Hydrogen-bonded organic framework modified separator for simultaneously enhancing the safety and electrochemical performance of Ni-rich lithium-ion battery

Nickel-rich layered oxide cathode(LiNi_(x)Co_(y)Mn_(1−x−y)O_(2),x>0.5,NCM)shows substantial potential for applications in longer-range electrical vehicles.However,the rapid capacity decay and serious safety concerns impede its practical viability.This work provides a hydrogen-bonded organic framework(HOF)modification strategy to simultaneously improve the electrochemical performance,thermal stability and incombustibility of separator.Melamine cyanurate(MCA),as a low-cost and reliable flame-retardant HOF,was implemented in the separator modification layer,which can prevent the battery short circuit even at a high temperature.In addition,the supermolecule properties of MCA provide unique physical and chemical microenvironment for regulating ion-transport behavior in electrolyte.The MCA coating layer enabled the nickel-rich layered oxide cathode with a high-capacity retention of 90.3%after 300 cycles at 1.0 C.Collectively,the usage of MCA in lithium-ion batteries(LIBs)affords a simple,low-cost and efficient strategy to improve the security and service life of nickel-rich layered cathodes.

Bound-Preserving Discontinuous Galerkin Methods with Modified Patankar Time Integrations for Chemical Reacting Flows

In this paper,we develop bound-preserving discontinuous Galerkin(DG)methods for chemical reactive flows.There are several difficulties in constructing suitable numerical schemes.First of all,the density and internal energy are positive,and the mass fraction of each species is between 0 and 1.Second,due to the rapid reaction rate,the system may contain stiff sources,and the strong-stability-preserving explicit Runge-Kutta method may result in limited time-step sizes.To obtain physically relevant numerical approximations,we apply the bound-preserving technique to the DG methods.Though traditional positivity-preserving techniques can successfully yield positive density,internal energy,and mass fractions,they may not enforce the upper bound 1 of the mass fractions.To solve this problem,we need to(i)make sure the numerical fluxes in the equations of the mass fractions are consistent with that in the equation of the density;(ii)choose conservative time integrations,such that the summation of the mass fractions is preserved.With the above two conditions,the positive mass fractions have summation 1,and then,they are all between 0 and 1.For time discretization,we apply the modified Runge-Kutta/multi-step Patankar methods,which are explicit for the flux while implicit for the source.Such methods can handle stiff sources with relatively large time steps,preserve the positivity of the target variables,and keep the summation of the mass fractions to be 1.Finally,it is not straightforward to combine the bound-preserving DG methods and the Patankar time integrations.The positivity-preserving technique for DG methods requires positive numerical approximations at the cell interfaces,while Patankar methods can keep the positivity of the pre-selected point values of the target variables.To match the degree of freedom,we use polynomials on rectangular meshes for problems in two space dimensions.To evolve in time,we first read the polynomials at the Gaussian points.Then,suitable slope limiters can be applied to enforce the positivity of the solutions at those points,which can be preserved by the Patankar methods,leading to positive updated numerical cell averages.In addition,we use another slope limiter to get positive solutions used for the bound-preserving technique for the flux.Numerical examples are given to demonstrate the good performance of the proposed schemes.

Electrochemical Degradation of Indigocarmine Dye at Ni/Graphite Modified Electrode in Aqueous Solution

Nickel Graphite modified electrode (Ni/GME) was prepared by electrochemical method and degradation of Indigocarmine (IC) dye was carried out. An investigation between the efficiency of degradation by graphite electrode and the Ni/graphite modified electrode has been carried out. The different effects of concentration, current density and temperature on the rate of degradation were studied. This study shows that the rate of the degradation is more for Ni doped modified graphite electrode. UV-Visible spectra before and after degradation of the dye solution were observed. The thin film formation of Ni or encapsulated in graphite rod is observed by scanning electron microscopy and energy dispersive X-ray spectroscopy (SEM & EDAX). The instantaneous current effectiveness values of different experimental conditions are evaluated. The anodic oxidation by Ni/ graphite modified electrode showed the complete degradation of aqueous solution indigocarmine, which is confirmed by UV-Visible and chemical oxygen demand (COD) measurements. The dye is converted into CO2, H2O and simpler inorganic salts. The results observed for reuse of modified electrodes indicate that the Ni/graphite modified electrode would be a promising anode for electrochemical degradation of indigocarmine. This method can be applied for the remediation of waste water containing organics, cost-effective and simple.

