MAGNETOHYDRODYNAMIC PIPE FLOW IN DUCTS WITH PARTIAL CIRCULAR RING CROSS SECTION AND ANNULAR CROSS SECTION

In this paper we use the Green function method to solve the problem of steady one dimensional flow of an incompressible viscous, electrically conducting fluid through a pipe with partial circular ring cross sec- tion and one with annular cross section, in the presence of an applied transverse uniform magnetic field, We ob- tain analytic solutions and carry out some numerical calculations of the velocity distribution and induced magnet- ic field.

RESEARCH ON THE ON-LINE MEASURING SYSTEM FOR THE MIDDLE-CONVEX AND VARYING ELLIPSE PISTON SKIRT

The middle convex and varying ellipse piston is th e key component of an internal combustion engine In general,the piston is mac hined by non circular section CNC lathe,but the measuring of piston profile is manipulated by off line Because the off line measuring reference is differen t from the machining reference,the measurement result is diverse from the act ual dimension A new method to measure the middle convex and varying ellipse p iston profile, which is known as on line measuring, is presented By using thi s kind of method,the high measurement accuracy can be gained,as well as meeting the production requirement.

Full-Range Compressive Stress-Strain Curves for Cold-Formed 304 Stainless Steel Circular Hollow Sections After Exposure to Vacuum Brazing

With the rapid development of microscale cellular structures, the small-diameter cold-formed welded stainless steel tubes have recently been used for creating the metallic lat- tice topologies with high mechanical properties. In this paper, to obtain the accurate material properties of the circular hollow section （CHS） under pure compression, a series of concentric compression tests are conducted on the millimeter-scale cold-formed 304 stainless steel circu- lar tubular stub columns after exposure to a vacuum brazing process. The tests cover a total of 18 small-diameter stub tubes with measured thickness-to-diameter ratios （t/D） from 0.023 to 0.201. A generalized three-stage nominal stress-strain model is developed for describing the compressive behavior of the post-brazing CHSs over the full strain range. This mechanical model is especially applicable to computer code implementation. Hence, an interactive computer pro- gram is developed to simultaneously optimize three strain hardening exponents （n1, n2, n3） in the expression of the model to produce the stress-strain curve capable of accurately replicating the test data. To further reduce the number of the model and material parameters on which this model depends, this paper also develops five expressions for determining the 2.5% proof stress （ap2）, n2, the ultimate compressive strength （σp3）, n3, and the ultimate plastic strain （p3%） for given experimental values of three basic material parameters （E0, σ0.01, σ0.2）. These expressions are validated to he effective for the CHSs with t/D 〉_ 0.027. The analytically predicted full-range stress-strain curves have generally shown close agreement with the ones obtained experimentally.

Experimental Study of the Shear Capacity of Glass Fiber Reinforced Polymer Reinforced Concrete Beam with Circular Cross Section

In order to research the shear behavior of glass fiber reinforced polymer (GFRP) reinforced concrete beam with circular cross section, based on the test results of 36 concrete beams subjected to four-point loading up to failure, the shear capacity and mechanical properties of deformation were analyzed comparatively between GFRP reinforced concrete (GFRP-RC) beams and steel reinforced concrete (steel-RC) beams. Furthermore, influencing factors of shear capacity of GFRP-RC beam with circular cross section were also investigated. The test results indicate that the failure modes of GFRP-RC and steel-RC beams are the same, but the crack patterns are slightly different. And, the shear capacity of GFRP-RC beam firstly increases with the reduction of shear span ratio, and then decreases. In addition, it was found that the influencing coefficient of GFRP on concrete increases with shear span ratio reducing.

A toughness based deformation limit for X- and K-joints under brace axial tension

This study reports a deformation limit for the initiation of ductile fracture failure in fatigue-cracked circular hollow section （CHS） X- and K-joints subjected to brace axial tension. The proposed approach sets the deformation limit as the numerically computed crack driving force in a fatigue crack at the hot-spot location in the tubular joint reaches the material fracture toughness measured from standard fracture specimens. The calibration of the numerical procedure predicates on reported numerical computations on the crack driving force and previously published verification study against large-scale CHS X-joints with fatigue generated surface cracks. The development of the deformation limit includes a normalization procedure, which covers a wide range of the geometric parameters and material toughness levels. The lower-bound deformation limits thus developed follow a linear relationship with respect to the crack-depth ratio for both X- and K-joints. Comparison of the predicated deformation limit against experimental on cracked tubular X- and K- joints demonstrates the conservative nature of the proposed deformation limit. The proposed deformation limit, when extrapolated to a zero crack depth, provides an estimate on the deformation limits for intact X- and K-joints under brace axial loads.