Microstructure Characteristics of Ni-Nb Near Eutectic Alloy during EBFZM Directional Solidification

Microstructure Characteristic of Ni-Nb near eutectic alloy is systematically investigated during directional solidification with electron beam floating zone melting (EBFZM). The effect of the Zone melting rate on the microstructure has also been studied.

Temperature-Dependent Photoluminescence Characteristics of InAs/GaAs Quantum Dots Directly Grown on Si Substrates

The first operation of an electrically pumped 1.3μm InAs/GaAs quantum-dot laser was previously reported epitaxially grown on Si （100） substrate. Here the direct epitaxial growth condition of 1.3μm InAs/OaAs quantum on a Si substrate is further investigated using atomic force microscopy, etch pit density and temperature-dependent photoluminescence （PL） measurements. The PL for Si-based InAs/GaAs quantum dots appears to be very sensitive to the initial OaAs nucleation temperature and thickness with strongest room-temperature emission at 40000 （17Onto nucleation layer thickness）, due to the lower density of defects generated under this growth condition, and stronger carrier confinement within the quantum dots.

The surface wave suppression using the second generation curvelet transform

In this paper,we develop a new and effective multiple scale and strongly directional method for identifying and suppressing ground roll based on the second generation curvelet transform.Making the best use of the curvelet transform＇s strong local directional characteristics,seismic frequency bands are transformed into scale data with and without noise.Since surface waves and primary reflected waves have less overlap in the curvelet domain,we can effectively identify and separate noise.Applying this method to prestack seismic data can successfully remove surface waves and,at the same time,protect the reflected events well,particularly in the low-frequency band.This indicates that the method described in this paper is an effective and amplitude-preserving method.

Gradient principle of horizontal stress inducing rock burst in coal mine

Based on the stress distribution characteristics of rock burst multiple sites, the criterion of horizontal stress inducing layer dislocation rock burst was established. Accordingly, the influencing factors were analyzed. The analysis results indicate that the stress condition, edge of etastic zone depth, supporting strength, and the friction angle and cohesion among coal stratum, roof and floor are sensitive factors. By introducing double-couple model, the layer dislocation rock burst was explained and the energy radiation characteristics were analyzed. The SOS micro-seismic monitoring system was applied to observe the rock burst hazards about a mining face. The results show that P- and S-wave energy radiations produced by rock burst have directional characteristics. The energy radiation characteristics of the 22 rock bursts occurring on 79Z6 long-wall face are basically the same as theoretical results, that is, the ratio of S-wave energy of sensor 4 to 6 is about 1.5 and that of P-wave is smaller than 0.5. The consistency of the monitored characteristics of the energy radiation theoretically increases with the total energy increasing.

Microstructural characteristics and deformation of magnesium alloy AZ31 produced by continuous variable cross-section direct extrusion

Magnesium（Mg） alloy AZ31 was produced by continuous variable cross-section direct extrusion（CVCDE）to study its deformation behavior. Metallographic microscopy（OM）, transmission electron microscopy（TEM）, and scanning electron microscopy（SEM） were used to observe the variations in microstructure and fracture morphology of Mg alloy AZ31 as a function of processing methods. The results reveal that grains of Mg alloy AZ31 were refined and their microstructure was homogenized by CVCDE. The recrystallization in Mg alloy AZ31 produced by CVCDE with 2 interim dies was more complete than that produced by conventional extrusion（CE） and CVCDE with 1 interim die, and the grains were finer and more uniform.Plasticity of the AZ31 alloy was improved. Fracture mode was evolved from a combination of ductility and brittleness to a sole ductile form. In summary, a CVCDE mold structure with 2 interim dies can improve microstructure, plasticity, and toughness of Mg alloy AZ31.

A NOTE ON THE STABILITY OF A CLASS OF DEGENERATE PLANAR CRITICAL POINTS

A computable expression of the asymptotic expansion of the return map for a degenerate singular point of a class of planar differential system is given, and hence the stability and the type of the singular point can be decided. These results generalize the corresponding results in [Nonlinearity, 13 （2000）, p.709].

Hydrodynamics characterization of a choanoid fluidized bed bioreactor used in the bioartificial liver system： Fully resolved simulation with a fctitious domain method

Choanoid fluidized bed bioreactors （CFBBs） are newly developed core devices used in bioartificial liver- support systems to detoxify blood plasma of patients with microencapsulated liver cells. Direct numerical simulations （DNS） with a direct-forcing/fictitious domain （DF/FD） method were conducted to study the hydrodynamic performance of a CFBB. The effects of particle-fluid density ratio, particle number, and fil- ter screens preventing particles flowing out of the reactor were investigated. Depending on density ratio, two flow patterns are evident： the circulation mode in which the suspension rises along one sidewall and descends along the other sidewall, and the non-circulation mode in which the whole suspension roughly flows upward. The circulation mode takes place under non-neutral-buoyancy where the particle sedimentation dominates, whereas the non-circulation mode occurs under pure or near-neutral buoy- ancy with particle-fluid density ratios of unity or near unity. With particle-fluid density ratio of 1.01, the bioartificial liver reactor performs optimally as the significant particle accumulation existing in the non-circulation mode and the large shear forces on particles in the circulation mode are avoided. At higher particle volume fractions, more particles accumulate at the filter screens and a secondary counter circulation to the primary flow is observed at the top of the bed. Modelled as porous media, the filter screens play a negative role on particle fluidization velocities; without screens, particles are fluidized faster because of the higher fluid velocities in the jet center region. This work extends the DF/FD-based DNS to a fluidized bed and accounts for effects from inclined side walls and porous media, providing some hydrodynamics insight that is important for CFBB design and operation optimization.