The use of a glass-fiber reinforced composite in marine structures is becoming more common, particularly due to the potential weight savings. The mechanical response of the joint between a glass-fiber reinforced polym...The use of a glass-fiber reinforced composite in marine structures is becoming more common, particularly due to the potential weight savings. The mechanical response of the joint between a glass-fiber reinforced polymer （GRP） superstructure and a steel hull formed is examined and subsequently modified to improve performance through a combined program of modeling and testing. A finite-element model is developed to predict the response of the joint. The model takes into account the contact at the interface between different materials, progressive damage, large deformation theory, and a non-linear stress-strain relationship. To predict the progressive failure, the analysis combines Hashin failure criteria and maximum stress failure criteria. The results show stress response has a great influence on the strength and bearing of the joint. The Balsawood-steel interface is proved to be critical to the mechanical behavior of the joint. Good agreement between experimental results and numerical predictions is observed.展开更多
The effects of Ethylene-Vinyl Acetate copolymer （EVA） latex as an additive or a glass fiber surface modifier on the properties of Glass-Fiber （ GF ）/ Magnesium Oxychloride Cement （MOC） composites was studied. Th...The effects of Ethylene-Vinyl Acetate copolymer （EVA） latex as an additive or a glass fiber surface modifier on the properties of Glass-Fiber （ GF ）/ Magnesium Oxychloride Cement （MOC） composites was studied. The mechanical properties, water resistance aud aging resistance of the cured GF/ MOC composites were estimated and chemical ingredients analysis and morphological study of the GF/ MOC composites were also performed. It is found that EVA added to the MOC matrix could substantially improve the interfacial adhesion, water resistance aud aging resistance of GF/ MOC composites. EVA treatment on glass fibers resulted in decreasing initial flexural strength of GF/ MOC composites while enhancing the soft coefficients. In addition, the drying time and dilution of the EVA treatment on glass fibers also had an otwioas effect on the properties of GF/ MOC composites. However, excessive EVA interfered with the growth of the 5 Mg（ OH）2· MgCl2 ·8H2O crystal and the properties of GF / MOC composites.展开更多
The easiest and most reliable joining method is the mechanical joint with a bolt and nut or rivet. However, in the case of composite laminates, mechanical joint properties decrease because of lower interlaminar proper...The easiest and most reliable joining method is the mechanical joint with a bolt and nut or rivet. However, in the case of composite laminates, mechanical joint properties decrease because of lower interlaminar properties compared to in-plane properties around hole.?This study investigated needle punching process with the aim of improving the mechanical properties in the thickness direction of fiber-reinforced plastic composite laminates with an open hole. Needle punching process was applied to glass fiber chopped strand matused as the reinforcement for the composite laminates. Open-hole tensile tests and observations of end cross-sections after the tests were performed. The tensile properties and fracture mechanism of the specimens subjected to needle punching process were investigated. In addition, characteristic distance (a parameter for evaluating resistance to fracture in open-hole tensile test specimens) was also calculated to examine the effects of needle punching process conditions on fracture toughness. Tensile strength was improved by more than 15% by needle punching process. However, when a certain needle punching density was exceeded, the mechanical properties worsened. In addition, characteristic distance increased with increasing needle punching density. Thus, these results suggest that there is an optimal needle punching density with respect to strength and characteristic distance.展开更多
基金Foundation item： Supported by the National Natural Science Foundation of China （Grant No 61004008）, the Central Universities under Grant HEUCFR1001 and LBH-10138 Higher Sliding Mode Control for Underactuated Surface Ship.
文摘The use of a glass-fiber reinforced composite in marine structures is becoming more common, particularly due to the potential weight savings. The mechanical response of the joint between a glass-fiber reinforced polymer （GRP） superstructure and a steel hull formed is examined and subsequently modified to improve performance through a combined program of modeling and testing. A finite-element model is developed to predict the response of the joint. The model takes into account the contact at the interface between different materials, progressive damage, large deformation theory, and a non-linear stress-strain relationship. To predict the progressive failure, the analysis combines Hashin failure criteria and maximum stress failure criteria. The results show stress response has a great influence on the strength and bearing of the joint. The Balsawood-steel interface is proved to be critical to the mechanical behavior of the joint. Good agreement between experimental results and numerical predictions is observed.
文摘The effects of Ethylene-Vinyl Acetate copolymer （EVA） latex as an additive or a glass fiber surface modifier on the properties of Glass-Fiber （ GF ）/ Magnesium Oxychloride Cement （MOC） composites was studied. The mechanical properties, water resistance aud aging resistance of the cured GF/ MOC composites were estimated and chemical ingredients analysis and morphological study of the GF/ MOC composites were also performed. It is found that EVA added to the MOC matrix could substantially improve the interfacial adhesion, water resistance aud aging resistance of GF/ MOC composites. EVA treatment on glass fibers resulted in decreasing initial flexural strength of GF/ MOC composites while enhancing the soft coefficients. In addition, the drying time and dilution of the EVA treatment on glass fibers also had an otwioas effect on the properties of GF/ MOC composites. However, excessive EVA interfered with the growth of the 5 Mg（ OH）2· MgCl2 ·8H2O crystal and the properties of GF / MOC composites.
文摘The easiest and most reliable joining method is the mechanical joint with a bolt and nut or rivet. However, in the case of composite laminates, mechanical joint properties decrease because of lower interlaminar properties compared to in-plane properties around hole.?This study investigated needle punching process with the aim of improving the mechanical properties in the thickness direction of fiber-reinforced plastic composite laminates with an open hole. Needle punching process was applied to glass fiber chopped strand matused as the reinforcement for the composite laminates. Open-hole tensile tests and observations of end cross-sections after the tests were performed. The tensile properties and fracture mechanism of the specimens subjected to needle punching process were investigated. In addition, characteristic distance (a parameter for evaluating resistance to fracture in open-hole tensile test specimens) was also calculated to examine the effects of needle punching process conditions on fracture toughness. Tensile strength was improved by more than 15% by needle punching process. However, when a certain needle punching density was exceeded, the mechanical properties worsened. In addition, characteristic distance increased with increasing needle punching density. Thus, these results suggest that there is an optimal needle punching density with respect to strength and characteristic distance.
