Effects of Chlorine and Chlorine Monoxide on Stratospheric Ozone Depletion

This paper presents a system approach of mass balance calculations of ozone and other species under diffusion-convection-reaction processes to study the impacts of major ozone-depleting chemicals, chlorine (Cl) and chlorine monoxide (ClO), and the effect of photolysis on ozone concentrations, ozone depletion, total ozone abundance, and ozone layer along the altitude in the stratosphere. The calculated ozone concentrations and profile of the layer followed a similar trend and were generally in good agreement with the measurements above the tropical area. The calculated peak of the layer was at the same mid-stratosphere at Z = 30 km with a peak concentration and total ozone abundance about 20% higher than the measured peak concentration of 8.0 ppm and total abundance of 399 DU. In the presence of Cl and ClO, the calculated ozone concentrations and total abundance were substantially reduced. Cl generally depleted more uniformly of ozone across the altitude, while ClO reduced substantially the ozone in the upper stratosphere and thus shifted the peak of the layer to a much lower elevation at Z = 14 km. Although both ClO and Cl are active ozone-depleting chemicals, ClO was found to have a more pronounced impact on ozone depletion and distribution than Cl. The possible explanations of these interesting phenomena were discussed and elaborated. The approach and calculations in this paper were shown to be useful in providing an initial insight into the structure and behavior of the complex ozone layer.

Unveiling the geometric site dependent activity of spinel Co_(3)O_(4)for electrocatalytic chlorine evolution reaction

Spinel cobalt oxide(Co_(3)O_(4)),consisting of tetrahedral Co^(2+)(CoTd)and octahedral Co^(3+)(CoOh),is considered as promising earth-abundant electrocatalyst for chlorine evolution reaction(CER).Identifying the catalytic contribution of geometric Co site in the electrocatalytic CER plays a pivotal role to precisely modulate electronic configuration of active Co sites to boost CER.Herein,combining density functional theory calculations and experiment results assisted with operando analysis,we found that the Co_(Oh) site acts as the main active site for CER in spinel Co_(3)O_(4),which shows better Cl^(-)adsorption and more moderate intermediate adsorption toward CER than CoTd site,and does not undergo redox transition under CER condition at applied potentials.Guided by above findings,the oxygen vacancies were further introduced into the Co_(3)O_(4) to precisely manipulate the electronic configuration of Co_(Oh) to boost Cl^(-)adsorption and optimize the reaction path of CER and thus to enhance the intrinsic CER activity significantly.Our work figures out the importance of geometric configuration dependent CER activity,shedding light on the rational design of advanced electrocatalysts from geometric configuration optimization at the atomic level.

One-Step Scalable Fabrication of Nitrogen and Chlorine Co-doped Graphene by Electrochemical Exfoliation for High-Performance Supercapacitors

The stacking and aggregation of graphene nanosheets have been obstacles to their application as electrode materials for microelectronic devices.This study deploys a one-step,scalable,facile electrochemical exfoliation technique to fabricate nitrogen(N)and chlorine(Cl)co-doped graphene nanosheets(i.e.,N-Cl-G)via the application of constant voltage on graphite in a mixture of 0.1 mol/L H_(2)SO_(4)and 0.1 mol/L NH_(4)Cl without using dangerous and exhaustive operation.The introduction of Cl(with its large radius)and N,both with high electrical negativity,facilitates the modulation of the electronic structure of graphene and creation of rich structural defects in it.Consequently,in the as-constructed supercapacitors,N-Cl-G exhibits a high specific capacitance of 77 F/g at 0.2 A/g and remarkable cycling stability with 91.7%retention of initial capacitance after 20,000 cycles at 10 A/g.Furthermore,a symmetrical supercapacitor assembled with N-Cl-G as the positive and negative electrodes(denoted as N-Cl-G//N-Cl-G)exhibits an energy density of 3.38 Wh/kg at a power density of 600 W/kg and superior cycling stability with almost no capacitance loss after 5000 cycles at 5 A/g.This study provides a scalable protocol for the facile fabrication of high-performance co-doped graphene as an electrode material candidate for supercapacitors.

