Phase analysis for the coated surface with B 4C and Y 2O 3 of cemented carbide WC-20Co in vacuum-heating was carried out by high-temperature X-ray diffraction from ambient temperature to 1300 ℃. The results show t...Phase analysis for the coated surface with B 4C and Y 2O 3 of cemented carbide WC-20Co in vacuum-heating was carried out by high-temperature X-ray diffraction from ambient temperature to 1300 ℃. The results show that, the high-concentration active boron atoms are released from the boron-supply agent B 4C located on the alloy surface and diffused into the γ-phase, leading to forming the three-element boron-bearing compound W 2Co 21B 6 beside forming boron-bearing compounds on the blank surface. By contrast with boronising only, the element yttrium in boronization broadens the boronising temperature range during vacuum-sintering, catalyzes the decarbonisation decomposition of B 4C and promotes diffusion of active boron atoms into the bulk of WC-Co.展开更多
WC-Co nanocrystalline nitrogen-containing cemented carbides were prepared by vacuum sintering and low pressure sintering.The sintering processes of Cr_(2)(C,N)doped nano WC-Co powders were studied by using thermogravi...WC-Co nanocrystalline nitrogen-containing cemented carbides were prepared by vacuum sintering and low pressure sintering.The sintering processes of Cr_(2)(C,N)doped nano WC-Co powders were studied by using thermogravimetric analysis(TGA)and differential scanning calorimetry(DSC).The effect of sintering temperature on the microstructure and mechanical properties of nanocrystalline cemented carbide was studied by scanning electron microscope(SEM),high resolution transmission electron microscope(HRTEM)and mechanical property test.The results showed that the nano WC grains began to grow in the solid phase sintering stage.A high-performance nano-nitrogen-containing cemented carbide with uniform microstructure and good interfacial bonding can be obtained by increasing the sintering temperature to 1380℃.It has a transverse rupture strength(TRS)of 5057 MPa and a hardness of 1956 HV30.展开更多
The effects of ultrafine WC(WC_(UF),0.5μm) or W(1μm) and C(0.3μm)(W+C)_(UF) additives on the densification,microstructure and mechanical properties of coarse-grained cemented carbides were compared systematically.O...The effects of ultrafine WC(WC_(UF),0.5μm) or W(1μm) and C(0.3μm)(W+C)_(UF) additives on the densification,microstructure and mechanical properties of coarse-grained cemented carbides were compared systematically.Overall,the cemented carbides with WC_(UF)/(W+C)_(UF) additives are almost fully densification to be higher than 99%,and the average grain size is kept above 2.8μm.The WC_(UF) additive assists grains to(truncated)trigonal prism shape by two dimensional(2D) growth,whereas the(W+C)_(UF) additive assists grains to rounded shape by three dimensional(3D) growth,lowers WC contiguity and increases face-centered-cubic Co.The hardness and bending strength of(75WC_(C)-15WC_(UF))-10Co are 86.6 HRA and 2 272 MPa,respectively,both higher than those of(75WC_(C)-15(W+C)_(UF))-10Co,which could be ascribed to the enhanced densification and unblemished grains.However,the fracture toughness of the(75WC_(C)-15(W+C)_(UF))-10Co is 23.5 MPa·m^(1/2),higher than that of the(75WC_(C)-15WC_(UF))-10Co due to the uniform WC-Co structure and flexible binder phase.展开更多
This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of lo...This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of low carbon steel were processed firstly by laser cladding with Fe-based alloy powders and then by electrospark deposition with WC-SCo cemented carbide. It is shown that, for these two treatments, the electrospark coating possesses finer microstructure than the laser coating, and the thickness and surface hardness of the electrospark coating can be substantially increased.展开更多
Varying the morphology and the structure of γ-phase (Co-base Co-W-C solid solution) by means of altering the cooling rate and the preparing method of liquid sintered WC-Co cemented carbides samples, the mechanism of ...Varying the morphology and the structure of γ-phase (Co-base Co-W-C solid solution) by means of altering the cooling rate and the preparing method of liquid sintered WC-Co cemented carbides samples, the mechanism of fcc→hcp transformation of γ-phase in WC-Co alloy has been explored. The results show that, the cooling rate is an important affecting factor on fcc→hcp transformation of γ-phase and the fcc→hcp transformation is mainly a diffusive type when cooling WC-Co samples above room temperature展开更多
