Numerical Simulation on Subcooled Boiling Heat Transfer Characteristics of Water-Cooled W/Cu Divertors

In order to realize safe and stable operation of a water-cooled W/Cu divertor under high heating condition,the exact knowledge of its subcooled boiling heat transfer characteristics under different design parameters is crucial.In this paper,subcooled boiling heat transfer in a water-cooled W/Cu divertor was numerically investigated based on computational fluid dynamic（CFD）.The boiling heat transfer was simulated based on the Euler homogeneous phase model,and local differences of liquid physical properties were considered under one-sided high heating conditions.The calculated wall temperature was in good agreement with experimental results,with the maximum error of 5%only.On this basis,the void fraction distribution,flow field and heat transfer coefficient（HTC）distribution were obtained.The effects of heat flux,inlet velocity and inlet temperature on temperature distribution and pressure drop of a water-cooled W/Cu divertor were also investigated.These results provide a valuable reference for the thermal-hydraulic design of a water-cooled W/Cu divertor.

Luminescence Characteristics and Energy Transfer Machanismof LaOBr:Tb^(3+) (Dy^(3+))

The rare earth luminescence materials LaOBrfTb3+(Dy3+) were synthesized at high temperature,and the structure and luminescence characteristics were studied. The co-doping Dy3+ may make the energy of 5D3 of Tb3+ transfer to 5D4 level, which makes the emission of 5D4-7FJ (J=0,1... 6), specially of 5D4-7F5, enhance obviously, and the total brightness is increased by about 40% in comparison with the samples without Dy3+ cations, as a result of the energy transfer of dipole-dipole interaction.

Experimental investigation of bioheat transfer characteristics induced by pulsed-laser irradiation

An experimental study of bioheat transfer characteristics induced bypulsed-laser irradiation was presented. The heat transfer characteristics of bio-materials, and theinfluences of pulse duration, power density, species of bio-materials, thickness and initialmoisture content of bio-materials on heat transfer were studied in details. The experimental resultsindicate that the penetration and absorption of laser in bio-materials are considerable, the heattransfer inside the bio-materials should include the effects of volumetric absorption, pulseduration, power density, bio-materials thickness, and material species have a significant influenceon the temperature variation.

Heat Transfer Characteristics and Pressure Drop in a Horizontal Circulating Fluidized Bed Evaporator

A vapor-liquid-solid horizontal circulating fluidized bed evaporation setup was constructed to study the thermal-exchange properties and pressure change.The influences of the operating variables,including the amount of added particles,heat flux,and circulating flow velocity,were systematically inspected using resistance temperature detectors and pressure sensors.The results showed that the heat transfer eff ect was improved with the increase in the amount of added particles,circulating flow velocity,and particle diameter,but decreased with increasing heat flux.The pressure drop fluctuated with the increase in operating parameters,except circulating flow velocity.The enhancing factor reached up to 71.5%.The enhancing fac-tor initially increased and then decreased with the increase in the amount of added particles and circulating flow velocity,fluctuated with increasing particle diameter,and decreased with increasing heat flux.Phase diagrams showing the variation ranges of the operation variables for the enhancing factor were constructed.

A simulating investigation into the characteristics of the mass transfer between molten steel and particles in the 150 t RH-IJ refining

The characteristics of the mass transfer between powder particles and liquid steel in the Ruhrstahl Heraeus process injection （RH-IJ） refining were simulatively investigated by the use of a 1/4 scale water model of a 150 t Ruhrstahl Heraeus（RH） degasser. The influences of the lifting gas flow rate, the up-snorkel and down-snorkel inner diameters and the size of powder particles on the characteristics of the mass transfer were examined. The results show that under the condition that the inner diameters of both the up-snorkel and the down-snorkel are the same, the mass transfer coefficient in the liquid,k increases with the increase of the inner diameter of the up-snorkel,the particle size and the lifting gas flow rate （Q1）. However, the increase of Q~ should not result in a saturated circulation rate. Under the current working condition,k ranges from 3. 392 × 10 -5 m/s to 2. 661 × 10-4 m/s. On the other hand,with a given lifting gas flow rate and up-snorkel inner diameters ,the mass transfer weakens with the increase of the down-snorkel inner diameter. An inherently nonlinear relationship between the circulation rate （Q~） of molten steel in the RH degasser and k,which increases with the increase of Q1,was found. Under the condition of other parameters being the same,k increases with the increase of the powder particle size. In order to enhance the mass transfer,it is better not to use extremely fine powder.