Detection of Oxidants Such as Hydroxyl Radicals and Chlorine Electrogenerated on a BDD Electrode by Simple Methods

The aim of this work is to detect electrogenerated hydroxyl radicals and chlorine by simple and less expensive methods. Preparative electrolyses of perchloric acid (HClO4) and sodium chloride (NaCl) were performed on a boron-doped diamond (BDD) electrode. The hydroxyl radicals were quantified indirectly by assaying the samples from the HClO4 (0.1 M) electrolysis with a 10−4 M potassium permanganate solution. The investigations showed that the amount of hydroxyl radicals depends on the concentration of HClO4 and the current density. As for chlorine, a qualitative determination was carried out. A mixture of the electrolyte solution of HClO4 (0.1 M) + NaI (0.2 M) + 2 mL of hexane, taken in this order, leads to a purplish-pink coloration attesting to the presence of Cl2. The same test was carried out with NaBr and NaI giving pale and very pale pink colourations, respectively, showing that the intensity of the colouration depends on the strength of the oxidant present. In addition, oxidants were detected during the electrooxidation of metronidazole (MNZ). The results showed the participation of electrogenerated hydroxyl radicals. The generation of chlorine has also been proven. Furthermore, the degradation leads to a chemical oxygen demand (COD) removal rate of 83.48% and the process is diffusion-controlled.

Chlorine-Substituent Regulation in Dopant-Free Small-Molecule Hole-Transport Materials Improves the Effi ciency and Stability of Inverted Perovskite Solar Cells

Although doped hole-transport materials(HTMs)off er an effi ciency benefi t for perovskite solar cells(PSCs),they inevi-tably diminish the stability.Here,we describe the use of various chlorinated small molecules,specifi cally fl uorenone-triphenylamine(FO-TPA)-x-Cl[x=para,meta,and ortho(p,m,and o)],with diff erent chlorine-substituent positions,as dopant-free HTMs for PSCs.These chlorinated molecules feature a symmetrical donor-acceptor-donor structure and ideal intramolecular charge transfer properties,allowing for self-doping and the establishment of built-in potentials for improving charge extraction.Highly effi cient hole-transfer interfaces are constructed between perovskites and these HTMs by strategi-cally modifying the chlorine substitution.Thus,the chlorinated HTM-derived inverted PSCs exhibited superior effi ciencies and air stabilities.Importantly,the dopant-free HTM FO-TPA-o-Cl not only attains a power conversion effi ciency of 20.82% but also demonstrates exceptional stability,retaining 93.8%of its initial effi ciency even after a 30-day aging test conducted under ambient air conditions in PSCs without encapsulation.These fi ndings underscore the critical role of chlorine-substituent regulation in HTMs in ensuring the formation and maintenance of effi cient and stable PSCs.

Effects of surface chlorine atoms on charge distribution and reaction barriers for photocatalytic CO_(2)reduction

Photocatalytic CO_(2)reduction to produce high value-added carbon-based fuel has been proposed as a promising approach to mitigate global warming issues.However,the conversion efficiency and product selectivity are still low due to the sluggish dynamics of transfer processes involved in proton-assisted multi-electron reactions.Lowering the formation energy barriers of intermediate products is an effective method to enhance the selectivity and productivity of final products.In this study,we aim to regulate the surface electronic structure of Bi_(2)WO_(6)by doping surface chlorine atoms to achieve effective photocatalytic CO_(2)reduction.Surface Cl atoms can enhance the absorption ability of light,affect its energy band structure and promote charge separation.Combined with DFT calculations,it is revealed that surface Cl atoms can not only change the surface charge distribution which affects the competitive adsorption of H_(2)O and CO_(2),but also lower the formation energy barrier of intermediate products to generate more intermediate*COOH,thus facilitating CO production.Overall,this study demonstrates a promising surface halogenation strategy to enhance the photocatalytic CO_(2)reduction activity of a layered structure Bi-based catalyst.

