Determination of Nickel and Palladium in Environmental Samples by Low Temperature ETV-ICP-OES Coupled with Liquid-liquid Extraction with Dimethylglyoxime as Both Extractant and Chemical Modifier

A novel method for the determination of nickel and palladium in environmental samples by low temperature ETV-ICP-OES with dimethylglyoxime（DMG） as both the extractant and chemical modifier has been developed. In this study, it was found that nickel and palladium can form complexes with dimethylglyoxime（0. 05%, mass fraction） at pH 6.0 and can be extracted into chloroform quantitatively. The complexes can be evaporated into plasma at a suita-ble temperature（ 1400℃） for ICP-OES detection. Under the optimized conditions, the detection limits of nickel and palladium are 0.48 and 0. 40 ng/mL, respectively, while the RSD values are separately 5.0% and 3.1% （p = 50 ng/mL, n = 7）. The proposed method was applied to the determination of the target analytes in environmental sam-ples with satisfactory results.

A Glassy Carbon Electrode Modified with Cellulose Nanofibrils from Ammophila arenaria for the Sensitive Detection of L-Trytophan

L-tryptophan is an essential amino acid for human health. Nanofibrillated cellulose (NFC) from marram grass (Ammophila arenaria) extracted from plants harvested in the center of Tunisia was used for the first time for the modification of a glassy carbon electrode (GCE), for the sensitive detection of L-tryptophan (Trp). After spectroscopic and morphological characterization of the extracted NFC, the GC electrode modification was monitored through cyclic voltammetry. The NFC-modified electrode exhibited good analytical performance in detecting Trp with a wide linear range between 7.5 × 10−4 mM and 10−2 mM, a detection limit of 0.2 µM, and a high sensitivity of 140.0 µA∙mM−1. Additionally, the NFC/GCE showed a good reproducibility, good selectivity versus other amino acids, uric acid, ascorbic acid, and good applicability to the detection of Trp in urine samples.

Study of the electrochemical properties of a transition metallic ions modified electrode in acidic VOSO_4 solution

Graphite material was used as the electrode for an all-vanadium redox flow battery, and the electrode was modified by transition metallic ions to enhance its electrochemical behavior. An porous graphite composite electrode has high specific surface area and high current density. The electrode modified by transition metallic ions has improved catalysis behavior that can catalyze the V（Ⅱ）-V（Ⅴ） redox reaction showed by cyclic voltammograms. This article studied the impedance of the modified electrode by electrochemical impedance spectroscopy （EIS）, and approved that the electrode modified by Co^2＋ and Mn^2＋ has a lower charge transfer resistance than the non-modified electrode. The effect of average particle size distribution is at lower frequencies that the slope of Warburg impedance is reduced by large particle size distribution. The voltage efficiency of the Co^2＋ modified electrode test cell is 81.5%, which is higher than that of the non-modified electrode.

Bi_(2)O_(3)/ZnO nanocomposite:Synthesis,characterizations and its application in electrochemical detection of balofloxacin as an antibiotic drug

In the present work,a chemically modified electrode has been fabricated utilizing Bi_(2)O_(3)/ZnO nanocomposite.The nanocomposite was synthesized by simple sonochemical method and characterized for its structural and morphological properties by using XRD,FESEM,EDAX,HRTEM and XPS techniques.The results clearly indicated co-existence of Bi_(2)O_(3) and ZnO in the nanocomposite with chemical interaction between them.Bi_(2)O_(3)/ZnO nanocomposite based glassy carbon electrode(GCE)was utilized for sensitive voltammetric detection of an anti-biotic drug(balofloxacin).The modification amplified the electroactive surface area of the sensor,thus providing more sites for oxidation of analyte.Cyclic and square wave voltammograms revealed that Bi_(2)O_(3)/ZnO modified electrode provides excellent electrocatalytic action towards balofloxacin oxidation.The current exhibited a wide linear response in concentration range of 150e1000 nM and detection limit of 40.5 nM was attained.The modified electrode offered advantages in terms of simplicity of preparation,fair stability(RSD 1.45%),appreciable reproducibility(RSD 2.03%)and selectivity.The proposed sensor was applied for determining balofloxacin in commercial pharmaceutical formulations and blood serum samples with the mean recoveries of 99.09% and 99.5%,respectively.