利用同化资料改进WRF-Chem对华北地区秋季PM_(2.5)预报的研究

气溶胶初始场同化能够提高WRF-Chem气象-气溶胶耦合预报的准确度。为了讨论气溶胶同化在不同时刻对耦合模式预报的影响,针对2015年10月一次重度霾污染过程,进行了一天4个不同时刻的气象-气溶胶联合同化及短时预报试验研究。结果表明,在同化气象资料的基础上同化气溶胶观测资料能够改善不确定性较大的排放源清单带来的模拟高估问题,减小初始场PM_(2.5)的正偏差;随着初始场PM_(2.5)浓度的下降,气溶胶导致的地面辐射的下降减弱,使得日间时刻6 h预报场的向下短波辐射量增加;日间近地面温度和湿度对辐射量变化的响应(增温减湿)呈现为在空间大面积上的重合和时间上的同步,这种响应在循环滚动预报的影响下即使在夜间也得到了延续;近地面增温减湿的结构有助于边界层向上发展,从而促进气溶胶的向上传输,最终进一步减弱预报场对地表PM_(2.5)的高估。因此,气溶胶同化带来的初始场PM_(2.5)信息的改善,使得6 h耦合预报的结果更加准确。

Modelling of the elastoplastic behaviour of the bio-cemented soils using an extended Modified Cam Clay model

An elastoplastic constitutive model based on the Modified Cam Clay(MCC)model is developed to describe the mechanical behaviour of soils cemented via microbially induced calcite precipitation(MICP).It considers the increase of the elastic stiffness,the change of the yield surface due to MICP cementation and the degradation of calcium carbonate bonds during shearing.Specifically,to capture the typical contraction-dilation transition in MICP soils,the original volumetric hardening rule in the MCC model is modified to a combined deviatoric and volumetric hardening rule.The model could reproduce a series of drained triaxial tests on MICP-treated soils with different calcium carbonate contents.Further,we carry out a parametric study and observe numerical instability in some cases.In combination with an analytical analysis,our numerical modelling has identified the benefits and limitations of using MCCbased models in the simulation of MICP-cemented soils,leading to suggestions for further model development.

A dual-RPA based lateral flow strip for sensitive,on-site detection of CP4-EPSPS and Cry1Ab/Ac genes in genetically modified crops

Traditional transgenic detection methods require high test conditions and struggle to be both sensitive and efficient.In this study,a one-tube dual recombinase polymerase amplification(RPA)reaction system for CP4-EPSPS and Cry1Ab/Ac was proposed and combined with a lateral flow immunochromatographic assay,named“Dual-RPA-LFD”,to visualize the dual detection of genetically modified(GM)crops.In which,the herbicide tolerance gene CP4-EPSPS and the insect resistance gene Cry1Ab/Ac were selected as targets taking into account the current status of the most widespread application of insect resistance and herbicide tolerance traits and their stacked traits.Gradient diluted plasmids,transgenic standards,and actual samples were used as templates to conduct sensitivity,specificity,and practicality assays,respectively.The constructed method achieved the visual detection of plasmid at levels as low as 100 copies,demonstrating its high sensitivity.In addition,good applicability to transgenic samples was observed,with no cross-interference between two test lines and no influence from other genes.In conclusion,this strategy achieved the expected purpose of simultaneous detection of the two popular targets in GM crops within 20 min at 37°C in a rapid,equipmentfree field manner,providing a new alternative for rapid screening for transgenic assays in the field.

