Influence of alkali metal doping on surface properties and catalytic activity/selectivity of CaO catalysts in oxidative coupling of methane

Surface properties （viz. surface area, basicity/base strength distribution, and crystal phases） of alkali metal doped CaO （alkali metal/Ca= 0.1 and 0.4） catalysts and their catalytic activity/selectivity in oxidative coupling of methane （OCM） to higher hydrocarbons at different reaction conditions （viz. temperature, 700 and 750 ℃; CH4/O2 ratio, 4.0 and 8.0 and space velocity, 5140-20550 cm^3 ·g^-1·h^-1） have been investigated. The influence of catalyst calcination temperature on the activity/selectivity has also been investigated. The surface properties （viz. surface area, basicity/base strength distribution） and catalytic activity/selectivity of the alkali metal doped CaO catalysts are strongly influenced by the alkali metal promoter and its concentration in the alkali metal doped CaO catalysts. An addition of alkali metal promoter to CaO results in a large decrease in the surface area but a large increase in the surface basicity （strong basic sites） and the C2＋ selectivity and yield of the catalysts in the OCM process. The activity and selectivity are strongly influenced by the catalyst calcination temperature. No direct relationship between surface basicity and catalytic activity/selectivity has been observed. Among the alkali metal doped CaO catalysts, Na-CaO （Na/Ca = 0.1, before calcination） catalyst （calcined at 750 ℃）, showed best performance （C2＋ selectivity of 68.8% with 24.7% methane conversion）, whereas the poorest performance was shown by the Rb-CaO catalyst in the OCM process.

High adsorption selectivity of activated carbon and carbon molecular sieve boosting CO_(2)/N_(2) and CH_(4)/N_(2) separation

Flue gas and coal bed methane are two important sources of greenhouse gases.Pressure swing adsorption process has a wide range of application in the field of gas separation,and the selection of adsorbent is crucial.In this regard,in order to assess the better adsorbent for separating CO_(2) from flue gas and CH_(4) from coal bed methane,adsorption isotherms of CO_(2),CH_(4) and N_(2) on activated carbon and carbon molecular sieve are measured at 303.15,318.15 and 333.15 K,and up to 250 kPa.The experimental data fit better with Langmuir 2 compared to Langmuir 3 and Langmuir-Freundlich models,and Clausius-Clapeyron equation was used to calculate the isosteric heat.Both the order of the adsorbed amount and the adsorption heat on the two adsorbents are CO_(2)>CH_(4)>N_(2).The adsorption kinetics are calculated by the pseudo-first kinetic model,and the order of adsorption rates on activated carbon is N_(2)-CH_(4)>CO_(2),while on carbon molecular sieve,it is CO_(2)-N_(2)>CH_(4).It is shown that relative molecular mass and adsorption heat are the primary effect on kinetics for activated carbon,while kinetic diameter is the main resistance factor for carbon molecular sieve.Moreover,the adsorption selectivity of CH_(4)/N_(2) and CO_(2)/N_(2) were estimated with the ideal adsorption solution theory,and carbon molecular sieve performed best at 318.15 K for both CO_(2) and CH_(4) separation.The study suggested that activated carbon is a better choice for separating flue gas and carbon molecular sieve can be a strong candidate for separating coal bed methane.

Cerium-tungsten oxides supported on activated red mud for the selective catalytic reduction of NO_(x)

Activated red mud(RM)has been proved to be a promising base material for the selective catalysis reduction(SCR)of NOx.The inherent low reducibility and acidity limited its low-temperature activity.In this work,molybdenum oxide,tungsten oxide,and cerium oxide were used to reconfigure the redox sites and acid sites of red mud based catalyst.When activated red mud was reconfigured by cerium-tungsten oxide(Ce-W@RM),the NOx conversion kept above 90%at 219-480℃.The existence of Ce^(3+)/Ce^(4+) redox electron pairs provided more surface adsorbed oxygen(O_(α)) and served as a redox cycle.Positive interactions between Ce,W species and Fe oxide in red mud occurred,which led to the formation of unsaturated chemical bond and promoted the activation of adsorbed NH_(3) species.WO_(3) and Ce_(2)(WO_(4))_(3)(formed by solid-state reaction between Ce and W species)could provide more Brønsted acid sites(W-O modes of WO_(3),W=O or W-O-W modes of Ce_(2)(WO_(4))_(3)).CeO_(2) species could provide more Lewis acid sites.The Langmuir-Hinshelwood(L-H)routes and Eley-Rideal(E-R)routes occurred in the low-temperature SCR reaction on the Ce-W@RM surface.NH_(4)^(+) species on Brønsted acid sites,NH_(3) species on Lewis acid sites,bidentate nitrate and bridging nitrate species were key active intermediates species.