Calculations and Sensitivity Analysis of Chlorine-,NO_(x)-,and Bromine-Depleting Cycles of Stratospheric Ozone

This paper presents an engineering system approach using a 2D model of conservation of mass to study the dynamics of ozone and concerned chemical species in the stratosphere.By considering all fourteen photolysis,ozone-generating,and-depleting chemical reactions,the model calculated the transient,spatial changes of ozone under different physical-chemical-radiative conditions.Validation against the measured data demonstrated good accuracy,close match of our model with the observed ozone concentrations at both 20°S and 90°N locations.The deviation in the average concentration was less than 1% and in ozone profiles less than 17%.The impacts of various chlorine-(Cl),nitrogen oxides-(NO_(x)),and bromine-(Br)depleting cycles on ozone concentrations and distribution were investigated.The chlorine catalytic depleting cycle was found to exhibit the most significant impact on ozone dynamics,confirming the key role of chlorine in the problem of ozone depletion.Sensitivity analysis was conducted with levels of 25%,50%,100%,200%,and 400% of the baseline value.The combined cycles(Cl+NO_(x)+Br)showed the most significant influence on ozone behavior.The total ozone abundance above the South Pole could decrease by a small 3%,from 281 DU(Dubson Units)to 273 DU for the 25% level,or by a huge thinning of 60%to 114 DU for the 400% concentration level.When the level of chlorine gases increased beyond 200%,it would cause ozone depletion to a level of ozone hole(below 220 DU).The 2D Ozone Model presented in this paper demonstrates robustness,convenience,efficiency,and executability for analyzing complex ozone phenomena in the stratosphere.

Low-temperature chlorination roasting technology for the simultaneous recovery of valuable metals from spent LiCoO_(2)cathode material

With the continuous increase in the disposal volume of spent lithium-ion batteries(LIBs),properly recycling spent LIBs has become essential for the advancement of the circular economy.This study presents a systematic analysis of the chlorination roasting kinetics and proposes a new two-step chlorination roasting process that integrates thermodynamics for the recycling of LIB cathode materials.The activation energy for the chloride reaction was 88.41 kJ/mol according to thermogravimetric analysis–derivative thermogravimetry data obtained by using model-free,model-fitting,and Z(α)function(αis conversion rate).Results indicated that the reaction was dominated by the first-order(F1)model when the conversion rate was less than or equal to 0.5 and shifted to the second-order(F2)model when the conversion rate exceeded 0.5.Optimal conditions were determined by thoroughly investigating the effects of roasting temperature,roasting time,and the mass ratio of NH_(4)Cl to LiCoO_(2).Under the optimal conditions,namely 400℃,20 min,and NH_(4)Cl/LiCoO_(2)mass ratio of 3:1,the leaching efficiency of Li and Co reached 99.43% and 99.05%,respectively.Analysis of the roasted products revealed that valuable metals in LiCoO_(2)transformed into CoCl_(2) and LiCl.Furthermore,the reaction mechanism was elucidated,providing insights for the establishment of a novel low-temperature chlorination roasting technology based on a crystal structure perspective.This technology can guide the development of LIB recycling processes with low energy consumption,low secondary pollution,high recovery efficiency,and high added value.

Health Risk Assessment of Employees Exposed to Chlorination By-products of Recreational Water in Large Amusement Parks in Shanghai

Objective Chlorination is often used to disinfect recreational water in large amusement parks;however,the health hazards of chlorination disinfection by-products(DBPs)to occupational populations are unknown.This study aimed to assess the exposure status of chlorinated DBPs in recreational water and the health risks to employees of large amusement parks.Methods Exposure parameters of employees of three large amusement parks in Shanghai were investigated using a questionnaire.Seven typical chlorinated DBPs in recreational water and spray samples were quantified by gas chromatography,and the health risks to amusement park employees exposed to chlorinated DBPs were evaluated according to the WHO's risk assessment framework.Results Trichloroacetic acid,dibromochloromethane,bromodichloromethane,and dichloroacetic acid were detected predominantly in recreational water.The carcinogenic and non-carcinogenic risks of the five DBPs did not exceed the risk thresholds.In addition,the carcinogenic and non-carcinogenic risks of mixed exposure to DBPs were within the acceptable risk limits.Conclusion Typical DBPs were widely detected in recreational water collected from three large amusement parks in Shanghai;however,the health risks of DBPs and their mixtures were within acceptable limits.