Research on the Flow and Heat Transfer Characteristics of a Water-Cooling Plate in a Heat Dissipation System

The water-cooling heat dissipation technology can solve the heat dissipation and noise problems of the calculation plate.Therefore,the structural design of the water-cooling plate directly affects its flow and heat transfer characteristics,which restricts the promotion and application of the technology.To this end,the water-cooling plate of a heat dissipation system was taken as the research object,and its flow and heat transfer characteristics were numerical simulated and experimental studied.Through comparative analysis,the rationality of the numerical simulation method was verified.Based on this,three improved schemes of water-cooling plate structure were proposed and numerical simulation was carried out,and the optimal model was verified by experiments.The results of the study show that compared with the original water-cooling plate,the optimized water-cooling plate has increased internal flow velocity and distributes uniformly,increased heat transfer amount by 4.2%,and the average temperature of the calculation plate decreased by 5.3%.

Observation of a Current Plateau in the Transfer Characteristics of InGaN/AlGaN/AlN/GaN Heterojunction Field Effect Transistors

Direct-current transfer characteristics of （InGaN）/A1GaN/A1N/GaN heterojunction field effect transistors （HFETs） are presented. A drain current plateau （IDs = 32.0 mA/mm） for Vcs swept from ＋0.7 V to -0. 6 V is present in the transfer characteristics of InGaN/AIGaN/AIN/GaN HFETs. The theoretical calculation shows the coexistence of two-dimensional electron gas （2DEG） and two-dimensional hole gas （2DHG） in InGaN/AIGaN/A1N/GaN heterostructures, and the screening effect of 2DHG to the 2DEG in the conduction channel can explain this current plateau. Moreover, the current plateau shows the time-dependent behavior when IDs Vcs scans repeated are conducted. The obtained insight provides indication for the design in the fabrication of GaN-based super HFETs.

Major Characteristics for the Transfer of Rural Surplus Labourers

ＭａｊｏｒＣｈａｒａｃｔｅｒｉｓｔｉｃｓｆｏｒｔｈｅＴｒａｎｓｆｅｒｏｆＲｕｒａｌＳｕｒｐｌｕｓＬａｂｏｕｒｅｒｓ￥／／Ａｎａｔｉｏｎａｌｓａｍｐｌｉｎｇｓｕｒｖｅｙｏｎ１２４，０００ｌａｂｏｕｒｅｒｓｆｒｏｍ６４，０００ｒｕｒａｌｈｏｕｓｅｈｏｌｄ...

Research on Flow and Heat Transfer Characteristics Inside Spiral Pile-honeycomb Structures with Different Shapes

Spiral plate heat exchanger is a traditional compact heat exchanger,and widely used in the occasion of the high heat transfer capacity requirements,such as waste heat recovery. In the situation of energy shortage and rapid development of heat transfer technology^([1-3]),cylindrical,elliptical and rhombic spiral pile-honeycomb heat transfer models are established^([4-5]). The internal flow and heat transfer are simulated by using CFD software FLUENT15. 0 and RNG k-ε turbulent model,and then the three models are analyzed. The results show that the secondary flow and vortex are induced again in the secondary honeycomb,which further increases the turbulence intensity of the fluid. The thickness of the boundary layer is reduced twice,and the heat transfer effect is better than that of the honeycomb spiral structure. The spiral pile-honeycomb model for the rhombus is better than the models of cylinder and ellipse in heat transfer performance.