Two types of fatigue tests, a rotating bending fatigue test and a three- or four-point bending fatigue test, were carried out on a fine grained WC-Co cemented carbide to evaluate its fatigue crack growth behavior and ...Two types of fatigue tests, a rotating bending fatigue test and a three- or four-point bending fatigue test, were carried out on a fine grained WC-Co cemented carbide to evaluate its fatigue crack growth behavior and fatigue lifetime. From successive observations of the specimen surface during the fatigue process, it was revealed that most of the fatigue lifetime of the tested WC-Co cemented carbide was occupied with crack growth cycles. Using the basic equation of fracture mechanics, the relationship between the fatigue crack growth rate(da/dN) and the maximum stress intensity factor(Kmax) was derived. From this relation, both the values of the threshold intensity factor(Kth) and the fatigue fracture toughness(Kfc) of the material were determined. The fatigue lifetime of the WC-Co cemented carbide was estimated by analysis based on the modified linear elastic fracture mechanics approach. Good agreement between the estimated and experimental fatigue lifetimes was confirmed.展开更多
The relative density of WC-Co cemented carbides during spark plasma sintering(SPS) was analyzed.Based on the change in displacement of the ram in the SPS system,the relative densities in the sintering process can be...The relative density of WC-Co cemented carbides during spark plasma sintering(SPS) was analyzed.Based on the change in displacement of the ram in the SPS system,the relative densities in the sintering process can be achieved at different temperatures.The results indicated that densification of the samples started at near 900°C,the density rapidly reached its maximum at the increasing temperature stage,in which the temperature was lower than the sintering temperature of 1200°C,and most of the densification took place in the stage.Besides,the theoretical values were consistent with the experimental results.展开更多
Tianjin Institute of Hard Alloy,Tianjin 300222,China ABSTRACT The effects of solutes of wolfram and carbon on specific saturation magnetization(4πσ)of cobalt have been examined on the basis of the measurement of Ana...Tianjin Institute of Hard Alloy,Tianjin 300222,China ABSTRACT The effects of solutes of wolfram and carbon on specific saturation magnetization(4πσ)of cobalt have been examined on the basis of the measurement of Ana for hexagonal typeα-Co and cubic typeβ-Co.The Co-W-C solid solution simulative alloys have been fabricated according to binder composition in WC-Co cemented carbides and the effect of its component and structure on its Ana has been discussed too.It is pointed out that the Co phase structural factor must be considered as measuring the Ana of WC-Co cemented carbides.展开更多
The sintering characteristics, microstructure, and mechanical properties of ultrafine WC-12%Co-0.2%VC/0.5%Cr3C2 cemented carbides were investigated. Dilatometric and differential thermal analyses (DTA) indicate that...The sintering characteristics, microstructure, and mechanical properties of ultrafine WC-12%Co-0.2%VC/0.5%Cr3C2 cemented carbides were investigated. Dilatometric and differential thermal analyses (DTA) indicate that the compacts start to shrink at 600°C, the shrinkage rate peak is at 1190°C, and the liquid formation temperature is lower than the W-C-Co eutectic temperature (1330°C). Microstructure analysis results show that the cemented carbides with fine and homogeneous microstructure were obtained when sintered at 1430°C. Continuous and discontinuous grain growth was suppressed due to the synergistic action of VC/Cr3C2. The transverse rupture strength (TRS) of the samples reaches 4286 MPa, with the hardness HRA 92.1. The fine and homogeneous microstructure, alloy strengthening, and different phase constitutions of binder in the cemented carbides result in high hardness and TRS. Continuous and discontinuous grain growth was observed in the cemented carbide sintered at 1450°C, which results in significant decreases of hardness and TRS. It indicates that VC/Cr3C2 additions in the cemented carbides can only suppress the grain growth at a certain temperature.展开更多