Electrochemical Properties of Polypyrrole-Coated Microelectrode Array and the Fabrication of Polypyrrole-Based Microelectronic Devices

Conducting polymers have been studied extensively. An interesting property of the conducting polymer is that the conductivity of some polymers, such as polypyrrolc, polyaniline, poly(3-methylthiophene) etc. , is affected by the voltage applied to them. For polypyrrole, the oxidized state is an electronic conductor and the reduced state is essentially insulating. Using this property, one can fabricate the polymer-based electronic devices. Experimental results of Pickun

Chemically Modified Chitosan Beads as Molecularly Imprinted Polymer Matrix for Adsorptive Separation of Proteins

In a phosphate buffer, a hemoglobin (Hb)-imprinted polymer complex was prepared using maleic anhydride (MAH) modified chitosan beads as matrix, acrylamide (AM) as functional monomer, N,N-methylenebisacrylamide (MBA) as cross-linker and potassiumpersulfate (KPS) / sodium hydrogen sulfite (NaHSO3) as initiators. Langmuir analysis showed that an equal class of adsorption was formed in the molecular imprinting polymer (MIP), and the MIP has high adsorption capacity and selectivity for the imprinted molecule. The MIP can be reused and the recovery was approximately 100% at low concentration.

Performance improvement in polymeric thin film transistors using chemically modified both silver bottom contacts and dielectric surfaces

An efficient interface modification is introduced to improve the performance of polymeric thin film transistors. This efficient interface modification is first achieved by 4-fluorothiophenol（4-FTP） self-assembled monolayers（SAM） to chemically treat the silver source–drain（S/D） contacts while the silicon oxide（SiO2） dielectric interface is further primed by either hexamethyldisilazane（HMDS） or octyltrichlorosilane（OTS-C8）. Results show that contact resistance is the dominant factor that limits the field effect mobility of the PTDPPTFT4 transistors. With proper surface modification applied to both the dielectric surface and the bottom contacts, the field effect mobilities of the bottom-gate bottom-contact PTDPPTFT4 transistors were significantly improved from 0.15 cm^2·V^-1·s^-1 to 0.91 cm^2·V^-1·s^-1.

Highly dispersed Pd nanoparticles on chemically modified graphene with aminophenyl groups for formic acid oxidation

A novel electrode material based on chemically modified graphene （CMG） with aminophenyl groups is covalently functionalized by a nucleophilic ring-opening reaction between the epoxy groups of graphene oxide and the aminophenyl groups of p-phenylenediamine. Palladium nanoparticles with an average diameter of 4.2 nm are deposited on the CMG by a liquid-phase borohydride reduction. The electrocatalytic activity and stability of the Pd/CMG composite towards formic acid oxidation are found to be higher than those of reduced graphene oxide and commercial carbon materials such as Vulcan XC-72 supported Pd electrocatalysts.

A Novel Method of the Preparation ofChemically Modified Electrodes

ＡＮｏｖｅｌＭｅｔｈｏｄｏｆｔｈｅＰｒｅｐａｒａｔｉｏｎｏｆＣｈｅｍｉｃａｌｌｙＭｏｄｉｆｉｅｄＥｌｅｃｔｒｏｄｅｓＬＩＧｅｎ－ｘｉ，ＬＩＡＯＸｉａｎｇ－ｍｉｎ，ＦＡＮＧＨｕｉ－ｑｕｎａｎｄＣＨＥＮＨｏｎｇ－ｙｕａｎ（ＤｅｐａｒｔｍｅｎｔｏｆＣｈｅｍ...

The UV-VIS Studies of C_(60) Chemically Modified Polystyrene Film

The opticai properties of C,, chemicaiiy modified poiystyrene(C,, -PS copolymer) and the parent polystyrene (PS) films have been investigated.Addition of bulky C,, moiety, a special functional group, to the polystyrene by anovel organometallic reaction modified considerably the optical property of theparent polystyrene. The lattice periodicity of pure PS film is subject to someperturbation or distortion in varying degrees due to the covalent attachInent of bulkyC,, moiety to the polymer backbone. C,,-PS copolymer possesses a new energy ba-ndstructure with indirect forbidden band when compared with the parent PS.