Molecular packing tuning via chlorinated end group enables efficient binary organic solar cells over 18.5%

Designing novel nonfullerene acceptors(NFAs)is of vital importance for the development of organic solar cells(OSC).Modification on the side chain and end group are two powerful tools to construct efficient NFAs.Here,based on the high-performance L8BO,we selected 3-ethylheptyl to substitute the inner chain of 2-ethylhexyl,obtaining the backbone of BON3.Then we introduced different halogen atoms of fluorine and chlorine on 2-(3-oxo-2,3-dihydro-1Hinden-1-ylidene)malononitrile end group(EG)to construct efficient NFAs named BON3-F and BON3-Cl,respectively.Polymer donor D18 was chosen to combine with two novel NFAs to construct OSC devices.Impressively,D18:BON3-Cl-based device shows a remarkable power conversion efficiency(PCE)of 18.57%,with a high open-circuit voltage(V_(OC))of 0.907 V and an excellent fill factor(FF)of 80.44%,which is one of the highest binary PCE of devices based on D18 as the donor.However,BON3-F-based device shows a relatively lower PCE of 17.79%with a decreased FF of 79.05%.The better photovoltaic performance is mainly attributed to the red-shifted absorption,higher electron and hole mobilities,reduced charge recombination,and enhanced molecular packing in the D18:BON3-Cl films.Also,we performed stability tests on two binary systems;the D18:BON3-Cl and D18:BON3-F devices maintain 88.1%and 85.5%of their initial efficiencies after 169 h of storage at 85°C in an N2-filled glove box,respectively.Our work demonstrates the importance of selecting halogen atoms on EG and provides an efficient binary system of D18:BON3-Cl for further improvement of PCE.

The Toxic Effects of Strong Chlorin Disinfectant on Mangroves and Emission Thresholds

In this study, based on the simulated discharge results of chemical disinfectants, hypocotyl germination concentration gradient pre-test and concentration gradient determination experiment were set up respectively. Laboratory cultivation was conducted to compare and analyze the root germination and germination indexes, three mangrove hypocotyls of Kandelia candel (Linn.) Druce, Ceriopstagal C.B. Rob. and Bruguiera sexangula var. Rhynchopetalas’ efficiency of cumulative root germination, cumulative germination and the cumulative expansion of the second pair of leaves, one-way analysis of variance was used to obtain the tolerance threshold of three mangrove hypocotyls to strong chlorin disinfectant. The study determined that the by-products of strong chlorin disinfectant, the toxic threshold concentrations of Kandelia candel (Linn.) Druce, Ceriopstagal C.B. Rob. and Bruguiera sexangula var. rhynchopetala are close to 0.55 mg/L, 0.55 mg/L and 0.25 mg/L, respectively. This concentration range is lower than the average concentration of 1.183 mg/L of active chlorine emitted from strong chlorine concentrate during pond clearing in high-level shrimp ponds, indicating that transient emissions of strong chlorine concentrate during pond clearing can have a toxic effect on mangrove plants. The strength of tolerance of the embryonic axes of the three mangrove species to effective chlorine contamination was, Ceriopstagal C.B. Rob. stronger than Bruguiera sexangula var. rhynchopetala, and Kandelia candel (Linn.) Druce is the weakest.

Determination of Chlorine and Bromine in Plant Materials by Ion Chromatography

A method was developed for determination of chlorine and bromine in plant materials by ion chromatography using temperature programing-semi molten for sample preparation. Values of detection limits of the method found were 1.0×10^-5 for CI and 1.3×10^-6 for Br. The measuring range of the method found were 0.3-20.0 mg/L for CI and 4,0-120,0 μg/L for Br. The results obtained agreed quite well with those reference values.

Full-scale study of removal effect on Cyclops of zooplankton with chlorine dioxide

Cyclops of zooplankton propagated excessively in eutrophic water body and could not be effectively inactivated by the conventional disinfections process like chlorination due to its stronger resistance to oxidation. In this paper, a full-scale study of chlorine dioxide preoxidation cooperating with routine clarification process for Cyclops removal was conducted in a waterworks. The experimental results were compared with that of the existing prechlorination process in several aspects: including the Cyclops removal efficiencies of water samples taken from the outlets of sedimentation tank and sand filter and the security of drinking water and so on. The results showed that chlorine dioxide might be more effective to inactivate Cyclops than chlorine and Cyclops could be thoroughly removed from water by pre-dosing chlorine dioxide process. The GC-MS examination and Ames test further showed that the sort and amount of organic substance in the treated water by chlorine dioxide preoxidation were evidently less than that of prechlorination and the mutagenicity of drinking water treated by pre-dosing chlorine dioxide was substantially reduced compared with prechlorination.