Rechargeable Na-MnO_(2) battery with modified cell chemistry

High voltage,high energy density,nominal cycle life,and low cost are the most critical requirements of rechargeable batteries for their widespread energy storage applications in electric vehicles and renewable energy technologies.Na-MnO_(2) battery could be a low-cost contender,but it suffers extensively from its low cell voltage and poor rechargeability.In this study,we modified the conventional cell structure of Na-MnO_(2) battery and established altered cell chemistry through a hybrid electrochemical process consisting of Na striping/plating at the anode and Zn^(2+) insertion/de-insertion along with MnO_(2) dissolution/deposition at the cathode.After the modification,Na-MnO_(2) battery exhibits a discharge capacity of 267.10 mA h/g and a cell voltage of 3.30 V(vs.Na/Na^(+)),resulting in a high specific energy density of 881.43 Wh/kg.After 300 cycles,the battery retains 98% of its first-cycle discharge capacity with100% coulombic efficiency.Besides,Na metal-free battery assembled using sodium biphenyl as a safer anode also delivers an excellent energy density of 810.0 Wh/kg.This work could provide a feasible method to develop an advanced Na-MnO_(2) battery for real-time energy storage applications.

Nucleoside modified mRNA-lipid nanoparticles as a new delivery platform for the repair of the injured spinal cord

Spinal cord injury and treatment opportunities:The adult mammalian spinal cord has a very limited capacity for spontaneous regeneration due to various intrinsic molecular and cellular factors.Although the spinal cord neurons have the capacity to regenerate their axons,the expression of growth inhibitory factors,lack or suppression of proper guidance cues,and profound inflammatory responses do not permit successful regeneration(Khyeam et al.,2021).

Effect of Modified Biochar with Organic Fertiliser on the Growth and Development of Chinese Rose

In order to reduce the waste of resources and environmental pollution caused by excessive application of chemical fertilizers, improve the utilization rate of fertilizers, and promote the large-scale and high-quality development of the Chinese rose industry. In this experiment, corn stover biochar, phosphoric acid modified biochar and organic fertilizer were used as test materials, and the effects of mixed application of modified biochar and organic fertilizer on the growth and development of Chinese rose as well as soil physicochemical properties were investigated by using the method of pot planting test. The results showed that modified biochar with organic fertilizer had the most significant effect on the enhancement of soil pH, organic matter content and soil carbon-to-nitrogen ratio. After 120 d of planting, modified biochar with organic fertilizer had the most significant effect on the enhancement of plant height and crown width of Chinese rose;both organic fertilizer and modified biochar with organic fertilizer significantly increased the chlorophyll content of Chinese rose. The number of flowers and the number of branches were the highest in the modified biochar with organic fertilizer treatment. In conclusion, the application of modified biochar with organic fertilizer can better improve the soil pH, and increase the soil organic matter content and carbon-to-nitrogen ratio to change the biological traits of Chinese rose. The results of this study provide a theoretical basis for the reduction of chemical fertilizers and the resource utilization of agricultural wastes and guarantee the sustainable development of the cut flower industry.

Trends in the global commercialization of genetically modified crops in 2023

The commercialization of genetically modified(GM)crops has increased food production,improved crop quality,reduced pesticide use,promoted changes in agricultural production methods,and become an important new production strategy for dealing with insect pests and weeds while reducing the cultivated land area.This article provides a comprehensive examination of the global distribution of GM crops in 2023.It discusses the internal factors that are driving their adoption,such as the increasing number of GM crops and the growing variety of commodities.This article also provides information support and application guidance for the new developments in global agricultural science and technology.

Multi-soliton solutions, breather-like and bound-state solitons for complex modified Korteweg–de Vries equation in optical fibers

Under investigation in this paper is a complex modified Korteweg–de Vries(KdV) equation, which describes the propagation of short pulses in optical fibers. Bilinear forms and multi-soliton solutions are obtained through the Hirota method and symbolic computation. Breather-like and bound-state solitons are constructed in which the signs of the imaginary parts of the complex wave numbers and the initial separations of the two parallel solitons are important factors for the interaction patterns. The periodic structures and position-induced phase shift of some solutions are introduced.