Effect of samarium on the N_(2) selectivity of Sm_(x)Mn_(0.3-x)Ti catalysts during selective catalytic reduction of NO_(x) with NH_(3)

This work aims to study the improvement effect of Sm on Mn-based catalysts for selective catalytic reduction (SCR) of NO with NH3.A series of Sm_(x)Mn_(0.3-x)-xTi catalysts (x=0,0.1,0.15,0.2,and 0.3) were prepared by co-precipitation.Activity tests indicated that the Sm_(0.15)Mn_(0.15)Ti catalyst showed superior performances,with a NO conversion of 100%and N_(2)selectivity above 87%at 180–300℃.The characterizations showed that Sm doping suppressed the crystallization of TiO_(2)and Mn2O3phases and increased the specific surface area and acidity.In particular,the surface area increased from 152.2 m^(2)·g^(-1)for Mn0.3Ti to 241.7 m^(2)·g^(-1)for Sm_(0.15)Mn_(0.15)Ti.These effects contributed to the high catalytic activity.The X-ray photoelectron spectroscopy (XPS) results indicated that the relative atomic ratios of Sm^(3+)/Sm and Oβ/O of Sm_(0.15)Mn_(0.15)Ti were 76.77at%and 44.11at%,respectively.The presence of Sm contributed to an increase in surface-absorbed oxygen (Oβ) and a decrease in Mn^(4+)surface concentration,which improved the catalytic activity.In the results of hydrogen temperature-programmed reduction(H_(2)-TPR),the presence of Sm induced a higher reduction temperature and lower H_(2)consumption (0.3 mmol·g^(-1)) for the Sm_(0.15)Mn_(0.15)Ti catalyst compared to the Mn0.3Ti catalyst.The decrease in Mn^(4+)weakened the redox property of the catalysts and increased the N_(2)selectivity by suppressing N_(2)O formation from NH3oxidation and the nonselective catalytic reduction reaction.The in situ diffuse reflectance infrared Fourier transform spectra (DRIFTs) revealed that NH3-SCR of NO over the Sm_(0.15)Mn_(0.15)Ti catalyst mainly followed the Eley–Rideal mechanism.Sm doping increased surface-absorbed oxygen and weakened the redox property to improve the NO conversion and N_(2)selectivity of the Sm_(0.15)Mn_(0.15)Ti catalyst.

Catalytically active membranes for esterification:A review

Esterification is an important process in the food industry and can be carried out via homogeneous or heterogeneous catalysis.The homogeneous catalyst,despite providing high conversion,can cause corrosion in reactors,which is not observed with the use of heterogeneous catalysts.However,some of these catalysts require a high process temperature and may lose their catalytic activity with reuse.Thus,catalytic membranes have been proposed as a promising alternative.The combination of catalysis and separation in a single module provides greater conversion,reduction of excess reagents,compact industrial plant,making the process more efficient.Within this context,this work aims to present a literature review on the catalytic membrane for the synthesis of esters,improving the understanding of the production and development.This review examines the materials,catalysts used,and synthetic pathways.A comparison between the methods,as well as limitations and gaps in the literature,are highlighted.

Photothermal Catalytic Selective Oxidation of Isobutane to Methacrylic Acid over Keggin-Type Heteropolyacid

Thermal and photothermal catalytic selec-tive oxidation of isobutane to methacrylic acid(MAA)are comparatively studied over a keggin-type Cs2.9Cu0.34V0.49PMo12O40 het-eropolyacid acid.An introduction of light was observed to enhance both the i-C4H10 conversion and the MAA selectivity,and consequently the MAA formate rate,particularly at low temperatures.Characterization re-sults show that oxidation of methacrolein(MAL)to MAA is the rate-limiting step while UV light illumination promotes the oxidation ofσ-bonded MAL with OH groups toσ-bonded MAA on the catalyst surface.These results demonstrate a synergistic effect of thermal cataly-sis and photocatalysis in selective oxidation of isobutane to MAA,which suggests photother-mal catalysis as a promising strategy to catalyze the selective oxidation of higher hydrocar-bons at relative mild reaction conditions.

