Synthesis and Characterization of Y-Doped Mesoporous CeO_2 Using A Chemical Precipitation Method

Using cetyltrimethylammonium bromide （CTAB） as the template agent, cerium nitrate as the cerium resource, yttrium nitrate as the yttrium resource, and ammonium carbonate as the precipitating agent, mesoporous CeO2 powders doped with different yttrium contents were successfully synthesized using a chemical precipitation method, under an alkalescent condition. Properties of the obtained samples were characterized and analyzed with X-ray diffraction （XRD）, energy dispersive analysis of X-rays （EDAX）, transmission electron microscopy （TEM）, infrared （IR） absorbance, and the BET method. For the prepared samples with 20% （molar ratio） Y-doped content, a BET specific surface area of 106. 6 m^2 · g^- 1, with an average pore size of3~27 nm were obtained. XRD patterns showed that the doped samples were with a cubic fluorite structure. TEM micrographs revealed that the doped samples showed a spherical morphology with a diameter ranging from 20 to 30 nm and a round pore shape. IR results indicated that the Ce-O-Ce vibration intensity decreased as the Y-doped content increased. N2 adsorption-desorption isotherms showed that the samples possessed typical mesopore characteristics. The average pore size of the samples decreased alter mesoporous CeO2 was doped with yttrium, and the average pore size decreased largely as the Y-doped content increased.

Synthesis of γ-Al_2O_3 nanoparticles by chemical precipitation method

Highly pure active γ-Al2O3 nanoparticles were synthesized from aluminum nitrate and ammonium carbonate with a little surfactant by chemical precipitation method. The factors affecting the synthesis process were studied. The properties of γ-Al2O3 nanoparticles were characterized by DTA, XRD, BET, TEM, laser granularity analysis and impurity content analysis. The results show that the amorphous precursor AI（OH）3 sols are produced by using 0.1 mol/L Al（NO3）3·9H2O and 0.16 mol/L （NH4）2CO3·H2O reaction solutions, according to the volume ratio 1.33, adding 0.024%（volume fraction） surfactant PEG600, and reacting at 40℃, 1000 r/min stirring rate for 15min. Then, after stabilizing for 24 h, the precursors were extracted and filtrated by vacuum, washed thoroughly with deionized water and dehydrated ethanol, dried in vacuum at 80℃ for 8h, final calcined at 800℃ for 1h in the air, and high purity active γ-Al2O3 nanoparticles can be prepared with cubic in crystal system, OH^7-FD3M in space group, about 9 nm in crystal grain size, about 20 nm in particle size and uniform size distribution, 131.35 m^2/g in BET specific surface area, 7 - 11 nm in pore diameter, and not lower than 99.93% in purity.

Effects of Heating Processing on Microstructure and Magnetic Properties of Mn-Zn Ferrites Prepared via Chemical Co-precipitation

The fine powders of Mn-Zn ferrites with uniform size were prepared via chemical co- precipitation method. X-ray diffraction analysis （XRD）, scanning electron microscopy （SEM）, vibrating sample magnetometer （VSM）, frequency dependence of permeability and metallographical microscope were used to investigate the crystal structure, surface topography and magnetic properties of the powders and the sintering samples. The experimental results demonstrate that the precursor powders have formed a pure phase cubic spinel MnxZn1-xfe2O4 while in the reactor and show definite magnetism, which can solve the difficult issue in washing process effectively. When calcined beneath 450 ℃, the powders have intact crystal form and the crystallite size is less than 20 nm. Comparison tests of sintering temperatures show that 1 300 ℃ is the ideal sintering temperature for Mn-Zn ferrites prepared by using the chemical co-precipitation.

Influence of chemical composition and cold deformation on aging precipitation behavior of high nitrogen austenitic stainless steels

The influence of chemical composition and cold deformation on aging precipitation behavior of 18Cr-16Mn-2Mo-I.IN （HNS-A）, 18Cr-16Mn-I.3N （HNS-B）, 18Cr-18Mn-2Mo-0.96N （HNS-C） and 18Cr-18Mn-2Mo-0.77N （I-INS-D） high nitrogen austenitic stainless steels was investigated. The results show that the ＂nose＂ temperatures and incubation periods of the initial time-temperature-precipitation （TTP） curves of aged HNSs are found to be 850 ℃, 60 s; 850 ℃, 45 s; 850 ℃, 60 s and 900 ℃, 90 s, respectively. Based on the analysis of SAD patterns, the coarse cellular Cr2N precipitate which presents a lamellar structure has a hexagonal structure of a=0.478 nm and c=0.444 nm. The Z phase corresponding to a composition of Fe36Cr^2Mo10, is determined to be a body-centered cubic structure ofa=0.892 nm. The precipitating sensitivity presents no more difference with the nitrogen content increasing from 0.77% to 0.96%, but exhibits so obviously that the cellular precipitates nearly overspread the whole field. The addition of Mo element can restrain the TTP curves moving left and down, which means decreasing the sensitivity of aging precipitation. With increasing the cold deformation, the sensitivity of precipitation increases obviously.