The tungsten-inert-gas (TIG) arc welding experiments of cemented carbide YG30 and steel 45 were carried out using the Ni-Fe-C filling alloys. The eta phases and mechanical properties of welded joints were analyzed by ...The tungsten-inert-gas (TIG) arc welding experiments of cemented carbide YG30 and steel 45 were carried out using the Ni-Fe-C filling alloys. The eta phases and mechanical properties of welded joints were analyzed by means of scanning electronic microscope (SEM), transmission electronic microscope (TEM) coupled with selected diffraction, electronic probe microanalysis and bending strength methods. The experimental results show that the chemical composition of the filling alloys affects eta phase formation. When the carbon and nickel contents in filling alloys are 0.61 wt% and 55.29 wt%, respectively, no eta phases form. And the joint bending strength is the highest to 1.352 GPa. But if they are 0.01wt% and 55.38wt%, the eta phases are formed at the boundaries of the cemented carbide and the weld, and the thickness of eta phase layer is about 110 micrometers. And the joint bending strength is low. Usually, these eta phases are anomalously granular, and easy to accumulate at the boundaries between cemented carbides and the weld. They are multiple M_6C rich in tungsten and iron.展开更多
The influence of γ-phase composition in WC-Co cemented carbides on its specific coercive force H_(sc) hasbeen studied by analysing the imitative alloys of γ-phase. The results show that the H_(sc) of γ-phase is low...The influence of γ-phase composition in WC-Co cemented carbides on its specific coercive force H_(sc) hasbeen studied by analysing the imitative alloys of γ-phase. The results show that the H_(sc) of γ-phase is lower thanthat of pure cobalt, because the solute W can raise γ-phase H_(sc) but the carbon exhibits more intense negativeeffect on H_(sc). The effect is enhanced with raising the C solubilities in γ-phase.展开更多
The allotropic transformation process of the γ-phase in WC-Co cemented carbides has been explored.Theconcepts of γ-grain and the γ-domain have been proposed forward:The γ-domain is the residual FCC-typeβ-Co grain...The allotropic transformation process of the γ-phase in WC-Co cemented carbides has been explored.Theconcepts of γ-grain and the γ-domain have been proposed forward:The γ-domain is the residual FCC-typeβ-Co grain that failed to transform when cooling alloy sample and γ-base is the HCP-type x-Co transformedmainly by means of diffusion,the outline of the γ-grain is consistent with the newly fromed β-Co grain formedat high temperature.The quantity and distribution of γ-grain domain are related to the cooling rate after sinter-ing and influence the alloys properties.展开更多
In order to optimize the tool coating material and reduce the tool wear rate,the coating material and wear mechanism for carbide tools are proposed and analyzed based on thermodynamics theory.We deduced the Gibbs free...In order to optimize the tool coating material and reduce the tool wear rate,the coating material and wear mechanism for carbide tools are proposed and analyzed based on thermodynamics theory.We deduced the Gibbs free energy function method and analyzed the enthalpy value of the coating material of cemented carbide tools.The rules of diffusion wear and oxidation wear for WC-Co-based carbide tools were analyzed based on the diffusion dissolution theory and the calculation method of the thermal effect of chemical reaction.The diffusion wear and oxidation wear of WC-Co-based carbide tools when machining Ti-6Al-4V were studied with SEM-EDS.The results indicate that a good prediction accuracy of both diffusion wear and oxidation wear can be achieved by the method of thermodynamic theory analysis method.The conclusion will provide useful references for the optimization of cutting parameters and the improvement of the tool life.展开更多
The effects of deep cryogenic treatment on the microstructure and properties of WC-11 Co cemented carbides with various carbon contents were investigated.The results show that after deep cryogenic treatment,WC grains ...The effects of deep cryogenic treatment on the microstructure and properties of WC-11 Co cemented carbides with various carbon contents were investigated.The results show that after deep cryogenic treatment,WC grains are refined into triangular prism with sound edges via the process of spheroidization,but WC grain size has no evident change compared with that of untreated alloys.The phase transformation of Co phase from α-Co(FCC) to ε-Co(HCP) is observed in the cryogenically treated alloys,which is attributed to the decrease of W solubility in the binder(Co).Deep cryogenic treatment enhances the hardness and bending strength of the alloys,while it has no significant effects on the density and cobalt magnetic performance.展开更多