Fabrication of highly dispersed carbon doped Cu-based oxides as superior selective catalytic oxidation of ammonia catalysts via employing citric acid-modified carbon nanotubes doping CuAl-LDHs

In this work,the CuAl-LDO/c-CNTs catalyst was fabricated via in situ oriented assembly of layered-double hydroxides(LDHs)and citric acid-modified carbon nanotubes(c-CNTs)followed by annealing treatment,and evaluated in the selective catalytic oxidation(SCO)of NH_(3)to N_(2).The CuAl-LDO/c-CNTs catalyst presented better catalytic performance(98%NH_(3)conversion with nearly 90%N_(2)selectivity at 513 K)than other catalysts,such as CuAlO_(x)/CNTs,CuAlO_(x)/c-CNTs and CuAl-LDO/CNTs.Multiple characterizations were utilized to analyze the difference of physicochemical properties among four catalysts.XRD,TEM and XPS analyses manifested that CuO and Cu_(2)O nanoparticles dispersed well on the surface of the Cu Al-LDO/c-CNTs catalyst.Compared with other catalysts,larger specific surface area and better dispersion of CuAl-LDO/c-CNTs catalyst were conducive to the exposure of more active sites,thus improving the redox capacity of the active site and NH_(3)adsorption capacity.In-situ DRIFTS results revealed that the internal selective catalytic reduction(iSCR)mechanism was found over CuAl-LDO/c-CNTs catalyst.

One-pot synthesis of bimetallic CeCu-SAPO-34 for high-efficiency selective catalytic reduction of nitrogen oxides with NH_(3) at low temperature

NH_(3) selective catalytic reduction(SCR) has been widely recognized as a promising technique for reducing nitrogen oxides from diesel vehicle exhausts. High-efficiency SCR catalysts that could perform at low temperatures are essential to denitration. In this work, a series of bimetallic CeCu-SAPO-34 molecular sieves were synthesized by one-step hydrothermal method. The Ce Cu-SAPO-34 maintained good crystallinity and a regular hexahedron appearance of Cu-SAPO-34 after introducing Ce species, while exhibiting a higher specific surface area and pore volume. The as-prepared CeCu-SAPO-34 with 0.02%(mass) Ce constituent exhibited the best catalytic activity below 300℃ and a maximum NO_(x) conversion of 99% was attained;the NO_(x) removal rates of more than 68% and 94% were achieved at 150℃ and 200℃, respectively. And the introduction of cerium species in Cu-SAPO-34 improves the low-temperature hydrothermal stability of the catalyst towards NH_(3)-SCR reaction. Additionally, the introduced Ce species could enhance the formation of abundant weak Br?nsted acid centers and promote the synergistic effect between CuO grains and isolated Cu^(2+) to enhance the redox cycle, which benefit the NH_(3)-SCR reaction.This work provides a facile synthesis method of high-efficiency SCR denitration catalysts towards diesel vehicles exhaust treatment under low temperature.

The catalytic activity of transition metal oxide nanoparticles on thermal decomposition of ammonium perchlorate

The catalytic proficiency of three MONs for AP thermal decomposition was studied in this work.A chemical co-precipitation method was used for synthesis of MONs(CuZnO,CoZnO,and NiZnO)and their characterization carried out by utilizing XRD,FTIR,and SEM.The TGA/DSC technique was employed for the investigation of the catalytic proficiency of MONs on the AP.The DSC data were used for measuring activation energy of catalyzed AP by using Ozawa,Kissinger,and Starink method.The MONs were much sensitive for AP decomposition,and the performance of AP decomposition was further improved.Among all the MONs,the CuZnO exhibits higher catalytic action than others and decomposition temperature of AP is descending around 117℃ by CuZnO.The reduction in the activation energy was noticed after the incorporation of MONs in AP.