Investigation of heavy metal partitioning influenced by flue gas moisture and chlorine content during waste incineration

The impact of moisture on the partitioning of the heavy metals including Pb,Zn,Cu and Cd in municipal solid waste （MSW） was studied in a laboratory tubular furnace.A thermodynamic investigation using CHEMKIN software was performed to compare the experimental results.Simulated waste,representative of typical MSW with and without chlorine compounds,was burned at the background temperature of 700 and 950°C,respectively.In the absence of chlorine,the moisture content has no evident effect on the volatility of Pb,Zn and Cu at either 700 or 950°C,however,as flue gas moisture increasing the Cd distribution in the bottom ash increased at 700°C and reduced at 950°C,respectively.In the presence of chlorine,the flue gas moisture reduced the volatility of Pb,Zn and Cu due to the transformation of the more volatile metal chlorides into less volatile metal oxides,and the reduction became significant as chlorine content increase.For Cd,the chlorine promotes its volatility through the formation of more volatile CdCl 2.As a result,the increased moisture content increases the Pb,Zn,Cu and Cd concentrations in the bottom ash,which limits the utilization of the bottom ash as a construction material.Therefore,in order to accumulate heavy metals into the fly ash,MSW should be dried before incineration.

VARIATIONS IN ISOTOPIC COMPOSITIONS OF CHLORINE IN EVAPORATION-CONTROLLED SALT LAKE BRINES OF QAIDAM BASIN,CHINA

The variations in the isotopic compositions of chlorine in evaporation controlled saline lake brines were determined by using an improved procedure for precise measurement of chlorine isotopes based on Cs 2Cl + ion by thermal ionization mass spectrometry. The results showed that variation in δ 37 Cl values in these evaporation controlled brines are attributable to evaporation of brine accompanied by the deposition of saline minerals. The isotopic fractionation of chlorine between the deposited saline mineral and the co existing brine caused the variation of δ 37 Cl values in the brine. In general the isotopic fractionation of chlorine in nature indicates enrichment of 3 7Cl in the solid phase relative to 3 5Cl. The reverse isotopic fractionation of chlorine in which 3 5Cl is enriched in the solid phase, was observed to some extent during quick deposition under laboratory conditions as well as in nature. The mechanism of isotopic fractionation of chlorine during evaporation deposition was studied.

Roasting and chlorine leaching of gold-bearing refractory concentrate:Experimental and process analysis

This paper deals with gold extraction from a refractory concentrate by chlorine leaching.The process considers a pre-treatment of refractory materials by low temperature oxidation carried out with low oxygen concentration.The oxidized material is treated by leaching with brine.After gold adsorption/reduction onto activated carbon,iron and base metals can be precipitated by NaOH.Roasting tests show the necessity to carry out a thermal pre-treatment at least at 550°C to obtain a reduction of sulfur and mercury in the material(50%and 90%,respectively).Highest gold extraction yield(around 93%)is obtained in the leaching test performed with material sample treated at 650°C.This result confrms the necessity to optimize the thermal pre-treatment to improve Au recovery and to reduce chlorine consumption.A comparison with conventional cyanidation confrms that chlorination could be an useful alternative:in fact,gold extraction yield is quite low:57%in non-pre-treated material and 25%in pre-treatment material.

Preparation and Evaluation of Novel Solid Chlorine Dioxide-based Disinfectant Powder in Single-pack

Objective To prepare and evaluate novel chlorine dioxide-based disinfectant powder in single-pack that is more convenient for use and transportation. Methods Orthogonal experiment was performed to determine the recipe of the disinfectant powder. Stability test, suspension quantitative bactericidal test, simulation field triM, and animal toxicity test were carded out to observe its bactericidal and toxicological effects. Results The orthogonal experiment showed that the type of water solution had no effect on the disinfectant powder and the best ratio of sodium chlorite to solid acid was 1：3. Ten grams of the disinfectant powder was fully dissolved in 20 mL water for 2 min, and diluted to 500 mL in water. After 5-10 min, the concentration of chlorine dioxide （CIO2） solution was 266 mg/L to 276 mg/L. After stored at 54℃ for 14 d, the average concentration of CIO2 was decreased by 5.03%. Suspension quantitative bactericidal test showed that the average killing logarithm （KL） value for both Staphylococcus aureus and Escherichia coli in 100 mg/L CIO2 solution for 2 min was over 5.00. In simulation field triM, the average descending KL value for Escherichia coli in the solution containing 100 mg/L CIO2 for 5 min was over 3.00. The mouse acute LD50 in the solution 5 times exceeded 5000 mg/kg. The disinfectant powder was not toxic and irritative to rabbit skin and had no mutagenic effect on mouse marrow polychromatic erythrocytes （PCE）. Conclusion The stability and bactericidal efficacy of solid chlorine dioxide-based disinfectant powder in single-pack are good. The solution containing 100 mg/L CIO2 can kill vegetative forms of bacteria. The concentration of CIO2 on the disinfecting surface of objects is 100 mg/L. The disinfectant powder is not toxic and irritative.