The morphologies and formation process of Ni-pool defects in WC?8Ni cemented carbides were studied. The SEM images show that Ni-pool generally has two kinds of morphologies: “island” in isolation and “ring” around...The morphologies and formation process of Ni-pool defects in WC?8Ni cemented carbides were studied. The SEM images show that Ni-pool generally has two kinds of morphologies: “island” in isolation and “ring” around a new phase. In the obtained samples with “ring-like Ni-pool”, WC, Ni and Ni2W4C (η phase) phases were detected in XRD patterns. Combined with SEM, EDX and XRD results, it is found that the phase in the center of the “ring-like Ni-pool” is Ni2W4C (η phase) and the main chemical components of Ni-pool are Ni, W and C. In addition, the relationships among large size Ni (agglomerated) particles, volatile impurities, pores and carbon content vs forming process of the Ni-pool defects for WC?8Ni cemented carbides are also presented and discussed.展开更多
A new cup-type grinding wheel of the brazed monolayer diamond is developed with a defined grain pattern on the wheel surface. Grinding performance of the brazed wheel in the surface grinding of cemented carbide is stu...A new cup-type grinding wheel of the brazed monolayer diamond is developed with a defined grain pattern on the wheel surface. Grinding performance of the brazed wheel in the surface grinding of cemented carbide is studied. Experimental results show that when continuous dry grinding is employed, grits of the brazed diamond grinding wheel fail mainly in attritious wear and fracture modes and no pull-out ones are found in conventional electroplated and sintered diamond wheels. It indicates the strong retention of brazing alloy to diamond grits and the longer service life of the wheel. In addition, the ground surface has good roughness. The theoretical surface roughness agrees well with experimental results.展开更多
Nanocrystalline tungsten carbide-cobalt (WC-Co) composite powders produced through spray thermal decomposition-continuous reduction and carburization technology were used to prepare φ3.25 mm×38 mm ultrafine tung...Nanocrystalline tungsten carbide-cobalt (WC-Co) composite powders produced through spray thermal decomposition-continuous reduction and carburization technology were used to prepare φ3.25 mm×38 mm ultrafine tungsten carbide-cobalt (WC-Co) cemented carbide rods through vacuum sintering plus sinterhip technology. The microstructure, Vickers hardness, density and Rockwell A hardness (HRA), transverse rupture strength (TRS), saturated magnetization and coercivity force were tested. The results show that the average grain size of the sintering body prepared through vacuum sintering plus sinterhip technology was 430 nm; transverse rupture strength (TRS) was 3850 MPa; Vickers hardness was 1890 and Rockwell A hardness of sintering body was 93. High strength and high hardness ultrafine WC-Co cemented carbide rods used to manufacture printed circuit board (PCB) drills were obtained.展开更多
Coarse grained WC-9Co cemented carbides with 0-1.0% TaC(mass fraction) were fabricated by HIP-sintering and gas quenching. The effects of TaC on the microstructures and mechanical properties were investigated using sc...Coarse grained WC-9Co cemented carbides with 0-1.0% TaC(mass fraction) were fabricated by HIP-sintering and gas quenching. The effects of TaC on the microstructures and mechanical properties were investigated using scanning electron microscopy(SEM), energy dispersive X-ray analysis(EDS), X-ray diffractometry(XRD) and mechanical properties tests. The results show that the maximum values of hardness and strength are HV 1124 and 2466 MPa respectively when 0.4% TaC is added. When the content of TaC is more than 0.6%, the grain size of WC is no longer affected by the amount of TaC, and(W,Ta)C occurs as well. Moreover, the strength and fracture toughness increase and the(Ta+W) content decreases with the increase of TaC content. The dependence of(Ta+W) content on the mechanical properties indicates that(Ta+W) content in Co should be decreased as low as possible to improve the mechanical properties of coarse grained WC-TaC-9Co cemented carbides with the microstructure of WC+γ two phase regions.展开更多