Fatigue Resistance of RCA Modified Asphalt Based on Dielectric Properties

In order to study the anti-fatigue performance of RCA modified asphalt (RMA),the performance of RMA and 90#matrix asphalt with different modifier content were measured by asphalt penetration,ductility,softening point,Brookfield viscosity,rheological index,infrared spectrum and dielectric constant test.This paper discusses the changes of asphalt basic indexes,fatigue properties and asphalt components based on dielectric properties under different modifier contents,and analyzes the grey correlation degree between components and asphalt pavement performance indexes.The results show that the optimum content of RCA modifier is 16.7%of the asphalt quality according to the penetration,ductility,softening point,Brockfield viscosity,viscosity temperature curve and fatigue life.In the phase angle-strain curve,there is disorder in the latter part of the curve.According to the strain (ε_(d)) corresponding to the disorder point,a new fatigue failure criterion is proposed and proved.Based on the new asphalt fatigue failure criterion,the fatigue prediction model of asphalt mixture is improved,and the fatigue life predicted by the improved fatigue model is compared with the fatigue life obtained by four-point bending fatigue test.The results show that the proposed new asphalt fatigue failure criterion is reasonable,and the fatigue life predicted by the improved asphalt mixture fatigue prediction model is accurate.The research method of classifying asphalt components based on dielectric properties is simple and effective,and the components have a high correlation with the road performance of base asphalt and modified asphalt.

Investigation of granite failure precursor under axial load using modified LSTM framework

Granite is usually composed of quartz,biotite,feldspar,and cracks,and the variation characteristics of these components could reflect the deformation and failure process of rock well.Taking granite as an example,the video camera was used to record the deformation and failure process of rock.The distribution of meso-components in video images was then identified.The meso-components of rock failure precursors were also discussed.Moreover,a modified LSTM(long short-term memory method)based on SSA(sparrow search algorithm)was proposed to estimate the change of meso-components of rock failure precursor.It shows that the initiation and expansion of cracks are mainly caused by feldspar and quartz fracture,and when the quartz and feldspar exit the stress framework,rock failure occurs;the second large increase of crack area and the second large decrease of quartz or feldspar area may be used as a precursor of rock failure;the precursor time of rock failure based on meso-scopic components is about 4 s earlier than that observed by the naked eye;the modified LSTM network has the strongest estimation ability for quartz area change,followed by feldspar and biotite,and has the worst estimation ability for cracks;when using the modified LSTM network to predict the precursors of rock instability and failure,quartz and feldspar could be given priority.The results presented herein may provide reference in the investigation of rock failure mechanism.

Modified Xiaoyao powder for postpartum depression:A systematic review and meta-analysis

Objective:To evaluate the effectiveness and safety of modified Xiaoyao powder for postpartum depression(PPD)by conducting a systematic review of randomized controlled trials(RCTs).Methods:The Chinese National Knowledge Infrastructure Databases(CNKI),the Chinese Scientific Journals Database(VIP),Wanfang,Google Scholar,the SinoMed,Embase,Cochrane Library,and PubMed databases were searched from their inception to April 25,2023.The Cochrane Risk of Bias tool was used to assess the quality of the trials.We applied the risk ratio to present dichotomous data and the mean difference to present continuous data.Data with similar characteristics were pooled for meta-analysis and heterogeneity was assessed using I2.Results:This review included 35 trials involving 2848 participants.The quality of the included studies was low(unclear randomization processes and insufficient reporting of blinding).Participants treated with modified Xiaoyao powder plus Western medicine showed lower Hamilton Depression Scale(HAMD)depression score than those who used Western medicine alone(mean difference=-2.15;95%confidence interval:-2.52 to 1.78;P<.00001),and higher effective rate(relative risk=1.19;95%confidence interval:1.15 to 1.24;P<.00001),When comparing modified Xiaoyao alone with Western medicine,the HAMD depression score remained low,however,the efficacy rate was higher in the modified Xiaoyao group.Regarding adverse events,the modified Xiaoyao group reported weight gain,nausea,and diarrhea,but no severe adverse events were reported.Conclusion:Modified Xiaoyao may help relieve depression in PPD when used alone or in combination with Western medicine,with minor side effects.Therefore,future high-quality,large-sample size RCTs are warranted.

