel matrix dissolved. The corrosion tended to occur at the area where the curvature radius of inclusion is smaller. The size of round TiO2 inclusions had little influence on corrosion behavior in this certain environment.展开更多
E32 grade corrosion resistant steel was welded with welding wires with three different S contents. The mi crostructure, mechanical properties, inclusions, and corrosion behavior of welded joint were investigated. The ...E32 grade corrosion resistant steel was welded with welding wires with three different S contents. The mi crostructure, mechanical properties, inclusions, and corrosion behavior of welded joint were investigated. The joint coupon corrosion test and potentiodynamic polarization test were carried out under the simulated corrosion environ- ment of the inner bottom plates of cargo oil tanks. The pitting initiation and propagation mechanism of the weld metal were studied by scanning electron microscopy and infinite focus. The results indicated that the microstructures of three kinds of weld metals are all composed of acicular ferrite, ferrite side-plate and proeutectoid ferrite. The micro- structure of heat affected zone is composed predominantly of bainite. Joint welded with low S filler wire has good me- chanical properties. S can decrease free corrosion potential and increase the corrosion tendency. The pitting initiation is oxide inclusion or sulfide oxide inclusion complex. S can induce the formation of occluded area and promote the corrosion propagation. The chemical compositions of weld metal is similar to base metal, which can limit the galvanic corrosion between weld metal and base metal, and avoid formation of corrosion step.展开更多
A simulated corrosion test apparatus was used to investigate the corrosion behavior of a low alloy steel under simulated upper deck conditions in a cargo oil tank. The estimated corrosion loss of conventional E36 clas...A simulated corrosion test apparatus was used to investigate the corrosion behavior of a low alloy steel under simulated upper deck conditions in a cargo oil tank. The estimated corrosion loss of conventional E36 class ship plate steel is 4.27 mm, which is clearly inadequate compared with the standard adopted by International Maritime Organization. Outer rust layer of specimens starts to peel off after 77 days and becomes fragmented after 98 days. X-ray diffraction, scanning electron micros- copy, and Raman spectroscopy revealed that the resulting rust is composed of σ-FeOOH （the main protective phase）, Fe2O3, FeS, elemental S, and FeSO4. FeSO4 in the interface of the base and rust layer leads to localized corrosion. Elemental sulfur forms on the surface of σ-FeOOH, and the quantity and size thereof increase with increasing corrosion time. Furthermore, layered elemental sulfur promotes fracture and peels off the rust layer.展开更多
Based on the improved particle swarm optimization(PSO) algorithm,an optimization approach for the cargo oil tank design(COTD) is presented in this paper.The purpose is to design an optimal overall dimension of the car...Based on the improved particle swarm optimization(PSO) algorithm,an optimization approach for the cargo oil tank design(COTD) is presented in this paper.The purpose is to design an optimal overall dimension of the cargo oil tank(COT) under various kinds of constraints in the preliminary design stage.A non-linear programming model is built to simulate the optimization design,in which the requirements and rules for COTD are used as the constraints.Considering the distance between the inner shell and hull,a fuzzy constraint is used to express the feasibility degree of the double-hull configuration.In terms of the characteristic of COTD,the PSO algorithm is improved to solve this problem.A bivariate extremum strategy is presented to deal with the fuzzy constraint,by which the maximum and minimum cargo capacities are obtained simultaneously.Finally,the simulation demonstrates the feasibility and effectiveness of the proposed approach.展开更多
采用动态流体分析软件AFT Impulse建立通用型浮式生产储卸油装置(Floating Production Storage and Offloading,FPSO)货油管路系统,对管路进行稳态和瞬态分析,根据水锤产生机理对发生水锤效应的工况进行延长关闭时间、两阶段关闭和加调...采用动态流体分析软件AFT Impulse建立通用型浮式生产储卸油装置(Floating Production Storage and Offloading,FPSO)货油管路系统,对管路进行稳态和瞬态分析,根据水锤产生机理对发生水锤效应的工况进行延长关闭时间、两阶段关闭和加调压塔等3种优化方式以确保货油系统的安全性。结果表明,采用增加调压塔的优化方式更有效。展开更多
文摘针对成品油船货油装卸系统自动化、智能化研究中的关键技术问题,以45000dw t成品油船为研究背景,进行货油装卸系统的仿真研究。建立了基于计算机局域网的系统整体模型、系统故障检测模型、货油泵阀的数学模型、货油舱的数学模型及船体浮态模型,并用V isua l B as ic 6.0编制了货油装卸系统仿真软件。该软件具有系统自检、故障分析、故障报警及防止误操作等功能,实现了装油、卸油作业方案操作的自动化仿真。
基金Item Sponsored by National Science and Technology Major Project of the Ministry of Science and Technology of China(2011ZX05016-004)National Key Technology Research and Development Program of the Ministry of Science and Technology of China(2011BAE25B00)
文摘As international maritime organization （IMO） draft 289 was adopted to develop a low-alloy anti-corrosion steel for the deck of cargo oil tank and to understand corrosion mechanism, corrosion behavior of a low-alloy steel with chromium contents was studied in O2-CO2-SO2-H2 S wet gas environment. Corrosion rate was measured, and the microstructure and morphology of corrosion product film were characterized by scanning electron microscopy （SEM）. The phase and chemical composition of the corrosion product film were investigated by X-ray diffraction （XRD） and energy dispersive spectroscopy （EDS）, respectively. The effect of misorientation distribution on corro- sion resistance of steel was evaluated by electron backscattered diffraction （EBSD）. The results showed that corro- sion rate decreased with increasing chromium content in the low-alloy steel, and the corrosion type was general corrosion. The phenomenon of chromium enrichment was found in corrosion product film consisting of a-FeOOH, γ- FeOOH, sulphur, FeS2 and Fel-xS. The increase of chromium content decreases the amount of high-angle grain boundaries, thus resulting in the improvement of corrosion resistance.