Electrochemical Determination of Trace Amounts of Lead (Ⅱ) and Cadmium (Ⅱ) at a Calix[6]arene Modified Carbon Paste Electrode

An electrochemical method for the simultaneous determination of lead(II) and Cadmium(II) with a calix[6]arene modified carbon paste electrode (CPE) has been developed. Pb2+ and Cd2+ were accumulated at the surface of the modified electrode via formation of chemical complexes with calix[6]arene, and reduced at 1.40 V. During the following anodic potential sweep, reduced lead and cadmium were oxidized, and two well-defined striping peaks appeared at about ?0.60 V and ?0.84 V. Compared with a bare carbon paste electrode, the calix[6]arene modified CPE greatly improves the sensitivity of determining lead and cadmium. The stripping peak currents change linearly with the concentration of Pb2+ 3.0×10?8–8.0×10?6 mol·L?1 and with that of Cd2+ 6.0×10?8–1.0×10?5 mol ·L?1. The detection limits of Pb2+ and Cd2+ are found to be 8.0×10?9 mol·L?1 and 2.0×10?8 mol·L?1, respectively. The modified carbon paste electrode was applied to determine trace levels of lead and cadmium in water samples. Comparing with that of atomic absorption spectrometry, the results suggests that the calix[6]arene modified CPE has great potential for the practical sample analysis. Key words lead(II) - cadmium(II) - calix[6]arene - differential pulse stripping voltammetry - chemically modified electrode CLC number O 657.15 Foundation item: Supported by the National Natural Science Foundation of China (60171023)Biography: JI Xiao-bo (1980-), male, Master, research direction: electroanalytical chemistry.

Electrochemical Behavior and Its Electrocatalytic Activity of A P-Mo Heteropolyanion Modified ITO Electrode

s: A new method for the preparation of an organic-inorganic composite film of the heteropolyanion has been developed by modifying P(Mo2O7)6-7 to the indium tin oxide (ITO) electrode surface. The modified electrode displayed a strong catalytic activity towards the reduction of IO3-. In the range of 1.0?0-6~5?0-4mol/L, the catalytic current was linear proportional to the IO3- concentration.

Electrochemical Behavior of Eu^（3＋） on Eastman AQ－29D Chemically Modified Electrode

The electrochemical behaviors of Eu3+ on Eastman AQ-29D/glassy carbon(GC) chemically modified electrode(CME) were studied. It was found that the reduction-oxidation process of Eu3+ is in a semi-infinite condition in 0.1 mol/L NaCIO4 supporting electrolyte(pH 4.4). The calibration curve was linear over the range 1.0×10-7 to 1.0×105 mol/L of Eu3+.The charge transport apparent diffusion coefficient of Eu3+ in the polymer film was determined to be(3.2±1.1)×10-11cm2/s by chronocoulometry.

Cyclic Voltammetric Responses of Nitrate Reductase on Chemical Modified Electrodes

Electrochemistry of nitrate reductases (NR) incorporated into 2-aminoethanethiol self-assembled on the gold electrode and polyacrylamide cast on the pyrolytic graphite electrode was examined. NR on chemical modified electrode showed electrochemical cyclic voltammetric responses in phosphate buffers.

Removal of astrazon golden yellow 7GL from colored wastewater using chemically modified clay

Chemically modified clay(CMC) was used as an adsorbent for the removal of Astrazon Golden Yellow 7GL(AGY-7GL), which is a basic dye from wastewater. For this purpose, the chemically modified clay was first characterized by determining zero point of charge(p Hzpc), and using BET, SEM and FTIR. Then effects of operational parameters on adsorption of AGY-7GL were studied in a batch system. The effect of various parameters such as contact time(0-180 min), pH(2-8), temperature(293-323 K), CMC concentration(0.075-0.5 mg/L) and initial AGY-7GL concentration(75-250 mg/L) were investigated on the adsorption efficiency and capacity adsorption of CMC for the removal of AGY-7GL. Thermodynamic and kinetic parameters were calculated from the results of the adsorption experiment. The evaluation of kinetic models shows that this data best fits the pseudo-second-order model. It is determined that the adsorption equilibrium data works very well with the nonlinear Freundlich isotherm model. Thermodynamic parameters such as ?H^0(19.0 k J/mol), ?G^0(-28.8 k J/mol) and ?S^0(0.148 k J/mol) were also determined. According to the experimental results, it is concluded that CMC could be used as an alternative low cost potential adsorbent for the removal of AGY-7GL from wastewater.