Flow Boiling Heat Transfer Characteristics and Delayed Dry-Out Ability of Non-Azeotropic Mixtures R245fa/R134a in Microchannels

Microchannel flow boiling heat transfer has the advantages of strong heat dissipation capacity,good temperature uniformity,and compact structure.It is an excellent way to thermally manage electronic devices,but when the heat flux exceeds CHF(Critical Heat Flux),the heat transfer performance deteriorates as the working fluid dries out.Non-azeotropic mixtures have the potential to effectively delay or avoid dry-out during the boiling process due to their temperature slide characteristics which causes the mass transfer resistance.To understand the influence of non-azeotropic mixtures on microchannel flow boiling,using the phase-change microchannel heat sink as the research object,the experiments on the flow boiling heat transfer performance of R245fa/R134a mixtures under different working conditions were carried out,and the characteristics of flow boiling heat transfer were obtained under the different working conditions,and comparison was developed with those of pure substance R245fa.The results demonstrated that a small amount of low-boiling-point components in the high-boiling-point working fluid inhibited boiling heat transfer to some extent,and lowered the average heat transfer coefficient under the non-dryout condition slightly lower than that of the pure substance;however,it also effectively delayed the onset of local dry-out and prevented significant deterioration in thermal transfer performance under the lower mass flow rate and higher heat flux,which could enhance the heat sink's stability.

Comparative Experimental Study on Heat Transfer Characteristics of Building Exterior Surface at High and Low Altitudes

The external surface heat transfer coefficient of building envelope is one of the important parameters necessary for building energy saving design,but the basic data in high-altitude area are scarce.Therefore,the authors propose a modified measurement method based on the heat balance of a model building,and use the same model building to measure its external surface heat transfer coefficient under outdoor conditions in Chengdu city,China at an altitude of 520 m and Daocheng city at an altitude of 3750 m respectively.The results show that the total heat transfer coefficient(h_(t))of building surface in high-altitude area is reduced by 34.48%.The influence of outdoor wind speed on the convective heat transfer coefficient(h_(c))in high-altitude area is not as significant as that in low-altitude area.The fitting relation between convection heat transfer coefficient and outdoor wind speed is also obtained.Under the same heating power,the average temperature rise of indoor and outdoor air at highaltitude is 41.9%higher than that at low altitude,and the average temperature rise of inner wall is 25.8%higher than that at low altitude.It shows that high-altitude area can create a more comfortable indoor thermal environment than low-altitude area under the same energy consumption condition.It is not appropriate to use the heat transfer characteristics of the exterior surface of buildings in low-altitude area for building energy saving design and related heating equipment selection and system terminal matching design in high-altitude area.

CFD Analysis of Fluid-Dynamic and Heat Transfer Effects Generated by a Fixed Electricity Transmission Line Interacting with an External Wind

The flow past a fixed single transmission conductor and the related heat transfer characteristics are investigated using computational fluid dynamics and a relevant turbulence model.After validating the method through comparison with relevant results in the literature,this thermofluid-dynamic problem is addressed considering different working conditions.It is shown that the resistance coefficient depends on the Reynolds number.As expected,the Nusselt number is also affected by Reynolds number.In particular,the Nusselt number under constant heat flux is always greater than that under a constant wall temperature.

DYNAMIC CHARACTERISTICS ON PRECISION NC LATHE BASED ON MULTI-BODY SYSTEM THEORY

Based on multi-body system theory and the mainshafl system of precision NC lathe as object investigated, it is treated as a coupled rigid-flexible multi-body system which is made up of some rigid and elastic bodies in an especial linking mode. And a dynamic model is established, The problems of computing vibration characteristics are resolved by using multi-body system transfer matrix method, Resutts show that the mainshaft system of NC lathe is in the stable and reliable working area all the time. The method is simple and easy, the idea is clear. In addition, the method can be easily used and popularized in the other multi-body system.

