Grindability Evaluation of Ultrasonic Assisted Grinding of Silicon Nitride Ceramic Using Minimum Quantity Lubrication Based SiO_(2)Nanofluid

Minimum quantity Lubrication(MQL)is a sustainable lubrication system that is famous in many machining systems.It involve the spray of an infinitesimal amount of mist-like lubricants during machining processes.The MQL system is affirmed to exhibit an excellent machining performance,and it is highly economical.The nanofluids are understood to exhibit excellent lubricity and heat evacuation capability,compared to pure oil-based MQL system.Studies have shown that the surface quality and amount of energy expended in the grinding operations can be reduced considerably due to the positive effect of these nanofluids.This work presents an experimental study on the tribological performance of SiO_(2)nanofluid during grinding of Si_(3)N_(4)ceramic.The effect different grinding modes and lubrication systems during the grinding operation was also analyzed.Different concentrations of the SiO_(2)nanofluid was manufactured using canola,corn and sunflower oils.The quantitative evaluation of the grinding process was done based on the amount of grinding forces,specific grinding energy,frictional coefficient,and surface integrity.It was found that the canola oil exhibits optimal lubrication performance compared to corn oil,sunflower oil,and traditional lubrication systems.Additionally,the introduction of ultrasonic vibrations with the SiO_(2)nanofluid in MQL system was found to reduce the specific grinding energy,normal grinding forces,tangential grinding forces,and surface roughness by 65%,57%,65%,and 18%respectively.Finally,regression analysis was used to obtain an optimum parameter combinations.The observations from this work will aid the smooth transition towards ecofriendly and sustainable machining of engineering ceramics.

Damage evolution and removal behaviors of GaN crystals involved in double-grits grinding

Elucidating the complex interactions between the work material and abrasives during grinding of gallium nitride(GaN)single crystals is an active and challenging research area.In this study,molecular dynamics simulations were performed on double-grits interacted grinding of GaN crystals;and the grinding force,coefficient of friction,stress distribution,plastic damage behaviors,and abrasive damage were systematically investigated.The results demonstrated that the interacted distance in both radial and transverse directions achieved better grinding quality than that in only one direction.The grinding force,grinding induced stress,subsurface damage depth,and abrasive wear increase as the transverse interacted distance increases.However,there was no clear correlation between the interaction distance and the number of atoms in the phase transition and dislocation length.Appropriate interacted distances between abrasives can decrease grinding force,coefficient of friction,grinding induced stress,subsurface damage depth,and abrasive wear during the grinding process.The results of grinding tests combined with cross-sectional transmission electron micrographs validated the simulated damage results,i.e.amorphous atoms,high-pressure phase transition,dislocations,stacking faults,and lattice distortions.The results of this study will deepen our understanding of damage accumulation and material removal resulting from coupling between abrasives during grinding and can be used to develop a feasible approach to the wheel design of ordered abrasives.

Towards Sustainable Grinding of Difficult-to-Cut Alloys-A Holistic Review and Trends

Grinding,a critical precision machining process for difficult-to-cut alloys,has undergone continual technological advancements to improve machining efficiency.However,the sustainability of this process is gaining heightened attention due to significant challenges associated with the substantial specific grinding energy and the extensive heat generated when working with difficult-to-cut alloys,renowned for their exceptional physical and mechanical properties.In response to these challenges,the widespread application of massive coolant in manufacturing industries to dissipate grinding heat has led to complex post-cleaning and disposal processes.This,in turn,has resulted in issues such as large energy consumption,a considerable carbon footprint,and concerns related to worker health and safety,which have become the main factors that restrict the development of grinding technology.This paper provides a holistic review of sustainability in grinding difficult-to-cut alloys,encompassing current trends and future directions.The examination extends to developing grinding technologies explicitly tailored for these alloys,comprehensively evaluating their sustainability performance.Additionally,the exploration delves into innovative sustainable technologies,such as heat pipe/oscillating heat pipe grinding wheels,minimum quantity lubrication,cryogenic cooling,and others.These groundbreaking technologies aim to reduce dependence on hazardous coolants,minimizing energy and resource consumption and carbon emissions associated with coolant-related or subsequent disposal processes.The essence of these technologies lies in their potential to revolutionize traditional grinding practices,presenting environmentally friendly alternatives.Finally,future development trends and research directions are put forward to pursue the current limitation of sustainable grinding for difficult-to-cut alloys.This paper can guide future research and development efforts toward more environmentally friendly grinding operations by understanding the current state of sustainable grinding and identifying emerging trends.