Electrochemical Behaviour of Europium-Ferrocene Derivative Complex Chemi cally Modified Electrodes

Electrochemical behaviours of Europium-ferrocene derivative complex chemically modified electrodes were studied in the paper. Various factors which affect the voltammetry of the thin film modified electrodes, and the charge transport process of the thin film electrode were discussed. Size of the hydrated anion (counter ion), concentration of the electrolyte, swelling property of the film in the solvent and thickness of the film have significant effects on the voltammetry of the thin film electrode. Electrochemical behaviours of europium-ferrocene derivative compelx chemically modified electrode were studied in an aqueous solution. When scan ning between 0-0.8 V (vs. SCE), experimental results indicate that the chemically modified electrode has good stability and reproducibility. The apparent rate constant of electrode reaction is deteminedd to be 6.7×10-1 s-1.

A novel aminated polymeric adsorbent for removing refractory dissolved organic matter from landfill leachate treatment plant

Refractory dissolved organic matter （DOM） from landfill leachate treatment plant was with high dissolved organic carbon （DOC） content. An aminated polymeric adsorbent NDA-8 with tertiary amino groups and sufficient mesopore was synthesized, which exhibited high adsorption capacity to the DOM （raw water after coagulation）. Resin NDA-8 performed better in the uptake of the DOM than resin DAX-8 and A100. Electrostatic attraction was considered as the decisive interaction between the adsorbent and adsorbate. Special attention was paid to the correlation between porous structure and adsorption capacity. The mesopore of NDA-8 played a crucial role during uptake of the DOM. In general, resin in chloride form performed a higher removal rate of DOC. According to the colunm adsorption test, total adsorption capacity of NDA-8 was calculated to 52.28 mg DOC/mL wet resin. 0.2 mol/L sodium hydroxide solution could regenerate the adsorbent efficiently.

Electrocatalytic oxidation of methanol at platinum electrode modified with Eu-Fe cyanide-bridged binuclear complexes

The electrocatalytic oxidation of methanol at the platinum electrode modified with Eu-Fe cyanide-bridged binuclear complexes (Eu-Fe film) was investigated for the first time by cyclic voltammetry.Compared with the bare platinum electrode,the results showed that the modified electrode had excellent electrocatalytic activity for the oxidation of methanol;the oxidation peak potential shifted more negatively and the peak current increased about twenty times.The electrooxidation of methanol at the modified elect...

Determination of 6-Mercaptopurine in Rat Blood by Microdialysis Coupled with High Performance Liquid Chromatography on a Functionalized Multi-wall Carbon Nanotubes Modified Electrode

A new chemically modified electrode(CME) immobilized on the surface of multi-wall carbon nanotubes functionalized with carboxylic groups was fabricated. The results indicate that the CME exhibits efficiently electrocatalytic oxidation of 6-mercaptopurine(6-MP). The CME can be used as the working electrode in the liquid chromatography for the determination of 6-MP. The peak current of 6-MP is linearly changed with its concentration ranging from 4.0×10 -7 to 1.0×10 -4 mol/L with the calculated detection limit (S/N=3) of 2.0×10 -7 mol/L. Coupled with microdialysis sampling, the method has been successfully applied to assessing the content of 6-MP in rat blood.

Copper modified platinum electrode for amperometric detection of spectinomycin sulfate by anion-exchange chromatography

A La^3＋-Cu/Pt modified electrode was fabricated by electrodepositing process in CuS04 solution by adding a small amount of lanthium compound, and it was employed for direct current （DC） amperometric detection of spectinomycin by anion-exchange chromatography. Without derivatization, this method can simultaneously determine the main component and impurities in spectinomycin pharmaceutical raw material. Ease of preparation, being applied in DC detection mode and good catalytic stability confirmed the interests of this modified electrode as amperometric sensor for the determination of spectinomycin.