Aim To research on a solid cemented carbide multi facet drill for drilling high strength steel. Methods Assimilating some features of multi facet drill edge structures, through systematic drilling experiments, a n...Aim To research on a solid cemented carbide multi facet drill for drilling high strength steel. Methods Assimilating some features of multi facet drill edge structures, through systematic drilling experiments, a new type of solid cemented carbide drill was developed and the drill geometry was optimized. Results With the new type drill,the drilling force decreases by 10%-20%, the drilling productivity (drilled holes per hour) increases by 2-3 times, and the drilling precision and surface finish increase by one level. Conclusion The new type drill possesses excellent drilling performance.展开更多
Finite dement formulations are used to simulate the evolution of the elastoplastic response of functionally graded cemented carbides (FGCC) due to thermal loading. The geometry of specimens is an axisymmetric solid ...Finite dement formulations are used to simulate the evolution of the elastoplastic response of functionally graded cemented carbides (FGCC) due to thermal loading. The geometry of specimens is an axisymmetric solid cylinder with a two-dimensional gradient. The elastoplastic constitutive relationship is developed by constraint factors. Numerical results show that compressive stresses occur in the surface zone and tensile stresses in the cobalt rich zone when the temperature drops from the initial stress-free temperature of 800 to 0℃. The maximum value of the surface compressive stress is 254 MPa and the maximum value of the tensile stress is 252 MPa in the cobalt rich zones. When the cobalt concentration difference in the specimens is equal to or greater than 0.3, there is pronounced plastic flow in cobalt rich zone. When the temperature heats up from 0 to 800 ℃, the total plastic strain reaches 0.001 4. Plastic flow has a significant effect on the reduction of thermal stress concentration.展开更多
文摘Phase analysis for the coated surface with B 4C and Y 2O 3 of cemented carbide WC-20Co in vacuum-heating was carried out by high-temperature X-ray diffraction from ambient temperature to 1300 ℃. The results show that, the high-concentration active boron atoms are released from the boron-supply agent B 4C located on the alloy surface and diffused into the γ-phase, leading to forming the three-element boron-bearing compound W 2Co 21B 6 beside forming boron-bearing compounds on the blank surface. By contrast with boronising only, the element yttrium in boronization broadens the boronising temperature range during vacuum-sintering, catalyzes the decarbonisation decomposition of B 4C and promotes diffusion of active boron atoms into the bulk of WC-Co.
基金Funded by the National Key Research and Development Plan of China(No.2017YFB0305900)。
文摘WC-Co nanocrystalline nitrogen-containing cemented carbides were prepared by vacuum sintering and low pressure sintering.The sintering processes of Cr_(2)(C,N)doped nano WC-Co powders were studied by using thermogravimetric analysis(TGA)and differential scanning calorimetry(DSC).The effect of sintering temperature on the microstructure and mechanical properties of nanocrystalline cemented carbide was studied by scanning electron microscope(SEM),high resolution transmission electron microscope(HRTEM)and mechanical property test.The results showed that the nano WC grains began to grow in the solid phase sintering stage.A high-performance nano-nitrogen-containing cemented carbide with uniform microstructure and good interfacial bonding can be obtained by increasing the sintering temperature to 1380℃.It has a transverse rupture strength(TRS)of 5057 MPa and a hardness of 1956 HV30.
基金Funded by the Technology Innovation Leading Program of Shaanxi(No.2022QFY08-02)。
文摘The effects of ultrafine WC(WC_(UF),0.5μm) or W(1μm) and C(0.3μm)(W+C)_(UF) additives on the densification,microstructure and mechanical properties of coarse-grained cemented carbides were compared systematically.Overall,the cemented carbides with WC_(UF)/(W+C)_(UF) additives are almost fully densification to be higher than 99%,and the average grain size is kept above 2.8μm.The WC_(UF) additive assists grains to(truncated)trigonal prism shape by two dimensional(2D) growth,whereas the(W+C)_(UF) additive assists grains to rounded shape by three dimensional(3D) growth,lowers WC contiguity and increases face-centered-cubic Co.The hardness and bending strength of(75WC_(C)-15WC_(UF))-10Co are 86.6 HRA and 2 272 MPa,respectively,both higher than those of(75WC_(C)-15(W+C)_(UF))-10Co,which could be ascribed to the enhanced densification and unblemished grains.However,the fracture toughness of the(75WC_(C)-15(W+C)_(UF))-10Co is 23.5 MPa·m^(1/2),higher than that of the(75WC_(C)-15WC_(UF))-10Co due to the uniform WC-Co structure and flexible binder phase.