Effects of Different Grinding Methods on the Quality of Soybean Bean Milk

[Objectives] This study was conducted to improve the nutritional value of soybean milk, enrich the variety and taste of soybean milk, and find healthy food that is more conducive to people s nutritional needs. [Methods] Whole soybean milk was prepared by grinding with a grinding wheel at a low concentration (low-concentration grinding) and a stainless steel mill at a high concentration (high-concentration grinding). The sensory, physical and chemical characteristics and anti-nutritional factors of whole soybean milk produced by different grinding methods were studied. [Results] Compared with low-concentration grinding, the protein content in soybean milk prepared by high-concentration grinding increased by 24%, and the dietary fiber content increased by 74.7%. Before and after high-pressure homogenization, the particle size D(4, 3) of soybean milk prepared by low-concentration grinding was 212.1 and 93.59 μm, respectively, and the particle size D(4, 3) of soybean milk prepared by high-concentration grinding was 134.0 and 64.64 μm, respectively. The trypsin inhibitor activity and phytic acid content of soybean milk prepared by high-concentration grinding were significantly lower than those of soybean milk prepared by low-concentration grinding. [Conclusions] This study improves the diet structure of the broad masses of people, strengthens people s physique, and provides a new idea for the implementation and development of China s "Soybean Action Programme".

Improving fatigue properties of normal direction ultrasonic vibration assisted face grinding Inconel 718 by regulating machined surface integrity

Fatigue properties are crucial for critical aero-engine components in extreme serviceenvironments,which are significantly affected by surface integrity(SI)indexes(especially surface topography,residual stressσ_(res),and microhardness)after machining processes.Normal-direction ultrasonic vibration-assisted face grinding(ND-UVAFG)has advantages in improving the machinability of Inconel 718,but there is a competitive relationship between higher compressiveσ_(res)and higher surface roughness R_(a)in affecting fatigue strength.The lack of a quantitative relationship between multiple SI indexes and fatigue strength makes theindeterminacy of a regulatory strategy for improving fatigue properties.In this work,a model of fatigue strength(σ_f)_(sur)considering multiple SI indexes was developed.Then,high-cycle fatigue tests were carried out on Inconel 718 samples with different SI characteristics,and the influence of ND-UVAFG process parameters on SI was analyzed.Based on SI indexes data,the(σ_f)_(sur)distribution in the grinding surface layer for ND-UVAFG Inconel 718 samples was determined using the developed model,and then the fatigue crack initiation(FCI)sites were furtherpredicted.The predicted FCI sites corresponded well with the experimental results,therebyverifying this model.A strategy for improving the fatigue life was proposed in this work,which was to transfer the fatigue source from the machined surface to the bulk material by controlling the SI indexes.Finally,a critical condition of SI indexes that FCI sites appeared on the surface or in bulk material was given by fitting the predicted results.According to the critical condition,an SI field where FCI sites appeared in the bulk material could be obtained.In this field,thefatigue life of Inconel 718 samples could be improved by approximately 140%.

Isolation and Characterization of Cellulose Nanofiber(CNF)from Kenaf(Hibiscus cannabinus)Bast through the Chemo-Mechanical Process

The present work emphasizes the isolation of cellulose nanofiber(CNF)from the kenaf(Hibiscus cannabinus)bast through a chemo-mechanical process.In order to develop high CNF yield with superior properties of CNF for improving compatibility in varied applications this method is proposed.The fiber purification involved pulping and bleaching treatments,whereas mechanical treatment was performed by grinding and high-pressure treatments.The kraft pulping as a delignification method followed by bleaching has successfully removed almost 99%lignin in the fiber with high pulp yield and delignification selectivity.The morphology of the fibers was characterized by scanning electron microscopy,which showed a smooth surface,fiber bundles,gel-shaped nanofiber,and an average size of 94.05 nm with 69%of CNF in 34–100 nm size.The chemo-mechanical process exhibited a more crystalline nature in CNF than pulp kenaf.The low zeta potential values exhibit the distribution of fibrils and colloidal suspension stability without any further agglomeration.A lower concentration of CNF is less stable exhibiting the product agglomeration.Therefore,the chemo-mechanical process for the isolation of CNF(Hibiscus cannabinus)from kenaf involves sustainable,low-cost,non-toxic,and cheap alternatives than other traditional methods.

High-performance grinding of ceramic matrix composites

Ceramic matrix composites(CMCs)are highly promising materials for the next generation of aero-engines.However,machining of CMCs suffers from low efficiency and poor surfacefinish,which presents an obstacle to their wider application.To overcome these problems,this study investigates high-efficiency deep grinding of CMCs,focusing on the effects of grinding depth.The results show that both the sur-face roughness and the depth of subsurface damage(SSD)are insensitive to grinding depth.The material removal rate can be increased sixfold by increasing the grinding depth,while the surface roughness and SSD depth increase by only about 10%.Moreover,it is found that the behavior of material removal is strongly dependent on grinding depth.As the grinding depth is increased,fibers are removed in smaller sizes,with thefiber length in chips being reduced by about 34%.However,too large a grinding depth will result in blockage by chip powder,which leads to a dramatic increase in the ratio of tangential to normal grinding forces.This study demonstrates that increasing the depth of cut is an effective approach to improve the machining efficiency of CMCs,while maintaining a good surfacefin-ish.It provides the basis for the further development of high-performance grinding methods for CMCs,which should facilitate their wider application.