Treatment of Wet FGD Wastewater by a Modified Chemical Precipitation Method Using a Solid Powder Reagent

This research focused on developing a modified chemical precipitation (MCP) method for treating wet flue gas desulfurization (FGD) waste water by adding a solid powder reagent directly. Simulated wet FGD wastewater was treated by MCP method in simulation experiments. Optimization experiments were carried out with the help of response surface methodology (RSM) and central composite design (CCD) to evaluate the effects and the interactions of experimental variables, including reagent dosage, temperature and pH value. The optimal reagent dosage, temperature and pH value were 3018.0 mg/L, 40.5 °C and 5.7, respectively. The RSM was demonstrated as an appropriate approach for the optimization of wet FGD wastewater treatment with the MCP method. A comparative study between the MCP method and the traditional chemical precipitation (TCP) method on raw wet FGD wastewater treatment was conducted. Results indicate that the MCP had less reagent dosage and variety than the TCP method had. Thus, the MCP method had a lower cost. © 2017, Tianjin University and Springer-Verlag Berlin Heidelberg.

Analysis of chemical composition of precipitation in a typical background site

background precipitation in Lijiang, China was investigated. Results showed that the chemical composition of atmospheric background precipitation mainly comes from fly ash and continental atmospheric transfer, and does not have any obvious correlation with oceanic aerosol, taking Amsterdam in the Pacific Ocean and St. Georges in the Atlantic Ocean and Katherine, Australia as examples for analysing.

Chemical characteristics of precipitation and wet deposition of major ions in Liaozhong County of Liaoning Province,Northeast China

The chemical characteristics of precipitation were analyzed based on the chemical composition of principal ionic within acid rain(from February 2007 to January 2008)of Liaozhong Meteorological Station located in Malong Village in Liaozhong County of Northeast China,meteorological conditions on the corresponding period ground,and variation of several air pollutants concentration.The results indicated that:(1)The precipitation average pH value of all samples was4.76;the frequency of acid rain during the observation period was 70.7%;the frequency was 82.8%in summer and autumn.(2)In the chemical composition of precipitation,the primary anions were SO_4^(2-)and NO_3^-;the primary cations were NH_4^+and Ca^(2+).(3)All concentration of anions was higher in summer and winter,but relatively low in spring and autumn.This showed that the relationship between regional rainfall acidification and pollution was not significant.(4)Rainwater acidity and nearly floor gaseous pollution concentration were different from each other,and pH and NO_x,CO,NO_2 and O_3concentrations showed significant negative correlation,but was not obvious with SO_2 concentration.However,the pH and alkaline pollutants,such as particulate,was positively correlative.

Gas sensitive properties of nanometer materials In_2O_3 synthesized by chemical precipitation

In2O3 nanoparticles were prepared from or with different indium salts by chemical precipitation under the conditions of various pH values. The crystal structure and ceramic microstructure of the samples were characterized by X-ray diffraction （XRD） and transmission electron microscopy （TEM）. The results show that the mean grain size of In2O3 is less than 100 nm, and their particle homogeneity and dispersibility are satisfactory. The gas sensitivity defined as Ra/Rg was detected in a static system. The results show that the sensors made by as-prepared nanoparticles has high sensitivity to many gases such as alcohol, HCHO, NH3 , et al. The response time is less than 20 s and the recovery time is lower than 30 s.

Effect of Molybdenum Doping on Oxygen Permeation Properties and Chemical Stability of SrCo0.8Fe0.2O3-δ

The phase composition, microstructure, thermal expansion coefficients, oxygen permeation properties and chemical stability of SrCo0.8Fe0.2O3-δ （SCFM） were investigated and compared with those of SrCo0.8Fe0.2O3-δ（SCF）. Single phase SCFM was successfully prepared by a combined EDTA-citric method. SCFM shows a lower thermal expansion coefficient （24× 10^-6-29× 10^-6/K） than SCF between 500 and 1050 ℃, indicating a more stable structure. SCFM shows a high oxygen permeation flux, although the oxygen flux of SCFM decreases slightly because of Mo dopant. Furthermore, it was demonstrated that the doping of Mo in SCF can prevent the order-disorder transition and improves the chemical stability to CO2.