文摘This paper presents the results of a study concerned with the surface hardening of Fe-based alloys and WC-8Co cemented carbide by inte- grating laser cladding and the electrospark deposition processes. Specimens of low carbon steel were processed firstly by laser cladding with Fe-based alloy powders and then by electrospark deposition with WC-SCo cemented carbide. It is shown that, for these two treatments, the electrospark coating possesses finer microstructure than the laser coating, and the thickness and surface hardness of the electrospark coating can be substantially increased.
文摘Varying the morphology and the structure of γ-phase (Co-base Co-W-C solid solution) by means of altering the cooling rate and the preparing method of liquid sintered WC-Co cemented carbides samples, the mechanism of fcc→hcp transformation of γ-phase in WC-Co alloy has been explored. The results show that, the cooling rate is an important affecting factor on fcc→hcp transformation of γ-phase and the fcc→hcp transformation is mainly a diffusive type when cooling WC-Co samples above room temperature
文摘Two types of fatigue tests, a rotating bending fatigue test and a three- or four-point bending fatigue test, were carried out on a fine grained WC-Co cemented carbide to evaluate its fatigue crack growth behavior and fatigue lifetime. From successive observations of the specimen surface during the fatigue process, it was revealed that most of the fatigue lifetime of the tested WC-Co cemented carbide was occupied with crack growth cycles. Using the basic equation of fracture mechanics, the relationship between the fatigue crack growth rate(da/dN) and the maximum stress intensity factor(Kmax) was derived. From this relation, both the values of the threshold intensity factor(Kth) and the fatigue fracture toughness(Kfc) of the material were determined. The fatigue lifetime of the WC-Co cemented carbide was estimated by analysis based on the modified linear elastic fracture mechanics approach. Good agreement between the estimated and experimental fatigue lifetimes was confirmed.
文摘The relative density of WC-Co cemented carbides during spark plasma sintering(SPS) was analyzed.Based on the change in displacement of the ram in the SPS system,the relative densities in the sintering process can be achieved at different temperatures.The results indicated that densification of the samples started at near 900°C,the density rapidly reached its maximum at the increasing temperature stage,in which the temperature was lower than the sintering temperature of 1200°C,and most of the densification took place in the stage.Besides,the theoretical values were consistent with the experimental results.
文摘Tianjin Institute of Hard Alloy,Tianjin 300222,China ABSTRACT The effects of solutes of wolfram and carbon on specific saturation magnetization(4πσ)of cobalt have been examined on the basis of the measurement of Ana for hexagonal typeα-Co and cubic typeβ-Co.The Co-W-C solid solution simulative alloys have been fabricated according to binder composition in WC-Co cemented carbides and the effect of its component and structure on its Ana has been discussed too.It is pointed out that the Co phase structural factor must be considered as measuring the Ana of WC-Co cemented carbides.
基金supported by the Foundation of Scientific and Technologic Development for Universityin Tianjin (No. 20060912)
文摘The sintering characteristics, microstructure, and mechanical properties of ultrafine WC-12%Co-0.2%VC/0.5%Cr3C2 cemented carbides were investigated. Dilatometric and differential thermal analyses (DTA) indicate that the compacts start to shrink at 600°C, the shrinkage rate peak is at 1190°C, and the liquid formation temperature is lower than the W-C-Co eutectic temperature (1330°C). Microstructure analysis results show that the cemented carbides with fine and homogeneous microstructure were obtained when sintered at 1430°C. Continuous and discontinuous grain growth was suppressed due to the synergistic action of VC/Cr3C2. The transverse rupture strength (TRS) of the samples reaches 4286 MPa, with the hardness HRA 92.1. The fine and homogeneous microstructure, alloy strengthening, and different phase constitutions of binder in the cemented carbides result in high hardness and TRS. Continuous and discontinuous grain growth was observed in the cemented carbide sintered at 1450°C, which results in significant decreases of hardness and TRS. It indicates that VC/Cr3C2 additions in the cemented carbides can only suppress the grain growth at a certain temperature.