Preparation of Modified UiO-66 Catalyst and Its Catalytic Performance for NH_(3)-SCR Denitration

Zirconium-based metal-organic framework UiO-66 was successfully prepared by solvothermal method,and UiO-66 was modified by adding regulators such as formic acid,acetic acid,and hydrochloric acid.The NH_(3)-SCR reactivity of the samples was evaluated by the denitration activity evaluation system,and the UiO-66 and the regulator-modified UiO-66 were characterized by XRD,SEM,BET,FTIR,TG,NH_(3)-TPD,etc.,the effects of regulator types on the structure and properties of UiO-66 were investigated.The experimental results show that,after adding the modifier,the morphology of UiO-66 changes from irregular quadrilateral with serious agglomeration to particles with regular crystal shape and good dispersibility,and the crystal morphology of the catalyst is improved.In addition,after adding the modifier,UiO-66 has a larger specific surface area and stronger surface acidity,which optimizes the catalytic performance of UiO-66.The catalytic performance test results of NH_(3)-SCR show that the low-temperature activity of UiO-66 is poor,and it only shows a certain catalytic activity at higher temperatures.The catalytic activity of UiO-66 was significantly improved after adding the regulator.Among them,the UiO-66-HCl modified with hydrochloric acid had the best catalytic activity,and the denitration rate reached 70%when the denitration temperature was 380℃.

A Modified Iterative Learning Control Approach for the Active Suppression of Rotor Vibration Induced by Coupled Unbalance and Misalignment

This paper proposes a modified iterative learning control(MILC)periodical feedback-feedforward algorithm to reduce the vibration of a rotor caused by coupled unbalance and parallel misalignment.The control of the vibration of the rotor is provided by an active magnetic actuator(AMA).The iterative gain of the MILC algorithm here presented has a self-adjustment based on the magnitude of the vibration.Notch filters are adopted to extract the synchronous(1×Ω)and twice rotational frequency(2×Ω)components of the rotor vibration.Both the notch frequency of the filter and the size of feedforward storage used during the experiment have a real-time adaptation to the rotational speed.The method proposed in this work can provide effective suppression of the vibration of the rotor in case of sudden changes or fluctuations of the rotor speed.Simulations and experiments using the MILC algorithm proposed here are carried out and give evidence to the feasibility and robustness of the technique proposed.

Clinical efficacy of modified Kamikawa anastomosis in patients with laparoscopic proximal gastrectomy

BACKGROUND With the increasing incidence of proximal gastric cancer,laparoscopic proximal gastrectomy has been applied.However,reflux esophagitis often occurs after traditional esophagogastric anastomosis.In order to solve this problem,several methods of digestive tract reconstruction have emerged,but the most satisfying method remains to be discussed.Therefore,we modified traditional Kamikawa anastomosis to investigate the appropriate digestive tract reconstruction in laparo-scopic proximal gastrectomy.All the patients were successfully operated on without conversion to laparotomy.The duration of operation and digestive tract reconstruction were 203.500(150-224)min and 87.500(73-111)min,respectively.The intraoperative amount of bleeding was 20.500 mL±0.696 mL.The time of postoperative first flatus,the first postoperative fluid intake,and the postoperative length of stay were 2(1-3)d,4(3-5)d,and 9(8-10)d,respectively.All the patients were followed up for 12-23 months.The body mass index at 6 and 12 months after surgery were 22.577 kg/m2±3.098 kg/m2 and 22.594 kg/m2±3.207 kg/m2,respectively.The nutrition risk screening 2002 score,the patient-generated subjective global assessment score,and the gastroesophageal reflux disease scale score were good at 6 and 12 months after surgery.Reflux esophagitis and anastomotic stenosis were not observed in any of the patients during their 12-month postoperative gastroscopy or upper gastrointestinal tract visits.All the patients exhibited no tumor recurrence or metastasis.CONCLUSION The modified Kamikawa anastomosis is safe and feasible for laparoscopic proximal gastrectomy and has good antireflux effects and nutritional status.