INTERACTION OF PRECIPITATION AND RECRYSTALLIZATION IN RAPIDLY SOLIDIFIED Cu-Cr-Zr-Mg ALLOY

The recrystallization process of a rapidly solidified Cu-Cr-Zr-Mg alloy during its aging was investigate experimentally. It was found that (1) upon aging, the precipitation process takes place prior to recrystallization for the cold-deformed Cu-Cr-Zr-Mg alloy produced by rapid solidification, and the precipitates have a restrained effect on the following recrystallization process; (2) the hindrance of the dispersed fine precipitates to the common recrystallization leads to the simultaneous in situ and discontinuous recrystallization; (3) the resolution of the precipitates in the front of migrating grain boundaries takes place during the nucleation and growth of recrystallization, which results in a supersaturation in the recrystallized zones, while the re-precipitation of the supersaturated solute atoms in vacancies further increases the dispersion hardening effect.

PRECIPITATION HARDENING IN B2-ORDERED NiAl BY Ni_(2)AlTi COMPOUND

Microstructural variations and correlated hardness changes in B2-ordered NiAl containing fine precipitation of Ni2AlTi have been investigated by means of transmission electron microscopy (TEM) and hardness tests. The amount of age hardening is not large as compared to the large microstructural variations during aging. TEM observations have revealed that the L21-type Ni2AlTi precipitates keep a lattice coherency with the NiAl matrix at the beginning of aging. By longer periods of aging Ni2AlTi precipitates lose their coherency and change their morphology to the globular ones surrounded by misfit dislocations. The temperature dependence of the yield strength of precipitate-containing B2-ordered NiAl was investigated by compression tests over the temperature range of 873-1273 K. The fine precipitation of Ni2AlTi was found to enhance greatly the yield strength and the high-temperature strength is comparable with that of superalloy Mar-M200.

Improvement of 6–15 Day Precipitation Forecasts Using a Time-Lagged Ensemble Method

A time-lagged ensemble method is used to improve 6-15 day precipitation forecasts from the Beijing Climate Center Atmospheric General Circulation Model,version 2.0.1.The approach averages the deterministic predictions of precipitation from the most recent model run and from earlier runs,all at the same forecast valid time.This lagged average forecast （LAF） method assigns equal weight to each ensemble member and produces a forecast by taking the ensemble mean.Our analyses of the Equitable Threat Score,the Hanssen and Kuipers Score,and the frequency bias indicate that the LAF using five members at time-lagged intervals of 6 h improves 6-15 day forecasts of precipitation frequency above 1 mm d-1 and 5 mm d-1 in many regions of China,and is more effective than the LAF method with selection of the time-lagged interval of 12 or 24 h between ensemble members.In particular,significant improvements are seen over regions where the frequencies of rainfall days are higher than about 40％-50％ in the summer season; these regions include northeastern and central to southern China,and the southeastem Tibetan Plateau.

Effect of Chemical Doping and Ion Implantation on Cond uctivity of Poly(p-phenylene vinylene) Derivatives

The surface conductivity of poly [ 2-methoxy-5-（3＇-methyl） butoxy]-p-phenylene vinylene （PMOMBOPV） films doped with FeCl3 and H2SO4 by chemical method and implanted by N^＋ ions was studied and the comparison of environmental stability of conductive behavior was also investigated. The energy and dose of N^＋ ions were in the rang 15～35 keV and 3. 8×10^15～9. 6×10^16 ions/cm^2, respectively. The conductivity of PMOMBOPV film was enhanced remarkably with the increases of the energy and dose of N^＋ ions. For example, the conductivity of PMOMBOPV film was 3. 2×10^-2S/cm when ion implantation was performed with an energy of 35 keV at a dose of 9. 6 × 10^14 ions/cm^2 , which was almost seven orders of magnitude higher than that of film unimplanted. The environmental stability of conductive behavior for ionimplanted film was much better than that of chemical doped films. Moreover, the conductive activation energy of ion-implanted films was measured to be about 0.17 eV.

Soil Chemical Property Changes over Time from Struvite Compared to Other Fertilizer-Phosphorus Sources in Multiple Soils

Studies have shown that phosphorus (P) recovered from wastewater as the mineral struvite [MgNH4PO4·6(H2O)] may be a viable alternative fertilizer-P source. This study aimed to compare the effectiveness of electrochemically precipitated struvite (ECST), reclaimed from synthetic wastewater, to other commercial fertilizer-P sources in cultivated soils from Arkansas [AR;silt loam (SiL) and loam (L)], Missouri (MO;SiL), and Nebraska [NE;SiL and sandy loam (SL)]. A plant-less, moist-soil incubation experiment, including ECST, chemically precipitated struvite (CPST), monoammonium phosphate (MAP), triple superphosphate (TSP), and an unamended control (UC), was conducted to quantify soil pH, nitrate (NO3-N), ammonium (NH4-N), and Mehlich-3 (M3)-P, -Ca, -Mg, and -Fe concentrations at 0.5, 1, 2, 4, and 6 months. All measured soil properties differed (P ·kg-1 for AR-L-TSP after 1 month and NE-SiL-MAP after 6 months, respectively. Soil M3-P ranged from -29.6 mg·kg-1 in the AR-L-UC after 1 month to 429 mg·kg-1 AR-SiL-TSP after 0.5 months. Results showed that, over time, ECST had comparable pH and soil NO3-N, NH4-N, and M3-P, -Ca, -Mg, and -Fe behavior compared to CPST, MAP, and TSP across various soil textures.