基金financial supports from plan program of Dalian(grants No.2001145)
文摘The tungsten-inert-gas (TIG) arc welding experiments of cemented carbide YG30 and steel 45 were carried out using the Ni-Fe-C filling alloys. The eta phases and mechanical properties of welded joints were analyzed by means of scanning electronic microscope (SEM), transmission electronic microscope (TEM) coupled with selected diffraction, electronic probe microanalysis and bending strength methods. The experimental results show that the chemical composition of the filling alloys affects eta phase formation. When the carbon and nickel contents in filling alloys are 0.61 wt% and 55.29 wt%, respectively, no eta phases form. And the joint bending strength is the highest to 1.352 GPa. But if they are 0.01wt% and 55.38wt%, the eta phases are formed at the boundaries of the cemented carbide and the weld, and the thickness of eta phase layer is about 110 micrometers. And the joint bending strength is low. Usually, these eta phases are anomalously granular, and easy to accumulate at the boundaries between cemented carbides and the weld. They are multiple M_6C rich in tungsten and iron.
文摘The influence of γ-phase composition in WC-Co cemented carbides on its specific coercive force H_(sc) hasbeen studied by analysing the imitative alloys of γ-phase. The results show that the H_(sc) of γ-phase is lower thanthat of pure cobalt, because the solute W can raise γ-phase H_(sc) but the carbon exhibits more intense negativeeffect on H_(sc). The effect is enhanced with raising the C solubilities in γ-phase.
文摘The allotropic transformation process of the γ-phase in WC-Co cemented carbides has been explored.Theconcepts of γ-grain and the γ-domain have been proposed forward:The γ-domain is the residual FCC-typeβ-Co grain that failed to transform when cooling alloy sample and γ-base is the HCP-type x-Co transformedmainly by means of diffusion,the outline of the γ-grain is consistent with the newly fromed β-Co grain formedat high temperature.The quantity and distribution of γ-grain domain are related to the cooling rate after sinter-ing and influence the alloys properties.
基金Funded by the National Natural Science Foundation of China(No.51465009)Natural Science Foundation of Guizhou Province(Guizhou Science and Technology Agency)(No.J[2014]2085)+1 种基金Academician Workstation of Guizhou Institute of Technology(No.(2014)4007)Department of Education of Guizhou Province 125 Project(No.[2014]035)。
文摘In order to optimize the tool coating material and reduce the tool wear rate,the coating material and wear mechanism for carbide tools are proposed and analyzed based on thermodynamics theory.We deduced the Gibbs free energy function method and analyzed the enthalpy value of the coating material of cemented carbide tools.The rules of diffusion wear and oxidation wear for WC-Co-based carbide tools were analyzed based on the diffusion dissolution theory and the calculation method of the thermal effect of chemical reaction.The diffusion wear and oxidation wear of WC-Co-based carbide tools when machining Ti-6Al-4V were studied with SEM-EDS.The results indicate that a good prediction accuracy of both diffusion wear and oxidation wear can be achieved by the method of thermodynamic theory analysis method.The conclusion will provide useful references for the optimization of cutting parameters and the improvement of the tool life.
基金Project(12JJ8018)supported by the Natural Science Foundation of Hunan Province,China
文摘The effects of deep cryogenic treatment on the microstructure and properties of WC-11 Co cemented carbides with various carbon contents were investigated.The results show that after deep cryogenic treatment,WC grains are refined into triangular prism with sound edges via the process of spheroidization,but WC grain size has no evident change compared with that of untreated alloys.The phase transformation of Co phase from α-Co(FCC) to ε-Co(HCP) is observed in the cryogenically treated alloys,which is attributed to the decrease of W solubility in the binder(Co).Deep cryogenic treatment enhances the hardness and bending strength of the alloys,while it has no significant effects on the density and cobalt magnetic performance.
文摘The morphologies and formation process of Ni-pool defects in WC?8Ni cemented carbides were studied. The SEM images show that Ni-pool generally has two kinds of morphologies: “island” in isolation and “ring” around a new phase. In the obtained samples with “ring-like Ni-pool”, WC, Ni and Ni2W4C (η phase) phases were detected in XRD patterns. Combined with SEM, EDX and XRD results, it is found that the phase in the center of the “ring-like Ni-pool” is Ni2W4C (η phase) and the main chemical components of Ni-pool are Ni, W and C. In addition, the relationships among large size Ni (agglomerated) particles, volatile impurities, pores and carbon content vs forming process of the Ni-pool defects for WC?8Ni cemented carbides are also presented and discussed.