基金Item Sponsored by National Science and Technology Major Project of the Ministry of Science and Technology of China(2011ZX05016-004)National Key Technology Research and Development Program of the Ministry of Science and Technology of China(2011BAE25B00)
文摘Corrosion behavior of low-alloy steel was investigated in simulated cargo oil tank （COT） bottom plate service environment （10% NaCl solution, pH = 0.85）. The corrosion behavior of inclusion was studied by in-situ scanning electron microscopy （SEM） and energy dispersive spectroscopy （EDS）. It was found that pitting corrosion was inclined to occur around the place where inclusions exist. After initial corrosion, an area of 10-20μm in diameter was formed as a cireinate cathode around the edge of inclusion. MnS inclusion dissolved in the simulated COT corrosion solution before low-alloy steel matrix, and pitting was formed at the place where MnS dissolved. TiO2 inclusion dissolved in the simulated COT corrosion solution after low alloy steel matrix, and pitting was formed at the place where steel matrix dissolved. The corrosion tended to occur at the area where the curvature radius of inclusion is smaller. The size of round TiO2 inclusions had little influence on corrosion behavior in this certain environment.
基金Sponsored by National Key Technology Research and Development Program of China(2011BAE25B01)
文摘E32 grade corrosion resistant steel was welded with welding wires with three different S contents. The mi crostructure, mechanical properties, inclusions, and corrosion behavior of welded joint were investigated. The joint coupon corrosion test and potentiodynamic polarization test were carried out under the simulated corrosion environ- ment of the inner bottom plates of cargo oil tanks. The pitting initiation and propagation mechanism of the weld metal were studied by scanning electron microscopy and infinite focus. The results indicated that the microstructures of three kinds of weld metals are all composed of acicular ferrite, ferrite side-plate and proeutectoid ferrite. The micro- structure of heat affected zone is composed predominantly of bainite. Joint welded with low S filler wire has good me- chanical properties. S can decrease free corrosion potential and increase the corrosion tendency. The pitting initiation is oxide inclusion or sulfide oxide inclusion complex. S can induce the formation of occluded area and promote the corrosion propagation. The chemical compositions of weld metal is similar to base metal, which can limit the galvanic corrosion between weld metal and base metal, and avoid formation of corrosion step.
文摘A simulated corrosion test apparatus was used to investigate the corrosion behavior of a low alloy steel under simulated upper deck conditions in a cargo oil tank. The estimated corrosion loss of conventional E36 class ship plate steel is 4.27 mm, which is clearly inadequate compared with the standard adopted by International Maritime Organization. Outer rust layer of specimens starts to peel off after 77 days and becomes fragmented after 98 days. X-ray diffraction, scanning electron micros- copy, and Raman spectroscopy revealed that the resulting rust is composed of σ-FeOOH （the main protective phase）, Fe2O3, FeS, elemental S, and FeSO4. FeSO4 in the interface of the base and rust layer leads to localized corrosion. Elemental sulfur forms on the surface of σ-FeOOH, and the quantity and size thereof increase with increasing corrosion time. Furthermore, layered elemental sulfur promotes fracture and peels off the rust layer.
基金the National Special Fund for Agro-scientific Research in the Public Interest(No.201003024)
文摘Based on the improved particle swarm optimization(PSO) algorithm,an optimization approach for the cargo oil tank design(COTD) is presented in this paper.The purpose is to design an optimal overall dimension of the cargo oil tank(COT) under various kinds of constraints in the preliminary design stage.A non-linear programming model is built to simulate the optimization design,in which the requirements and rules for COTD are used as the constraints.Considering the distance between the inner shell and hull,a fuzzy constraint is used to express the feasibility degree of the double-hull configuration.In terms of the characteristic of COTD,the PSO algorithm is improved to solve this problem.A bivariate extremum strategy is presented to deal with the fuzzy constraint,by which the maximum and minimum cargo capacities are obtained simultaneously.Finally,the simulation demonstrates the feasibility and effectiveness of the proposed approach.
文摘采用动态流体分析软件AFT Impulse建立通用型浮式生产储卸油装置(Floating Production Storage and Offloading,FPSO)货油管路系统,对管路进行稳态和瞬态分析,根据水锤产生机理对发生水锤效应的工况进行延长关闭时间、两阶段关闭和加调压塔等3种优化方式以确保货油系统的安全性。结果表明,采用增加调压塔的优化方式更有效。