The Application of Air-flow to the Technological Process of Chemical Fiber

The air-flow’s states and ways acted on the technological process of chemical fiber are summed up, which includes chip drying, spinning quenching as well as airjet texturing (air texturing, tangling texturing and bulked continuous filament (BCF)),and the effect of air-flow on the process and quality of chemical fiber is studied,and the action of mechanics and heat on the bulked continuous filament are calculated.

A Novel β-1,4-N, 6-O-Diacetylmuramidase from Streptomyces griseus and its Chemical Modification

A novel lysozyme named β-1, 4-N, 6-O-diacetylmuramidase R2 was purified and characterized from Streptomyces griseus. The molecular weight of the enzyme was determined by MALDI-TOF-MS as 23.5 kDa. The N-terminal amino acid sequence was DTSGVQGIDVSHWQG. Chemical modification of β-1, 4-N, 6-O-diacetylmuramidase R2 indicated that sulfhydryl group and carbamidine of arginine residues are not essential for the activity of the enzyme, but lysine residues and imidazole of histidine residues are essential for the activity. The number of essential tryptophan and carboxyl groups was found that only one tryptophan residue and three carboxyl groups in the active site.

Improved continuous precipitation kinetics and tensile properties of extruded AZ80 alloy through {10-12} twin formation

This study investigates the effect of{10-12}deformation twins on the continuous precipitation behavior of an extruded Mg-8.0Al-0.5Zn-0.2Mn(AZ80)alloy during aging.The extruded AZ80 alloy is compressed along the transverse direction to introduce{10-12}twins,followed by an aging treatment at 300℃.The extruded material exhibits a twin-free microstructure with low internal strain energy,whereas the pre-twinned material possesses abundant{10-12}twins and has high internal strain energy.The aging results reveal that the peak-aging time of the pre-twinned material(1 h)is one-eighth of that of the extruded material(8 h).Although Mg_(17)Al_(12)continuous precipitates(CPs)are observed in both the peak-aged materials,these CPs are much smaller and more densely distributed in the pre-twinned material despite the significantly shorter aging time.The CPs size in the peak-aged materials increases in the following order:twinned region in the pre-twinned material(0.47μm)<residual matrix region in the pre-twinned material(1.71μm)<matrix region in the extruded material(2.55μm).Moreover,the CPs number density in the twinned region of the pre-twinned material is approximately 11 times higher than that in the matrix region of the extruded material.The peak-aged pre-twinned material exhibits significantly higher tensile strength and ductility than the peak-aged extruded material.These results demonstrate that the formation of{10-12}twins in the extruded AZ80 alloy substantially accelerates the static precipitation of CPs during aging at 300℃and improves the tensile properties of the peak-aged material.

Electrochemical Behavior and Its Electrocatalytic Activity of A P-Mo Heteropolyanion Modified ITO Electrode

s: A new method for the preparation of an organic-inorganic composite film of the heteropolyanion has been developed by modifying P(Mo2O7)6-7 to the indium tin oxide (ITO) electrode surface. The modified electrode displayed a strong catalytic activity towards the reduction of IO3-. In the range of 1.0?0-6~5?0-4mol/L, the catalytic current was linear proportional to the IO3- concentration.

Controlled Synthesis of Dental Enamel-like Hydroxyapatite Whiskers via Hydrothermal Homogeneous Precipitation

Dental enamel-like hydroxyapatite whiskers with high crystallinity and homogeneous morphology were synthesized by a hydrothermal homogeneous precipitation method.The composition,crystallinity and morphology of prepared hydroxyapatite whiskers were characterized by Ⅹ-ray diffraction and scanning electron microscopy.The effects of urea and sorbitol on their morphology and composition were investigated.Homogeneous and well crystallized enamel-like hydroxyapatite whiskers with 1.17±0.08 μm in length and 84± 14 nm in width were obtained at 0.80 mol · L-1 urea and 0.26 mol · L-1 sorbitol.These hydroxyapatite whiskers may be close to nature hydroxyapatite dental enamel in terms of the morphology and composition,suggesting that they could have potential application as dental restorative materials in the field of stomatology.