Effects of inorganic chlorine source on dioxin formation using fly ash from a fluidized bed incinerator

Chlorine source is indispensable for polychlorinated dibenzo-p-dioxin and furan （PCDD/F） formation during municipal solid waste （MSW） incineration. Inorganic chlorine compounds were employed in this study to investigate their effects on PCDD/F formation through heterogeneous synthesis on fly ash surfaces. A fly ash sample obtained from a fluidized bed incinerator was sieved to different size fractions which served as the PCDD/F formation sources. The capability of different metal chlorides which facilitate the formation of PCDDs/Fs was found to follow the trends： Na 〈 Mg 〈 K 〈 AI 〈 Ca, when two particle fractions of 〉177 μm and 104-125 μm were used in the experiments. However, the capability of NaCI, MgCl2 and KCI did not seem much different from each other, whereas CaCl2 and AlCl3 were much more active in PCDD/F formation. NaCl and MgCl2 were relatively effective to produce more PCDDs, while KC1, AICl3 and CaCl2 generated more PCDFs during heterogeneous reactions occurring on fly ash. 2,3,7,8-TCDF was the most significant contributor to the toxicity of the PCDDs/Fs formed from inorganic chlorine sources. Decreasing the sizes of fly ash particles led to more active formation of PCDDs/Fs when NaCl was used as inorganic chlorine in the experiment. The highest PCDDs/Fs produced from particles with size 〈37 μm, while the lowest PCDDs/Fs produced from particles with size 〉177μm. The toxicity generally increased with decreasing size of the fly ash particles. The formation of PCDDs was mainly facilitated by the two size fractions, 104-125 μm and 〈37μm, while the formation of PCDFs was favored by the two other size fractions, 〉177 μm and 53-104 μm.

Kinetics of aniline oxidation with chlorine dioxide

For the first time, kinetics of aniline oxidation with chlorine dioxide(ClO 2) were investigated systematically by detecting concentration of aniline with HPLC at regular intervals. Results showed that the reaction was first-order both in ClO 2 and in aniline, and the oxidation reaction could be described as second-order reaction. Stoichiometric factor η was experimentally determined to be 2 44. The second-order-reaction rate constant k was 0 11 L/(mol·s) under condition of pH 6 86 and water temperature(T w) 287K. Reaction activation energy was 72 31 kJ/mol, indicating that the reaction could take place under usual water treatment conditions. The reaction rate constants in acidic and alkali media were greater than that in neutral medium. Chlorite ion could slightly increase reaction rate in acidic medium. p-aminophenol and azobenzene were detected by GC-MS as intermediates.

Pilot-scale study of removal effect on Chironomid larvae with chlorine dioxide

Chironomid larvae propagated excessively in eutrophic water body and could not be effectively inactivated by the conventional disinfection process like chlorination due to its stronger resistance to oxidation. In this paper, a pilot-scale study of chlorine dioxide preoxidation cooperating with routine clarification process for Chironomid larvae removal was conducted in Shenzhen Waterworks in Guangdong Province, China. The experimental results were compared with that of the existing prechlorination process in several aspects, including the Chironomid larvae removal efficiencies of water samples taken from the outlets of sedimentation tank, sand filter, the security of drinking water and so on. The results showed that chlorine dioxide might be more effective to inactivate Chironomid larvae than chlorine and Chironomid larvae could be thoroughly removed from water by pre-dosing chlorine dioxide process. The GC-MS examination and Ames test further showed that the sort and amount of organic substance in the treated water by chlorine dioxide preoxidation were evidently less than that ofprechlorination and the mutagenicity of drinking water treated by pre-dosing chlorine dioxide was substantially reduced compared with prechlorination.