Two-stage extraction by partial grinding of impacted mandibular third molar in close proximity to the inferior alveolar nerve

BACKGROUND Extraction of impacted third molars often leads to severe complications caused by damage to the inferior alveolar nerve(IAN).AIM To proposes a method for the partial grinding of an impacted mandibular third molar(IMM3)near the IAN to prevent IAN injury during IMM3 extraction.METHODS Between January 1996 and March 2022,25 patients with IMM3 roots near the IAN were enrolled.The first stage of the operation consisted of grinding a major part of the IMM3 crown with a high-speed turbine dental drill to achieve sufficient space between the mandibular second molar and IMM3.After 6 months,when the root tips were observed to be away from the IAN on X-ray examination,the remaining part of the IMM3 was completely removed.RESULTS All IMM3s were extracted easily without symptoms of IAN injury after extraction.CONCLUSION Partial IMM3 grinding may be a good alternative treatment option to avoid IAN injury in high-risk cases.

Microwave assisted grinding of ilmenite ore

The influence of microwave heating on the grinding of Panzhihua ilmenite ore was investigated. Factors that influence the processing are： the microwave exposure time, power density and sample mass. 40 g sample was microwave heated for 30 s with 1 kW of microwave power and followed by water quenching. SEM analysis indicated that intergranular fractures occurred between ores and gangues other than transgranular fractures after microwave treatment, which would liberate minerals from each other effectively. The subsequently magnetic separation trials provided evidence that the recovery rate increased from 44% for raw ore to 72% by microwave treatment.

PERFORMANCE OF BRAZED DIAMOND CUP-TYPE WHEELS WITH DEFINED GRAIN PATTERN IN GRINDING CEMENTED CARBIDE

A new cup-type grinding wheel of the brazed monolayer diamond is developed with a defined grain pattern on the wheel surface. Grinding performance of the brazed wheel in the surface grinding of cemented carbide is studied. Experimental results show that when continuous dry grinding is employed, grits of the brazed diamond grinding wheel fail mainly in attritious wear and fracture modes and no pull-out ones are found in conventional electroplated and sintered diamond wheels. It indicates the strong retention of brazing alloy to diamond grits and the longer service life of the wheel. In addition, the ground surface has good roughness. The theoretical surface roughness agrees well with experimental results.

GRINDING FORCE IN PRECISION MACHINING OF WC-Co COATING BY CUP WHEEL

High machining precision and machining efficiency can be obtained in grinding WC-Co coating by cup wheel. The conventional model of the grinding force is not suitable for the grinding of the cup wheel due to the difference in grinding style between the cup wheel and the conventional external wheel. So the grit grinding process of the cup wheel is studied, and a new concept of the effective grinding width of the cup wheel is presented. Then the grinding force in grinding WC-Co coating materials by cup wheel is analyzed and a theoretical formula is deduced. Finally, experimental results of the grinding force verify the correctness and the precision of the theoretical formula.

DRY GRINDING OF Ti6Al4V ALLOY WITH FLAP WHEELS

The grindability of alloy Ti6AI4V with zireonia alumina and silicon carbide flap wheels, and the effect of process parameters on grinding forces, grinding temperature and surface integrity are studied. The grinding forces are measured by KISTLER 9265B dynamometer. The grinding temperature response is obtained by NI USB-621X signal collection system. Ground surface morphology and the metallographic structure are observed by the Hirox KN-7700 stereoscopic microcope and the Quanta200 scanning electron microscope （SEM）. Surface roughnesses are measured by Mahr Perthometer M1 instrument. The surface microhardnesses are detected by HXS-1000 microhardness tester.

ELECTROCHEMICAL GRINDING OF UNPARALLEL-RULED SURFACE

To solve the problem of finishing the twist blade surface of an impeller, the five-axis numerically controlled electrochemical contour evolution grinding （NC-ECCEG） is studied. Over-cutting errors of NC-ECCEG of the twist blade surface generated by parallel lines are analyzed. The formula for calculating the over-cutting error is deduced. The method for eliminating the over-cutting error is used in the conical grinding wheel and the combined five-axis linkage NC-ECCEG system. The structure and the movement of the NC-ECCEG machine tool,the combined multi-axis NC system and its linkage control technology are introduced. Further, the mathematical model of the NC-ECCEG unparallel-ruled surface is established. An auto-programming system on five-axis NGECCEG is developed to grind the impeller. The machining efficiency of NC-ECCEG increases more than 12 times than that of manual polishing operations.