Graphene Bridge Heterostructure Devices for Negative Differential Transconductance Circuit Applications

Two-dimensional van der Waals(2D vdW)material-based heterostructure devices have been widely studied for high-end electronic applications owing to their heterojunction properties.In this study,we demonstrate graphene(Gr)-bridge heterostructure devices consisting of laterally series-connected ambipolar semiconductor/Gr-bridge/n-type molybdenum disulfide as a channel material for field-effect transistors(FET).Unlike conventional FET operation,our Gr-bridge devices exhibit nonclassical transfer characteristics(humped transfer curve),thus possessing a negative differential transconductance.These phenomena are interpreted as the operating behavior in two series-connected FETs,and they result from the gate-tunable contact capacity of the Gr-bridge layer.Multi-value logic inverters and frequency tripler circuits are successfully demonstrated using ambipolar semiconductors with narrow-and wide-bandgap materials as more advanced circuit applications based on non-classical transfer characteristics.Thus,we believe that our innovative and straightforward device structure engineering will be a promising technique for future multi-functional circuit applications of 2D nanoelectronics.

Experimental Investigation of the Operating Characteristics of a Pulsating Heat Pipe with Ultra-Pure Water and Micro Encapsulated Phase Change Material Suspension

The specific heat capacity of working fluid is an important influence factor on heat transfer characteristic of the pulsating heat pipe(PHP).Due to the relatively large specific heat capacity of micro encapsulated phase change material(MEPCM) suspension,a heat transfer performance experimental facility of the PHP was established.The heat transfer characteristic with MEPCM suspension of different mass concentrations(0.5% and 1.0%) and ultra-pure water were compared experimentally.It was found that when the PHP uses MEPCM suspension as its working fluid,operating stability is impoverished under lower heating power and the operating stability is better under higher heating power.At the inclination angle of 90°,the temperature at heating side decreases compared to ultra-pure water and the temperature at heating side decreases with the raising of MEPCM suspension mass concentration.The heat transfer characteristic of the PHP is positively correlated with the inclination angle and the 90° is optimum.The unfavorable effect of the inclination angle decreases with heating power increasing.When the inclination angle is 90°,the PHP with MEPCM suspension at 1.0% of mass concentration has the lowest thermal transfer resistance and followed by ultra-pure water and MEPCM suspension at 0.5% of mass concentration has the highest thermal transfer resistance.When the inclination angles are 60° and30°,the effect of gravity on the flow direction is reduced to 86.6% and 50% of that on the inclination angle of 90°,respectively,and the promoting effect of gravity on the working fluid is further weakened as the inclination angle further decreases.Due to the high viscosity of MEPCM suspension,the PHP with ultra-pure water has the lowest heat transfer resistance.When the inclination angles is 60°,the thermal resistance with MEPCM suspension at0.5% of the mass concentration is lower than that at 1.0% at the heating power below 230 W.The thermal resistance of MEPCM suspension tends to be similar for heating power of 230-250 W.At the heating power above 270 W,the thermal resistance with MEPCM suspension at 1.0% of the mass concentration is lower than that at 0.5%.

Physical Modeling of the Vacuum Circulation Refining Process of Molten Steel

The available studies in the literature on physical modeling of the vacuum circulation (RH, i.e. Ruhrstahl Heraeus) refining process of molten steel have briefly been reviewed. The latest advances made by the author with his research group have been summarized. Water modeling was employed to investigate the flow and mixing characteristics of molten steel under the RH and RH KTB (Kawasaki top blowing) conditions and the mass transfer features between molten steel and powder particles in the RH PTB (powder top blowing) refining. The geometric similarity ratio between the model and its prototype (a multifunction RH degasser of 90 t capacity) was 1:5. The effects of the related technological and structural factors were considered. These latest studies have revealed the flow and mixing characteristics of molten steel and the mass transfer features between molten steel and powder particles in these processes, and have provided a better understanding of the refining processes of molten steel.