Preparation of SO_4^(2-)/TiO_2-WO_3 solid superacid and its catalytic activity in acetalation and ketaltion

SO_4^(2-)/TiO_2-WO_3 was prepared and its catalytic activity under differentsynthetic conditions was discussed with esterification of n-butanoic acid and n-butyl alcohol asprobing reaction. The optimum conditions are found that the mass fraction of H_2WO_4 used in thecompound is 12.5 percent, the calcination temperature is 580 deg C, the calcination time is 3 h, andthe soaked consistency of H_2SO_4 is 1.0 mol centre dot L^(-1). Then SO_4^(2-)/TiO_2-WO_3 wasapplied as the catalyst in the catalytic synthesis of eight similar important ketals and acetalsunder the optimum conditions and revealed high catalytic activity. On condition that the molar ratioof aldehyde/ketone to glycol is 1:1.5, the mass fraction of the catalyst used in the reactants is0.5 percent, and the reaction time is 1.0 h, the yields of ketals and acetals can reach 64.2percent-95.1 percent. Moreover, it can be easily recovered and reused.

Enhancement of bimetallic Fe-Mn/CNTs nano catalyst activity and product selectivity using microemulsion technique

Bimetallic Fe-Mn nano catalysts supported on carbon nanotubes(CNTs) were prepared using microemulsion technique with water-to-surfactant ratios of 0.4-1.6. The nano catalysts were extensively characterized by different methods and their activity and selectivity in Fischer-Tropsch synthesis(FTS) have been assessed in a fixed-bed microreactor. The physicochemical properties and performance of the nanocatalysts were compared with the catalyst prepared by impregnation method. Very narrow particle size distribution has been produced by the microemulsion technique at relatively high loading of active metal. TEM images showed that small metal nano particles in the range of 3–7 nm were not only confined inside the CNTs but also located on the outer surface of the CNTs. Using microemulsion technique with water to surfactant ratio of0.4 decreased the average iron particle sizes to 5.1 nm. The reduction percentage and dispersion percentage were almost doubled. Activity and selectivity were found to be dependent on the catalyst preparation method and average iron particle size. CO conversion and FTS rate increased from 49.1% to 71.0% and 0.144 to 0.289 gHC/(gcat h), respectively. While the WGS rate decreased from 0.097 to 0.056 gCO2/(gcat h). C5+liquid hydrocarbons selectivity decreased slightly and olefins selectivity almost doubled.

Theoretical Study on the Catalytic Activity and Sulfur Resistibility of Amorphous Alloy Ni-B-P

In the present paper, one hundred cluster models NinBP （n = 1-6） have been designed and studied by density functional theory （DFT） to get an insight into the local structure, catalytic properties and sulfur resistibility of amorphous alloy Ni-B-P. The configurations in triplet state are found more stable than those in the singlet state. It is found： that as the content of Ni in the clusters increases, the value of Fermi level in clusters fluctuated, which shows that the content of Ni can influence the Fermi level to a certain extent. Based on the Fermi level and DOS, we consider the activity of catalyst in hydrogenation reaction is the best in cluster Ni3BP. On the basis of the charge of clusters NinBP （n = 1 -6）, we conclude the amorphous alloy Ni-B-P with high Ni content has better sulfur resistibility and the best hydrogenation activity, strong sulfur resistibility appears in clusters Ni3BP, and the amorphous alloy Ni60B20P20 with similar proportion is expected to prepare in the future.

Phospholipase C from Pseudomonas aeruginosa and Bacillus cereus:characterization of catalytic activity

Objective:To study characteristics of phospholipases C(PLCs),their importance for producing microorganisms us well us the potential of their use for industrial purposes.Methods:PLC from Bacillus cereus(B.cereus) D101 was selected as an example of Gram-positive PLCs and PLC from Pseudomanas aeruginosa(P.aeruginosa) D183 of Gram-negative ones.Enzymes were partially purified by ammonium sulfate precipitation followed by membrane dialysis.Partially purified preparations were used to study effect of different factors on activities as well as in substrate specificity tests which were conducted using a turbidimetric assay method.Results:Maximum activity was at pH 7 and 8 and 40 ℃ for P.aeruginosa PLC,and pH 8-10 and 37 ℃ for B.cereus PLC.Both PLCs were inhibited by Pi at 5 mM or higher,whereas,PLC from B.cereus only was inhibited by EDTA.Activity of P.aeruginosa PLC was not affected by removing Zn^(2+) ions from reaction mixture or their replacement with Ca^(2+),Ba^(2+),Mg^(2+) or Mn^(2+)ions.Vis-a-vis,activity of B.cereus PLC was found to be metal ion dependent PLCs from both isolates were relatively thermostable and showed maximum affinity toward phosphatidylcholine.Sphingomyelin and phosphatidylethanolamine were not good substrates and phosphatidylinositol,phosphatidylserine,phosphatidylglycerol and cardiolipin could be considered nonsubstrates.Conclusions:Human body physiological conditions could favor activity of P.aeruginosa and B.cereus PLCs.These enzymes may participate in phosphate scavenging and virulence of producing isolates but not in autolysis.PLCs from both isolates are potential candidates for industrial use.