GRINDING TEMPERATURE AND COOLING RATE DURING GRIND-HARDENING OF 40Cr STEEL

The mathematical model of the grinding temperature is established. The grinding temperature and the cooling rate are measured in the grind-hardening process of 40Cr steel under different conditions. Moreover, the grind-hardening effects are investigated. Experimental results show that the calculated temperatures are comparatively close to the measured ones, and the required temperature and cooling rate can be achieved. Furthermore, the microstructure of the hardened zone is similar to that obtained through the high-frequency induction technique. The average hardness of the entirely hardened zone is HV670 and the thickness of the hardened layer is adjacent to 1.3 mm. It indicates that the hardening mechanism induced by the grinding heat and high-frequency heating is identical. Finally, the fine needlelike martensite is obtained.

Cement Grinding System Status of Roller Press

The working principle of cement roller press and current development of wear resistance on the cement grinding system status at home and abroad was described. The main improvement of previous research on the wear resistance of roller press was proposed from three aspects of wear-resistant material, roller press roller structure, and surface morphology.

EXPERIMENTAL RESEARCH ON SLOTTED & PERFORATED ELECTROPLATED CBN GRINDING WHEEL WITH RADIAL JET

A creative conception is proposed to enhance heat transfer in grinding contact zone through jet impinging on the basis of analysis on the mechanism of burn during creep feed grinding, and a new apparatus of slotted & perforated electroplated CBN grinding wheel with radial jet is developed, the effect on heat transfer is studied through the experiment of intermitted creep feed grinding. Experimental results show that the technology of enhancing heat transfer through jet impinging is valid to raise the efficiency of heat transfer in grinding contact zone and it is widely applied to solve the problem in grinding burn for difficult to machine materials.

Subsurface Damage in the Monocrystal Silicon Grinding on Atomic Scale

A molecular dynamics （MD） simulation is carried out to analyze the effect of cutting edge radius,cutdepth, and grinding speed on the depth of subsurface damage layers in monocrystal silicon grinding processes on an atomic scale. The results show that when the cutting edge radius decreases in the nanometric grinding process with the same cut-depth and grinding speed, the depth of the damage layers and the potential energy between the silicon atoms decrease too. Also, when the cut depth increases, both the depth of the damage layers and the potential energy between silicon atoms increase. When the grinding speed is between 20 and 200m/s,the depth of the damage layers does not change much with the increase of the grinding speed under the same cutting edge radius and cut depth conditions. This means that the MD simulation is not sensitive to changes in the grinding speed, and thus increasing the grinding speed properly can shorten the sion,the subsurface damage of monocrystal silicon is silicon atoms, which is verified by the ultra-precision simulation time and enlarge the simulation scale. In conclumainly based on the change of the potential energy between grinding and CMP experiments.

THERMAL STUDY ON THE GRINDING OF GRANITE WITH SUPERABRASIVE TOOLS

In the present paer, a thermal study was conducted for the grinding of granite with diamond tools. Three types of grinding-straight surface grinding, deep grinding(circular sawing), and vertical spindle grinding-were studied. Some surface grinding tests were also conducted using a CBN(cubic boron nitride) wheel. Temperature distributions on the workpiece surface were measured using a foil thermocouple and the energy partition to the workpiece was estimated using a temperature matching method. The temperature for CBN surface grinding was found to be much higher than for diamond grinding. Energy partitions to the granite were 30%～36% for CBN surface grinding, 25%～32% for diamond surface grinding, about 53% for vertical spindle grinding, and 5.5%～9% for diamond deep grinding. The low energy partition value in deep grinding also suggested that more of the heat generated by grinding in this case can be conducted to the grinding tool and promote tool wear.

On-Line Monitoring of Grinding Status Based on Rough Set Theory

This paper focuses on the new approach of on line monitoring of grinding burn and wheel wear based on the rough set theory. This method adopts the grinding chip flow thermal signal, and acquires identification rules by establishing sensitive characteristic parameters and constructing the knowledge system through continuum attribute discretization, attribute reduction and knowledge acquisition, and then monitors grinding burn and wheel wear in accordance with the acquired rules. The experiment results show that the new method is effective.

SUPPORT SYSTEM FOR FREE SURFACE GRINDING BASED ON PATCH DIVISION

To obtain accurate forms and surfaces in free surface grinding, it is important to provide grinding conditions suitable for a curved surface. A grinding support system for the free surface （GSX-F） is proposed to help the operator grind a free surface with the high accuracy and the high productivity. To succeed in free surface grinding, the property of a ball type wheel must be known. Therefore, a basic study of free surface grinding with a ball type wheel is carried out based on the grinding center （GC）. Some working points for achieving sufficient accuracy in free surface grinding are discussed. GSX-F is constructed using the patch division method and is used to test grinding. Reasonable results are obtained.