Heat transfer characteristics in a narrow confined channel with discrete impingement cooling

Heat transfer characteristics in a narrow confined channel with discrete impingement cooling were investigated using thermal infrared camera. Detailed heat transfer distributions and comparisons on three surfaces with three impact diameters were experimentally studied in the range of Reynolds number of 3000 to 30000. The experimental results indicated that the strong impingement jet leaded to a high strength heat transfer zone in the ΔX=±2.5D;range of the impact center,which was 1.3–2.5 times of the average heat transfer value of the impingement wall. With the same coolant mass flow rate, small diameter case had lower heat transfer coefficient on both inner wall and outside wall, while the impingement wall was insensitive to the impact diameter. The surface averaged Nusselt number of inner wall was only 43%–57% of impingement wall, while the outside wall can reach up to 80%–90%. The larger the diameter, the higher heat transfer enhancement and the smaller the channel flow resistance was observed in term of Reynolds number. The surface averaged Nusselt numbers were developed as the function of Reynolds number and the impingement height-to-diameter for further engineering applications.

Design and Analysis of a Novel Compliant Mechanism with RPR Degrees of Freedom

A novel compliant mechanism with RPR degrees of freedom(DOF)is proposed where R and P represent rotation and translation DOFs,respectively.The proposed compliant mechanism is obtained from dimension synthesizing a 2-RPU-UPR rigid parallel mechanism with the method of optimization of motion/force transfer characteristic.R,P and U represent rotation,translation and universal pairs,respectively.Firstly,inverse kinematics and Jacobian matrix are analyzed for the dimensional synthesis.Then,output transmission indexes of branches in the parallel mechanism are given.Dimensional synthesis is completed based on the normalized design parameter.And optimization of flexure joints based on constrained energy is carried out.Afterwards,the novel compliant mechanism is obtained by direct replacing method.Mechanical model of the compliant mechanism including static stiffness and input stiffness is built based on the pseudo-rigid body modeling method and virtual work principle.Finally,FEA simulation by Ansys Workbench is carried out to verify DOF,effectiveness of the dimension synthesis,and compliant model.Optimization of motion/force transfer characteristic is first applied for the design of compliant mechanisms to suppress drift of rotation axis in the paper.

Electromagnetohydrodynamic flows and mass transport in curved rectangular microchannels

Curved microchannels are often encountered in lab-on-chip systems because the effective axial channel lengths of such channels are often larger than those of straight microchannels for a given per unit chip length.In this paper,the effective diffusivity of a neutral solute in an oscillating electromagnetohydrodynamic(EMHD)flow through a curved rectangular microchannel is investigated theoretically.The flow is assumed as a creeping flow due to the extremely low Reynolds number in such microflow systems.Through the theoretical analysis,we find that the effective diffusivity primarily depends on five dimensionless parameters,i.e.,the curvature ratio of the curved channel,the Schmidt number,the tidal displacement,the angular Reynolds number,and the dimensionless electric field strength parameter.Based on the obtained results,we can precisely control the mass transfer characteristics of the EMHD flow in a curved rectangular microchannel by appropriately altering the corresponding parameter values.

On the low frequency characteristics of head-related transfer function

A method to correct the measured head-related transfer functions （HRTFs） at low frequency was proposed. By analyzing the HRTFs from the spherical head model at low frequency, it is proved that below the frequency of 400 Hz, magnitude of HRTF is nearly constant and the phase is a linear function of frequency both for the far and near field. Therefore, if the HRTFs above 400 Hz are accurately measured by experiment, it is able to correct the HRTFs at low frequency by the theoretical model. The results of calculation and subjective experiment show that the feasibility of the proposed method.