A new method to improve surface morphology of Ni-Fe-Mo-Co alloy electrode and its catalytic activity for HER

A new pretreatment method has been developed to improve the catalytic activity of the Ni-Fe-Mo-Co alloy electrode for hydrogen evolution reaction （HER）. The procedure involves pre-electrolyzing the Ni-Fe-Mo-Co alloy electrode in 30% KOH solution containing 10% potassium sodium tartrate at 70℃ for 2 h, until some of the Mo and Fe elements are leached out. The surface morphology of the Ni-Fe-Mo-Co alloy demonstrates a unique hive-like structure after the pre- treatment, which has the pore size in a nanometer range （about 50 nm）, a very large real surface area, and good stability. The results of the electrochemical studies show that compared to other similar electrode materials and the treated Ni-Fe-Mo-Co electrode by leaching method, the pre-treated Ni-Fe-Mo-Co electrode has a much lower overpotential and much higher exchange current density for HER. In addition, a long-term continuous electrolysis test with a current interruption shows that the Ni-Fe-Mo-Co alloy has excellent catalytic stability.

Synthesis, Crystal Structure and Catalytic Activity of a Pd-PEPPSI Complex Bearing Bromine Group

A new Pd-PEPPSI complex(2) with the bromo groups on the para-positions of N-aryl moieties of NHC has been synthesized and characterized by NMR and X-ray single-crystal diffraction. Complex 2 crystallizes in monoclinic, space group P2_1/c with a = 11.8790(8), b = 14.3038(10), c = 15.9905(11) ?, β = 101.291(2)°, V = 2664.4(3) ?3, Z = 4, D_c = 1.722 Mg/m^3, μ = 3.913 mm^(-1), F(000) = 1352, the final R = 0.0682 and wR = 0.1914 for 15113 observed reflections(I > 2σ(I)), R(all data) = 0.0970, w R(all data) = 0.2115, completeness to theta of 25.00 is 100.0% and GOOF = 1.035. Influenced by the electron-withdrawing bromo groups, the Pd-PEPPSI complex(2) showed high catalytic activity for the Suzuki-Miyaura cross-coupling reactions of aryl chlorides and arylboronic acids with a low catalyst loading(0.05 mol%) at room temperature in air.

Low-Temperature Denitrification Performance of Cu2O/Activated Carbon Catalysts for Selective Catalytic Reduction of NOx by CO

To improve the denitrification performance of carbon-based materials for sintering flue gas,we prepared a composite catalyst comprising coconut shell activated carbon(AC)modified by thermal oxidation air.The microstructure,the specific surface area,the pore volume,the crystal structure,and functional groups presented in the prepared Cu2O/AC catalysts were thoroughly characterized.By using scanning electron microscopy(SEM),nitrogen adsorption/desorption isotherms,Fourier-transform infrared(FTIR)spectroscopy and X-ray diffractometry(XRD),the effects of Cu2O loading and calcination temperature on Cu2O/AC catalysts were investigated at low temperature(150℃).The research shows that Cu on the Cu2O/AC catalyst is in the form of Cu2O with good crystalline performance and is spherical and uniformly dispersed on the AC surface.The loading of Cu2O increases the active sites and the specific surface area of the reaction gas contact,which is conducive to the rapid progress of the carbon monoxide selective catalytic reduction(CO-SCR)reaction.When the loading of Cu2O was 8%and the calcination temperature was 500℃,the removal rate of NOx facilitated by the Cu2O/AC catalyst reached 97.9%.These findings provide a theoretical basis for understanding the denitrification of sintering flue gas.