Modified intratympanic steroid therapy for sudden sensorineural hearing loss via tympanic tube and gelfoam as a salvage treatment

Background: Sudden sensorineural hearing loss(SSNHL) is a prevalent emergency in ear, nose, and throat practice. Previous studies have demonstrated that intratympanic steroid therapy(IST) can serve as a salvage treatment for SSNHL after the failure of systemic steroid therapy(SST).Objective: This study aimed to analyze the efficacy of modified IST involving the insertion of a tympanic tube and gelfoam as a salvage treatment for patients with SSNHL, and to explore its associated factors.Methods: Totally, 74 patients who were aged 22–81 years with SSNHL were enrolled and allocated to either the control group(n = 25) or the treatment group(n = 49) based on their treatment modalities. All patients received SST lasting for at least 7 days. Subsequently, patients in the treatment group, after SST failure, underwent IST twice a week for 2–6 weeks, while the control group did not. Efficacy was assessed by the improvement in pure tone average at the affected frequency at the beginning and end of IST.Results: Hearing improvement in all patients after IST in the treatment group was 9.71 ± 14.84 dB, with significant improvement at affected frequencies(250-8000 Hz) compared with the control group(P < 0.05). The findings indicated the duration from the onset of SSNHL to the beginning of IST as an independent factor for pure tone average improvement after treatment(P = 0.002), whereas age, duration of SST, and time of IST were not(P > 0.05).Conclusion: The modified IST was demonstrated to be a safe and effective method as a salvage treatment for SSNHL. This study explored the efficacy of a modified IST approach, incorporating the utilization of tympanic tubes and gelfoam as key components. The findings underscore the advantages of gelfoam as a strategic drug carrier placed in the round window niche. By minimizing drug loss, extending action time, and increasing perilymph concentration, gelfoam enhances the therapeutic impact of IST, contributing to improved hearing outcomes in patients with SSNHL.

A Glassy Carbon Electrode Modified with Cellulose Nanofibrils from Ammophila arenaria for the Sensitive Detection of L-Trytophan

L-tryptophan is an essential amino acid for human health. Nanofibrillated cellulose (NFC) from marram grass (Ammophila arenaria) extracted from plants harvested in the center of Tunisia was used for the first time for the modification of a glassy carbon electrode (GCE), for the sensitive detection of L-tryptophan (Trp). After spectroscopic and morphological characterization of the extracted NFC, the GC electrode modification was monitored through cyclic voltammetry. The NFC-modified electrode exhibited good analytical performance in detecting Trp with a wide linear range between 7.5 × 10−4 mM and 10−2 mM, a detection limit of 0.2 µM, and a high sensitivity of 140.0 µA∙mM−1. Additionally, the NFC/GCE showed a good reproducibility, good selectivity versus other amino acids, uric acid, ascorbic acid, and good applicability to the detection of Trp in urine samples.

Novel wood-plastic composite fabricated via modified steel slag:Preparation,mechanical and flammability properties

A novel method was developed to enhance the utilization rate of steel slag(SS).Through treatment of SS with phosphoric acid and aminopropyl triethoxysilane(KH550),we obtained modified SS(MSS),which was used to prepare MSS/wood-plastic composites(MSS/WPCs)by replacing talcum powder(TP).The composites were fabricated through melting blending and hot pressing.Their mechanical and combustion properties,which comprise heat release,smoke release,and thermal stability,were systematically investigated.MSS can improve the mechanical strength of the composites through grafting reactions between wood powder and thermoplastics.Notably,MSS/WPC#50(16wt%MSS)with an MSS-to-TP mass ratio of 1:1 exhibited optimal comprehensive performance.Compared with those of WPC#0 without MSS,the tensile,flexural,and impact strengths of MSS/WPC#50 were increased by 18.5%,12.8%,and 18.0%,respectively.Moreover,the MSS/WPC#50 sample achieved the highest limited oxygen index of 22.5%,the highest vertical burning rating at the V-1 level,and the lowest horizontal burning rate at 44.2 mm/min.The formation of a dense and stable char layer led to improved thermal stability and a considerable reduction in heat and smoke releases of MSS/WPC#50.However,the partial replacement of TP with MSS slightly compromised the mechanical and flame-retardant properties,possibly due to the weak grafting caused by SS powder agglomeration.These findings suggest the suitability of MSS/WPCs for high-value-added applications as decorative panels indoors or outdoors.