文摘A new cup-type grinding wheel of the brazed monolayer diamond is developed with a defined grain pattern on the wheel surface. Grinding performance of the brazed wheel in the surface grinding of cemented carbide is studied. Experimental results show that when continuous dry grinding is employed, grits of the brazed diamond grinding wheel fail mainly in attritious wear and fracture modes and no pull-out ones are found in conventional electroplated and sintered diamond wheels. It indicates the strong retention of brazing alloy to diamond grits and the longer service life of the wheel. In addition, the ground surface has good roughness. The theoretical surface roughness agrees well with experimental results.
基金This work was supported by open foundation of State Key Laboratory of Advanced Technology for Materials Synthesis&Processing,Wuhan University of Technology under grant No.200301126the Postdoctoral Science Foundation of China under grant No.2003034504the Chinese 863 programme under grant No.2002A A302504.
文摘Nanocrystalline tungsten carbide-cobalt (WC-Co) composite powders produced through spray thermal decomposition-continuous reduction and carburization technology were used to prepare φ3.25 mm×38 mm ultrafine tungsten carbide-cobalt (WC-Co) cemented carbide rods through vacuum sintering plus sinterhip technology. The microstructure, Vickers hardness, density and Rockwell A hardness (HRA), transverse rupture strength (TRS), saturated magnetization and coercivity force were tested. The results show that the average grain size of the sintering body prepared through vacuum sintering plus sinterhip technology was 430 nm; transverse rupture strength (TRS) was 3850 MPa; Vickers hardness was 1890 and Rockwell A hardness of sintering body was 93. High strength and high hardness ultrafine WC-Co cemented carbide rods used to manufacture printed circuit board (PCB) drills were obtained.
基金Project(2013zzts025)supported by the Fundamental Research Funds for the Central Universities of China
文摘Coarse grained WC-9Co cemented carbides with 0-1.0% TaC(mass fraction) were fabricated by HIP-sintering and gas quenching. The effects of TaC on the microstructures and mechanical properties were investigated using scanning electron microscopy(SEM), energy dispersive X-ray analysis(EDS), X-ray diffractometry(XRD) and mechanical properties tests. The results show that the maximum values of hardness and strength are HV 1124 and 2466 MPa respectively when 0.4% TaC is added. When the content of TaC is more than 0.6%, the grain size of WC is no longer affected by the amount of TaC, and(W,Ta)C occurs as well. Moreover, the strength and fracture toughness increase and the(Ta+W) content decreases with the increase of TaC content. The dependence of(Ta+W) content on the mechanical properties indicates that(Ta+W) content in Co should be decreased as low as possible to improve the mechanical properties of coarse grained WC-TaC-9Co cemented carbides with the microstructure of WC+γ two phase regions.
文摘Aim To research on a solid cemented carbide multi facet drill for drilling high strength steel. Methods Assimilating some features of multi facet drill edge structures, through systematic drilling experiments, a new type of solid cemented carbide drill was developed and the drill geometry was optimized. Results With the new type drill,the drilling force decreases by 10%-20%, the drilling productivity (drilled holes per hour) increases by 2-3 times, and the drilling precision and surface finish increase by one level. Conclusion The new type drill possesses excellent drilling performance.
基金The National Natural Science Foundation of China(No.50323008,31070517)Scientific Research Foundation of Guangxi Education Department(No.201203YB097)
文摘Finite dement formulations are used to simulate the evolution of the elastoplastic response of functionally graded cemented carbides (FGCC) due to thermal loading. The geometry of specimens is an axisymmetric solid cylinder with a two-dimensional gradient. The elastoplastic constitutive relationship is developed by constraint factors. Numerical results show that compressive stresses occur in the surface zone and tensile stresses in the cobalt rich zone when the temperature drops from the initial stress-free temperature of 800 to 0℃. The maximum value of the surface compressive stress is 254 MPa and the maximum value of the tensile stress is 252 MPa in the cobalt rich zones. When the cobalt concentration difference in the specimens is equal to or greater than 0.3, there is pronounced plastic flow in cobalt rich zone. When the temperature heats up from 0 to 800 ℃, the total plastic strain reaches 0.001 4. Plastic flow has a significant effect on the reduction of thermal stress concentration.