Size-dependent peroxidase-like catalytic activity of Fe_3O_4 nanoparticles

有三种不同尺寸的 Fe3O4 nanoparticles (NP ) 的象 Peroxidase 一样催化性质，由化学一起沉淀和大音阶的第五音鈥揼e l 方法综合了，被紫外鈥搗i s 光谱分析调查。由把 Fe3O4 NP 与 11， 20，和 150 nm 的平均直径作比较，我们发现催化活动与减少的 nanoparticle 尺寸增加。用反应产品和底层的反应水流描绘 Fe3O4 NP 的催化活动的电气化学的方法也被开发。

Effects of surface chemical properties of activated coke on selective catalytic reduction of NO with NH_3 over commercial coal-based activated coke

Surface chemical properties of typical commercial coal-based activated cokes were characterized by Xray photoelectron spectroscopy(XPS) and acid-base titration, and then the influence of surface chemical properties on catalytic performance of activated cokes of NO reduction with NH3 was investigated in a fixed-bed quartz micro reactor at 150 ℃. The results indicate that the selective catalytic reduction(SCR) activity of activated cokes with the increase of its surface acidic sites and oxygen content,obviously, a correlation between catalytic activity and surface acidic sites content by titration has higher linearity than catalytic activity and surface oxygen content by XPS. While basic sites content by acid-base titration have not correlation with SCR activity. It has been proposed that surface basic sites content measured by titration may not be on adjacent of acidic surface oxides and then cannot form of NO2-like species, thus the reaction of reduction of NO with NH3 have been retarded.

Carbon‐based metal‐free catalysts for electrochemical CO2 reduction: Activity, selectivity, and stability

Zero or negative emissions of carbon dioxide(CO2)is the need of the times,as inexorable rising and alarming levels of CO2 in the atmosphere lead to global warming and severe climate change.The electrochemical CO2 reduction(eCO2R)to value‐added fuels and chemicals by using renewable electricity provides a cleaner and more sustainable route with economic benefits,in which the key is to develop clean and economical electrocatalysts.Carbon‐based catalyst materials possess desirable properties such as high offset potential for H2 evolution and chemical stability at the negative applied potential.Although it is still challenging to achieve highly efficient carbon‐based catalysts,considerable efforts have been devoted to overcoming the low selectivity,activity,and stability.Here,we summarize and discuss the recent progress in carbon‐based metal‐free catalysts including carbon nanotubes,carbon nanofibers,carbon nanoribbons,graphene,carbon nitride,and diamonds with an emphasis on their activity,product selectivity,and stability.In addition,the key challenges and future potential approaches for efficient eCO2R to low carbon‐based fuels are highlighted.For a good understanding of the whole history of the development of eCO2R,the CO2 reduction reactions,principles,and techniques including the role of electrolytes,electrochemical cell design and evaluation,product selectivity,and structural composition are also discussed.The metal/metal oxides decorated with carbon‐based electrocatalysts are also summarized.We aim to provide insights for further development of carbon‐based metal‐free electrocatalysts for CO2 reduction from the perspective of both fundamental understanding and technological applications in the future.

Study on Hydrothermal Stability and Catalytic Activity of Al-SBA-15 Mesoporous Materials Prepared by Impregnation Method

The mesoporous Al-SBA-15 zeolite was obtained via impregnation of pure silica-based SBA-15 zeolite with aluminum nitrate.The Al-SBA-15 sample was calcined in air at 800 ℃ for 6 h and hydrothermally treated at near 100 ℃ for 120 h,respectively,and then the thermal and hydrothermal stability of Al-SBA-15 sample was investigated by X-ray diffractometry (XRD),scanning electron microscopy (SEM),transmission electron microscopy (TEM) and nitrogen adsorption and desorption techniques.The Al-SBA-15 sample was also studied by 27 Al nuclear magnetic resonance (27 Al NMR) and ammonia temperature programmed desorption (NH 3-TPD) techniques.In addition,the catalytic activity of Al-SBA-15 zeolite was investigated by the Friedel-Crafts reactions of 2,4-di-tert-butylphenol with cinnamyl alcohol.The test results showed that the thermal and hydrothermal stability of Al-SBA-15 zeolite was better than that of SBA-15 zeo-lite.The Al-SBA-15 zeolite sample prepared by impregnation method exhibits more framework aluminum species and Al-O-Si units.Therefore,the number of the surface hydroxyl groups was reduced,resulting in the stabilization of framework structure ofAl-SBA-15 zeolite.The aluminum species can form weak and medium-strong acid sites with catalytic activity.